Yarisworld Archive

2018 Yaris SE 5MT - T-Sport w/Valvematic!

131 posts · 122,305 views · page 1 of 3

atomic_hojiOriginal postKincardine, ON, Canada · Aug 16, 2017#1
Hello All!

I've loved my 2007 FJ Cruiser and had lots of good times with it, but we decided as the family has grown and everyone needs to be out and about to different places all the time that it's time to move on from the truck; seriously, the FJC rear doors are not small kid friendly.. 😆 After some serious reading (lots here on Yaris World) we've decided to stay in the Toyota family and have a 2018 Yaris SE 5MT on order - coming soon (soon'ish? Not soon enough!). Apparently SEs aren't common and neither are 5MTs, so have to wait for a build.

As there's no picture yet, posted a placeholder (with appropriate details blanked) for the time being.. 🙂
-- Adam

EDIT (16-Oct-2017): It's here! Arrived last Saturday, been driving it this week - fun little ride. Engine pic to show the 1NZ before the swap; for reminiscing. When I paid for oil spray (we salt the heck out of our roads) I assumed it was underspray, not all-over-the-entire-body-of-the-car spray.

Picture not included in this copy
Picture not included in this copy

EDIT (27-May-2018): Picture of the final engine bay after the 2ZR-FAE install.
Picture not included in this copy

--

Overall Swap Summary
This thread is a build as it progressed and has tidbits of information, discussion, etc.. through-out. I've included this brief summary as the short, to-the-point version noting what was needed to do the swap, but without discussion as to how it was completed.

Engine
A complete 2ZR-FAE from the wrecker including the main engine wiring harness, intake and exhaust manifolds, injectors and fuel system, ignition coils, all sensors, and ancillaries such as starter, A/C compressor, and alternator. The RH engine mounts - both the engine side bracket and the frame side mount - from a Scion xD were used as per the 2ZR-FE swaps already documented.

Cooling System
Radiator filler neck, and radiator and heater hoses from the Scion xD were used: inlet and outlet heater hoses, and upper radiator hose; lower radiator hose from the Yaris was retained, though is a tight fit on the 2ZR thermostat housing. The Yaris radiator was retained. A short piece of 30mm radiator hose is needed to connect the Scion xD filler next to the radiator. The hoses route much easier versus using the Yaris hoses and create space for the main engine harness to the new ECM location.

Exhaust
A 2012 Scion xD complete exhaust system was used, however it does not bolt up without modification. The main pipe is not long enough to reach the rear hanger on the Yaris so the pipe was cut and extended. The rear hanger bracket is in a different location and had to be cut and re-welded to match the Yaris location. The 2ZR-FAE exhaust manifold from the iM does not center in the Yaris exhaust hole so the manifold to main pipe connection is poor - a modified bolt-up method was used to clamp the two parts enough to stop exhaust leakage.

Intake
The Injen Cold Air Intake system for a Scion xD was installed, however, like the exhaust it requires modification. The shape of the 3rd gen. Yaris front-end means the CAI interferes with the LH headlight assembly and the bumper reinforcement. The CAI was cut and shortened to make a 'ram air intake' instead.

Ancillaries
Most of the ancillaries on the engine were retained and plugged in without modification. The A/C hoses from the Yaris were retained and matched the ports on the iM A/C compressor with a bit of finagling. Reinforced PVC hose was run between the vacuum pump and the brake booster as the 2ZR-FAE uses a separate vacuum pump; there is no OEM hose to use. Similarly, heater hose (to be replaced with PVC when canister is installed) was used to run the connection between the PCV port and the intake manifold.

Transmission
The C50 from the Yaris was used and generally unmodified - the Yaris back-up switch was removed and replaced with a iM style back-up switch to match the main engine wiring harness connector. Flywheel, clutch, and pressure plate from the 2ZR were already installed on the engine, so those were used in place of the Yaris setup.

Electrical & Wiring
The ECM was relocated from the RH side firewall to the LH side of the engine bay. Custom brackets were built to hold the Scion iM ECM in front of the battery location. The wiring was fished out of the Yaris harness and re-routed to the new location, and the iM engine harness is bent over the Valvematic box to mate at the new location. The engine to body connector was converted from 18-pin + 2 pin connector setup to match the Yaris' 26-pin connector. An additional connection to power the Valvematic system was also wired in. Modification to the fuel pump control system was made to run the fuel pump and an external cooling fan control setup was installed due to differences between the Yaris and iM ECM control methods.

