ok bonus stupid question since the gen2 is part of the axle, are the gen1 xb drums bigger than the yaris?..just kinda thinking it may not be disc but may be a significant and cheep upgrade
Alternative rear disc conversion?
132 posts · 350,166 views · page 2 of 3
Replies continued
Both the Yaris and 1st GEN xB have 200mm nominal drum diameter. From RockAuto's parts diagram, the Yaris actually has an outer ring? for cooling I guess? The 1st GEN xB doesn't. I almost looked into getting a Honda Civic's rear drum, which has cooling fins (https://static.summitracing.com/glob...8736_RU_xl.jpg), the nominal drum size is also 200mm, but the outer diameter is too big, which I think won't fit in the drum back plate attached to the axle frame.Originally Posted by sh0rtlife ↑ok bonus stupid question since the gen2 is part of the axle, are the gen1 xb drums bigger than the yaris?..just kinda thinking it may not be disc but may be a significant and cheep upgrade
My friend made me weld the holes, so they’re no so great. We couldn’t find the chuck for his mill, so I haven’t been able to grind flush the welds down. I made sure the surfaces and holes were clean prior to welding.
2 attachments not included in this copy
The weld that filled the holes of the Corolla back plates are sooo tough. I bought a 8% cobalt drill bit set, and they still can’t penetrate through the welds. So I went with an alternative. Using the back plate from the Corolla, my friend made me a new back plate out of 1/4 inch steel plate. Here’s a preview of what will be, so stay tuned…
1 attachment not included in this copy
between your thread and my perpetual needing to re-adjust the drums..has got me re-thinking disc rears...
now hear me out...stock front yaris rotors put on the rear using XB rear calipers..i belive i could keep my 14inch aluminum wheels..the XB rear calipers solve the E-brake issue without the need for a drum hat rotor....tho i suspect id need an adapter mounting plate similar to yours but 1/4 inch of more offset in the rear of a stock yaris drum beam would square up the wheelbase nicely
now hear me out...stock front yaris rotors put on the rear using XB rear calipers..i belive i could keep my 14inch aluminum wheels..the XB rear calipers solve the E-brake issue without the need for a drum hat rotor....tho i suspect id need an adapter mounting plate similar to yours but 1/4 inch of more offset in the rear of a stock yaris drum beam would square up the wheelbase nicely
http://www.speedhunters.com/2019/04/...ng-conversion/Originally Posted by sh0rtlife ↑between your thread and my perpetual needing to re-adjust the drums..has got me re-thinking disc rears...
now hear me out...stock front yaris rotors put on the rear using XB rear calipers..i belive i could keep my 14inch aluminum wheels..the XB rear calipers solve the E-brake issue without the need for a drum hat rotor....tho i suspect id need an adapter mounting plate similar to yours but 1/4 inch of more offset in the rear of a stock yaris drum beam would square up the wheelbase nicely
Yet another amazing New Zealand build here but this one they show you how they modify there BB to increase track width by just attaching the same tabs as the brake caliper version had.
If you didn't know, the front wheels' track are wider than the rear by 10mm (5mm on each side), adding the 1/4 inch plate will make the rear 2mm wider than the front (1mm on each side).Originally Posted by sh0rtlife ↑between your thread and my perpetual needing to re-adjust the drums..has got me re-thinking disc rears...
now hear me out...stock front yaris rotors put on the rear using XB rear calipers..i belive i could keep my 14inch aluminum wheels..the XB rear calipers solve the E-brake issue without the need for a drum hat rotor....tho i suspect id need an adapter mounting plate similar to yours but 1/4 inch of more offset in the rear of a stock yaris drum beam would square up the wheelbase nicely
How would the xB's rear caliper mount on the rear axle frame? Or are you swapping out the axle frames?
Nice! But that rear disc conversion uses the drums for the parking brake. My conversion uses the discs as the parking brake.Originally Posted by Compeer ↑http://www.speedhunters.com/2019/04/...ng-conversion/
Yet another amazing New Zealand build here but this one they show you how they modify there BB to increase track width by just attaching the same tabs as the brake caliper version had.
