Yarisworld Archive

Alternative rear disc conversion?

132 posts · 350,166 views · page 1 of 3

NeinrisOriginal post‘Murica! · Mar 8, 2021#1
Alright, here we go...

I've known about this for quite a while, almost 2 years now. Not sure if this is more cost effective than swapping the rear axle with the 2012+ SE.

I've found this thread from another Toyota forum, and it's not even about the Yaris, it's a 10th GEN Corolla.

https://www.toyotanation.com/threads...e-swap.390125/

BLUF:
This involves installing bracket plates for the calipers to mount on. Part numbers of said plates/splash shields are 47803-02020 (right) and 47804-02020 (left).
IF these plates in fact fits on the Yaris, it could be a game changer. You wouldn't need to swap out the whole axle, and your wheels will stick out 10mm farther, which would then make the rear wheels stick out more than the front, which I don't mind.
I kind of wanted to be the first to do it, but I'm sharing it now to see if anyone dares to try it out, and I don't really have the funds right now.

I know most would argue that these light cars don't really need disc brakes in the back, blah, blah, blah... If you're not interested, you can stop reading. But for those who are curious, this might be worth your while.

Here are most of the parts that the other poster used for his rear disc brake conversion (my apologies, I can't seem to copy the table but I hope you can still figure out what category falls where):

P/N Quantity Price EA Description
0446602310 1 $ 40.88 Disc Brake Pad Set (Rear)
4780402020 1 $ 122.13 Brake Dust Shield (Left, Rear)
4780302020 1 $ 122.13 Brake Dust Shield (Right, Rear)
90947A2023 2 $ 46.13 Brake Hydraulic Hose (Right, Rear)
4782102160 2 $ 96.43 Disc Brake Caliper Bracket (Left, Right, Rear) Mounting, Disc Brake Cylinder. A bracket for a disc brake caliper.
4785002180 1 $ 150.51 Disc Brake Caliper (Left, Rear)
4783002180 1 $ 150.51 Disc Brake Caliper (Right, Rear)
4243102200 2 $ 53.31 Disc Brake Rotor (Rear) A single disc brake rotor
4642002151 1 $60.27 E-Brake R
4643002151 1 $60.27 E-Brake L

The big thing that I want to point out, P/N 42431-02200, has the same dimension as P/N 42431-52080, which is the part number for the 2012 Yaris SE rear rotor. Do I have your attention now?
So, first things first to get this to work, the splash guard would have to fit on the Yaris, if not, we're dead on the water. Next, need to sort out what else from that list can be used on the Yaris, well some are straightforward, the calipers can be used, and the pads, since the rotors are the same dimension. And finally, is this more cost effective than the axle swap? Probably easier to tackle than the axle swap, especially if you're by yourself.

There you have it Ladies, another stupid idea from me. I hope someone is crazy enough to test it out before me. 😁

Replies 131

remcafeeArizona · Mar 8, 2021#2
well it certainly is an alternative i personally do not like the fact of have a whole different rear suspension geometry not designed for our cars but for a corolla, having the rear wheel stance out would not make sense as our front end needs major help already, if its for a look thing i guess, but the yaris se rear disc swap is perfect as their is no change in rear suspension gemoetry and everything still lines up as the factory would want, the corolla brackets and mounting holes physically look larger than ours, once i see an old corolla roll through our dealer ill take a peek and let you guys know though. edit: just realized youre not doing anything to disturbe rear axle positioning but just hub length and flange thickness, i think it would work just waiting to find an old corolla come in so i can measure the length and height of the flange thickness on the corolla axle
NeinrisThread starter‘Murica! · Mar 8, 2021#3
Originally Posted by remcafee ↑
well it certainly is an alternative i personally do not like the fact of have a whole different rear suspension geometry not designed for our cars but for a corolla, having the rear wheel stance out would not make sense as our front end needs major help already, if its for a look thing i guess, but the yaris se rear disc swap is perfect as their is no change in rear suspension gemoetry and everything still lines up as the factory would want, the corolla brackets and mounting holes physically look larger than ours, once i see an old corolla roll through our dealer ill take a peek and let you guys know though. edit: just realized youre not doing anything to disturbe rear axle positioning but just hub length and flange thickness, i think it would work just waiting to find an old corolla come in so i can measure the length and height of the flange thickness on the corolla axle
Remcafee, thank you! I appreciate you taking the measurements. I hope this takes off.
06YarisRSFredericton, New Brunswick, Canada · Mar 8, 2021#4
Sub'd. This is something I've thought would be a great upgrade. Would there be any issues with fluid metering and balancing of brake forces front to rear? The Yaris brakes must be designed to distribute a specific force per axle. The caliper pistons are surely much larger in surface area than the tiny wheel cylinder pistons. I'm no fluid dynamics engineer, but I do wonder about this. Do the rear disk and rear drum cars use the same master cylinder?

