Yarisworld Archive

Alternative rear disc conversion?

132 posts · 350,166 views · page 3 of 3

Replies continued

NeinrisThread starter‘Murica! · Feb 23, 2023#101
Originally Posted by Compeer ↑
The Yaris brakes are pretty easy to do the brake job on, hardest part is twisting in the calipers (use a pair of needle nose pliers to twist them in)

I think Id go with the yaris set incase the caliper diameter is larger on the corolla calipers, No reason to mix and max brakes when you have the correct front and rear matching set which will give it the correct brake proportion.

I always go with "keep it simple stupid" and its a no brainer to install the matching front and rear brakes.
Remember, the adaptor plates were originally meant for the Corolla calipers, and I knew that the Yaris calipers would also works, because their rotors diameters are the same, therefore the caliper diameter are also the same. It's just that the Yaris' calipers are clocked directly to the rear (3 & 9 o'clock), while the Corolla's are clocked up (around 2 & 10 o'clock). And the Corolla's parking brake cable will be mounted on the top, farther away from the road and dirt. Less chance of seizing?

I thought of the same thing as you said, that's why I went ahead and bought the Yaris calipers, but I got to thinking how much convenient the Corolla's design is. I will show everyone what I mean how much easier it is to replace the brake pads when the Corolla calipers are used. Again, only if the route for the parking brake cables works out. We'll see this weekend.
CompeerAuckland, NZ · Feb 23, 2023#102
Originally Posted by Neinris ↑
Remember, the adaptor plates were originally meant for the Corolla calipers, and I knew that the Yaris calipers would also works, because their rotors diameters are the same, therefore the caliper diameter are also the same. It's just that the Yaris' calipers are clocked directly to the rear (3 & 9 o'clock), while the Corolla's are clocked up (around 2 & 10 o'clock). And the Corolla's parking brake cable will be mounted on the top, farther away from the road and dirt. Less chance of seizing?

I thought of the same thing as you said, that's why I went ahead and bought the Yaris calipers, but I got to thinking how much convenient the Corolla's design is. I will show everyone what I mean how much easier it is to replace the brake pads when the Corolla calipers are used. Again, only if the route for the parking brake cables works out. We'll see this weekend.
Yeah just go yari brakes they are oem the parts will fit, we know they work mint, will have hose connections at correct angles too and yeah the handbrakes..Keep it simple hahaha
NeinrisThread starter‘Murica! · Feb 24, 2023#103
Originally Posted by Compeer ↑
Yeah just go yari brakes they are oem the parts will fit, we know they work mint, will have hose connections at correct angles too and yeah the handbrakes..Keep it simple hahaha
Well, I’m really stubborn and likes going against the grain sometimes. 😁
I got home early from work today and started some of the work, but quickly ran out of daylight. 🙁
She’s dialed for the Corolla caliper, I’ll be testing how the cables will be routed tomorrow.
Picture not included in this copy
I hope it doesn’t snow tomorrow. Once I fit and test the parking cables then I’ll decide which calipers to use.
I did get to put one of the parking cable on, I had to swap two brackets from the old one.

4 attachments not included in this copy

CompeerAuckland, NZ · Feb 25, 2023#104
Weight them, they have the same caliper diameter and rotor which means the braking force is equal so weigh them and use the lighter set, we already lost some performance with the disc brake swap already especially considering they are pretty huge for the size of the car, don't want to loose more for no real reason. Im going to get a light weight 15" space saver spare tire and remove the rear seats and rear seat belts to try to make up for the added weight. Plan to put a plyboard bed in cut to shape with a hatch for the spare tire because Ineed to fit a set of wheels in for autocrossing eventually.

Builds looking good so far anyway, get her done!
NeinrisThread starter‘Murica! · Feb 25, 2023#105
Originally Posted by Compeer ↑
Weight them, they have the same caliper diameter and rotor which means the braking force is equal so weigh them and use the lighter set, we already lost some performance with the disc brake swap already especially considering they are pretty huge for the size of the car, don't want to loose more for no real reason. Im going to get a light weight 15" space saver spare tire and remove the rear seats and rear seat belts to try to make up for the added weight. Plan to put a plyboard bed in cut to shape with a hatch for the spare tire because Ineed to fit a set of wheels in for autocrossing eventually.

