Yeah, 4 runners weigh a shit ton more than a yaris. Spring rate must be 4X or more. It would be like having no springs at all.
The Lift Kit Thread aka The Canadian Commuter mod
215 posts · 194,883 views · page 2 of 5
Replies continued
Yeah very fair points. I guess maybe a cruise to the junkyard with a tape measure or calipers might be in order to find some similar OD ones.
Definitely stoked to see some pictures of your Yaris Myfirstyota once you get all your fab work done and installed!!
Definitely stoked to see some pictures of your Yaris Myfirstyota once you get all your fab work done and installed!!
Still aiming for the rears to be complete this weekend! Pics soon!
Yay, good luck. I also hope to get my whole lift in. I have to start with the rears and check fitment of the unbranded lifts I bought off amazon. May need to mod those, if they need modding, it won't get done, if they fit. I'll have her all lifted this weekend. I only have about a 2-3 hour window of time and being my DD I need to get it all done in that time or wait.
Picture not included in this copy
New pics on first page!
New pics on first page!
Hahaha awesome. That look perfect with that tire size.
Did you cut the front only for stock heigh whit this tire?
Did you cut the front only for stock heigh whit this tire?
I cut the front bumper cause of body damage originally.. I hit a hiway caution barrel that was overturned with its base toward traffic somewhere between Kingston and the 416 to Ottawa. There were no reflectors to be seen. I cut the fractured section of the front bumper off and cut the other side to match, knowing it would add to my off road look. I will mention agan I'm running scion xD front fender liners. They "kinda" fit but are a bit more roomy than the yaris ones.
I'm expecting major trimming for the larger tires.
Also, I'd like to run some pretty wide spacers or very offset wheels. And probably fender flares to keep the cops at bay :)
Also it seems there may be some leverage factor to my lift as it looks taller than I thought it would. The spring is located close to the fulcrum of the axle, being the mounting points. The wheel being further down the arm may generate more lift at the end?
Anyone with a 3 or 4 door hatch on stock springs wanna measure from ground to the jack points for me? At no point was i under 12" to mine!
I'm expecting major trimming for the larger tires.
Also, I'd like to run some pretty wide spacers or very offset wheels. And probably fender flares to keep the cops at bay :)
Also it seems there may be some leverage factor to my lift as it looks taller than I thought it would. The spring is located close to the fulcrum of the axle, being the mounting points. The wheel being further down the arm may generate more lift at the end?
Anyone with a 3 or 4 door hatch on stock springs wanna measure from ground to the jack points for me? At no point was i under 12" to mine!
150 successful km so far. Hiway speeds of 120+km/h. Drives fine though I'd be weary of high speed lane changes for emergency purposes. Its not short anymore. Hoping the front lift and spacer or rim offset corrects it a bit.
Picture not included in this copy
Picture not included in this copy
That’s a hefty lift going on there! Some trimming and bigger tires will look awesome on it.
My 4 door hatch measures at 8” ground to jack point at the rear pinch weld and 7.5” ground to jack point at the front pinch weld. Stock springs, 185/65r15 tires.
My 4 door hatch measures at 8” ground to jack point at the rear pinch weld and 7.5” ground to jack point at the front pinch weld. Stock springs, 185/65r15 tires.
I believe the stock 14" tire size is on the left. 175/65/14.
On the right is my hopeful tire size. 215/75/15.
Picture not included in this copy
On the right is my hopeful tire size. 215/75/15.
Picture not included in this copy
Yeah and stock for 15’s is 185/60r15, I’m running a bit of an oversized tire since I got a smokin’ deal on some blizzaks off kijiji.
Have you decided on which tire you’re going to go with? I know a lot of people like the General Grabber AT2s, and I believe they come in a 205/75r15 which is only a 27.1” diameter. I wish BFG still made their super small All Terrain TA KO’s.
Have you decided on which tire you’re going to go with? I know a lot of people like the General Grabber AT2s, and I believe they come in a 205/75r15 which is only a 27.1” diameter. I wish BFG still made their super small All Terrain TA KO’s.
So you're riding 3/4" higher than a base model cause your wheels are bigger. Need to subtract that from your Jack point height to get a better height estimation
Pretty sure the k02's come in the 215/75/15 size.
Pretty sure the k02's come in the 215/75/15 size.
Yeah they do, they used to make a 195/75r14 for them though. I believe there’s an off-road/dirt Yaris thread on here somewhere and he has them on his Yaris.
I had the 175/65r14s on before the 185/65r15s and noticed that 3/4” for sure once I put them on.
I had the 175/65r14s on before the 185/65r15s and noticed that 3/4” for sure once I put them on.
Would be good for those not wanting to cut up their car! LolOriginally Posted by YarMatey ↑Yeah they do, they used to make a 195/75r14 for them though. I believe there’s an off-road/dirt Yaris thread on here somewhere and he has them on his Yaris.
