you want on the list i will put you on now.
Official Richard Holdener who wants to buy an intake manifold list
386 posts · 103,977 views · page 3 of 8
Replies continued
When will these be made? I may be able to save up the 700.
get on the list and it will be ready the end of november.
Don't worry peter, at 700 bucks a pop you aren't going to find many other people dumb enough to buy it. ridiculous...
Reading back through this....will you also test with various other add ons in addition to the prototype long tube header? For example say mods that most have made like pulleys, axle backs and headers currently offered so folks will have a vague idea what to expect as to function and power output?
In the book that I am finishing on B-segments cars, I have already tested the TRD axle back, aem CAI, TRD CAI, dropping the exhaust entirely, custom CAI, NOS nitrous and low-boost turbo as well as all the testing on the intake. I would like to run a direct back to back on the pulleys and the shorty header if someone would allow me to borrow them for testing.
Originally Posted by Klink10 ↑Reading back through this....will you also test with various other add ons in addition to the prototype long tube header? For example say mods that most have made like pulleys, axle backs and headers currently offered so folks will have a vague idea what to expect as to function and power output?
Not sure if I'm reading this right. Is this an opinion that the power gains offered by the intake are not worth the retail price? This seems odd since the gains from the intake are greater than a CAI, axle back, pulleys and shorty header combined. I am curious to see what you think is a good performance buy.
Originally Posted by bladesmith6 ↑Don't worry peter, at 700 bucks a pop you aren't going to find many other people dumb enough to buy it. ridiculous...
I need a couple days to make the decision. This is why I'm asking you now so I don't waste your time then. When is the last day I can get in on this?Originally Posted by kou ↑you want on the list i will put you on now.
The first production run will have to be more than 10, but make sure to get your name on the list since those people will get their intakes for sure and any that may be left will be offered for sale. I doubt there will be much in the way of excess.
Originally Posted by me_ver51 ↑I need a couple days to make the decision. This is why I'm asking you now so I don't waste your time then. When is the last day I can get in on this?
I honestly think you are mistaken. $700 is a good chunk of change, but the price/pony ratio is definitely worth every penny.Originally Posted by bladesmith6 ↑Don't worry peter, at 700 bucks a pop you aren't going to find many other people dumb enough to buy it. ridiculous...
Sure, I would've preferred the mani with better gains at the bottom/mid range, but this is still a great buy in my book.
Rich I wish I could provide those pieces for you, however my car wouldn't run if I did. Having said what you have done (B cars), I assume you are happy with the results or we wouldn't be where we are today. So, I am looking forward to the conclusion and again thanks.
you started making them yet!?
engrave "peterpoop" into mine. j/j
engrave "peterpoop" into mine. j/j
Ok, here is my opinion since apparently I am the only one who feels this way(or hasn't lost their perspective) I don't give a damn about the "horsepower to dollar ratio" that everyone keeps yammering about. I am talking purely about price for a certain type of part. For a non race manifold you generally see around 250-550 dollars, now I'm sure this manifold is the same basic construction, flange, 4 tubes, air chamber nothing earth shattering. No space age materials, no moving parts, no magic. Those manifolds are pumped out at a factory so prices can be lower because of volume, yours is closer to hand made, so no argument there. So sell the plans to edelbrock or victor or whomever you want, let THEM provide your profit margin instead of extorting a group of people who bought a subcompact car and are trying to have a little fun with what they can afford. Obviously the second I post this everyone who put themselves on the list is going to jump me saying how justified the price is, but I can't help thinking it is only because they have nowhere else to go.
Supply and demand, bladesmith6... Supply and demand...
If you see a hole in the market for $500 manis, then get them made and sell them! Hell, if they're decent enough to compete with these manis I may even get one from ya.
Richard has spent a lot of time testing this part, and to me that is worth something. Plus, it's not like Joe the Plumber made it, now is it? 😉
If you see a hole in the market for $500 manis, then get them made and sell them! Hell, if they're decent enough to compete with these manis I may even get one from ya.