EDIT: Not positive, but the 2008 Vitz RS uses master cylinder (47201-52280) and 2008 Yaris uses (47201-52320). May not make any difference.
NeinrisThread starter‘Murica! · Mar 8, 2021#5
Originally Posted by 06YarisRS ↑
Sub'd. This is something I've thought would be a great upgrade. Would there be any issues with fluid metering and balancing of brake forces front to rear? The Yaris brakes must be designed to distribute a specific force per axle. The caliper pistons are surely much larger in surface area than the tiny wheel cylinder pistons. I'm no fluid dynamics engineer, but I do wonder about this. Do the rear disk and rear drum cars use the same master cylinder?
Adam, at another thread it's mentioned that if you have ABS you're fine without having to install a proportioning valve. If you don't have ABS, it's is highly recommended that you install one. It's not really that hard to install one, I was trying to argue if having braided lines on the front, and regular lines on the rear would suffice, but that's not advisable neither.
Obviously if or WHEN I do this, I'll be installing the bigger rotors in front. The stock front rotors are 255mm in diameter, the SE rear rotors are 259mm, and the SE front rotors are 275mm. Most of you already knew that.
06YarisRSFredericton, New Brunswick, Canada · Mar 8, 2021#6
Originally Posted by Neinris ↑
Adam, at another thread it's mentioned that if you have ABS you're fine without having to install a proportioning valve. If you don't have ABS, it's is highly recommended that you install one. It's not really that hard to install one, I was trying to argue if having braided lines on the front, and regular lines on the rear would suffice, but that's not advisable neither.
Obviously if or WHEN I do this, I'll be installing the bigger rotors in front. The stock front rotors are 255mm in diameter, the SE rear rotors are 259mm, and the SE front rotors are 275mm. Most of you already knew that.
Haha, not 5 minutes after posting, I scrolled down and saw the other thread. 🙄 This may sound completely silly, but I'm not sure if I have ABS or not on my 2006. Haha. Pretty sure my old '08 did. Going to go look at my wiring diagrams. 👍

EDIT: Guess this answers my own question:

Picture not included in this copy
remcafeeArizona · Mar 8, 2021#7
yeah the abs is actually wonderful in our cars it has electronic brake force distribution and meters brake proportioning electronically not just front and rear both EACH individual wheel separately from one another, so if you dont have abs youre actually gonna have to do more work lol
enviriCT · Mar 8, 2021#8
its been talked to death. no one has done it. do it, make it happen. people will credit you.
I've used XRS pads before the '12 SE was out so yeah its pretty good on dimensions.

just hope the hub bolts line up :P
NeinrisThread starter‘Murica! · Mar 9, 2021#9
Originally Posted by enviri ↑
its been talked to death. no one has done it. do it, make it happen. people will credit you.
I've used XRS pads before the '12 SE was out so yeah its pretty good on dimensions.