Update: Approx. 4-500km on the rear lift. All is quiet and the cars ass is still in the air. The spacers look to be a success!
Sweet. mine has a bit of a clunk with the lifts I put in and I wonder if my shocks are topping out sometimes. May need to put extenders on those. you built that right into the lifts. It's a bit weird driving with just the ass up isn't it.
Too bad these don't exist anymore. That's why I'm going with the Grabbers in the 27x8.5R14. Which I may be ordering next week if my re-engineered front lifts work out this weekend.Originally Posted by myfirstyota ↑Would be good for those not wanting to cut up their car! Lol
Yea, it's substantial. I felt the angle of the seats changed drastically when it was done. Gets a ton of looks too lolOriginally Posted by Maritime ↑It's a bit weird driving with just the ass up isn't it.
You may need to make substantial clearance for that size. For the 27.7" tires I plan to run, gonna need to cut/bend a good portion of rear fender well out of the way, and I'm much more lifted than you are.Originally Posted by Maritime ↑Too bad these don't exist anymore. That's why I'm going with the Grabbers in the 27x8.5R14. Which I may be ordering next week if my re-engineered front lifts work out this weekend.
I expect some trimming and need to pull the fender liners
Sent from my moto e5 play using Tapatalk
Sent from my moto e5 play using Tapatalk
We still gotta figure out the fender flare situation lol
Originally Posted by myfirstyota ↑We still gotta figure out the fender flare situation lol
I found some that are flexible in shape. Like a roll you trim off what you need and attach it to the fender and it conforms to the shape. I'll try and find the link. not sure I saved it.
Did a mock up, I scaled the 2 in the pic until the small was the same as the old tire so this is close to what the new tires will be like!
1 attachment not included in this copy
These are the flare I was thinking may be good as they follow however you cut.
https://www.amazon.ca/dp/B0794BXHSQ/...4-339eef22020c
https://www.amazon.ca/dp/B0794BXHSQ/...4-339eef22020c
1 attachment not included in this copy
Oh wow... I hope that's not the case!Originally Posted by Maritime ↑Did a mock up, I scaled the 2 in the pic until the small was the same as the old tire so this is close to what the new tires will be like!
I'd be worried about structural damage cutting that much!
Paint isnt perfect fir sure. I bet it wont be that drastic
You guys will be able to get away with much more rear wheel cutting than us four door hatch drivers. We’d have to end up cutting into the doors haha.
I know that in place of all terrains some Subaru guys run chunky winter tires such as the Firestone Winterforces. They have a relatively aggressive look to them and would be available in sizes smaller than the 27” grabbers.
I know that in place of all terrains some Subaru guys run chunky winter tires such as the Firestone Winterforces. They have a relatively aggressive look to them and would be available in sizes smaller than the 27” grabbers.
I'm a 4 door LOL. I've owned grabbers and like the low noise but the AT tread, a lot of the beefy winters are noisey as hell and soft so in summer they melt off the car.Originally Posted by YarMatey ↑You guys will be able to get away with much more rear wheel cutting than us four door hatch drivers. We’d have to end up cutting into the doors haha.
I know that in place of all terrains some Subaru guys run chunky winter tires such as the Firestone Winterforces. They have a relatively aggressive look to them and would be available in sizes smaller than the 27” grabbers.
What a beast, she'll be! Pumped to see the final effect. 👍Originally Posted by Maritime ↑Did a mock up, I scaled the 2 in the pic until the small was the same as the old tire so this is close to what the new tires will be like!
Still lots of steel to grind out on the front lift. It'll happen soon lol
Update?
The rear spacers are holding beautifully. Probably 7-9000 km and everything seems great.
Im about half way done the front. I had to buy an electric die grinder. I settled on a rotozip. Was about half the price of an electric die grinder with variable speed. Its basically a dremel but 4 times the size and power. Hopefully can handle the job unlike the mastercraft rotory tool. Im hoping in the next 2 weeks ill be ready to install the front lift. Ive been working out of town and thats been slowing progress down.
Im about half way done the front. I had to buy an electric die grinder. I settled on a rotozip. Was about half the price of an electric die grinder with variable speed. Its basically a dremel but 4 times the size and power. Hopefully can handle the job unlike the mastercraft rotory tool. Im hoping in the next 2 weeks ill be ready to install the front lift. Ive been working out of town and thats been slowing progress down.
Originally Posted by myfirstyota ↑Anyone with a 3 or 4 door hatch on stock springs wanna measure from ground to the jack points for me? At no point was i under 12" to mine!
Stock springs all around, with the Firestone airbag helpers in the rear. Tires are 195/75-14s.Originally Posted by YarMatey ↑My 4 door hatch measures at 8” ground to jack point at the rear pinch weld and 7.5” ground to jack point at the front pinch weld. Stock springs, 185/65r15 tires.
ground to pinch weld. Front: 8.25" and rear: 8.75"
Yes. I still have them on the Yaris. If shipping and import fees weren't so crazy to get them to Canada, I'd sell 'em to one of you guys.Originally Posted by YarMatey ↑Yeah they do, they used to make a 195/75r14 for them though. I believe there’s an off-road/dirt Yaris thread on here somewhere and he has them on his Yaris.