I the end, here’s what mine will look like:
1 attachment not included in this copy
the issue i ran into when looking at the XA brakes..is the fact that they are all drum in the states but disc elsewhere in the world.....annoying at bestOriginally Posted by Neinris ↑If you didn't know, the front wheels' track are wider than the rear by 10mm (5mm on each side), adding the 1/4 inch plate will make the rear 2mm wider than the front (1mm on each side).
How would the xB's rear caliper mount on the rear axle frame? Or are you swapping out the axle frames?
and like you said the bonus is having the caliper be the hand brake and not have a set of drums under it and the second gen XB calipers are setup exactly like that and will sit over the yaris front rotors perfectly....the trick becomes mounting and i "think" there may be a solution to not using a spacer and just welding the caliper mount directly to the beam, its a question of how well the alignment sits for doing so
Once I get to mounted and tested for a few months I’ll let you know if there’s any mounting issue. I’m also planning on making another mounting plate for the Yaris SE caliper, which are clocked different than the Corolla calipers.Originally Posted by sh0rtlife ↑the issue i ran into when looking at the XA brakes..is the fact that they are all drum in the states but disc elsewhere in the world.....annoying at best
and like you said the bonus is having the caliper be the hand brake and not have a set of drums under it and the second gen XB calipers are setup exactly like that and will sit over the yaris front rotors perfectly....the trick becomes mounting and i "think" there may be a solution to not using a spacer and just welding the caliper mount directly to the beam, its a question of how well the alignment sits for doing so
your running the bigger rotors tho right?...i might be intrested in a set of plates from you even if i need to modify them slightyOriginally Posted by Neinris ↑Once I get to mounted and tested for a few months I’ll let you know if there’s any mounting issue. I’m also planning on making another mounting plate for the Yaris SE caliper, which are clocked different than the Corolla calipers.
im hell bent on keeping my 14 inch wheels....but finding a way to make a rear disc fit is looking really good right now...i have to re-adjust the rear drums every month
bonus is i allready have another set of front rotors sitting waiting
I do have the bigger rotors up front from the later model Yaris SE if that's what you're asking. I don't think they'll fit in 14" wheels, they barely fit in my 15" wheels.Originally Posted by sh0rtlife ↑your running the bigger rotors tho right?...i might be intrested in a set of plates from you even if i need to modify them slighty
im hell bent on keeping my 14 inch wheels....but finding a way to make a rear disc fit is looking really good right now...i have to re-adjust the rear drums every month
bonus is i allready have another set of front rotors sitting waiting
Seeing some's rear disc conversion like Compeer, who also has a set of 15" wheels, shows how close the caliper gets to the rear wheels. The stock front rotor size for none SE are 255mm, the rear rotors are 259mm. The rear calipers are smaller and seem to have a lower profile than the front calipers, so the rear disc conversion might still work for 14" wheels. If you don't have ABS, you'd have to get a brake balancer/proportioning valve for the rear line, since the rear disc will be bigger. Ditch using the front rotors for the rear, buy rear disc from RockAuto, I think they were $20 each when I bought mine.