Richard has spent a lot of time testing this part, and to me that is worth something. Plus, it's not like Joe the Plumber made it, now is it? 😉
^^^^simple laws of supply and demand buddy. No1 else make them so there is nothing to put it up against to say if its a bargin or not.. no competition. I personally think its and ok price for it but i see your point and i think its valid.Originally Posted by bladesmith6 ↑Ok, here is my opinion since apparently I am the only one who feels this way(or hasn't lost their perspective) I don't give a damn about the "horsepower to dollar ratio" that everyone keeps yammering about. I am talking purely about price for a certain type of part. For a non race manifold you generally see around 250-550 dollars, now I'm sure this manifold is the same basic construction, flange, 4 tubes, air chamber nothing earth shattering. No space age materials, no moving parts, no magic. Those manifolds are pumped out at a factory so prices can be lower because of volume, yours is closer to hand made, so no argument there. So sell the plans to edelbrock or victor or whomever you want, let THEM provide your profit margin instead of extorting a group of people who bought a subcompact car and are trying to have a little fun with what they can afford. Obviously the second I post this everyone who put themselves on the list is going to jump me saying how justified the price is, but I can't help thinking it is only because they have nowhere else to go.
Of course he's going to charge extra. He did all the r&d and he's the first to offer this kind of part.Originally Posted by bladesmith6 ↑Ok, here is my opinion since apparently I am the only one who feels this way(or hasn't lost their perspective) I don't give a damn about the "horsepower to dollar ratio" that everyone keeps yammering about. I am talking purely about price for a certain type of part. For a non race manifold you generally see around 250-550 dollars, now I'm sure this manifold is the same basic construction, flange, 4 tubes, air chamber nothing earth shattering. No space age materials, no moving parts, no magic. Those manifolds are pumped out at a factory so prices can be lower because of volume, yours is closer to hand made, so no argument there. So sell the plans to edelbrock or victor or whomever you want, let THEM provide your profit margin instead of extorting a group of people who bought a subcompact car and are trying to have a little fun with what they can afford. Obviously the second I post this everyone who put themselves on the list is going to jump me saying how justified the price is, but I can't help thinking it is only because they have nowhere else to go.
If you don't want to pay the price, wait for a chinese company to make a cheap knock off and buy it on ebay for a 100$
i have spent more for less power so far,this is the missing link . the yaris may get a little scary on a cold nights up north.this little machine is surprising sometimes.
its cold down here now and o man it has a kik to it now. i actually feel tq :)
i'm buying it because noone else is making one. simple
i have dc 4-1 headaer NST underdrive pulleys and vegas local 🙂 i can lend u the car for a day 🙂Originally Posted by richardholdener ↑In the book that I am finishing on B-segments cars, I have already tested the TRD axle back, aem CAI, TRD CAI, dropping the exhaust entirely, custom CAI, NOS nitrous and low-boost turbo as well as all the testing on the intake. I would like to run a direct back to back on the pulleys and the shorty header if someone would allow me to borrow them for testing.
This is such great information, I hardly know where to start. Let me get this straight. All anyone has to do is connect 4 tubes to a flange and (what is you called it?) an air chamber and viola--its instant intake manifold. I think that is exactly what the OEMs do-I mean why go to the trouble of hiring engineers with degrees in fluidynamics when you can get all the information you need on intake design right here from Mr. Pinkblade. Here is an offer of a free intake manifold since it is obvious you can't afford to buy one (despite a favorable bang/buck score). I will give you a free intake if you can tell me what the three forms of charge filling are associated with an intake design. You may have guessed by now that there is much more to an intake manifold than your previous description (we call the earlier comments sarcasm). I'll throw in a free long-tube header if you can tell me what the problem is asssociated with combining the three forms. You have all of the internet and every book ever written to source the information-you have 1 week.
PS-I welcome you to build your own manifold, start by running extensive testing on a minimum of 50 different intake combinations, then produce a 1st article and do a production run. You may want to check out the current cost of aluminum, welding time, fixture manufacturing, CNC machine work, tube bending, gaskets, vacuum and water lines to say nothing of your time. Please let me know if you can build an intake like this one for $250 so I can purchase them in bulk.
PS-I welcome you to build your own manifold, start by running extensive testing on a minimum of 50 different intake combinations, then produce a 1st article and do a production run. You may want to check out the current cost of aluminum, welding time, fixture manufacturing, CNC machine work, tube bending, gaskets, vacuum and water lines to say nothing of your time. Please let me know if you can build an intake like this one for $250 so I can purchase them in bulk.