3 attachments not included in this copy

Replies 130

atomic_hojiThread starterKincardine, ON, Canada · Aug 16, 2017#2
And now the reason for the title and the post to the Performance section... 😁

Why? Because http://www.subcompactculture.com/201...g-racings.html

The addiction to build a 2ZR was then fuelled by the awesome threads found here on Yaris World. And now here I am... 2ZR-FAE from a 2016 Scion iM sitting in my garage awaiting it's new home.

I'm working through wiring diagrams and know I need to repin a couple of connectors so far, but overall it looks well do-able. Have a couple of small items on order, few parts to collect, and connectors to order, but given the quoted time for delivery is October.. lol.

1 attachment not included in this copy

atomic_hojiThread starterKincardine, ON, Canada · Aug 16, 2017#3
Hmm.. YW newbe, follow-up post with 2ZR-FAE pic is MIA. Mod approval req'd? Not quite the same as SONTT.

BTW - If there's any former SONTT members out in YW say Hello!

-- Adam

edit: updated with eye candy; including that magic valvematic black box!

2 attachments not included in this copy

KalispelArizona (USA) · Aug 16, 2017#4
Grats on the pre-order. The Yaris SE is very nearly the perfect little runabout. 👍
atomic_hojiThread starterKincardine, ON, Canada · Aug 18, 2017#5
Appreciate it, thanks! 👍

I haven't come across a 3rd gen. swap yet or one that uses the 2ZR-FAE. So, I'm going to use this thread to document what I run into as I go in hopes of helping others that want to do it as well.

The 2ZR-FE swap is well documented on YW - and big thanks to those who have put so much good information up for the rest of us! The article on Subcompact Culture about Tom Armstrong's 2nd gen. sedan and the related YouTube video on TheSmokingTire channel is how I caught the bug.. Lurking YW sealed the deal. 😁

One of the elegant parts to the 2ZR-FE swap for the 2nd gen. is using the Scion xD harness and ECM as it is plug and play with the 2nd gen. Yaris. I don't have the 2nd gen. EWDs (if/when I subscribe to TIS again I'll have to remember to get them..) but I imagine a lot of the 3rd gen. wiring is the same or similar, save for additions such as TSS-C, etc.. so it would likely still work or maybe require modification - probably less than using a Corolla or iM; wait, why am I doing this the hard way..? lol However, the Scion xD isn't as common as a Corolla or iM, has no -FAE option, and won't have the updated features of the newest models. Unfortunately, sourcing from a Corolla or iM isn't quite as plug and play - very similar in many ways as fortunately Toyota is standard (lazy? 😉) about wiring - but will open the option of Valvematic and the modern ECUs have the gadget support if you can get a hold of a new enough ECU. Working through and documenting the wiring differences will provide an alternative to get the 2ZR-F(A)E into our 3rd gen. Yaris'.

With rainy weather yesterday and today I've been doing a rundown on the ECM diagrams. I'm using a 2016 Scion iM 6MT engine, harness, and ECM. Because most of the engine related sensors etc.. are on the large, 135-pin connector and included direct in the engine harness, and I have the matched set I'm less worried about these; also, it's 135-pins and mildly intimidating! lol I did the rundown on the 60-pin connector for differences between the iM and the Yaris..

-- Adam


Updated (18-Nov-2017): keep wiring information for the swap in one post in the thread, clean up the post, and add some additional information.)
Updated (27-May-2018): modifications to wiring as installed with the engine running.
--

ECM Relocation
As the Scion iM has the ECM on the LH side of the engine bay, along where the main engine Junction Box (JB) is, we have to re-route the 60-pin engine to body connector from the Yaris location on the RH side of the firewall over to the LH side of the engine bay.