Builds looking good so far anyway, get her done!
The Yaris is very front heavy, so some weight in the back would help even it out. 😆

The parking brake cable routed just fine for the Corolla caliper, but I’m not decided yet to go with them.
Picture not included in this copy
I had some errands today, so I didn’t get to finish the install, but I did managed to remove the rear axle frame and install the parking brake cables. My friend didn’t show to weld the brackets, because the weather was too cold for him. 🙄
I have no choice but to finish tomorrow.

3 attachments not included in this copy

NeinrisThread starter‘Murica! · Feb 26, 2023#106
She’s finally done! I went with the Yaris calipers after all. I’m going to redo where the relocated brackets are, I think I’ll put on the center bar of the H, but that won’t be happening any time soon. My friend is going on a trip, and he left today with his welder. I should have said yes when he asked if I want to borrow it for a bit.
The stopping force comparison would not be fair if I’m comparing to the drum brakes, because I also replaced the front brake pads and changed out the brake fluid. All I’m going to say is I’m very happy with the results.
Here’s the before and after pics:

2 attachments not included in this copy

NeinrisThread starter‘Murica! · Feb 28, 2023#107
Originally Posted by sh0rtlife ↑
between your thread and my perpetual needing to re-adjust the drums..has got me re-thinking disc rears...

now hear me out...stock front yaris rotors put on the rear using XB rear calipers..i belive i could keep my 14inch aluminum wheels..the XB rear calipers solve the E-brake issue without the need for a drum hat rotor....tho i suspect id need an adapter mounting plate similar to yours but 1/4 inch of more offset in the rear of a stock yaris drum beam would square up the wheelbase nicely
What issues where you having that you had to re-adjust your drums often? Apparently my drum brakes would over tighten themselves over time, and was causing a bit more of a drag than normal. With the disc brakes, I noticed that I'm able to accelerate a little bit more quicker now, and my MPG has gone up from 31 to 31.5 in just two days!!! That's with my "normal" driving. 😁 We'll see how much better it'd get by the end of the week.
CompeerAuckland, NZ · Mar 1, 2023#108
Originally Posted by Neinris ↑
She’s finally done! I went with the Yaris calipers after all. I’m going to redo where the relocated brackets are, I think I’ll put on the center bar of the H, but that won’t be happening any time soon. My friend is going on a trip, and he left today with his welder. I should have said yes when he asked if I want to borrow it for a bit.
The stopping force comparison would not be fair if I’m comparing to the drum brakes, because I also replaced the front brake pads and changed out the brake fluid. All I’m going to say is I’m very happy with the results.
Here’s the before and after pics:
Looking good bro
NeinrisThread starter‘Murica! · Mar 1, 2023#109
Originally Posted by Compeer ↑
Looking good bro
Thanks Bro! I'm glad it's finally done. I was losing sleep a week prior because I kept thinking about the install. 😆

I think I'll share another guide how to do a disc conversion, to include PN from Toyota.

I think my friend is willing to produce the back plates for $75 USD if anyone's interested, plus shipping.
CompeerAuckland, NZ · Mar 2, 2023#110
Originally Posted by Neinris ↑
Thanks Bro! I'm glad it's finally done. I was losing sleep a week prior because I kept thinking about the install. 😆

I think I'll share another guide how to do a disc conversion, to include PN from Toyota.

I think my friend is willing to produce the back plates for $75 USD if anyone's interested, plus shipping.
Very nice result!
NeinrisThread starter‘Murica! · Mar 2, 2023#111
The rear wheels sticks out about even with the front now. I’ve yet to paint the front calipers red, or maybe I’ll paint the rear black like the front. Not sure which would look better.

2 attachments not included in this copy

NeinrisThread starter‘Murica! · Mar 5, 2023#112
I forgot to put into account that the drum brake back plates has some thickness to them, about 2mm. With the 1/4in plates (6.35mm), I’ve only added 4.35mm to each sides. The front are still .65mm wider at each side, 1.3mm wider total.
Picture not included in this copy
The back of the hub dowel?, I don’t know what to call it, protrudes about 8.15mm, about .5mm is taken by the splash guard, so there’s still at least 1.3mm inserted in the axle beam. So the weight are not all on the bolts.
Picture not included in this copy

2 attachments not included in this copy

remcafeeArizona · Mar 5, 2023#113
glad you finally got your rear discs done, never adjust and clean stupid drums ever again!
NeinrisThread starter‘Murica! · Mar 7, 2023#114
Originally Posted by remcafee ↑
glad you finally got your rear discs done, never adjust and clean stupid drums ever again!
Thanks remcafee… you were the first to reply to my thread 2 years ago almost to the day. I appreciate your inputs and assistance, along with everyone else.

