Yarisworld Archive

The Lift Kit Thread aka The Canadian Commuter mod

215 posts · 194,883 views · page 1 of 5

myfirstyotaOriginal postToronto Canada · Feb 5, 2019#1
One day, I was driving down a snowy road in a lowered yaris. My old silver '07 3 door to be exact. As I could hear and feel the snow dragging on the floor pan I thought, am I gonna get stuck? How much extra fuel is this requiring? Is that massive ice chunk that fell off that truck gonna take out my bumper? Or worse a fuel line or something of the like? The answers that came to mind were maybe, a shit ton, and possibly, respectively. That's where it began... The idea of a fully bolt in suspension lift for our awesome little cars.

3 years later I got serious about it. My truck wasn't justifiable to continue to own. The cost of ownership versus the amount of use it got didn't add up. The thought of driving a lowered car through another winter made me cringe. The thought of swapping springs every 6 months bothered me. The idea of a yaris on stock suspension made me puke a lil in my mouth. So I started researching.

I found the Yaris Overlander. Black 3 door based out of B.C. Canada. Cool ride but, not a whole lot of info on the build itself. I found CTScotts crashy. Wild what that guy has done with that car. I researched donks (I know a donk is model and era specific vehicle but are generalized as lifted cars with huge wheels)

After soaking up all this, I came up with a plan. A front wheel drive donk/crashy inspired (coppied) front lift. Basically just 2 heavy gauge plates of steel with 2 sets of 2 holes drilled into them the same distance apart as the 2 bolts that hold the knuckle to the front strut. Exactly how crashy got its lift. Essentially lengthening the strut between the knuckle and where it mounts to the strut. I seen that many fwd donks are built this way and thought if Scott can plow with this setup, and donks run 28's on this setup.. it must be strong enough.

Ok, cool. Front is done. But what about the rear? Longer springs? Shocks to match? Off the shelf spring spacers? How will it ride? Will I be able to get the rake right(Stance)? How am I gonna find a longer shock that fits? I decided f_ck all that. I'm gonna use the stock springs and stock shocks just like the front. Rake will match factory, shocks will be easy to source, and if done right, could be completely bolt in.

So I went out to my scrap xD with my grinder and a cut off wheel. Zip, zip,zip and I'm holding 2 rear spring perches identical to the ones on the yaris axle. These are the key. These will allow you to retain your stock shocks because the lower shock mount is part of the spring perch.

This is where the measuring tape came out. A few quick measurements jotted down on a sketch pad and I was on my way to the metal place. $105cad and a waterjet cutting table and I have my pieces to fabricate my custom spring spacers.

The idea here is to fabricate a spacer that will sit in the factory spring perch and allow the donor xd perches to sit on top of them. Essentially pushing the lower spring perch up in relation to the rear axle. If the perch is mounted higher on the axle, the axle will sit further from the bottom of the spring giving you your lift.

Now pushing the axle down 3-4" will change the angle of the spring perch. To compensate this, I plan to cut the top of the spacer body on a bit of an angle. This should allow the xd perch to sit closer to the natural angle of the oem perch.

The oem perch has 8 holes in the base of it. I plan to drill 4 corresponding holes in the bottom flange of the spacer. That will be the 'bolt in' part. Pretty sure I'm just gonna weld the top xD perch to the top flange. No need to ever take that apart really.

I feel as though I may need to brace the shock mount on the upper xd perch as much of the strength was probably lost when I cut the perch from the axle. I don't see this being hard. Couple small pieces of metal bolted from the strong lower mount straight up to the weaker upper mount. I believe this is problem solved.

So my welding isn't the best, but I think it's gonna hold. I wanted to see what kind of angle the stock spring perch sits on so I can adjust the angle of the spacer to sit close to the factory spring perch angle...if you catch my drift.