Originally Posted by bladesmith6 ↑Ok, here is my opinion since apparently I am the only one who feels this way(or hasn't lost their perspective) I don't give a damn about the "horsepower to dollar ratio" that everyone keeps yammering about. I am talking purely about price for a certain type of part. For a non race manifold you generally see around 250-550 dollars, now I'm sure this manifold is the same basic construction, flange, 4 tubes, air chamber nothing earth shattering. No space age materials, no moving parts, no magic. Those manifolds are pumped out at a factory so prices can be lower because of volume, yours is closer to hand made, so no argument there. So sell the plans to edelbrock or victor or whomever you want, let THEM provide your profit margin instead of extorting a group of people who bought a subcompact car and are trying to have a little fun with what they can afford. Obviously the second I post this everyone who put themselves on the list is going to jump me saying how justified the price is, but I can't help thinking it is only because they have nowhere else to go.
I'll take that header :P It will just take me about 30 minutes to type up the post.
Oh man. Served.
PWNED
*grabs popcorn and sits in his favorite sofa*
Sadly, that's the kind of attitude that seems to make a lot of manufacturers hesitate before making parts for a "cheap" car, I guess 🙁
Richard, don't let a bad apple spoil our bunch 🙂
now I'm gonna go off and collect some soda cans, PVC tubing and RTV silicone and make my own intake out of that 😎
Richard, don't let a bad apple spoil our bunch 🙂
now I'm gonna go off and collect some soda cans, PVC tubing and RTV silicone and make my own intake out of that 😎
Dude, you don't have to go into so much detail! It's been over 3 hours already! 😁Originally Posted by largeorangefont ↑I'll take that header :P It will just take me about 30 minutes to type up the post.
hey richard, what happens after the first ten are sold and shipped.is there gonna another group buy right away seeing as tax season is 3 months away??
11 and I believe you can still get on the list. Just needed 10 to get the ball rolling.
I will give you a free intake/mani if you can tell me .......Does these challenges apply to everyone 😁 😁
Yeah dude, for a custom piece that he produced this way for a small community that is a damn good price.
If you look online for custom manifolds cheapest you would find them would be $500 that are not mass produced and they are of crap design because they just slap them together with whatever size runners fit in the engine bay.
I think even $700 is on the cheap side for this product, but seeing that this is a cheap car to begin with i think it is a good price!
Oh and Richard, are you using velocity stacks, or are you just smoothing out the entry to the runners
^^^i hope. but prob not. would increase cost unless its already done and factored in...Originally Posted by Nexus1155 ↑Does these challenges apply to everyone 😁 😁
Yeah dude, for a custom piece that he produced this way for a small community that is a damn good price.
If you look online for custom manifolds cheapest you would find them would be $500 that are not mass produced and they are of crap design because they just slap them together with whatever size runners fit in the engine bay.
I think even $700 is on the cheap side for this product, but seeing that this is a cheap car to begin with i think it is a good price!
Oh and Richard, are you using velocity stacks, or are you just smoothing out the entry to the runners
Originally Posted by tk-421 ↑*grabs popcorn and sits in his favorite sofa*
I'll take some of that popcorn, thank you very much
Originally Posted by richardholdener ↑This is such great information, I hardly know where to start. Let me get this straight. All anyone has to do is connect 4 tubes to a flange and (what is you called it?) an air chamber and viola--its instant intake manifold. I think that is exactly what the OEMs do-I mean why go to the trouble of hiring engineers with degrees in fluidynamics when you can get all the information you need on intake design right here from Mr. Pinkblade. Here is an offer of a free intake manifold since it is obvious you can't afford to buy one (despite a favorable bang/buck score). I will give you a free intake if you can tell me what the three forms of charge filling are associated with an intake design. You may have guessed by now that there is much more to an intake manifold than your previous description (we call the earlier comments sarcasm). I'll throw in a free long-tube header if you can tell me what the problem is asssociated with combining the three forms. You have all of the internet and every book ever written to source the information-you have 1 week.
PS-I welcome you to build your own manifold, start by running extensive testing on a minimum of 50 different intake combinations, then produce a 1st article and do a production run. You may want to check out the current cost of aluminum, welding time, fixture manufacturing, CNC machine work, tube bending, gaskets, vacuum and water lines to say nothing of your time. Please let me know if you can build an intake like this one for $250 so I can purchase them in bulk.