Most have mentioned that these tiny cars don’t need rear disc brakes. That might be true, but it’d be so much more convenient to replace the brake pads now, and like you mentioned, no more adjusting and cleaning the stupid drums ever again!

The other factors I want to share are the fact that my fuel consumption has improved, not because the car is lighter now, but the fact that my drum brakes apparently overtightened themselves, which was causing some drag. Also, I’m no longer staying in 4th gear anticipating having to stop in my city driving.
I do have to get used to how quickly I stop now, before I was afraid of hitting the car in front of me, now I’m afraid of cars rear ending me… 😳
I’ve mentioned that I don’t have ABS, I've tested if my rear wheels would lock up first, but I couldn’t get the wheels to lock up at all, granted I was only going 45mph. I’ll try to test again some other time.

The other “alternative” that I want to present are the fact that the Prius and 2nd Gen Scion xB (xB2) has the same mounting holes bolt pattern like the Yaris. If I’m a betting man, the rear axle beam from those vehicles will fit in the Yaris. So they present as an alternate to the Yaris SE rear axle beam.
My new neighbor has an xB2, I’ll see if he’s willing that I’d take measurements and take pics. I’ll post pics here if or when I get the chance.
Next project is 5X114.3 PCD conversion. 😁

Oh, and I went ahead and painted the front calipers red. I took the brake pads off and put a bag over the rotors.

2 attachments not included in this copy

CompeerAuckland, NZ · Mar 7, 2023#115
Originally Posted by Neinris ↑
Thanks remcafee… you were the first to reply to my thread 2 years ago almost to the day. I appreciate your inputs and assistance, along with everyone else.

Most have mentioned that these tiny cars don’t need rear disc brakes. That might be true, but it’d be so much more convenient to replace the brake pads now, and like you mentioned, no more adjusting and cleaning the stupid drums ever again!

The other factors I want to share are the fact that my fuel consumption has improved, not because the car is lighter now, but the fact that my drum brakes apparently overtightened themselves, which was causing some drag. Also, I’m no longer staying in 4th gear anticipating having to stop in my city driving.
I do have to get used to how quickly I stop now, before I was afraid of hitting the car in front of me, now I’m afraid of cars rear ending me… 😳
I’ve mentioned that I don’t have ABS, I've tested if my rear wheels would lock up first, but I couldn’t get the wheels to lock up at all, granted I was only going 45mph. I’ll try to test again some other time.

The other “alternative” that I want to present are the fact that the Prius and 2nd Gen Scion xB (xB2) has the same mounting holes bolt pattern like the Yaris. If I’m a betting man, the rear axle beam from those vehicles will fit in the Yaris. So they present as an alternate to the Yaris SE rear axle beam.
My new neighbor has an xB2, I’ll see if he’s willing that I’d take measurements and take pics. I’ll post pics here if or when I get the chance.
Next project is 5X114.3 PCD conversion. 😁

Oh, and I went ahead and painted the front calipers red. I took the brake pads off and put a bag over the rotors.
Looks good, Ive been lazy and haven't painted mine yet...not sure what colour Id do other than red.
NeinrisThread starter‘Murica! · Mar 9, 2023#116
I was hoping to drop this comment yesterday to commemorate the two year start date of this project, but I got too busy.

Anyway, I know there's other threads out there that discusses what parts are required, etc., here's my version of what's required:

Rear disc conversion
Parts required:
Yaris SE parking brake cables (right) 4643052360 (left) 4642052370 [will require swapping hangers if not the same GEN Yaris]
Yaris SE rear axle beam 4210152160 or adaptor plates made
Yaris SE hard brake lines (right) 4732352110 (left) 4732452100
Brake hose retaining clips (2) 9046808035
Yaris SE brake hoses (2) 9094702E11
Brake dust shield (right) 4780352030 (left) 4780452030 [optional]
Yaris SE rear rotors (2) 4243152080
Toyota hub bearing mounting bolts (8) 90119A0350 [longer w/ washer (cut the washers out), not required if doing axle swap]
Yaris caliper carriers/bracket (2) 4782112151
Disc brake caliper pins (4) 4783512150
Bush dust boots (4) 4787512150
Caliper bracket mounting bolts (4) 91552C1035 [require washers if using adaptor plate vise axle swap]
Yaris Calipers (right) 4783052161 (left) 4785052161
Caliper mounting bolts (4) 90012AA102
Yaris SE rear brake pads (set) 0446652170
Yaris SE rear brake pads shim kit (set) 0494652080
Yaris SE rear brake pads anti-rattle clips (set) 0194812060
Toyota brake caliper banjo bolts (2) 90401A0001
Toyota caliper copper crush rings (4) 4738950020
Brake fluid of your choice
Note, these are all Toyota part numbers (according to parts.toyota.com), which are expensive. Aftermarket can be found for much cheaper and sometimes much complete where you don’t have to buy them piece by piece. I used a combination of RockAuto.com and EBay to get my parts. I was in no rush to get them, I did this over time when I have a little bit of money for myself, and so my pocket didn’t take too much toll.
Another option is you could go to the junkyard and pull them. If you’re looking for calipers in the junkyard, you could actually grab the 2nd GEN Scion xB’s (xB2) calipers, but use the Corolla rear caliper brackets, the xB2’s caliper brackets extends farther out to accommodate the 279mm diameter rotors, Yaris and Corolla rear rotors are only 259mm. The first pic right below shows the Corolla, xB2, and Yaris' calipers, then the Yaris's caliper over the xB2's caliper, to show that the bracket is extended out.
Picture not included in this copy
Picture not included in this copy
Also, I want to say that the Scion xB2 and Prius rear axle beam could probably be used as a replacement for the Yaris SE, but I'm not yet 100% sure at this point. I want to point out that the mounting hole bolt patterns are the same as the Yaris' rear wheel hubs.

If you’re not doing an axle swap, a couple of brackets must be made and welded on the axle beam for the rear most brake hoses that bolts to the calipers (sorry I don't have a picture of how I did this). What I did was mockup the locations by installing the hard lines first, then marked where the spots would be as close as possible to the stock locations. I believe that the brackets that I made are 1.5in (48mm) wide by 2in long (51mm), and 1/16in (1.6mm) thick with ¾in hole (19mm).
For the adaptor plates, I recommend using a ¼ inch or 6mm thick steel plates. The exact dimensions of the ones I used are 6 inch X 6 inch X ¼ inch, this is strong enough, and any thicker would make the center bore dowel not rest into the axle frame, which would make the bolts bear all the weight. In my previous post, I measured the center bore dowel at about 8.15mm. With the ¼ inch steel plate added with the thickness of the slash guard, the thickness is about 6.85mm, that leaves about 1.3mm of protrusion through the back, to rest in the axle beam's hole.
Picture not included in this copy

My previous calculations were wrong, when I said how much the rear track got wider, I forgot to include the splash guard, which are about .5mm thick. The original drum brake back plates were 2mm thick. So subtract that from 6.85mm, which means the rear got pushed out 4.85mm on each side, making the front still .3mm wider, not 1.3mm like I previously said. I could still be wrong, because I didn't really got to measure the splash guards. All I know is that the wheel hub's center bore dowels still has some protrusion, because they were not sliding off even without any of the bolts in yet.
Maybe when I replace the hubs to the 5X114.3 PCD, I'd hope to remember to take the measurements of the splash guards, then I'll see how much the rear track really got pushed out. Anyway that's another project... 😁

I used the Corolla’s rear hub mounting bolts, since they are longer and I got them from when I initially was going to use the Corolla’s adaptor plate, but they will require cutting out the washers.
Picture not included in this copy

To make the holes and bolt pattern on the adaptor plate, I had the Corolla back plate as a template, but one out of a cardboard can easily be made, I recommend something a bit thicker material.
Start with a 74mm hole, put your wheel hub in it and drill out the mounting holes, I believe they were 12mm if I remember correctly. I bought new wheels hubs, so I used them as a template, so I didn't have to remove the ones out of my Yaris. As you drill one out, put a bolt in it's place so that the hub don't move/swivel and get a more accurate pattern. Leave the hub in place, and fit the rotor. Now mock the caliper with the bracket and mark where the it would mount on to the plate. I don't remember the bolt hole size for the caliper bracket, I think 10mm. Then transfer that to the adaptor plate and Voila!!! Or send me a PM and you can have a pair for $75 plus shipping. 😳
I hope someone finds this useful.

