its the other one of the 2 t10 connectors for the stock headlight...the side marker light.
DIY: OEM JDM HID Headlight Conversion
119 posts · 72,881 views · page 2 of 3
Replies continued
Pic # 1 below show's how the 2 ends of my 194/t10 parking light extension cable that I ordered. Is this the right one?
Pic # 2 shows the 2 plugs that I have left to use and none of them will fit 194/t10 cable from pic # 1.
Pic # 2 shows the 2 plugs that I have left to use and none of them will fit 194/t10 cable from pic # 1.
2 attachments not included in this copy
yeah both of those unused plugs are for parklight bulbs. i used the one to the right, the brown one i use as a hood lamp.
Picture not included in this copy
i assume you still have this? it may still be connected to your headlight, next to your winker bulb.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
i assume you still have this? it may still be connected to your headlight, next to your winker bulb.
Picture not included in this copy
Picture not included in this copy
I see what you did. I'll have to wait until the weekend since the headlights are at my parents house.
Do I cut-off the other end of 3 so I can splice the wires to the 4 prong and parking light? Thanks
Do I cut-off the other end of 3 so I can splice the wires to the 4 prong and parking light? Thanks
splice away.
Enviri - Need your help urgently while I'm doing the installation...So far I've installed one side of the JDM HID lights on the passenger side and after I've plugged everything in, the parking light is constantly on without the keys in the ignition. Even after I start the car, the low beam and the rest of the lights do not come on in the JDM HID headlights while my US headlight on the driver side functions normally. What am I missing?
3 attachments not included in this copy
On post # 31 you had mentioned something about an extra ground going from the green/black parking light wire to the chassis...After I spliced the extension parking light wire, I connected one of the wires to the black parking light wire in the headlight housing. Is this what you meant by post # 31? Or is there another step I'm missing. I'll get to my parents house later this afternoon and I'll check all the wires and plugs again just to make sure I didn't miss anything.
Thanks
Thanks
I'm ordering another pair of T10 and H4 plugs because the ones I got are of bad quality. I also blew out the tail light and passenger low beam fuse.
something tells me that there is definately a crossed wire somewhere, grounded to the chassis or not. CTScott recommended we grounded the parking light to chassis for safety reasons.
Update...I finally received the relay wiring harness that fredovvti had suggested I use to solve the power issue for the JDM headlight. I ordered it from Amazon...https://www.amazon.com/LIGHTING-Cera...op_mb_pd_title. After I finished with the installation and drove home from my parents house, the low beam (hid bulbs) would flicker when I start the ignition and the switch stalk is turned off and the blue high beam CEL would come on the dashboard. The light would continue to flicker when I turn on the parking light with the first turn on the light switch stalk. When I turn on the low beam, the flickering stops and I get a solid beam. The same holds true for the high beam as well when I push the light switch back.
Any idea where I should look?...I grounded both the H4 relay harness and Parking Light on the passenger side to the chassis located on front near the radiator. I grounded the Parking Light and H4 relay harness on a factory ground bolt near the air intake duct on the driver side.
Check out the pics as well as the video of the lights flickering.
Any suggestion on where to look or alternative grounding location is appreciated.
Thanks
https://drive.google.com/open?id=1E9...pMG96lJhJfjb1c
https://drive.google.com/open?id=1KC...3i2HiLmm8gEMm4
https://drive.google.com/open?id=1Md...HXMxClRw_NOuYp
https://drive.google.com/open?id=1jG...t9kXnwhQu4yVql
https://drive.google.com/open?id=1B6...OdjsJRlmW88baY
https://drive.google.com/open?id=1AK...IjaiTMbxVytDzX
https://drive.google.com/open?id=1zV...Li9mlopeuabTtd
https://drive.google.com/open?id=1oh...QhNkrBYHgKSSCU
Any idea where I should look?...I grounded both the H4 relay harness and Parking Light on the passenger side to the chassis located on front near the radiator. I grounded the Parking Light and H4 relay harness on a factory ground bolt near the air intake duct on the driver side.
Check out the pics as well as the video of the lights flickering.
Any suggestion on where to look or alternative grounding location is appreciated.