just hope the hub bolts line up :P
WOW! I even got Enviri’s attention! What an honor!
Not sure what you’re referring to when you said “talked to death”.
All I’m doing is bring the idea to give others a possible other option. If I do this it’d be in a distant future, I’d rather spent my money on the engine swap. And besides, my other dumb idea is to try and see if the 2nd GEN Scion xB’s rear axle frame fits the Yaris. Can you say 5X114.3?
remcafeeArizona · Mar 9, 2021#10
i found a rear axle beam from a yaris se with the calipers and everything they left on it for about $240 its not as pricey as you think assuming you get junkyard parts and its perfect fitment for our cars, if its cost youre worried about, have a fabrication shop weld on some rear caliper brackets to your rear axle beam and youre good to go, just source the calipers and lines and such afterwards
NeinrisThread starter‘Murica! · Mar 9, 2021#11
Originally Posted by remcafee ↑
i found a rear axle beam from a yaris se with the calipers and everything they left on it for about $240 its not as pricey as you think assuming you get junkyard parts and its perfect fitment for our cars, if its cost youre worried about, have a fabrication shop weld on some rear caliper brackets to your rear axle beam and youre good to go, just source the calipers and lines and such afterwards
It really all comes down to cost, and availability. Who would want to pay more for something if they can get it for less? The other poster bought everything brand new, of course it'd be more expensive. They can also be found from the the junk yard. Are the Yaris SE more abundant than the Corolla and I think Matrix that the splash guards/back plate came from?

Getting it welded crossed my mind, but my aim is a DIY for the mass. Also it could be slightly off and make the pads wear irregularly. Another thing that crossed my mind was tracing the back plate from the SE and getting one made and slapping it on top. But since I came across the other thread I thought it'd be cheaper to get the splash guards than getting one manufactured.

I need to get my vapor canister and pump replaced. I was going to scower the junk yard for one, maybe I'll scower for a splash guard as well and see how it fits.
enviriCT · Mar 10, 2021#12
yaris se and corolla XRS...the numbers may be similarly small!! the biggest thing is if that caliper mount matches with our hubs, everything else is trivial. if that caliper mount fits a yaris rear caliper also, then holy crap. My original idea is to make a hubspacer with caliper mounts, and did consider the xb2 rear shield but it wont fit.

since when did i become famous?
NeinrisThread starter‘Murica! · Mar 10, 2021#13
Originally Posted by enviri ↑
yaris se and corolla XRS...the numbers may be similarly small!! the biggest thing is if that caliper mount matches with our hubs, everything else is trivial. if that caliper mount fits a yaris rear caliper also, then holy crap. My original idea is to make a hubspacer with caliper mounts, and did consider the xb2 rear shield but it wont fit.

since when did i become famous?
LOL! Always been famous to me, I’ve seen your name around. Almost up there with CTScott in my book.
The thought I have with xB2 is a complete axle frame swap to try switching to 5x114.3. The axle has the same spline count as the Yaris, so swapping the steering knuckle might be an option. That’s for another story.
Like I said, I too thought about tracing the SE hub mount and getting a plate made, but it might be more expensive to get manufactured.
Well I hope me sharing this inspires others to try it out. Gonna go to the junkyard this weekend. Crossing my fingers...
CrankyOldManWest Michigan · Mar 11, 2021#14
I have an SE rear axle in the garage and there's a 10th gen Corolla in the local junk yard but it only has drum brakes. If I could pull the rear hub I could at least compare bolt patterns and bore diameter since the hub is common to all variants of that gen Corolla.
NeinrisThread starter‘Murica! · Mar 11, 2021#15
Originally Posted by CrankyOldMan ↑
I have an SE rear axle in the garage and there's a 10th gen Corolla in the local junk yard but it only has drum brakes. If I could pull the rear hub I could at least compare bolt patterns and bore diameter since the hub is common to all variants of that gen Corolla.
OH MAN! Now we Cranky involved!!!