4 attachments not included in this copy

sh0rtlifepacific north WET · Mar 13, 2023#117
so i found out something intresting

the XD uses the same rear beam as a yaris/prius but is 5x114, and...its drum
front suspension is all yaris..except the hubs..
i was digging thru toyotas own parts sheets, as i got a notice that theres an XD thats in a local yard....and its a "release" RS..and i wonder if the relese got a rear sway...same part as yaris btw

what im unsure of is if the XD drums are bigger than the yaris oe drums..other than being 5 lug

but what this tells me with 100% certanty is if you want to go 5lug the XD parts will get you there....shit i need to look at the front rotors and see if the cross referance to a rolla/camry/xb

even toyota DOES NOT cross referance the XB beam to anything but XB....but that could simply be the "tabs" and "ears" for disc brakes....as soon as its not a freak show of weather ill get you measurements off our patchwork xb-2

ROTOR ..rolla matrix XD...caliper rolla XD......
NeinrisThread starter‘Murica! · Mar 14, 2023#118
Originally Posted by sh0rtlife ↑
so i found out something intresting

the XD uses the same rear beam as a yaris/prius but is 5x114, and...its drum
front suspension is all yaris..except the hubs..
i was digging thru toyotas own parts sheets, as i got a notice that theres an XD thats in a local yard....and its a "release" RS..and i wonder if the relese got a rear sway...same part as yaris btw

what im unsure of is if the XD drums are bigger than the yaris oe drums..other than being 5 lug

but what this tells me with 100% certanty is if you want to go 5lug the XD parts will get you there....shit i need to look at the front rotors and see if the cross referance to a rolla/camry/xb

even toyota DOES NOT cross referance the XB beam to anything but XB....but that could simply be the "tabs" and "ears" for disc brakes....as soon as its not a freak show of weather ill get you measurements off our patchwork xb-2

ROTOR ..rolla matrix XD...caliper rolla XD......
We're getting mixed up with my other thread... 😆 Thanks for looking into this, but I already know that Yaris and xD shares the same suspension and that the rear beam from the xD will fit the Yaris, but which Prius are you referring to? Is it the Prius C with rear drum brakes or the regular Prius with rear disc brakes? The xDs have bigger rear drum brakes, ID is 229mm, Yaris is 200mm. I'm using xD front calipers for my bigger SE front rotors, I believe they're the same the Corolla's and maybe even the xB2 because they all the the same 275mm front rotors.
The xDs are 5X100 PCD and so are Corollas, I want 5X114.3 PCD like xB2 and Camry. So no, I'm not using the xD set up.
One of the members here, myfirstyota, did an engine swap and also swapped temporarily to the xD front knuckle. See the red car in first post (if you can see the pics, I can't for some reason see his posted pics when I'm at work, but I can see other people's posted pics).

The xd Swap thread
sh0rtlifepacific north WET · Apr 18, 2023#119
took measurements off the xb2 as i had time and right now im going to say that i think its too wide...i couldnt compare to the yaris but i could compare to the xb1 on the lift and its 5 inches wider at the lug pad....ill happly post the numbers later if you want

hell the springpockets are 6inches deep too!!!!..64ish wide
NeinrisThread starter‘Murica! · Apr 18, 2023#120
Originally Posted by sh0rtlife ↑
took measurements off the xb2 as i had time and right now im going to say that i think its too wide...i couldnt compare to the yaris but i could compare to the xb1 on the lift and its 5 inches wider at the lug pad....ill happly post the numbers later if you want

hell the springpockets are 6inches deep too!!!!..64ish wide
Yes please, post the measurements. I'd appreciate it very much.
Is the xB1's rear axle frame the same as the Yaris'?
Google says that xB2 rear track width is 59.8" and Yaris 57.5 - 57.9". xBs stock wheels and tires are 205/55R16 on 6.5 inch wide wheels, compare to Yaris 185/60R15 on 5.5 inch wide wheels.
sh0rtlifepacific north WET · Apr 18, 2023#121
Originally Posted by Neinris ↑
Yes please, post the measurements. I'd appreciate it very much.
Is the xB1's rear axle frame the same as the Yaris'?
Google says that xB2 rear track width is 59.8" and Yaris 57.5 - 57.9". xBs stock wheels and tires are 205/55R16 on 6.5 inch wide wheels, compare to Yaris 185/60R15 on 5.5 inch wide wheels.
ok so all of this is off of an 08 xb

these numbers are tricky as hell to get with the axle in place..so they are kinda rough and somewhat eyeballed