Thanks
https://drive.google.com/open?id=1E9...pMG96lJhJfjb1c
https://drive.google.com/open?id=1KC...3i2HiLmm8gEMm4
https://drive.google.com/open?id=1Md...HXMxClRw_NOuYp
https://drive.google.com/open?id=1jG...t9kXnwhQu4yVql
https://drive.google.com/open?id=1B6...OdjsJRlmW88baY
https://drive.google.com/open?id=1AK...IjaiTMbxVytDzX
https://drive.google.com/open?id=1zV...Li9mlopeuabTtd
https://drive.google.com/open?id=1oh...QhNkrBYHgKSSCU
Problem solved!...I disabled the DRL and the rest of the lights no longer flickers!
1 attachment not included in this copy
Hi all,Originally Posted by ezhacker1 ↑H4 Connector is switched ground. Low and Hi has their own ground pin.
Based on Enviri connector photo and pin orientations im guessing
Red Low Beam
Black Hi Beam
Green Parking
Black 12v.
I know this is an old thread but I just found it recently and ordered a set of JDM HID headlights for my ride.
I was hoping to get clarification on the wire orientation to connect from the H4 to the HID connectors.
Black is quoted as 12V, Hi Beam, and in some cases, Ground.
Could you please help me out with the correct orientation.
Thanks in advance,
DeeBee
What I did was basically followed the orientation of the 4 prong pins that enviri showed in the videos. If you do that you should be fine and just trace it back to the plugs in the headlight to confirm the orientation.Originally Posted by DeeBee ↑Hi all,
I know this is an old thread but I just found it recently and ordered a set of JDM HID headlights for my ride.
I was hoping to get clarification on the wire orientation to connect from the H4 to the HID connectors.
Black is quoted as 12V, Hi Beam, and in some cases, Ground.
Could you please help me out with the correct orientation.
Thanks in advance,
DeeBee
Don't forget to pull your DRL relay in post #62 so your lights don't flicker.
Thank you for your help. I was able to get the wiring done.Originally Posted by govtec ↑What I did was basically followed the orientation of the 4 prong pins that enviri showed in the videos. If you do that you should be fine and just trace it back to the plugs in the headlight to confirm the orientation.
I tested them with a battery charger and they worked well 🎉
When I plugged them into the car the HID do not come on 🤷
All other lights turn on. I know the bulbs work so it must be something to do with the car's stock wiring. I get the feeling there is not enough power to turn on the HID ballasts. I am not using a wiring harness.
Is everyone who has them working using a wiring harness? Please help me solve this before Christmas. I'd like to have them working for a road trip then.
Thank you for the reminder 👍Originally Posted by govtec ↑Don't forget to pull your DRL relay in post #62 so your lights don't flicker.
We don't have DRL on the '06 here in Australia so that won't be an issue for me.
The Yaris have a ground switch. You may have the wires reversedOriginally Posted by DeeBee ↑Thank you for your help. I was able to get the wiring done.
I tested them with a battery charger and they worked well 🎉
When I plugged them into the car the HID do not come on 🤷
All other lights turn on. I know the bulbs work so it must be something to do with the car's stock wiring. I get the feeling there is not enough power to turn on the HID ballasts. I am not using a wiring harness.
Is everyone who has them working using a wiring harness? Please help me solve this before Christmas. I'd like to have them working for a road trip then.
Sent from my CLT-L04 using Tapatalk
Hi IllusionX,Originally Posted by IllusionX ↑The Yaris have a ground switch. You may have the wires reversed
Sent from my CLT-L04 using Tapatalk
Thanks for your suggestion. I think the wires are ok since I get power to all other bulbs. In fact I tried swapping positions and the high beams came on at the low beam position.
My suspicion is that somehow there is insufficient power to turn on the HID ballast. I know they work because I have tested them with a portable battery charger and they light up well.
I had a Rav4 where the factory wiring powered HID projectors I had retrofitted without a wiring harness. I drove that for 7 years no problem. I expected the same from my little Yaris 😕
BTW govtec,Originally Posted by govtec ↑What I did was basically followed the orientation of the 4 prong pins that enviri showed in the videos. If you do that you should be fine and just trace it back to the plugs in the headlight to confirm the orientation.