Picture not included in this copy
Picture not included in this copy

Here is the properly mocked up spacer. Just gotta finish up the welds and drill 4 holes in the bottom flange.
Picture not included in this copyPicture not included in this copy

Here you can see how they sit in the factory spring perch.
Picture not included in this copy
Picture not included in this copy

This is the spacer with the spring perch and shock support all welded up. Remember now guys, this is a lift kit thread, not a welding-skills-flaming thread! In my defense you're only seeing pictures of the driver side. The passenger side was much prettier. I'm slowly getting better.
Picture not included in this copy
Picture not included in this copy

This is the spacer installed and lightly bolted in place. The washers were adjusted for the final tighten. The shock bolts I bought are a tad too short. No biggie. Swap them out for a longer version tomorrow.
Picture not included in this copy
Picture not included in this copy

There we are with the spring installed. No compressor needed but it may be a tight fit if you're limited with Jack height :)
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

Once you lower the car, what you're doing sets in.
Picture not included in this copy

Then I drove it up on a 4 inch brick on one side, and 3 inch assortment if wood on the other, just to see what it would look like
Picture not included in this copy

So,I've finally been able to almost complete the front lift. Just need find something to keep the upper bolts from collapsing the shock tabs when tightened. I'm just thinking stacked washers. Easiest and cheapest.
Picture not included in this copy

Disregard the clamp. It's just holding everything tight so you can get a better idea how it all works.

The only thing is, by doing the lift this way, you will need to grind/cut the bottom lip off the strut with an angle grinder/rotory tool for the 2 lift plates to sit parallel with each other. Other than this slight modification, both the front and rear lift are bolt-in.
Picture not included in this copy

Here you can see the oddly shaped upper spacer plates. They need to be cut like this to give you a flat-ish surface to mount the outter lift plates. The knuckle mounting tabs on oem shocks are stamped and have irregular shape assumingly for ridigity. If you have an aftermarket shock, these may not be needed. For example my bilstein shocks on my red car, have flat mounts.
Picture not included in this copy
Picture not included in this copy

In this pic you can see the assortment of spacer plates it takes to make this work with oem shocks. Notice the upper spacer plates are chamfered on the edges to clear the angles of the shock mount. You can also see some clearancing on the lift plates themselves.
Picture not included in this copy

Here you can see how the bottom spacer plates work
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

Replies 214

myfirstyotaThread starterToronto Canada · Feb 5, 2019#2
As mentioned in a recent post, the driveshaft won't clear the subframe when the wheels are pushed down almost 4". The passenger side hits the front control arm bolt. So the quest to lower the subframe begun. I fabricated these spacers from 2.5" square tubing with a 3/16" thick wall. The spacers were then boxed on one side for strength while allowing access to the bolts on the other.

Mocked up:
Picture not included in this copy

Welded up:
Picture not included in this copy

Primed, ready for paint:
Picture not included in this copy

Painted:
Picture not included in this copy

As you can see, my welding is getting better lol. However I can only lay about 3/4" of bead before my welder trips the breaker. Need that 240v plug!

The bottom holes of the spacers are large enough to accommodate a 1/2" drive extension. If you insert a socket inside the spacer and attach the extension through the bottom of the spacer, you have a practical way of tightening the bolts going into the body of the car.

Making space for the extension
Picture not included in this copy

Pictured below is one of the rear spacers. The holes had to be slightly offset to compensate for the angle in which the subframe mounted is on.
Picture not included in this copy

One of the problems with lowering the subframe is that your steering linkage must be lengenthened. Got a spare linkage from the u-pull and gave it the slice and dice.
Picture not included in this copy
Picture not included in this copy
The welded shaft was strong enough to dry steer the car down the driveway and around the corner but I'm gonna remove it and reinforce it. No point in taking chances here.

Another thing to mention is when the steering shaft is extended, it changes the angle it sits on. Clearancing of the body must be done for the u-joint of the shaft to clear the body.

Also, the steering shaft boot will no longer fit after being lengthened. Gonna have to figure that out still. Probably a larger boot from another vehicle.