curiosity why not use a set of fronts?..ive got matching set on the shelf drilled/slotted that i could use...and it seems to me if you had matching front/rear rotor size youd have less brake bias issues..sure youd still need the prop valve and to tweak it to perfection but there would be a whole lot less need to compensate with matched size on all 4...heck i bet you could balance it out some more by useing a "softer" pad in the back than the front
i can get full lock out of the fronts if i really REALLY get on it tho its useualy just 1 not both, so adding brakeing to the rear would be glorious..but im not losing my 14s...so im looking for a solve..and i think youve solved "most" of it
also looking at getting a toaster!..a gen1 xb and i know thats the same parts under it and 14's are most likely what will be on it as well...so if i can make this work on the yaris it would be the same parts on the xb
i can get full lock out of the fronts if i really REALLY get on it tho its useualy just 1 not both, so adding brakeing to the rear would be glorious..but im not losing my 14s...so im looking for a solve..and i think youve solved "most" of it
also looking at getting a toaster!..a gen1 xb and i know thats the same parts under it and 14's are most likely what will be on it as well...so if i can make this work on the yaris it would be the same parts on the xb
The calipers for the rear (with parking brakes) are made for solid rotors, not slotted, so they're really narrow. Not even the Supra rear calipers would work, their rear rotors are slotted, but only 16mm thick, the Yaris' front rotors are 22mm thick. So I'm curious, what caliper were you thinking of using that would work with the front rotors and has parking brake? Actually, I think I still have my old front rotors, when I get home today I'll see if they fit through the rear calipers slit and post a picture for you.Originally Posted by sh0rtlife ↑curiosity why not use a set of fronts?..ive got matching set on the shelf drilled/slotted that i could use...and it seems to me if you had matching front/rear rotor size youd have less brake bias issues..sure youd still need the prop valve and to tweak it to perfection but there would be a whole lot less need to compensate with matched size on all 4...heck i bet you could balance it out some more by useing a "softer" pad in the back than the front
i can get full lock out of the fronts if i really REALLY get on it tho its useualy just 1 not both, so adding brakeing to the rear would be glorious..but im not losing my 14s...so im looking for a solve..and i think youve solved "most" of it
also looking at getting a toaster!..a gen1 xb and i know thats the same parts under it and 14's are most likely what will be on it as well...so if i can make this work on the yaris it would be the same parts on the xb
i was eyeballing the second gen XB rear calipers with built in hand brake
Which xB, the 2nd GEN? Those rotors are bigger, 279mm, and only 10mm thick. The Yaris front rotors don't fit in the Corolla/Yaris rear caliper by the way. It's too thick. Sorry no pic, I just got home, and it's already dark outside. The MR-2 rear caliper might work for what you're trying to do, but you're modifying the parking brake cable to make it work.Originally Posted by sh0rtlife ↑i was eyeballing the second gen XB rear calipers with built in hand brake
oof yeah i didnt think about the thickness..tho your right the mr2 rear caliper looks serviceable
if i could find a "solid" rotor that was thin enough and similar DIA as the yaris fronts that would be ideal but im not sure such an animal exists in the 4x100...the alternative would be to get someone to "mill" down a set of the rears your using down to the same dia as the yaris fronts..but id really like it to be as "off the shelf" as possible
let me know what the max thickness a rolla calipers will fit ?...a bit of digging shows that a possible solution may be mazda miata mx5 rears 251x9mm thick correct center bore..its a question of offset and hub at that point
if i could find a "solid" rotor that was thin enough and similar DIA as the yaris fronts that would be ideal but im not sure such an animal exists in the 4x100...the alternative would be to get someone to "mill" down a set of the rears your using down to the same dia as the yaris fronts..but id really like it to be as "off the shelf" as possible
let me know what the max thickness a rolla calipers will fit ?...a bit of digging shows that a possible solution may be mazda miata mx5 rears 251x9mm thick correct center bore..its a question of offset and hub at that point
Like I said, the Yaris SE rotors are only 5mm bigger in diameter than the front. Maybe you can get away with using steel braided hoses upfront and regular rubber hoses in the rear to soften the brake pressure in the rear.Originally Posted by sh0rtlife ↑oof yeah i didnt think about the thickness..tho your right the mr2 rear caliper looks serviceable
if i could find a "solid" rotor that was thin enough and similar DIA as the yaris fronts that would be ideal but im not sure such an animal exists in the 4x100...the alternative would be to get someone to "mill" down a set of the rears your using down to the same dia as the yaris fronts..but id really like it to be as "off the shelf" as possible