Richard are you saying you have done all that with the making of the Yaris Manifold? You showing a dyno must say there is a protoype of some sort!
You stated in the posting of the dyno! I quote"Here is the dyno grap of the stock vs new intake that was removed previously."
Is there a reason for not showing the one that was previously remove. To give the forum a better idea of what they are committing to?
Also quoting you from another post. "leaves me with no motor to develope the intake manifold-we have removed the damaged motor"
Develop an intake manifold? I thought by showing a dyno of the gains you would have a manifold?
I am just trying to put all this info together!
Please if you can explain!
thanks
Richard Holdener has been around for many, many years and was an inspiration of mine back in the early 90's when he had his Vortech Supercharged Mustang Sedan. He also has built the fastest civic I believe and was ran on the salt flats. Although time in the industry isnt everything, take a look around and find out who you are accusing of not knowing anything. Richard has done more for the aftermarket indusrty then most of you younger people can imagine.
was that the civic in a mag with the moon disc wheel covers ^^^ !!!!! if so i have that mag
i think this is him richard holdener before and after
2 attachments not included in this copy
I will give you a free intake if you can tell me what the three forms of charge filling are associated with an intake design. You may have guessed by now that there is much more to an intake manifold than your previous description (we call the earlier comments sarcasm). I'll throw in a free long-tube header if you can tell me what the problem is asssociated with combining the three forms. You have all of the internet and every book ever written to source the information-you have 1 week.Ok Here i go... charge filling .. what is that layman's speak! The only 3 things you'll need are as follows: Duck Tape.. Aluminum.. and some more ducktape with coke... ok here i go
The problem with combining these 3 so called "charge fillings" is that.. As you many know, Coke doesn't go well with aluminum. So the trick is not to touch them. You get sheets of aluminum and put them in the right places... duck tape them together right? Then drink some coke along the way, but don't drink all of it you will need some later. Once you've buffed out the ruffs you add some more duck tape then buff again. Once it's all done.... You get the remaining coke, should be 240 ml of it. you pour some through the system and make sure there are no leaks. Bingo you've got yourself a beautiful top of the line intake manifold. The remaining coke is used to pour on the manifold itself as to give it a tint.(the coke can only go on at this point.. Before and it will destroy the aluminum.. after and it will not tint) Makes for a great tint for car shows... Viola!
P.S. does this mean ill be getting a mani and a header? Gosh Darnit I Hope so!
Our man Richard has done some boooks too...
http://www.amazon.com/exec/obidos/se...ard%20Holdener
A little more about the man..
Picture not included in this copy
Richard Holdener was born in Washington D.C. but his family moved almost immediately to California. His first automotive experience came with his father at a car show. After viewing all of the elaborate horsepower hard-ware, Richard was hooked on going fast.
Richard’s garage has been home to a variety of high-performance machinery. The list includes a couple of Camaros, a Lotus-motored Jensen Healy, a 260 Z, a 230SL Mercedes, a 1972 911T, a blown crewcab Dualie, a pair of Hondas (one supercharged Civic Si), a Toyota Corolla, a Mercedes 450 SEL, and trio of hot motorcycles. First came the Honda 500 Interceptor, then the 600 Ninja, and finally the GSX-R750. Somewhere in all this madness came a 1965 Hipo GT and a trio of 5.0L Mustangs.
Richard’s first article came from his Mustang adventures at the Silver State. Since this initial coverage, Richard has contributed to numerous magazines, including Muscle Mustangs & Fast Fords, Car Craft, Super Ford, Truckin’, Mustang Illustrated, Popular Hotrodding, Sport CompactCar, European Car, Pontiac Enthusiast, and many others.
I feel pretty confident with this guy and the manifold i'll be getting! 🤘🤘
http://www.amazon.com/exec/obidos/se...ard%20Holdener
A little more about the man..
Picture not included in this copy
Richard Holdener was born in Washington D.C. but his family moved almost immediately to California. His first automotive experience came with his father at a car show. After viewing all of the elaborate horsepower hard-ware, Richard was hooked on going fast.
Richard’s garage has been home to a variety of high-performance machinery. The list includes a couple of Camaros, a Lotus-motored Jensen Healy, a 260 Z, a 230SL Mercedes, a 1972 911T, a blown crewcab Dualie, a pair of Hondas (one supercharged Civic Si), a Toyota Corolla, a Mercedes 450 SEL, and trio of hot motorcycles. First came the Honda 500 Interceptor, then the 600 Ninja, and finally the GSX-R750. Somewhere in all this madness came a 1965 Hipo GT and a trio of 5.0L Mustangs.