So far, the clearancing of the body around the steering shaft and the bit of metal that must be removed from the bottom of the struts are the only things that may not make this kit "bolt-in" in some people's eyes
MaritimeWoodstock nb · Feb 6, 2019#3
Signing up, the reasons you mention are all the same reasons I am doing mine. Looking forward to see how yours turns out too.

Cheers

Maritime
MaritimeWoodstock nb · Feb 14, 2019#4
how tall are those BTW, looks like about 4" at least.
myfirstyotaThread starterToronto Canada · Feb 14, 2019#5
The body is 4" is diameter and I'm aiming for 3" to 3.5" tall body after the angles are cut. Once the flanges are added top and bottom, it should stand 3.5-4" total. I didn't abandon the project. Due so some unfortunate and fortunate circumstances, it's just on the back burner. Currently working out of town.
MaritimeWoodstock nb · Feb 14, 2019#6
Kool. No worries, life happens. Look forward to seeing it when you get time to finish.

Sent from my moto e5 play using Tapatalk
Tskm2Montreal · Mar 7, 2019#7
Post picture of cv joint when install! I have in same idea of lifting my 06. If you made spare parts or other give me new!
myfirstyotaThread starterToronto Canada · Mar 7, 2019#8
That's my only concern. The drivers side cv axle angle. We'll see how that plays out when I finish cutting the pieces for the front lift.

But sorry, no extra parts! Everything has to be made custom so I've only bought and cut what I need. But who knows, one day if I move away from the yaris platform, the kit may be for sale.

The weather is supposed to be warming up later this week and next so I imagine ill be able to get my drill press assembled and start drilling and cutting the pieces. Stay tuned!
MaritimeWoodstock nb · Mar 7, 2019#9
Originally Posted by myfirstyota ↑
That's my only concern. The passenger cv axle angle. We'll see how that plays out when I finish cutting the pieces for the front lift.

But sorry, no extra parts! Everything has to be made custom so I've only bought and cut what I need. But who knows, one day if I move away from the yaris platform, the kit may be for sale.

The weather is supposed to be warming up later this week and next so I imagine ill be able to get my drill press assembled and start drilling and cutting the pieces. Stay tuned!
Nice, yeah You may need a longer axle shaft but you can likely get an axle rebuilt with a longer shaft pretty cheap if there is a problem. I am hoping to get at mine this weekend as well. Bathroom reno is done and it's going to be warm enough to work with bare hands by sat afternoon.
myfirstyotaThread starterToronto Canada · Mar 7, 2019#10
Yep. Someone needs to stab old man winter in the face lol. I'm done!

I'm relying on the fact CTScott didn't have to extend any axles with his 4" front lift. I'm most worried about the angle of the shaft. I have a spare set from the swapped car. I will be carrying one on board with all tools needed (which isn't much suprisingly) to swap out in the event of a failure for the first few thousand km.
Tskm2Montreal · Mar 7, 2019#11
After a quick check. To put 4in in back pretty sure you need to move axle backside to recenter wheel in wheel well/arch. Like most 4wd rear independent suspension
myfirstyotaThread starterToronto Canada · Mar 8, 2019#12
I have scion xD springs in the car now. The oversize wheels I'm running now have less clearance to the rear bumper than they do to the front of the wheel well (body side). I actually had to remove the factory mud flaps to get the tires to fit, that's how close the tire is to the rear bumper. Im hoping that when the axle is pushed down, this will create more even spacing between the front and rear of the wheel arch. If not, I'd rather "make room" for the tires over relocating the rear axle. I think there's less chance of anything going wrong with axle alignment that way. Plus the car has over 300k on it and isnt "mint" by any stretch of the imagination lol. I have no qualms about cutting it up! Lol
MaritimeWoodstock nb · Mar 8, 2019#13
Originally Posted by myfirstyota ↑
I have scion xD springs in the car now. The oversize wheels I'm running now have less clearance to the rear bumper than they do to the front of the wheel well (body side). I actually had to remove the factory mud flaps to get the tires to fit, that's how close the tire is to the rear bumper. Im hoping that when the axle is pushed down, this will create more even spacing between the front and rear of the wheel arch. If not, I'd rather "make room" for the tires over relocating the rear axle. I think there's less chance of anything going wrong with axle alignment that way. Plus the car has over 300k on it and isnt "mint" by any stretch of the imagination lol. I have no qualms about cutting it up! Lol
I noticed this as well when playing around with the jacks and measuring clearances, the rear wheels sit more to the back of the well on the rear and when you lift they gain clearance and center more in the arch. I'm hoping to get my lifts in this weekend and test drive. If that goes well I am going to cover an existing wheel with stuff to make it the size of the new tires and check for clearance and compress suspension and steering etc. I also have no issues cutting some parts to make room. 360K and counting on the car.