let me know what the max thickness a rolla calipers will fit ?...a bit of digging shows that a possible solution may be mazda miata mx5 rears 251x9mm thick correct center bore..its a question of offset and hub at that point
5mm when your on 14s is ALOT lol when your talking about bigger calipers
i just made note than an 03 prius..uses 255mm rear rotors...prius rotors and calipers should clear, at that point its mounting them..and any weirdness with the hand brake cables
how are you handling the brake cables anyway
i just made note than an 03 prius..uses 255mm rear rotors...prius rotors and calipers should clear, at that point its mounting them..and any weirdness with the hand brake cables
how are you handling the brake cables anyway
I'm using the 2012 Yaris SE parking cables, they'll work with the Corolla calipers, that's one of the first thing I looked at before I envisioned the swap. With the exception of the hangers that they come with, they're pretty much a drop in. I'd have to route it differently than the Yaris though, because the mechanism for the Corolla pulls from the top. And the Corolla's calipers has to be clocked around 2 (driver side) and 10 (passenger side) O'clock to point the bleeder valve up. The Yaris' calipers are fine to be at 3 and 9 O'clock since the bleeder valve will already be pointing slightly upwards. See pics below, the shinny caliper is for the Yaris.Originally Posted by sh0rtlife ↑5mm when your on 14s is ALOT lol when your talking about bigger calipers
i just made note than an 03 prius..uses 255mm rear rotors...prius rotors and calipers should clear, at that point its mounting them..and any weirdness with the hand brake cables
how are you handling the brake cables anyway
2 attachments not included in this copy
I just realized I could run just one long rubber hose per side to the rear calipers instead of having multiple couplings. I’ll buy the Corolla rear brake lines and see if they’re long enough.
1 attachment not included in this copy
Just go to a brake shop and have hardlines made at that point and move the tabs at the same time, you would need to make propper mounts to hold the hose correctly may as well just get little hardlines made and move it, but personally I just went back to stock holes. Need to put my tein flex z back on soon, I want some 5mm spacers.Originally Posted by Neinris ↑I just realized I could run just one long rubber hose per side to the rear calipers instead of having multiple couplings. I’ll buy the Corolla rear brake lines and see if they’re long enough.
I actually have all the hardware I need to do the disc brake swap, minus the brackets for the hose lines. I wanted a different approach to reduce the coupling from hardline to rubber, to hard line again, then rubber to the caliper.Originally Posted by Compeer ↑Just go to a brake shop and have hardlines made at that point and move the tabs at the same time, you would need to make propper mounts to hold the hose correctly may as well just get little hardlines made and move it, but personally I just went back to stock holes. Need to put my tein flex z back on soon, I want some 5mm spacers.
1 attachment not included in this copy
ive got a shop local that i get custom braided lines from for CHEEP..so that would be my fix lol
My suggestion to you is to not go steel braided line in the rear, but the front, to soften the braking power in the rear since you’re hell bent on keeping your 14s.Originally Posted by sh0rtlife ↑ive got a shop local that i get custom braided lines from for CHEEP..so that would be my fix lol
Most likely, I’ll be installing my conversion next weekend. I think I know what I’m going to do with what I have.
when i flushed everything and put the drilled n slotted up front and new drums in the rear i put all braided lines on it because something was feeling "off"..turned out one of the lines was deteriorating on the inside..which is more common than you think....so ive allready got the braidsOriginally Posted by Neinris ↑My suggestion to you is to not go steel braided line in the rear, but the front, to soften the braking power in the rear since you’re hell bent on keeping your 14s.
Most likely, I’ll be installing my conversion next weekend. I think I know what I’m going to do with what I have.
i think at this point im more curious as to how the hand brake cables and your adapter go together
I hope this pic helps. I didn’t put the cable through the hole yet, because it’d be a bit of a challenge to remove. Now what is the concern again? Worried the cables will be too short? The mechanism pulls from the top, but it’s clocked closer to the parking brake cables. So I think they’d be just right.Originally Posted by sh0rtlife ↑when i flushed everything and put the drilled n slotted up front and new drums in the rear i put all braided lines on it because something was feeling "off"..turned out one of the lines was deteriorating on the inside..which is more common than you think....so ive allready got the braids
i think at this point im more curious as to how the hand brake cables and your adapter go together
Get the calipers meant for the Yaris, and the cable length will not be of any concern.