The videos aren't available any longer🙁 so I'm not able to see if indeed my wiring is off.
Oh how I envy all of you that have these lights working.
I'm so close yet it feels so far off.... I hope to get this issue resolved and have the ability to see clearly in the dark.
I'm so close yet it feels so far off.... I hope to get this issue resolved and have the ability to see clearly in the dark.
I've looked up the EWD for the P90 Yaris and here's a few points to help you out.
As previously mentioned, the factory halogens are negatively switched. Assuming you had a H4 plug on the stock bulb, then you'll have one positive wire for each side and two negatives to switch between hi/lo. The factory wiring should be coloured as such
- RH positive = Black
- RH Hi ground = Green
- RH Lo ground = Blue
- LH positive = Grey
- LH Hi ground = Brown
- LH Lo ground = Blue
As with all wiring jobs, you should be testing everything with a multimeter as opposed to smashing some wires together and hoping for the best.
I haven't read back through this entire thread to compare everything with the wiring diagram, but here's a basic run down of things you should know
- Because the high and low beam run off the same positive wire, you only have a 10amp fuse for each headlight. This is probably borderline for just running the HIDs - ideally it'd be 15amp, but it's not enough to be running both the HIDs and the Hi beams, which leads me to my next point
- It's very likely that the JDM headlights have been designed to run both the HID and the Hi beam at the same time when you switch on the Hi's. If you look at the reflector bucket you'll notice it has two distinct sections - the upper for the HID lo beam, and the lower part for the hi beam. If these are anything like the 3rd gen JDM lights then running the hi beam without the low beam will produce two elevated spot lights in front of your car, but you'll have no width to the high beams. For this you'll need to wire the lo beams to stay on when you flick to hi beams. You should test the high beams out first, but I highly doubt Toyota designed these to be flicking between hi and lo with the lo being a HID setup. It takes way to long for HIDs to warm up and flicking them on and off shortens their life and the ballasts life.
- Re the above, I'm not even sure if the JDM headlights are positive or negatively switched, or how they've wired up the relays/computer to handle the HIDs.
If I were you I'd be building a new headlight harness with a few relays that are triggered off the factory wiring and wire these things up properly. Even better if you could get the factory wiring diagram ;) - https://page.auctions.yahoo.co.jp/jp/auction/g212047863
If you wanted to do it quick and dirty you could potentially just wire the lo beams in to get the hids working and then sort the hi beams out later.
I've been meaning to write up a piece on how to do all this to a third gen, which is conveniently positively switched with individual fuses per lo/hi beam, which makes things oh so much easier.
If I had my time again, I'd probably just throw bi-xenon morimoto projectors in my lights. While JDM reflector based HIDs are better than the halogens they replace, they have nothing on a good projector setup. Light output and cut off is just not the same :(
Oh and if you're in a country that drives on the right hand side - please don't do this conversion. Think of your fellow motorists. The cut off kicks up to the left. You'll just be blinding oncoming traffic or you'll have the lights set so low they'll be useless.
As previously mentioned, the factory halogens are negatively switched. Assuming you had a H4 plug on the stock bulb, then you'll have one positive wire for each side and two negatives to switch between hi/lo. The factory wiring should be coloured as such
- RH positive = Black
- RH Hi ground = Green
- RH Lo ground = Blue
- LH positive = Grey
- LH Hi ground = Brown
- LH Lo ground = Blue
As with all wiring jobs, you should be testing everything with a multimeter as opposed to smashing some wires together and hoping for the best.
I haven't read back through this entire thread to compare everything with the wiring diagram, but here's a basic run down of things you should know
- Because the high and low beam run off the same positive wire, you only have a 10amp fuse for each headlight. This is probably borderline for just running the HIDs - ideally it'd be 15amp, but it's not enough to be running both the HIDs and the Hi beams, which leads me to my next point
- It's very likely that the JDM headlights have been designed to run both the HID and the Hi beam at the same time when you switch on the Hi's. If you look at the reflector bucket you'll notice it has two distinct sections - the upper for the HID lo beam, and the lower part for the hi beam. If these are anything like the 3rd gen JDM lights then running the hi beam without the low beam will produce two elevated spot lights in front of your car, but you'll have no width to the high beams. For this you'll need to wire the lo beams to stay on when you flick to hi beams. You should test the high beams out first, but I highly doubt Toyota designed these to be flicking between hi and lo with the lo being a HID setup. It takes way to long for HIDs to warm up and flicking them on and off shortens their life and the ballasts life.