If I were to stay with a 25" or so tire, I'd look into rally tires. Still haven't found a "regular" all terrain type tire. Then again, do an eBay search for all terrain 195/75-r14, and you'll see some pop up.
I'd personally stay with 14" wheels in order to keep the weight down a bit. Maxxis Tires have both a mud terrain (Buckshot Mudder) and all terrain (Bighorn MT-762) at a 27x8.5-14 size. Though the specs list them at 26.6" and 26.3", respectively.
Stock springs. Tokico reds. BFG All Terrains. 0195/75-14
Just to give you guys an idea to the clearance around the tire
Picture not included in this copy
Just to give you guys an idea to the clearance around the tire
Picture not included in this copy
Hey, how much to ship to 04730 ME? Id be interested.Originally Posted by justjesus ↑Stock springs. Tokico reds. BFG All Terrains. 0195/75-14
Just to give you guys an idea to the clearance around the tire
Picture not included in this copy
Sent from my moto e5 play using Tapatalk
Updates! Post #2
Those look good. I thought about something like that but didn't need that much height so went from the top. May re-think it after I see yours installed.
Thanks! I'm not a machinist by any means. And it isn't easy to drill large holes in 1/4" flat stock perfectly spaced and aligned without a large drill press. I ended up drilling smaller holes and ground them out with a carbide burr on a rotozip. All in all, there was 4 lift plates (long ones on the ends), 12 spacer plates to make, and 40 holes to drill and grind out. I'll report back when it's all installed. Honestly not sure when that is. Back out of town tomorrow for work.
Understood. I make do like that too. We look forward to the progress however slow it has to be. Im no better. My other crap keeps breaking down and taking my shop time.
Sent from my moto e5 play using Tapatalk
Sent from my moto e5 play using Tapatalk
Amen!Originally Posted by Maritime ↑My other crap keeps breaking down and taking my shop time.
Got two quotes. Not looking good.Originally Posted by Maritime ↑Hey, how much to ship to 04730 ME? Id be interested.
First one was $83.49 each (about 334 for 4)
Second one was $354 total for 4.
I do have a 5th tire, new as well, so that's additional shipping charge 🙁
Yes, that was just the tires. The weight of the wheels was not included in those quotes! And those are just the shipping costs. 😳
At this time, it might be better/ cost effective to get some new tires. Maybe those 27s and make them work with a small lift.
Thanks for looking, yep I can get the 4 27's for 600 installed and balanced so no savings on yours. Too bad I like the bfgs a little better than the grabbers.
Sent from my moto e5 play using Tapatalk
Sent from my moto e5 play using Tapatalk
That's pretty good price.
These are the prior gen KO2s (or KOs?). I have the Grabbers on my Jeep and they look very similar. Biggest difference is on the side knobs.
I'm liking both okay, but would prefer the newer tires with the beefier sides :)
These are the prior gen KO2s (or KOs?). I have the Grabbers on my Jeep and they look very similar. Biggest difference is on the side knobs.
I'm liking both okay, but would prefer the newer tires with the beefier sides :)
Yep. I ran grabbers on an XTrail and liked them enough but found the bfgs a little better on the toyota I had those on
Sent from my moto e5 play using Tapatalk
Sent from my moto e5 play using Tapatalk
Good to know! ThanksOriginally Posted by Maritime ↑Yep. I ran grabbers on an XTrail and liked them enough but found the bfgs a little better on the toyota I had those on
Sent from my moto e5 play using Tapatalk
Update. Ill be pulling the rear spacers out hopefully this weekend. To clean them up, Inspect, paint and rustproof.
Also some more eye candy in post 2
Also some more eye candy in post 2
Awesome work. Thats fit perfect!
Looks like you’re definitely taking the time to do some quality work with the modifications! Can’t wait to see picture of the Yaris all lifted up and rolling!
I’ve searched high and low for used xD suspension for a bit of lift with no luck, stealership wants ~$900cad for strut assemblies and shocks unfortunately.
I’ve searched high and low for used xD suspension for a bit of lift with no luck, stealership wants ~$900cad for strut assemblies and shocks unfortunately.
Try a fully assembled Munroe unit from partsource or something. May be cheaper. It's a good option for the front. I never looked into it personally. But worth a shot. And you'll get new shocks that way too.Originally Posted by YarMatey ↑Looks like you’re definitely taking the time to do some quality work with the modifications! Can’t wait to see picture of the Yaris all lifted up and rolling!
I’ve searched high and low for used xD suspension for a bit of lift with no luck, stealership wants ~$900cad for strut assemblies and shocks unfortunately.
Yeah I looked into those briefly, I can’t find anyone that sells the springs for the rear aside from Toyota/Scion.