1 attachment not included in this copy
Hell yeah you have been shopping, this is going to be a sweet setup!Originally Posted by Neinris ↑I actually have all the hardware I need to do the disc brake swap, minus the brackets for the hose lines. I wanted a different approach to reduce the coupling from hardline to rubber, to hard line again, then rubber to the caliper.
Yeah little by little… I had to do my research first before I pulled the trigger. ��Originally Posted by Compeer ↑Hell yeah you have been shopping, this is going to be a sweet setup!
You guys taught me something, to not use a long one piece hose, unless it’s braided. But I think I’ll just stick with what I already have.
The bracket relocation is easy. I think I know what to do now, and hope to install next weekend. I need to use the drill press at work. ��
I went ahead and bought the Yaris calipers…. 😳
As I suspected, the caliper carrier’s bolt patterns are the same for the Corolla and Yaris. I went ahead and drilled the holes for the hub to clock the calipers at 3 and 9 o’clock. Don’t worry, if I reproduce them they won’t look like Swiss cheese… 😆
As I suspected, the caliper carrier’s bolt patterns are the same for the Corolla and Yaris. I went ahead and drilled the holes for the hub to clock the calipers at 3 and 9 o’clock. Don’t worry, if I reproduce them they won’t look like Swiss cheese… 😆
2 attachments not included in this copy
Yeah you can even bolt on twin pots from the BRZ levin, I was looking at some for sale. But my brakes are fucking fantastic now and i don't think I need it. Some people said the Bosch pads were not so great but these semi metalics are really nice feeling, Cofidence has gone up in the car again.Originally Posted by Neinris ↑I went ahead and bought the Yaris calipers…. 😳
As I suspected, the caliper carrier’s bolt patterns are the same for the Corolla and Yaris. I went ahead and drilled the holes for the hub to clock the calipers at 3 and 9 o’clock. Don’t worry, if I reproduce them they won’t look like Swiss cheese… 😆
The new brakes went from under 200% to almost 300% braking by mass on the brake testing machine when I got the last warrant and the pads had not worn in yet.
I can't wait for my disc conversion to get installed this weekend. Although I don't have ABS, I know my braking confidence will also increase.Originally Posted by Compeer ↑Yeah you can even bolt on twin pots from the BRZ levin, I was looking at some for sale. But my brakes are fucking fantastic now and i don't think I need it. Some people said the Bosch pads were not so great but these semi metalics are really nice feeling, Cofidence has gone up in the car again.
The new brakes went from under 200% to almost 300% braking by mass on the brake testing machine when I got the last warrant and the pads had not worn in yet.
I'm adding another project, my pursuit of 5 X 114.3 PCD...
good thinking on the dual clocking
brz twin pots on such a lil gokart would be down right insanity....you would have to be running atleast a 245 to be able to even use them!!!!
brz twin pots on such a lil gokart would be down right insanity....you would have to be running atleast a 245 to be able to even use them!!!!
The twin pots caliper are for the front though right?
The BRZ's front rotors are 326mm in diamenter!!! But they're 5X100 PCD.
The 2nd GEN Scion xB's front rotors are only 275mm in diameter compare to the BRZ/FRS, and they're 5x114.3 PCD. I wonder how far the BRZ's front calipers will stick out when mounted on the Yaris' steering knuckles? I hope not too far out for 275mm rotors...
You'd definitely would need to get at least 16in wheels for them to fit.
I'll keep this in the back of my mind... 😁
The BRZ's front rotors are 326mm in diamenter!!! But they're 5X100 PCD.
The 2nd GEN Scion xB's front rotors are only 275mm in diameter compare to the BRZ/FRS, and they're 5x114.3 PCD. I wonder how far the BRZ's front calipers will stick out when mounted on the Yaris' steering knuckles? I hope not too far out for 275mm rotors...
You'd definitely would need to get at least 16in wheels for them to fit.