- Re the above, I'm not even sure if the JDM headlights are positive or negatively switched, or how they've wired up the relays/computer to handle the HIDs.
If I were you I'd be building a new headlight harness with a few relays that are triggered off the factory wiring and wire these things up properly. Even better if you could get the factory wiring diagram ;) - https://page.auctions.yahoo.co.jp/jp/auction/g212047863
If you wanted to do it quick and dirty you could potentially just wire the lo beams in to get the hids working and then sort the hi beams out later.
I've been meaning to write up a piece on how to do all this to a third gen, which is conveniently positively switched with individual fuses per lo/hi beam, which makes things oh so much easier.
If I had my time again, I'd probably just throw bi-xenon morimoto projectors in my lights. While JDM reflector based HIDs are better than the halogens they replace, they have nothing on a good projector setup. Light output and cut off is just not the same :(
Oh and if you're in a country that drives on the right hand side - please don't do this conversion. Think of your fellow motorists. The cut off kicks up to the left. You'll just be blinding oncoming traffic or you'll have the lights set so low they'll be useless.
Like stidnam said, you may want to use a voltmeter to make sure you get the correct ground and positive. Halogen bulbs don't care about polarity, but polarity is very important with HID.Originally Posted by DeeBee ↑Hi IllusionX,
Thanks for your suggestion. I think the wires are ok since I get power to all other bulbs. In fact I tried swapping positions and the high beams came on at the low beam position.
My suspicion is that somehow there is insufficient power to turn on the HID ballast. I know they work because I have tested them with a portable battery charger and they light up well.
I had a Rav4 where the factory wiring powered HID projectors I had retrofitted without a wiring harness. I drove that for 7 years no problem. I expected the same from my little Yaris 😕
H4 was designed with a common ground and 2 positive, but the Yaris has a common positive like mentioned above.
Sent from my CLT-L04 using Tapatalk
yes, the jdm factory HIDs are indeed designed to have both run at the same time when high beams are on. My high beams are regulated to flash duty only.
I have repeatedly blown the 10A fuse, and moved to 15A.
If you want both beams on, I'm pretty sure there will be alot of blown fuses, after the wire kung fu that's needed for it to happen...or you wire the hi beam up like it were a fog light.
I love the adjustment range of the HIDs and it can adapt to us roads well...that cut off is indeed there, but in the US where a vast majority of cars on the road are towering SUVs that blind the crap out of us...either they dont notice it, or if they do...SCREW EM.
*the high beams will definitely blind the other side really badly.
I have repeatedly blown the 10A fuse, and moved to 15A.
If you want both beams on, I'm pretty sure there will be alot of blown fuses, after the wire kung fu that's needed for it to happen...or you wire the hi beam up like it were a fog light.
I love the adjustment range of the HIDs and it can adapt to us roads well...that cut off is indeed there, but in the US where a vast majority of cars on the road are towering SUVs that blind the crap out of us...either they dont notice it, or if they do...SCREW EM.
*the high beams will definitely blind the other side really badly.
^^ as above, if it's blowing 10a fuses running both beams on factory wiring, that's proof enough to build or buy a proper harness to run these things :) The HIDs alone should be on 15a.
Hi stidnam,Originally Posted by stidnam ↑I've looked up the EWD for the P90 Yaris and here's a few points to help you out.
As with all wiring jobs, you should be testing everything with a multimeter as opposed to smashing some wires together and hoping for the best.
- Because the high and low beam run off the same positive wire, you only have a 10amp fuse for each headlight. This is probably borderline for just running the HIDs - ideally it'd be 15amp.