looking forward to watching your progress.

Cheers,

Maritime
Tskm2Montreal · Mar 8, 2019#14
Post picture when install!
myfirstyotaThread starterToronto Canada · Mar 8, 2019#15
For sure!
myfirstyotaThread starterToronto Canada · Mar 10, 2019#16
Ok so I got a little cutting/drilling/welding done yesterday. I would have done more but I ran out of flux core wire for the MIG. Picked up some more last night though. It much warmer today although bit soggy. Gonna see if I can free up some space in the garage, do a lil more cutting n welding and possibly test fit one of the rear spacers. Pics to hopefully come later today....
myfirstyotaThread starterToronto Canada · Mar 10, 2019#17
So I went out to the garage to free up some space and of course... it decides to flood. So...Off to get some hardware for the bolt in part. Got some new contact tips for the MIG welder too. When I can get this done, it will be done.
myfirstyotaThread starterToronto Canada · Mar 15, 2019#18
Bump for new pics and progress
WeeYariGeorgetown, Ontario, Canada · Mar 15, 2019#19
Originally Posted by myfirstyota ↑
Bump for new pics and progress
Where?

Sent from my EML-L09 using Tapatalk
myfirstyotaThread starterToronto Canada · Mar 15, 2019#20
At the top. Post #2. The pics of the spacer with spring perch on top are new. So are the pics of the whole assembly sitting in the rear spring perch. Just need to finalize the welds and drill 4 holes and the driver side spacer is complete. Gonna attack the passenger side tomorrow but doubt I'll get it finished. Places to be around 2pm.
Tskm2Montreal · Mar 17, 2019#21
Nice building parts. Did you try placing coil in its place?
myfirstyotaThread starterToronto Canada · Mar 17, 2019#22
I only have access to the xd springs that are in the car now at the moment. No spring compressor needed to fit the xd coil in! And from what I remember, there was no height difference between the xd and yaris coil springs. Just that the material used to make the spring was thicker.
MaritimeWoodstock nb · Mar 18, 2019#23
those look slick. should work awesome. the XD is heavier so makes sense the coils would be thicker and you'd have less sag and why they give the lift at the same length as the stock springs. I assume you are going back to the stock Yaris springs to soften the ride? Looks great though. excited to see more.
myfirstyotaThread starterToronto Canada · Mar 18, 2019#24
I'm not sure if I'm gonna go back to the stock yaris springs in the rear. The xd springs are a bit harsher but that translates to decent cornering :) gonna have to experiment. For sure gonna put the oem yaris springs in the front though. I don't want over lift it up front and stress the cv joints.
MaritimeWoodstock nb · Mar 18, 2019#25
Cool. Looking forward to seeing it. I just drove An hour ar 120-130 kph and roof rack wasnt that bad. Must have put it just right LOL.