center of hub to top of caliper 6.5 +.5 hump at bleed screw
3 inch body mount bushing
centerline of body mount bolt to centerline of the hub 15
lugpad to lug pad 63.5(they seem to be fixing the track with wheel offset?)
spring pocket base to top of axle 5.5 inches deep
body mount bolt head to hub face centerline 8
outter edge of body mount to mount seems to be about 47..its hard to get exact with the fuel tank in

honestly im waiting to find a yaris and an xb in the same yard ...then i can pull em both set em next to eachother and see, hell i can even see if it bolts in.....we know the hubs do
NeinrisThread starter‘Murica! · Apr 19, 2023#122
Originally Posted by sh0rtlife ↑
ok so all of this is off of an 08 xb

these numbers are tricky as hell to get with the axle in place..so they are kinda rough and somewhat eyeballed

center of hub to top of caliper 6.5 +.5 hump at bleed screw
3 inch body mount bushing
centerline of body mount bolt to centerline of the hub 15
lugpad to lug pad 63.5(they seem to be fixing the track with wheel offset?)
spring pocket base to top of axle 5.5 inches deep
body mount bolt head to hub face centerline 8
outter edge of body mount to mount seems to be about 47..its hard to get exact with the fuel tank in

honestly im waiting to find a yaris and an xb in the same yard ...then i can pull em both set em next to eachother and see, hell i can even see if it bolts in.....we know the hubs do
Yeah, I think it's better to just compare them side by side.
sh0rtlifepacific north WET · Apr 20, 2023#123
Originally Posted by Neinris ↑
Yeah, I think it's better to just compare them side by side.
pretty sure they are..but...is a sedan and hatch the same beam?
what about the XA beam?
what about echo?

im asking specificaly as my most local yard has an 09 xb and an xa

and i know of another yard that "might" have 08 xb and a sedan..tho said sedan might be an echo?....

basicly trying to find alternative units that are the same unit to use as comparisons...since yaris, and xb dont seem to show up at the same time or be around long enough to overlap
NeinrisThread starter‘Murica! · Apr 21, 2023#124
Originally Posted by sh0rtlife ↑
pretty sure they are..but...is a sedan and hatch the same beam?
what about the XA beam?
what about echo?

im asking specificaly as my most local yard has an 09 xb and an xa

and i know of another yard that "might" have 08 xb and a sedan..tho said sedan might be an echo?....

basicly trying to find alternative units that are the same unit to use as comparisons...since yaris, and xb dont seem to show up at the same time or be around long enough to overlap
I'm not 100% about the xAs, I'll do some research. Do you see any xD? Those a the same as the Yaris.
sh0rtlifepacific north WET · Apr 22, 2023#125
Originally Posted by Neinris ↑
I'm not 100% about the xAs, I'll do some research. Do you see any xD? Those a the same as the Yaris.
i wish....theres one "forsale" in teh yard that they want WAY too much for that WILL end up in the yard...question is will the xb2 still be there when it does.....i want the mounts n stuff for the 1.8 swap
sh0rtlifepacific north WET · Apr 23, 2023#126
local yard has an XD and an XB1 hitting the yard soo...so if they hit while the XB2 is still in the yard i can compare those if we can verify that either of them is the same as a yaris

on a side note..since i had to pull a hub off the xb2 out there....i made a note, if someone wanted discs on a quick n dirty you could cut off the axle ends, grind em flush, get longer bolts, and just sandwich those plates into your existing axle tube..giving you 1/2inch offset and disc brakes all in one fell swoop....the hubs are just long to still locate thru the new flange and into the one still welded to your axle

now i need to find a 4x100 version to do some 14innch wheel clearance tests!!!!!!....prius's are NOT hitting my yards and i was unde rthe impression thats the only place to get the 4x100 factory discs(aside form a yaris RS which may as well not exist)
NeinrisThread starter‘Murica! · Apr 23, 2023#127
Originally Posted by sh0rtlife ↑
local yard has an XD and an XB1 hitting the yard soo...so if they hit while the XB2 is still in the yard i can compare those if we can verify that either of them is the same as a yaris

on a side note..since i had to pull a hub off the xb2 out there....i made a note, if someone wanted discs on a quick n dirty you could cut off the axle ends, grind em flush, get longer bolts, and just sandwich those plates into your existing axle tube..giving you 1/2inch offset and disc brakes all in one fell swoop....the hubs are just long to still locate thru the new flange and into the one still welded to your axle