If I were you I'd be building a new headlight harness with a few relays that are triggered off the factory wiring and wire these things up properly. Even better if you could get the factory wiring diagram ;) - https://page.auctions.yahoo.co.jp/jp/auction/g212047863
If I had my time again, I'd probably just throw bi-xenon morimoto projectors in my lights. While JDM reflector based HIDs are better than the halogens they replace, they have nothing on a good projector setup. Light output and cut off is just not the same :(
Thank you for your detailed input👍
I installed 15 amp fuses to replace the 10 amp factory headlight fuses.
I am now looking to build a harness for the headlights to handle the HID power requirement.
I agree with you on the Morimoto projectors. I had a set in my Rav4 and they were amazing!! I wanted the Yaris to look stock and so I ordered these JDM HID headlights to avoid bringing attention to the car while increasing light output.
Hi enviri,Originally Posted by enviri ↑yes, the jdm factory HIDs are indeed designed to have both run at the same time when high beams are on. My high beams are regulated to flash duty only.
I have repeatedly blown the 10A fuse, and moved to 15A.
Thank you for this confirmation. I had hoped this would be the case on the occasional times I may need to use my high beams.
Just to clarify, I wasn't advocating to swap the fuses out as that may be a recipe for disaster if the circuits aren't rated for the amperage. I'd be aiming to build a harness with the correct gauge wiring and with a 15a fuse on each low beam and a 10a fuse on each high beam.
For what it's worth, the HID will probably still run on a 10a fuse, but they would have come with 15 from factory. It's the amp draw on start up that will blow the fuse anyway.
For what it's worth, the HID will probably still run on a 10a fuse, but they would have come with 15 from factory. It's the amp draw on start up that will blow the fuse anyway.
Guys I found this video, this guy is building a relay to archive that the low beam stay on when trigger the high beam. I will tray this if work on ours jdm headlights.
https://youtu.be/zxJbmIKp2KM
Sent from my SM-N950F using Tapatalk
https://youtu.be/zxJbmIKp2KM
Sent from my SM-N950F using Tapatalk
Hi fredovvti,Originally Posted by fredovvti ↑Guys I found this video, this guy is building a relay to archive that the low beam stay on when trigger the high beam. I will tray this if work on ours jdm headlights.
https://youtu.be/zxJbmIKp2KM
Thank you for sharing this link. I hope a little re-wiring of my harness gives me this result.
Thank you all for guiding me through this install.
I have the lights in the car and that was my Christmas wish of lighting up the road so I can see better! The light output is amazing in comparison to halogens!
What remains is rewriting my harness to keep low beams on when I select high beams.
I really appreciate the advice, guidance, kind words, and valuable information provided by members of this group. I am truly grateful. Thank you one and all.
I have the lights in the car and that was my Christmas wish of lighting up the road so I can see better! The light output is amazing in comparison to halogens!
What remains is rewriting my harness to keep low beams on when I select high beams.
I really appreciate the advice, guidance, kind words, and valuable information provided by members of this group. I am truly grateful. Thank you one and all.
Hi enviri,Originally Posted by enviri ↑yes, the jdm factory HIDs are indeed designed to have both run at the same time when high beams are on.
I can confirm that when I select high beams, my low beams turn off🙁
I rewired my harness following the link shared by fredovvti but the result did not change🙁
I think the wiring maybe different up at the switch/fuse terminals🤷
I love the HID output but its frustrating on the country roads here where high beam would be nice to see further out at a depression.
wish i can help you with that lo and high beam problem..i only have 1 theory that may or may not work. (wiring the H7 high beams as a fog light instead).
any other options and im scared there will be shorts or small fires lol.
any other options and im scared there will be shorts or small fires lol.
I have tried everything I can think of and I either get ALL lights on throughout or high beams or low beams.
I think I will try use a diode at the low beam and high beam relays to see if I can get it to work. Theoretically it looks possible. I'm not sure what size diode I will need.
If this doesn't fix it I will just live with either low beam or high beam.
I think I will try use a diode at the low beam and high beam relays to see if I can get it to work. Theoretically it looks possible. I'm not sure what size diode I will need.
If this doesn't fix it I will just live with either low beam or high beam.
Finally, I have success!!
The low beam stays on when I select the high beam 🎉
I used a 6A 400V rectifier diode between the low and high beam ground wires connected to the low and high beam relays.