Please do! I may or may not find a XRS in the junk yard, I'm sure I'm not the only one who would appreciate it.
enviriCT · Mar 11, 2021#16
apparently the rear dust shield extends to 2019....maybe other parts. trying to find them used :P
NeinrisThread starter‘Murica! · Mar 11, 2021#17
Originally Posted by enviri ↑
apparently the rear dust shield extends to 2019....maybe other parts. trying to find them used :P
Cool! Cool! I guess I’ll just start looking for Corollas with rear disc brakes in the junk yard. The evap canister are also similar if not the same. So might be two birds with one stone.
NeinrisThread starter‘Murica! · Mar 12, 2021#18
Went to the pick and pull today, couldn’t find a Corolla with rear disc brakes. I tried pulling out a hub from one of the, but it was really on there. The other ones were sitting on mud, so I didn’t bother. I’ll try another pick and pull this weekend.
remcafeeArizona · Mar 13, 2021#19
sometimes you gotta give them a good smacking with a hammer, but as long as the 4 bolts are loose it should come out
NeinrisThread starter‘Murica! · Mar 16, 2021#20
Looks like the LKQ near me near me just added a 2015 Corolla in their inventory. I'll check if it has rear disc brakes while I'm there trying to grab other things. Stay tuned! 😁
NeinrisThread starter‘Murica! · Mar 16, 2021#21
Ok... So the 2015 Corolla has rear disc brakes, I took them off and hid them for now... 😆 I bought just the right splash guard for now. I guess we’ll test fit this weekend, and if it works, then I’m off to grab the rest of them, I was even careful to remove the e-brake cables, I hope those will work as well. Crossing my fingers!!!

2 attachments not included in this copy

06YarisRSFredericton, New Brunswick, Canada · Mar 16, 2021#22
👍 Great work! Can't wait for the outcome.
enviriCT · Mar 17, 2021#23
that bolt pattern looks almost square....im already worried. lining it up via photoshop (i have a spare rear hub) made my assumption worse.
NeinrisThread starter‘Murica! · Mar 17, 2021#24
I took more pics and made it as parallel the the plate as I can, as you all know, the image can get distorted if not taken perfectly squared. I also made some measurements, I’m probably off by +|- 3mm, but I eyeballed the center of the holes the best I can. Can you take measurements?

4 attachments not included in this copy

enviriCT · Mar 17, 2021#25
ooo a digital caliper. so fancy.
enviriCT · Mar 17, 2021#26
pics may be too big?

3 attachments not included in this copy

NeinrisThread starter‘Murica! · Mar 17, 2021#27
Originally Posted by enviri ↑
ooo a digital caliper. so fancy.
😆 😆 😆

It's actually garbage, got it from Auto Zone, didn't know it's made of plastic. Sigh...
enviriCT · Mar 17, 2021#28
i might have a caliper in my trunk, but then i have to carry my 1nz head OFF the trunk...meh.
NeinrisThread starter‘Murica! · Mar 17, 2021#29
Originally Posted by enviri ↑
pics may be too big?
Hmmm... it's not looking good. 🙁
But I won't let that discourage me, I'll still do a fitment test. Crossing my fingers. 😳
remcafeeArizona · Mar 17, 2021#30
hmmm its a completely different design than our yaris, the caliper mounting holes are part of the dust shield, interesting, it looks awfully thicker than the yariss hub from the side pics im thinking it may need to shim the hubs (assuming they fit) so that the rear disc brakes wont be dragging sice they arent at the right angle
NeinrisThread starter‘Murica! · Mar 18, 2021#31
Originally Posted by remcafee ↑
hmmm its a completely different design than our yaris, the caliper mounting holes are part of the dust shield, interesting, it looks awfully thicker than the yariss hub from the side pics im thinking it may need to shim the hubs (assuming they fit) so that the rear disc brakes wont be dragging sice they arent at the right angle
Sorry, I didn't get what you mean by it not being the right angle? Maybe you're talking about using the calipers from the Yaris SE? For this build you'd have use the calipers that came with the car, which is what I was planning all along.

Anyway, the difference how the Corolla and the Yaris bolts their rear hubs are that the Corolla's bolts comes from the back, the threads are on the hubs, while the Yaris bolts comes from the front, the threads are on the axle frame. I've tested the bolts that came with the splash guard, they thread in the mounting holes, and they're longer too. They have washer on them, which I'd probably remove to make sure they'd thread through all the way.