I'll keep this in the back of my mind... 😁
its not about sticking out its about bolting them onto the correct mount to bring them down to the 275 rotor
I'm getting my threads mixed up... 😆Originally Posted by sh0rtlife ↑its not about sticking out its about bolting them onto the correct mount to bring them down to the 275 rotor
Well, that's what I kind of mean or need to know. How far will the caliper move out when it's mounted on a Yaris' steering knuckle? Will it be the same as the BRZ where you can house a 326mm rotor or will it be in like the Yaris SE/Corolla/xD? Or is there a different caliper carrier that it can be Frankenstein with and dial it for a 275mm rotor if you want to do a 5X114.3 PCD. Could I just make an adaptor plate and move out the xD calipers that I have to house 275mm rotors? But then the pads won't follow the same contour as the rotor. Would that really matter? 🤷
I've thought about using a 2nd GEN xBs steering knuckle, but looking at the holes, I don't think it'll mount to the Yaris' strut. You could probably use the xBs strut, but use the Yaris' top hat?
For the rear rotors, since it's solid, I could just mill down the xBs 279mm rotors down to 259mm, and still use the stock Yaris SE calipers. I don't think I can do that to the front rotors since they're finned. Or use the 279mm rotors, but will definitely need to install a proportioning valve, since the rear rotors are bigger.
I made the brackets out of aluminum angle, I couldn’t find anything else that’s 1/16in thick. Well at least I know they won’t corrode, and they’re strong enough that I can’t fold them by hand. I cheaped out and made my own retaining clips too… 😆
Once I position them on the axle frame, I’ll drill holes on the base and rivet them down. Yeah I know not welded, but it should still work.
I also made two extra ones with smaller hole, incase the hoses I’m relocating are differently designed than this hose. The hose in the pic is one that will connect to the caliper.
I don’t know why the first pic is upside down… 😳
Once I position them on the axle frame, I’ll drill holes on the base and rivet them down. Yeah I know not welded, but it should still work.
I also made two extra ones with smaller hole, incase the hoses I’m relocating are differently designed than this hose. The hose in the pic is one that will connect to the caliper.
I don’t know why the first pic is upside down… 😳
6 attachments not included in this copy
The clips atleast need to be the original hardened spring steel, Alu cannot work as a spring.Originally Posted by Neinris ↑I made the brackets out of aluminum angle, I couldn’t find anything else that’s 1/16in thick. Well at least I know they won’t corrode, and they’re strong enough that I can’t fold them by hand. I cheaped out and made my own retaining clips too… 😆
Once I position them on the axle frame, I’ll drill holes on the base and rivet them down. Yeah I know not welded, but it should still work.
I also made two extra ones with smaller hole, incase the hoses I’m relocating are differently designed than this hose. The hose in the pic is one that will connect to the caliper.
I don’t know why the first pic is upside down… 😳
exactly true, the aluminum is just going to let it go under pressure, or bend back n forth till it breaks off...it may not be "quick" but eventual inevitabilityOriginally Posted by Compeer ↑The clips atleast need to be the original hardened spring steel, Alu cannot work as a spring.
if you want "new" look for street rod hose mounts, if you want quick n dirty either cut some off a TRUCK/SUV...or even a car..tho on a car its hard to get enough materiel left to mount them
you can even look at clutch hose mounts, it only needs to fit the hose not the car, alot of the street rod ones are either studded for mounting or threaded for mounting so its easier to slap em in and be done
also aluminum on aluminum can and WILL corrode in fairly short order
Originally Posted by sh0rtlife ↑exactly true, the aluminum is just going to let it go under pressure, or bend back n forth till it breaks off...it may not be "quick" but eventual inevitability...
Are you talking about the clip or the mounting bracket? I agree, that the clips should be spring steel, after a few test of mounting the aluminum clips on and off, the didn't retain the bend. I just didn't want to pay the $8 per clip from Toyota. I'll see if the car parts store near me has anything similar.
If anything, the brackets will be temporary, I just want to slap the disc conversion ASAP.