Sent from my moto e5 play using Tapatalk
myfirstyotaThread starterToronto Canada · Mar 18, 2019#26
Hopefully I'll get a chance this week to cut the other spacer and get everything welded up. Possibly drill all holes in the flanges this weekend and install with the xd springs just to see how it looks. Updates coming soon!
Tskm2Montreal · Mar 18, 2019#27
If you have stock spring in hand take measure of inside diameter top and bottom. I check after with jeep shop if something fit
myfirstyotaThread starterToronto Canada · Mar 18, 2019#28
In the 5th paragraph of the first post, you'll see the reason outlined as to why I didn't want to mess around with searching for spring and shock combinations that fit. The whole reason I'm building the spacers it to avoid all of that.
YarMateyCalgary, AB, CANADA · Mar 19, 2019#29
Definitely interested in seeing how this thread moves on!
I live in Calgary so the added ground clearance is something I’ve been toying with for a while now too. I’m familiar with Crashy and the Overland Yaris, however I found these pictures online which you guys might enjoy. Not entirely sure how he got the lift he did, I can’t find any info on this Yaris at all. I can see that he trimmed fenders and in turn removed the fender liners but from what I can see the suspension doesn’t appear aftermarket?

2 attachments not included in this copy

myfirstyotaThread starterToronto Canada · Mar 19, 2019#30
That's what I'm talking about! Appears he has taller springs in the rear. Although this is just speculation...
YarMateyCalgary, AB, CANADA · Mar 19, 2019#31
Yeah I’ve dug and dug and dug online to try to find info on that car somewhere but to no avail. Found one of the pics on Instagram but the person who posted wasn’t the owner sadly.
I’m guessing he’s got such an offset on the wheels to avoid any up front rubbing when turning?
It’s inspiring to see others getting funky with their Yaris as it means it’s definitely attainable!

Also, I noticed in your engine swap thread you were looking to add cruise control? Well CTScott did an awesome DIY write up with PDF instructions and all the part numbers you’d need depending on your year/style of Yaris. Should be pretty each to find through the search I think.
Tskm2Montreal · Mar 19, 2019#32
I read somewhere..on subculture maybe he's on stock suspension but he plan to custom made longer spring both front and rear.

Its sure any real suspension truck shop have a big book with all spec to find same spring rate but longer. In BC they have 2shop they made custom spring but the price...

Just need to find longer shock assembly and fit them like mazda3 owner put cx5 strut to lift 2-3inch
myfirstyotaThread starterToronto Canada · Mar 19, 2019#33
Originally Posted by Tskm2 ↑
I read somewhere..on subculture maybe he's on stock suspension but he plan to custom made longer spring both front and rear.

Its sure any real suspension truck shop have a big book with all spec to find same spring rate but longer. In BC they have 2shop they made custom spring but the price...

Just need to find longer shock assembly and fit them like mazda3 owner put cx5 strut to lift 2-3inch
When you find one that bolts in, let us know👍
myfirstyotaThread starterToronto Canada · Mar 19, 2019#34
Originally Posted by YarMatey ↑

Also, I noticed in your engine swap thread you were looking to add cruise control? Well CTScott did an awesome DIY write up with PDF instructions and all the part numbers you’d need depending on your year/style of Yaris. Should be pretty each to find through the search I think.
Yep. I've done it to 2 cars now. Love my cruise. I'm wondering if it's still a plug n play affair for the 2zr swapped car. I imagine it would be.... but can't confirm
YarMateyCalgary, AB, CANADA · Mar 19, 2019#35
Originally Posted by myfirstyota ↑
Yep. I've done it to 2 cars now. Love my cruise. I'm wondering if it's still a plug n play affair for the 2zr swapped car. I imagine it would be.... but can't confirm
An gotcha gotcha, makes sense. That’s one mod that I just haven’t gotten around to yet but hope to possibly sometime this summer! The cruise that is, not the engine swap haha. The xD’s seem pretty rare here so finding one to steal any goodies off of proves challenging.
MaritimeWoodstock nb · Mar 20, 2019#36
It doesn't look like the Black Yaris is lifted much at all. It looks like he put [s]spacers[/s] Wheels for offset and trimmed the fenders and that's it. If so I'll be fine doing what I am to mine as I'm not going that big on the tires. It's really neat looking though.
MaritimeWoodstock nb · Mar 20, 2019#39
Originally Posted by Tskm2 ↑
That's not the same car. that's the overlander. We all know that one already and the 1.5 lift is what I am doing after reading that article. The other one Yarmaty posted has Cali plates and different wheels and appears to have little to no lift on it.
YarMateyCalgary, AB, CANADA · Mar 20, 2019#40
I was thinking of doing a front suspension lift similar to what CTScott did with Crashy, just maybe utilizing plates with three holes in them so it’s not quite 4”. Then maybe just some slightly bigger springs in the rear, maybe from an xD to level it out.