I just measured how thick the mounting face is, it's 11mm with the splash guard. Which means the wheels will stick out that much further. I'm fine with that, since the rear are tucked in more than the front anyway. If this works, the wheels will 6mm further than the front, 12mm total. According to this video, the front is 1470mm wide and the rear 1460mm, around 2:48 in the time stamp:

https://www.youtube.com/watch?v=GuEcY4RwS50&t=170s

I tried to remove the rear passenger hub after work today, but I got bested by it. I forgot to take measurements, I was in a hurry as I was running out of daylight. I'll buy two long bolts of the same thread size, nuts, and washers from Home Depot tomorrow, I should be able to safely back it out using the same method done in this video:

https://www.youtube.com/watch?v=7nj_KUkASxg

All in all, I just wish the center hole is the same size. If the mounting holes don't lineup, I'd probably get them filled with weld and drill the correct holes in them. Hopefully I don't have to resort to that. 😳
enviriCT · Mar 18, 2021#32
there might be some shaving to be done to the dust shield around the top to fit the yaris axle mount indeed.. have fun!
NeinrisThread starter‘Murica! · Mar 18, 2021#33
Well, I’m a little disappointed that the mounting holes didn’t lineup, not a single one, but the center hole is the same size so there’s still hope. I’m going to continue this project, but I’ll postpone it for now.

1 attachment not included in this copy

enviriCT · Mar 18, 2021#34
fill and redrill, find a machinist, mass produce. or make a hub spacer and screw the dust shield
NeinrisThread starter‘Murica! · Mar 18, 2021#35
Originally Posted by enviri ↑
fill and redrill, find a machinist, mass produce. or make a hub spacer and screw the dust shield
That's partially what I have planned. I'm going to fill the holes and redrill. If the center of the hub don't poke through the back, I'm going to mill down the back of the plate just a bit so that the center of the hub would poke through even just a bit, 3mm should be enough, so the weight is not on the bolts. I might wait to do all of that until I'm back in Maryland though, my friend has a mill, drill press, etc. That's why I'm putting this on pause. I am going to go ahead and get the rest of the hardware from the junkyard this weekend though, I don't know when I'd get the opportunity again to find the whole set. I'll even grab the ebrake cables to make everything easier on me when it's finally time to install. I'll revive this thread once I've actually installed.
I don't know about mass producing, I might just give out the template dimensions for everyone to get their own made.
enviriCT · Mar 18, 2021#36
ever seen the old penguin garage hub spacers? you can just do that and add ears.
NeinrisThread starter‘Murica! · Mar 19, 2021#37
Originally Posted by enviri ↑
ever seen the old penguin garage hub spacers? you can just do that and add ears.
Never seen it. Got a link to share? Never mind, just saw the thread.

Would you mind measuring how long the round part is on the back of the hub? I don't feel like removing mine again. just wondering if it's longer than 11mm. I need to know if I need to do any milling. Thanks in advance.
NeinrisThread starter‘Murica! · Mar 19, 2021#38
Seeing that the Penguin spacers were 13 and 10mm thick, I won't bother milling the 11mm thick splash guard. I hope the bolts are strong enough. 😳
CrankyOldManWest Michigan · Mar 19, 2021#39
TL;DR - Use an SE axle. ;)

That's always a bummer when it doesn't pan out. Good on you for making the investigation though!
NeinrisThread starter‘Murica! · Mar 19, 2021#40
Originally Posted by CrankyOldMan ↑
TL;DR - Use an SE axle. ;)

That's always a bummer when it doesn't pan out. Good on you for making the investigation though!
Thanks. I just thought I'd share the idea. Like I said, I'll still continue with this project, just not right now, OR maybe an xB2 axle for 5 lug conversion? 😆 You'd definitely need a proportioning valve for the rear brakes if you don't have abs, the rear rotors for the xB2 are 279mm while the front are just 275mm!!!
enviriCT · Mar 19, 2021#41
SE rear rotors are 269mm. stock yaris front is 255mm. 275mm is the SE front. its far FARRR easier to do XD hubs for 5 lug. yeah i know xb2 is a different 5lug pattern.

btw, read Rear Drum to Disc Brake Conversion, pretty much the same discussion...but 2015..lol
NeinrisThread starter‘Murica! · Mar 19, 2021#42
Originally Posted by enviri ↑
SE rear rotors are 269mm. stock yaris front is 255mm. 275mm is the SE front. its far FARRR easier to do XD hubs for 5 lug. yeah i know xb2 is a different 5lug pattern.

btw, read Rear Drum to Disc Brake Conversion, pretty much the same discussion...but 2015..lol
Yup, I've seen that thread before. And I don't want 5X100, I'd go with 5X114.3 if I'm gonna go 5 lugs. Otherwise I would have already done it, there's a xD sitting in the junkyard where I go, which I'm going to grab the calipers and midpipe from. 😁 There are also a couple of xB2s, I might go take some measurements of the rear axle frame.