You will have to repair the holes you drill tho, idk man this is your brakes, Do it once do it right.Originally Posted by Neinris ↑Are you talking about the clip or the mounting bracket? I agree, that the clips should be spring steel, after a few test of mounting the aluminum clips on and off, the didn't retain the bend. I just didn't want to pay the $8 per clip from Toyota. I'll see if the car parts store near me has anything similar.
If anything, the brackets will be temporary, I just want to slap the disc conversion ASAP.
The Alu bracket will brake as well not just the clip, the brake hoses move back and fourth when pressurized under braking, this is going to stress fracture then brake off the mount right where its bent. It would need a triangle welded in to stop this or for it to be a properly cast unit designed to not bend.
You can do the brake upgrade, just use the stock mount position for the trailing arm and stock brake brackets for now, Later on just move the brackets and change trailing arm position, changing the arms position only requires 10mins and a 17mm and extension and a jack.
Fine, fine… I’ve waited almost 2 years for this rear disc conversion, what’s another week of wait to do them properly. I’ll make the steel brackets at work this week and weld them next weekend.Originally Posted by Compeer ↑You will have to repair the holes you drill tho, idk man this is your brakes, Do it once do it right.
The Alu bracket will brake as well not just the clip, the brake hoses move back and fourth when pressurized under braking, this is going to stress fracture then brake off the mount right where its bent. It would need a triangle welded in to stop this or for it to be a properly cast unit designed to not bend.
You can do the brake upgrade, just use the stock mount position for the trailing arm and stock brake brackets for now, Later on just move the brackets and change trailing arm position, changing the arms position only requires 10mins and a 17mm and extension and a jack.
I painted my front calipers black, but I think I’ll paint them red along with the rear to make them look sportier. 😛
Hell yeah, and I know how you feel, I seen the RS crashed and wanted to do teh brake upgrade and then the car got dismantled. Took me 2 years to find another donor car to do my own swap.Originally Posted by Neinris ↑Fine, fine… I’ve waited almost 2 years for this rear disc conversion, what’s another week of wait to do them properly. I’ll make the steel brackets at work this week and weld them next weekend.
I painted my front calipers black, but I think I’ll paint them red along with the rear to make them look sportier. 😛
Its a minor upgrade for normal driving but if you live in the mountains or you drive aggressivly/take it to the track then this makes the car feels so much nicer. I had to do a hard stop yesterday on the motorway and she stopped on a dime, she will stop even better with the other suspension back in, just gotta bring myself to do another day out installing it all.
Have you ever thought of relocating the brake brackets that are hitting and move the trailing arms to the top mounting holes again?Originally Posted by Compeer ↑Hell yeah, and I know how you feel, I seen the RS crashed and wanted to do teh brake upgrade and then the car got dismantled. Took me 2 years to find another donor car to do my own swap.
Its a minor upgrade for normal driving but if you live in the mountains or you drive aggressivly/take it to the track then this makes the car feels so much nicer. I had to do a hard stop yesterday on the motorway and she stopped on a dime, she will stop even better with the other suspension back in, just gotta bring myself to do another day out installing it all.
I found some clippings of the stainless steel rails from work, they're 1/16 of an inch (about 1.6mm) thick, just what I'm looking for to make the brackets out of. I've made one bracket so far, while I'm on lunch break. 😳
Ok, I’ve made the brackets from steel. I drilled holes in the bottom where it’s going to mount so that the weld would hold better. Maybe a little over kill… 😳
I’m hoping that I can convince my friend to come to my house and bring his welder, instead of me coming to his house. It’s forecasted that there’d be freezing rain where he lives this Saturday, but not where I live, although it’s still going to be cold, but Sunday weather will be better. I might weld on Saturday and install everything on Sunday.
I’m hoping that I can convince my friend to come to my house and bring his welder, instead of me coming to his house. It’s forecasted that there’d be freezing rain where he lives this Saturday, but not where I live, although it’s still going to be cold, but Sunday weather will be better. I might weld on Saturday and install everything on Sunday.
1 attachment not included in this copy
Yeah but its very ilegal to do so, even moving the mount position is ilegal here.Originally Posted by Neinris ↑Have you ever thought of relocating the brake brackets that are hitting and move the trailing arms to the top mounting holes again?