Maritime, your don’t think the Cali Yaris has any lift on it all all? You think it’s all tire lift and he just trimmed fenders?
MaritimeWoodstock nb · Mar 20, 2019#41
When I look at the rear axle it looks like its in the same place as stock. He has major offset and trimmed arches so tire lift is all of the height at least to me.

Sent from my moto e5 play using Tapatalk
Tskm2Montreal · Mar 20, 2019#42
The second picture rear coil look bit to compressed maybe from the top spring...1.5in give the chance to put tire 3in diameter bigger and keep stock wheelgap at 27in tire that pretty nice
YarMateyCalgary, AB, CANADA · Mar 20, 2019#43
Yeah it’s very possible that it’s all tire lift I guess. I’m wondering if a guy could get away with less drastic of a wheel offset, without lift, and without rubbing issues up front.

Myfirstyota, do you by chance have any pictures of the front end lift plates that you fabricated up?
myfirstyotaThread starterToronto Canada · Mar 20, 2019#44
I actually just cut them today. I have yet to drill the 16 holes in the 4, 1/4" thick plates its gonna take to make these work. And there's still another 6 spacer plates with 2 holes each that need to be fabricated. However the spacer plates will be thinner metal so should be easier to drill.

I plan on fabricating the other rear spring spacer this weekend. If all goes well there, we could have a rear lift in by Sunday
myfirstyotaThread starterToronto Canada · Mar 20, 2019#45
I think the rear axle on the black California yaris pictured looks pushed down. If you look at the center of the wheel in comparison to the bottom of the body, it looks in line. Mine kinda sits above the bottom of the car, and I have way stiffer xd springs in mine.

Can anyone with stock springs with a hatchback chime in? Where does the center of your rear hub sit in relation to the bottom of the car?
myfirstyotaThread starterToronto Canada · Mar 20, 2019#46
Originally Posted by YarMatey ↑
I was thinking of doing a front suspension lift similar to what CTScott did with Crashy, just maybe utilizing plates with three holes in them so it’s not quite 4”
I also thought of this, but didn't want to regret not going high enough!! Hahah I'm aiming for 3&3/4" in the front with the 4 hole setup. I think that, plus whatever I can fit in tires, will make this car a monster. It already climbs snowbanks like an atv.
YarMateyCalgary, AB, CANADA · Mar 20, 2019#47
I have a 5dr hatch on stock springs and the rear hub is in line with the bottom of the rear bumper and maybe a couple inches above the bottom of the car body (between the front and rear wheels).

I mean I suppose I could always make a four hole set and if it’s too high just cut some off the end of each bracket and end up with a three hole set. Did you get a noticeable lift in the rear with just the xD springs prior to fabricating your spring mount towers?
YarMateyCalgary, AB, CANADA · Mar 20, 2019#48
Also, came across this on Instagram too. Guys brother made a killer custom roof rack for his Yaris and lifted it with what he said were 4Runner coils in the rear and strut mount extenders. Makes me wonder if just throwing some 4Runner springs back there is what he’s talking about?Picture not included in this copy
myfirstyotaThread starterToronto Canada · Mar 21, 2019#49
The lift on xd springs was noticible. When I lowered the car back onto the wheels it barely squatted. I'd say about an inch of lift. Although I went from lowering springs to the xd springs so I can't give an exact amount of lift.
myfirstyotaThread starterToronto Canada · Mar 21, 2019#50
Originally Posted by YarMatey ↑
Also, came across this on Instagram too. Guys brother made a killer custom roof rack for his Yaris and lifted it with what he said were 4Runner coils in the rear and strut mount extenders.
I can't help but think that would ride quite rough..