Yarisworld Archive

DIY: OEM JDM HID Headlight Conversion

119 posts · 72,881 views · page 3 of 3

Replies continued

GPBIGPuerto Rico · Mar 7, 2019#101
Originally Posted by enviri ↑
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

I conect everething like you said, hi beam work , but no HID . Is save to test the HID ballast with only a positive and negative to the battery?
BIGTAZ351North Branch, MN · Apr 12, 2019#102
Interesting Thread....I do not believe my 2010 3D Hatch is Negative Switched...I purchased "Headlight Revolution" H4 LED Headlights and plug and play installed normally last summer... After buying some "No Name" LEDs that also worked normally but had crappy output...Maybe they got rid of that with the DRL?
IllusionXBrossard, QC · Apr 12, 2019#103
Originally Posted by BIGTAZ351 ↑
Interesting Thread....I do not believe my 2010 3D Hatch is Negative Switched...I purchased "Headlight Revolution" H4 LED Headlights and plug and play installed normally last summer... After buying some "No Name" LEDs that also worked normally but had crappy output...Maybe they got rid of that with the DRL?
The cheapest LED headlights bulbs have auto sensing polarity. You can connect whichever way you want it will always work.

Sent from my CLT-L04 using Tapatalk
BIGTAZ351North Branch, MN · Apr 12, 2019#104
I will have to check that...Because I also had installed a H4 relay harness when I was running the 100W/130W Halogens (Which I removed when I went to LED) and it worked normally as well...and it was installed into my Chevrolet after the Yaris...and I thought I checked the outputs before I installed that harness...I seriously do not think the newer NON-DRL ones are Negative switched.

(And those H4 were from the motorcycle world, they do not work backwards!)
ezhacker1San Francisco · Apr 13, 2019#105
this should help. Power flows as same way no matter if its ground or positive switched. But yes Yaris are ground switched 06-11 for sure.

1 attachment not included in this copy

BIGTAZ351North Branch, MN · Apr 15, 2019#106
OK I went out and tested my car...It does feed Backwards...I am curious how the Relays in the HD wiring harness allowed it to work, those relays have a diode in the trigger coil to prevent back feeding? And because I purchased it for a "Normal" vehicle then used it on a "Backwards" vehicle, then installed it on a Normal Vehicle...either those relays work both ways and or the diodes were non-existent... Either Way seems the LED lights have gotten "smarter" than when they first started making them for Motorcycles...they wouldn't work or would "smoke" if you gave them power thru the Ground! (Very Interesting)

(The power actually flows Backwards thru the bulb, This is DC not AC.)
DeeBeeAustralia · Aug 24, 2019#107
Originally Posted by DeeBee ↑
Finally, I have success!!

The low beam stays on when I select the high beam 🎉

I used a 6A 400V rectifier diode between the low and high beam ground wires connected to the low and high beam relays.

So far the result is what I have been looking for 👍

Thank you all for your help along the way!!!
This was short-lived😠

My HID's started flickering intermittently😕

After some investigation I found that the harness I used had started melting connectors 👎 Not sure if the diode "fix" was responsible but I was lucky my headlights did not shut off on me while driving on a dark road or highway.

I had to disconnect everything and I'l have to do this install all over again in the summer! I think this time I'll look for one of the Morimoto harnesses that have been great in the past.

Looking forward to bright headlights again....
ezhacker1San Francisco · Aug 27, 2019#108
I too went from diode between the hi and low to Morimoto MotoControl. Best thing ever. But i do hate these housings for retrofitting (Morimoto Mini D2s 5.0) ... my driver side high beam solenoid must have been disconnected. But I have 2 six inch light bars in the grille for high beams that do so much more.
DeeBeeAustralia · Aug 27, 2019#109
Originally Posted by ezhacker1 ↑
I too went from diode between the hi and low to Morimoto MotoControl. Best thing ever. But i do hate these housings for retrofitting (Morimoto Mini D2s 5.0) ....
I have had Morimoto Mini H1's and D2S' on Rav4 and Corona and they were fantastic. On the Yaris I'm holding out since I have a working JDM setup. I think the D2S 5.0 will be the next upgrade. For now I'm looking to get a Morimoto harness to drive the JDM units for another few months before I decide to upgrade.

What's the issue with the housings? I'd think it would be easy since they are big. My Rav4 had really small headlights and it was a pain trying to get the projectors in right.
ezhacker1San Francisco · Aug 27, 2019#110
You still have to cut around the OEM bulb opening to fit the thread of the projector. Also threaded on without modification means the beam is too low. You run out of vertical adjustment. Could well possibly be I'm using aftermarkets housings as I dont have 08 style OEM, my car is 09. But the aftermarket allows me to have horizontal adjustment.

Mini D2S 5.0 is much better than the 4.0 IMO. the step isnt as big. I hated the dead zone of light on the lower step. Highbeams always looked good for these projector price range.
DeeBeeAustralia · Aug 28, 2019#111
Thanks for the info. I'll certainly take a good look at vertical adjustment when I make that move.
fredovvtiSabana Grande, PR · Dec 29, 2019#112
I change mines to LED and the different is BIG!! Try it!!
BIGTAZ351North Branch, MN · Jun 1, 2020#113
OK I was wrong last year about the Negative Switched, and before I go back out and start hacking on my cars (ok being too lazy, and at work, to go back out with my meter) I wonder if any of you experts know... IS The Positive Terminal on the H4 Halogen lights (Right at the bulb) "Hot" ALL the time?

OR Hot ONLY when The Headlights are turned ON?

Your Input is Appreciated!
govtecThread starterPhila, PA · Nov 15, 2020#114
Hi guys, so after 3 years my low beams suddenly stopped working the other day. High beams and everything else works. I’ve checked the engine bay 10 amp fuse and they are fine. Any idea where I should look next? Thanks
enviriCT · Nov 15, 2020#115
ballast and bulb. its 90% most likely the bulb. both went out at the same time eh?
govtecThread starterPhila, PA · Nov 15, 2020#116
Originally Posted by enviri ↑
ballast and bulb. its 90% most likely the bulb. both went out at the same time eh?
Yes, at first I doubted both bulbs would go at the same time so I just ordered 2 D2R Osram bulbs from Amazon. I also tried switching out the headlight switch with a new one from Toyota and that didn't work. We'll see if the bulb solves it. Thanks
enviriCT · Nov 22, 2020#117
wait you're using d2r with toyota ballasts? that might not be good...should be using d4rs... D2Rs use a good deal amount more energy to light up. It just might be your ballasts too!
govtecThread starterPhila, PA · Dec 20, 2020#118
I ended up taking the vehicle to a local mechanic shop and they determined it was a bad relay. They changed it and put a new one in and it's working fine now. Where is the location of the low beam relay?

I used d2r because that is what the HID housing said to use. I also have a relay harness setup...https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
govtecThread starterPhila, PA · Dec 29, 2020#119
Quick question...Has anybody tried substituting the H4 male plug with a 9006 male plug to the 4 prong connector?...I'm finding that the cheap H4 relay harness is about to die on me and keeps flickering when I hit a bump on the road after about 3 years of use and I can't seem to find a quality H4 relay harness in the market. Morimoto makes a 9006 relay harness but will require a 9006 plug, so that is why I am asking this question. Thanks

1 attachment not included in this copy