Yarisworld Archive

Bi-Level Storage Mod Complete...

22 posts · 12,801 views

IdjiitOriginal postHolly Springs, NC · Jul 20, 2006#1
I'd mentioned in the thread where I discussed taking out the backseats that I was going to be putting in storage for my photo gear. Well, here it is, complete.

Unfortunately I didn't document the whole process because, well... it took forever and I can't imagine anyone else following the same steps. But the basics is that it's constructed of 3/4" aluminum square stock, various brackets, 1/4 plywood and a shitload of screws. It has been covered in thin indoor/outdoor carpet. All in all, it's quite light. I don't think I'm over stock weight at this point, and it's possible I'm a bit under. The non-carpeted version of this went on a 12hr trip and the car got 41mpg, so it certainly isn't hampering anything. So far no squeaks/rattles, but I suspect that will change with time.

Bottom portion - about 1 1/2 inches off the bottom of the car frame to avoid hitting the gas tank "bubble" and the spare-tire flange:

Picture not included in this copy

3/4 view
Picture not included in this copy

Note the carriage bolts in the channels - used for locking in the top section, which will be shown later:
Picture not included in this copy

Horizontal view, note the dog grate and the plexiglass panels on the edges (so I can actually see):
Picture not included in this copy

From the passenger door
Picture not included in this copy

Hitch pins at the top, which can be pulled out...
Picture not included in this copy

...so the grate can come forward so you can fit the tables in (more on that later). I may replace the bolts at the bottom with hitchpins as well so you can just remove the whole thing.
Picture not included in this copy

First of two table slid in - this is aluminum as well, with a formica top. The table locks to the subframe through 4 "keyholes". This isn't so much for security per se, but to keep things from rattling around and to protect the dogs from getting crushed by the gear in a rollover crash.
Picture not included in this copy

Second table and the "locking portion" in place:
Picture not included in this copy

The "locking" piece. Since the two tables slide and lock in opposite directions (away from the middle) the locking portion simply prevents them from backing out of their "locked" positions:
Picture not included in this copy

Since the tables will stay in most of the time, the grate is "hinged" right now so if I need extra room I can just lay the grate flat if I need to fit in a 2x4, etc.
Picture not included in this copy

The missing link here is one more carpet that goes over everything and velcros down so everything is "hidden" and so the dogs have something comfy to walk around on. They have a ton of room back there, which is great. The only downside is that since the platform is raise, you're looking at your dog's junk about 50% of the time. ;)

Oh, if you're wondering WTF those tables are for, they come out and are used as part of our onsite printing setup:

Picture not included in this copy

Replies 21

stuffyontario, canada · Jul 20, 2006#2
very innovative idjiit, this is the type of mod that i like, something that is suited to an individual's needs, very cool!
cadence220Springfield, mo · Jul 20, 2006#3
That's great! The grate looks cool as well. Just the thing I need for my four-leggers. How'd you do that?
ChinoCharlesOH · Jul 20, 2006#4
Bravo man. Great mod, I think everyone could think of a use for that.
heylookitsjamesRiverside CA · Jul 20, 2006#5
Beautifully executed.
fnkngrvIn The Hotbox · Jul 20, 2006#6
a work of art my friend....would prolly work great for kids too😁
Chris07LBNew Jersey · Jul 20, 2006#7
Originally Posted by heylookitsjames
Beautifully executed.
+1 👍 👏
rickoGeorgian Triangle Ont. · Jul 20, 2006#8
Very clean!!!!!! Congrats on a truly functional mod.
PixieDawnTampa, FL · Jul 20, 2006#9
That looks great are you planning on putting the back seat back in when not in use or is this a perm. change?
IdjiitThread starterHolly Springs, NC · Jul 20, 2006#10
Originally Posted by PixieDawn
That looks great are you planning on putting the back seat back in when not in use or is this a perm. change?
It's semi-permanent. There haven't been any structural changes to the car, but getting it in there is difficult enough that's it's not something you can just unbolt and take out for the weekend. I originally had that in mind, but the car is so small that to take advantage of all the space I had essentially build it inside the car instead of building it outside and then bringing it in - although some portions were built like that. In the long run it doesn't really matter - we have the Prius if we need to tote around passengers.

Thanks for the compliments, guys!
TRD_YarisAustin, Texas · Jul 22, 2006#11
I am VERY IMPRESSED!!!
Chaad32USA · Jul 22, 2006#12
Good job..
IdjiitThread starterHolly Springs, NC · Jul 24, 2006#13
I know some of you guys were interested in what we were doing photo-wise so here's some photos of the table setup we're using...

Here's some shots of the setup onsite...

The tables strapped down. All of the gear is out of the Pelicans at this point. The legs seen here all fold up into the tables themselves - very self-contained:
Picture not included in this copy


People viewing the Kiosks, my wife helping a couple with photo selection:
Picture not included in this copy

The "sidecar" is mainly for the printers and the "print machine" (the other two machines are dedicated Kiosk machines at this point. They have keyboards and mice attached to them facing the customers, and we can use the keyboard/trackpad on the laptops to control them from our side. It works wonderfully. A lot of people have jumped right in and figured out how to use Lightroom, and often times customers will help each other - a testament to the ease of use of Lightroom.
Picture not included in this copy

The view from our side:
Picture not included in this copy
Chris07LBNew Jersey · Jul 24, 2006#14
Awesome setup you guys have!!

Even cooler, that it all fits inside a LIFTBACK!!! 👏 👍 👍 🤘
srivinusCharlotte, NC · Jun 11, 2007#15
Hi Idjiit

I am photographer from Charlotte and saw the mods. I just picked up a Yaris because I wanted something with good gas mileage since I do a LOT of city driving and parallel parking. Figured I had a van for the bigger location stuff and the Yaris would be perfect for small location headshots.

I love the mods to the back. I was thinking of doing something similar and had not thought of the bi-level config. Got a question for you. Did you make the tables or did you buy them somewhere?


Sean Rivinus
PolrWht07Dayton, Ohio · Jun 11, 2007#16
Very cool. Too bad I can't fit a wrestling ring in my yaris, that'd help with my profession, haha.
churpTropical Minnesota · Jun 11, 2007#17
I have to start looking thru the old threads....Idjiit, you're a true craftsman.

🙇
joey1320Lakewood, Ohio · Jun 11, 2007#18
great work man!!!
like it was said before, this is the kind dyi that is suitable to a small portion of the yaris owners, but it shows the different ways the car can make somebody's life better. great!
ism3tSouthern California · Jun 11, 2007#19
well done sir, well done.
redyarisOrlando, FL · Jun 12, 2007#20
This is awesome...fantastic job!!!!

+1000 for the Yaris. A functional car that keeps getting more functional!
falkor_99OC · Jun 12, 2007#21
dude thats totally sweet... very nice and clean too
spookybathtubCalifornia · Apr 15, 2010#22
This is totally awesome! Removing the seats looks like something I could do myself, no problem, but I'm nervous about embarking on the fabrication process myself. Mind if I ask how much you ended up paying for all the parts and labor?