Richard’s first article came from his Mustang adventures at the Silver State. Since this initial coverage, Richard has contributed to numerous magazines, including Muscle Mustangs & Fast Fords, Car Craft, Super Ford, Truckin’, Mustang Illustrated, Popular Hotrodding, Sport CompactCar, European Car, Pontiac Enthusiast, and many others.
I feel pretty confident with this guy and the manifold i'll be getting! 🤘🤘
TheRealEnth, I believe it is "duct" tape and not "duck" tape... no mani for you. 😆
Failed at life -.- =(
Wow thanks for all the info. nice info is.
Plus google corrects his name, magic I tell you.
Picture not included in this copy
Picture not included in this copy
Man common guys those questions were for Richard to answer. I did do the google search to before i posted. I know his background which is very extensive and long. I commend Richard on his long track record and experience.
You guys turned my questions for him around into a "I don't know who Richard is thread" please stay on topic too...
I am fully aware who he is and have owned one of his books before ok!
I said i am just trying to put all the posts together. Is anyone really reading what I am asking.
You guys turned my questions for him around into a "I don't know who Richard is thread" please stay on topic too...
I am fully aware who he is and have owned one of his books before ok!
I said i am just trying to put all the posts together. Is anyone really reading what I am asking.
he hasn't signed on yet today. he'll probably answer it when he gets on.
Richard is busy making maifolds.
Design does include radiused entries (bellmouth tubing).
Originally Posted by Yoda ↑^^^i hope. but prob not. would increase cost unless its already done and factored in...
Second photo is actually Robery Pond who specializes in FE Ford motors-thats a 482 stroker than made 640 hp.
Originally Posted by marcus ↑i think this is him richard holdener before and after
Please take a look at this and the other posts under intake manifold. The prototype has been tested the only necessary is to get the design to fit toproduce the production piece. Fitment will not change design parameters that produce desired power curve.
Originally Posted by cee_dub2003 ↑Richard are you saying you have done all that with the making of the Yaris Manifold? You showing a dyno must say there is a protoype of some sort!
You stated in the posting of the dyno! I quote"Here is the dyno grap of the stock vs new intake that was removed previously."
Is there a reason for not showing the one that was previously remove. To give the forum a better idea of what they are committing to?
Also quoting you from another post. "leaves me with no motor to develope the intake manifold-we have removed the damaged motor"
Develop an intake manifold? I thought by showing a dyno of the gains you would have a manifold?
I am just trying to put all this info together!
Please if you can explain!
thanks
We ran the Civic in Sept 08 at Speed Week (Bonnevile) and set a (2-way) new land speed record of 226.5 mph-making it still the world's fastest honda civic. PS-car was on track to run 235 mph but we broke a CV joint at the 4th mile marker (Bonneville is 5 miles in length). Pretty wild ride having the CV let go at 227 mph! Good in-car footage of parachute saving my bacon!
Originally Posted by Nexus1155 ↑was that the civic in a mag with the moon disc wheel covers ^^^ !!!!! if so i have that mag
Actually you had it all right except its Pepsi and not Coke! NO mani for you!
Originally Posted by TheRealEnth ↑Ok Here i go... charge filling .. what is that layman's speak! The only 3 things you'll need are as follows: Duck Tape.. Aluminum.. and some more ducktape with coke... ok here i go
The problem with combining these 3 so called "charge fillings" is that.. As you many know, Coke doesn't go well with aluminum. So the trick is not to touch them. You get sheets of aluminum and put them in the right places... duck tape them together right? Then drink some coke along the way, but don't drink all of it you will need some later. Once you've buffed out the ruffs you add some more duck tape then buff again. Once it's all done.... You get the remaining coke, should be 240 ml of it. you pour some through the system and make sure there are no leaks. Bingo you've got yourself a beautiful top of the line intake manifold. The remaining coke is used to pour on the manifold itself as to give it a tint.(the coke can only go on at this point.. Before and it will destroy the aluminum.. after and it will not tint) Makes for a great tint for car shows... Viola!
P.S. does this mean ill be getting a mani and a header? Gosh Darnit I Hope so!