I found some clippings of the stainless steel rails from work, they're 1/16 of an inch (about 1.6mm) thick, just what I'm looking for to make the brackets out of. I've made one bracket so far, while I'm on lunch break. 😳
I would need to get the brakes certed again because if the mechanic notices its "modified" it gets marked as modified and I have to get the entire cars brakes certed...NOT EASY.
Why arent you reusing the original brakets after cutting them off old position?
That sucks. You can't even just rotate them even just a little towards the inside so they won't hit the frame?Originally Posted by Compeer ↑Yeah but its very ilegal to do so, even moving the mount position is ilegal here.
I would need to get the brakes certed again because if the mechanic notices its "modified" it gets marked as modified and I have to get the entire cars brakes certed...NOT EASY.
Why arent you reusing the original brakets after cutting them off old position?
It's wasn't that hard to make the brackets, and it would be easier to just cut off the original ones that I need to relocate with a hacksaw than grind off the welds, and I don't have a grinding wheel. 😳
Besides, I need to make two additional brackets to weld near the rear wheel hub for the hose that goes to the calipers, remember those don't exist on the drum brake version.
My friend said he'd come here on Saturday, so it's game on this weekend!!!
This project is making me lose sleep... 😆
Last night, I was thinking too much about how or what I should be doing this weekend. I think I'll remove the axle frame from the car just to be safe, I don't any sparks near the gas tank, and I just filled up late last week. Not just that, also so I can get a good angle on the brackets I'm going to weld.
I'm going to buy an angle grinder, I found one for $50 USD, I'll try to remove the existing bracket that needs to be relocated and see if I can reuse them, also clean off the other spots where the other brackets are going to be welded down.
I'm debating if I should use the Yaris calipers or the Corolla calipers. It will depend on how the parking brake cable will be routed if the Corolla calipers are used. If you think about it, both the parking brake cable and brake line are on the top for the Corolla, which would make it easier to replace the brake pads, you just need to unbolt the bottom bolt and swing it up.
Last night, I was thinking too much about how or what I should be doing this weekend. I think I'll remove the axle frame from the car just to be safe, I don't any sparks near the gas tank, and I just filled up late last week. Not just that, also so I can get a good angle on the brackets I'm going to weld.
I'm going to buy an angle grinder, I found one for $50 USD, I'll try to remove the existing bracket that needs to be relocated and see if I can reuse them, also clean off the other spots where the other brackets are going to be welded down.
I'm debating if I should use the Yaris calipers or the Corolla calipers. It will depend on how the parking brake cable will be routed if the Corolla calipers are used. If you think about it, both the parking brake cable and brake line are on the top for the Corolla, which would make it easier to replace the brake pads, you just need to unbolt the bottom bolt and swing it up.
The Yaris brakes are pretty easy to do the brake job on, hardest part is twisting in the calipers (use a pair of needle nose pliers to twist them in)Originally Posted by Neinris ↑This project is making me lose sleep... 😆
Last night, I was thinking too much about how or what I should be doing this weekend. I think I'll remove the axle frame from the car just to be safe, I don't any sparks near the gas tank, and I just filled up late last week. Not just that, also so I can get a good angle on the brackets I'm going to weld.
I'm going to buy an angle grinder, I found one for $50 USD, I'll try to remove the existing bracket that needs to be relocated and see if I can reuse them, also clean off the other spots where the other brackets are going to be welded down.
I'm debating if I should use the Yaris calipers or the Corolla calipers. It will depend on how the parking brake cable will be routed if the Corolla calipers are used. If you think about it, both the parking brake cable and brake line are on the top for the Corolla, which would make it easier to replace the brake pads, you just need to unbolt the bottom bolt and swing it up.
I think Id go with the yaris set incase the caliper diameter is larger on the corolla calipers, No reason to mix and max brakes when you have the correct front and rear matching set which will give it the correct brake proportion.
I always go with "keep it simple stupid" and its a no brainer to install the matching front and rear brakes.