I'm not giving up on this project just yet though. You guys thinks that the bolts are strong enough to hold the weight on the back, or should I mill down the plate so that the center of the hub would poke through into the axle center hole?
enviriCT · Mar 20, 2021#43
why would you need to mill? anyway the abs sensor is 15-16mm. the bolts would handle it but i would still get longer grade 8 bolts
NeinrisThread starter‘Murica! · Mar 20, 2021#44
I feel like someone was out to sabotage my plans. The Scion xD that I was eyeing in the junkyard was moved to a different lot. OK, my fault for not checking the inventory. But not only was it moved to a different lot, it was moved to the “premium” section, so I had to pay an extra $2 to get in that lot. No big deal. But then the car was vandalized, the car was whole when I saw it last. This time the passenger steering knuckle was removed for no reason, luckily I found it between other cars in a completely different row. The brake lines were cut, and the mid pipe was hacked for no reason. Sigh...Good thing I hid the Corolla’s rear calipers, because when I got to that car the rear brake likes and cables were also tampered with.
Whatever, I still got the front xD calipers, and took the pads for free. Looks like the car had just gotten the brake pads replaced before it got junked.
NeinrisThread starter‘Murica! · Mar 20, 2021#45
Originally Posted by enviri ↑
why would you need to mill? anyway the abs sensor is 15-16mm. the bolts would handle it but i would still get longer grade 8 bolts
Thanks for measuring. My Yaris don’t have ABS. I think, I don’t know what to call it, the hub dowel? is shorter on non-ABS Yaris. If they are then I’d get the ones with ABS so it’d protrude out of the splash guard mounting bracket into the axle frame for the added weight support. Although, I just remembered that the Corolla’s hub dowel did not protrude out. I have the bolts that mounted the splash guard on the Corolla, they are longer than the Yaris’ bolts by at least 12mm I think. I forgot to take a pic to compare when I removed the hub. It has a washer on it, which I’ll remove.

1 attachment not included in this copy

NeinrisThread starter‘Murica! · Oct 18, 2022#46
The project is still on going… I just realized I need the hard lines for the rear:

1 attachment not included in this copy

NeinrisThread starter‘Murica! · Nov 7, 2022#47
My apologies this project has been dragging. 😳
I’ve bought most of the parts needed for this conversion. And I’ve just fitted a wheel hub and rotor. And they fit perfectly. Sorry I kept the rotor in its plastic packaging.
I’ll be going to my friend's house this weekend to do some machining to the caliper mounting plate. As you all can see in the first picture, the original mounting holes needs to be filled and re-drilled. I was hoping that the hub’s center bore pilot would protrude even just a little to support the weight, but unfortunately it doesn’t. So I’m debating if I should mil down the back of the plate’s mounting surface so that it would come out even just 2mm. I didn’t get a chance to measure it yet. I will see if I can this weekend.

2 attachments not included in this copy

06YarisRSFredericton, New Brunswick, Canada · Nov 8, 2022#48
Awesome! Will be following.
sh0rtlifepacific north WET · Nov 8, 2022#49
out of my own stupid curiosity...whouldnt the "XB" stuff work too?..seems more plentiful
NeinrisThread starter‘Murica! · Nov 9, 2022#50
Originally Posted by sh0rtlife ↑
out of my own stupid curiosity...whouldnt the "XB" stuff work too?..seems more plentiful
Which GEN xB would you be referring to? The 1st GEN has drum brakes on the rear. I don't know of any trim which has rear disc brakes, but I could be wrong. The 2nd GEN xB does have rear disc brakes, but the calipers mounts directly to the axle frame. If you can get a hold of a 2nd GEN xB rear axle frame, and see if it would fit the Yaris let me know, I'd switch to that and do a 5 lug conversion!!! I'd have to figure out if the front xB steering knuckles would fit in the Yaris. AFAIK, the drive axles have the same spline count towards the wheel hub.