So far the result is what I have been looking for 👍
Thank you all for your help along the way!!!
The low beam stays on when I select the high beam 🎉
I used a 6A 400V rectifier diode between the low and high beam ground wires connected to the low and high beam relays.
So far the result is what I have been looking for 👍
Thank you all for your help along the way!!!
BTW, factory headlight fuses are back to 10A since the relays are doing the "heavy lighting" now.
I will test it out for a few days then wrap all the wiring connections in a good loom ro something similar.
I will test it out for a few days then wrap all the wiring connections in a good loom ro something similar.
nice! How did you attach it?
Excelent!!! Pictures please!!!
Sent from my SM-N950F using Tapatalk
Sent from my SM-N950F using Tapatalk
I know. this sounds dumb... but....How do I post pictures here?
Postimages.orgOriginally Posted by DeeBee ↑I know. this sounds dumb... but....How do I post pictures here?
If you are on mobile, use Tapatalk
Sent from my CLT-L04 using Tapatalk
There is a sticky thread in the Photo subforum. FAQ: How to post picturesOriginally Posted by DeeBee ↑I know. this sounds dumb... but....How do I post pictures here?
Sent from my EML-L09 using Tapatalk
Let me try attaching a couple of pictures.
Picture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copy
Sent from my iPhone using Tapatalk
Picture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copy
Sent from my iPhone using Tapatalk
The diode connection is in the first pic. Temporary but functional.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Thanks heaps👍Originally Posted by IllusionX ↑
If you are on mobile, use Tapatalk
Sent from my CLT-L04 using Tapatalk
Thank you!! Picture not included in this copyPicture not included in this copy
Sent from my SM-N950F using Tapatalk
Sent from my SM-N950F using Tapatalk
In this image, you can make more details, I 2 cable connected to the diode. Those are the negative im correct? I see to red taped together what are those?
Thank you for your response.Picture not included in this copy
Sent from my SM-N950F using Tapatalk
Thank you for your response.Picture not included in this copy
Sent from my SM-N950F using Tapatalk
Hi fredovvti,Originally Posted by fredovvti ↑In this image, you can make more details, I 2 cable connected to the diode. Those are the negative im correct? I see to red taped together what are those?
Thank you for your response.Picture not included in this copy
Sent from my SM-N950F using Tapatalk
In the image showing the relays, yes, I connected the low beam negative and high beam negative terminals.
The relays are part of a harness I purchased to get the ballasts to turn on. Sadly, in an effort to get this mod working I butchered the harness quite a lot trying to get it to work. I'm not sure I can get it back to the way it was wired when I bought it but it works fine now.
Initially, I connected both negatives and all lights came on, all the time - Not good. Eventually I discovered that all I needed to do was connect both negatives using a diode to keep high beams off during low beam operation and during high beam operation keep the low beams on.
I am very happy with this mod because I can flash to see ahead at a corner without losing the HID wide-angle view.
Interesting, so it only connwct the negatives wires to the diode. I will try went my extra relay harness arrive. Thank you for the respone.
Sent from my SM-N950F using Tapatalk
Sent from my SM-N950F using Tapatalk
That is correct. The diode only connects the negative wires.Originally Posted by fredovvti ↑Interesting, so it only connwct the negatives wires to the diode. I will try went my extra relay harness arrive. Thank you for the respone.
Sent from my SM-N950F using Tapatalk
Looking forward to hear how it goes for you once you get your harness.
Att lastt!! Thanks to Deebee for the help I conquer the hi/low beam in same time. Now I have full jdm lights!!! I connect the diode with hi and low.Picture not included in this copyPicture not included in this copy
Sent from my SM-N950F using Tapatalk
Sent from my SM-N950F using Tapatalk
Glad to have been of assistance🙂Originally Posted by fredovvti ↑Att lastt!! Thanks to Deebee for the help I conquer the hi/low beam in same time. Now I have full jdm lights!!! I connect the diode with hi and low.Picture not included in this copyPicture not included in this copy
Sent from my SM-N950F using Tapatalk
I am happy to see it worked for you too🎉
The lights are just amazing👍
I like the way you connected your diode. I should have done it the same way to save on the time I spent removing the contacts from the relay connectors😕