now i need to find a 4x100 version to do some 14innch wheel clearance tests!!!!!!....prius's are NOT hitting my yards and i was unde rthe impression thats the only place to get the 4x100 factory discs(aside form a yaris RS which may as well not exist)
The mounting plates my friend made me is the quickest and dirtiest way for a rear disc conversion. LOL!!!
I'm sorry I could not find a 14" wheel to try and see if it'd fit, but I'm not sure that it'd be big enough. Unless the mounting holes for the caliper bracket are moved in closer to the center of the hub, probably 10mm??? But you might have to mill down the rear rotors as well to make them fit.
sh0rtlifepacific north WET · Apr 25, 2023#128
so for the axle comparison..are you 100% sure the xb1 axle is the same as a yaris...ive only eyeballed them but my eyes are telling me they are not the same...the xb1 actualy looks more "delicate" than the yaris unit

currently in the yard neer me is an xb1, xa, xb2, and an XD pending.....no yaris
NeinrisThread starter‘Murica! · Apr 28, 2023#129
Originally Posted by sh0rtlife ↑
so for the axle comparison..are you 100% sure the xb1 axle is the same as a yaris...ive only eyeballed them but my eyes are telling me they are not the same...the xb1 actualy looks more "delicate" than the yaris unit

currently in the yard neer me is an xb1, xa, xb2, and an XD pending.....no yaris
I was actually asking the same thing, if the xB1 is the same as the Yaris, but I know that the xD is the same as the Yaris.
sh0rtlifepacific north WET · Apr 29, 2023#130
Originally Posted by Neinris ↑
I was actually asking the same thing, if the xB1 is the same as the Yaris, but I know that the xD is the same as the Yaris.
theres 2 xd's "pending" they have been racked n drained..so i just hope they get out in the yard befor the xb2 goes

ive verifyed the XB1 is NOT the same as the yaris, after looking at the echo it "might" be the same as the echo, checked the XA and it looks to also be the xb1/echo style, but again the spring pockets were different

since i have an xb1 on the lift ive compared it to the yaris and can confirm its NOT the same, tho ive not checked the measurements, its visualy different both in how the unit looks but the spring pocket size and depth...

thats not to say it couldnt be a bolt in.....

next chance i get tho im going to get out to the yard and pull the XB2 axle and atleast stash it in the XB1...and i may see if it bolts up...

im currently checking the yard every couple days waiting on the XD's...i want all the engine swap bits!!!!

yes i currently own 07 yaris, 08 xb, 06 xb.....so im kinda lookin to see what tweaks i can do to the xb1 as well.....

something of note tho..the xb1 looks to have alot of built in rear camber...if someone were looking for camber that would be a way to get it if the arms swap
NeinrisThread starter‘Murica! · Apr 29, 2023#131
Originally Posted by sh0rtlife ↑
theres 2 xd's "pending" they have been racked n drained..so i just hope they get out in the yard befor the xb2 goes

ive verifyed the XB1 is NOT the same as the yaris, after looking at the echo it "might" be the same as the echo, checked the XA and it looks to also be the xb1/echo style, but again the spring pockets were different

since i have an xb1 on the lift ive compared it to the yaris and can confirm its NOT the same, tho ive not checked the measurements, its visualy different both in how the unit looks but the spring pocket size and depth...

thats not to say it couldnt be a bolt in.....

next chance i get tho im going to get out to the yard and pull the XB2 axle and atleast stash it in the XB1...and i may see if it bolts up...

im currently checking the yard every couple days waiting on the XD's...i want all the engine swap bits!!!!

yes i currently own 07 yaris, 08 xb, 06 xb.....so im kinda lookin to see what tweaks i can do to the xb1 as well.....

something of note tho..the xb1 looks to have alot of built in rear camber...if someone were looking for camber that would be a way to get it if the arms swap
Thanks for all the ongoing research. I really really appreciate it, and I'm sure others who would want to know about an alternative rear axle frame for a rear disc conversion.

Please continue the hard work.
NeinrisThread starter‘Murica! · Jun 18, 2024#132
Originally Posted by tayxas ↑
Hey Neinris, glad I found your thread. Are you willing to reproduce a set of those brackets? SE rear beams are rare and pricey. Would rather go this route.
Greetings Tayxas! My apologies I have not been active here for a bit. Other hobbies are taking over my time. I still have other plans for my Yaris.

Anyway, I'll ask my friend if he'd be willing to make another set if you're still interested.