This is most easily done with the 1NZ engine, the cowl, etc.. is already removed so that the engine bay is most accessible. Drop the wiring loom and fish the wires for the 60-pin connector out all the way back to the LH side of the engine bay. Then tape and re-install the remaining wires back up under the cowl. I installed 1/2" wire loom over the ECM connector wires and ran the line down the firewall to the LH side of the brake booster, under the main engine JB, to the front of the battery tray, where I have the ECM installed. Here's a picture showing how I fished the wires out. The ECM with the connector is shown in the picture in post #01 of the overall installation.

Picture not included in this copy

Modifications to ECM Connectors
The modern Toyota ECMs as used on both the Toyota Yaris and the Scion iM use two main connectors: a 135-pin ECM connector, called 'B38' in the iM EWD, is the main engine harness, which is on the engine and matches the iM ECM, so there's nothing to re-pin or worry about; and a 60-pin ECM connector, called 'A72' for Yaris or 'A31' for iM in respective EWDs, is the connection between the ECM and the engine room harness in the Yaris. There are 2 outputs on the 60-pin ECM connector that are 'dead-ended' due to differences between the iM and the Yaris.

Cooling Fan Control
45 - RFC - on the Scion iM outputs a variable signal from the ECM to a Cooling Fan ECU that controls the fan speed. The Yaris control, however, uses a simple relay system that provides grounds to terminals 07 - FANL - FAN NO.1 Relay, and 08 - FANH - FAN NO.2 Relay to select low or high fan speed. The Yaris connector has no wire for pin 45 of the 60-pin connector, so no wire was abandoned.

As I was not able to run a wire, I instead opted for an aftermarket fan controller. I used the Mishimoto Adjustable Fan Controller (MMFAN-CNTL-U18NPT); using NPT type sensor requires using an inline adapter versus the radiator probe - I used the Mishimoto Water Temperature Sensor Adapter - 30mm (MMWHS-30). Installation followed the instructions (ish). Since I pulled the fan control relays, I followed the install directions for drilling and screwing the controller and running the ground wire, however I instead used 12-16 AWG 1/4" male blade (aka: disconnect) terminals to create a jumper across the FAN NO. 1 relay (switch side) to power the fan, and from the FAN NO. 2 relay (switch side) to return the line to the fan controller. 12V ignition power was run to the FAN NO. 1 relay (coil side) via a 18-22 AWG 3/16" male blade terminal to provide the controller with power.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

Fuel Pump Control
21 - FPC - Similar to fan control, the Scion iM outputs a variable signal from the ECM to the Fuel Pump Control ECU that controls a variable speed fuel pump. The Yaris control is, again, a simple ground to enable a relay that provides power to the fuel pump once the engine is seen to be cranking. The Yaris connector does have a corresponding pin 21 for FPC, which using the modification below we will disconnect from the main engine JB connector and 'dead end' the wire with heat shrink; I've de-pinned the connector and kept the wire terminal intact to allow reversal if need be.

This is posted on page 3 of this thread - post #48 - but I've moved it in here for documentation purposes.

WARNING - this solution bypasses ECM control of the fuel pump! The factory ECM is designed to shut off the fuel pump in the event of an accident. If you do not, or are unable to, turn the ignition off in the event of an accident there is an increased risk of injury or death due to fuel system fire.

Intense, but seriously, it bypasses a safety feature - always be careful, and understand what you've changed and how it impacts the vehicle.. 👍

To jumper the fuel pump to the IGN signal remove the upper half of the main engine JB, disconnect connector 1E from the bottom side of the integrated relay assembly (skinny white rectangle), and pop out pin-11 (violet). Blank the pin as it will still have a live signal from the ECM with heat shrink and/or electrical tape. From a spare harness, I grabbed a matching terminal with a length of wire, inserted the new terminal into pin-11, and ran the loose end to a body ground connection. Alternatively you can cut the violet wire leaving a pigtail and solder/crimp to existing terminal, then run to body ground. What this does is put a permanent ground on the C/OPN relay coil which, since the relay coil is only provided power when the IGN relay is energized (key to ON), it won't have power when the car is off but once the key hits ON it will energize and start the fuel pump.

Note: I have the common relay block removed - you don't need to remove it, just unplug the connector from the bottom side once you're into the main engine JB and make your modifications.

Picture not included in this copy

--

Modification of Engine to Body Connectors
The connector(s) between the main engine harness and the body harness, 18-pin 'BA2' and 2-pin 'BA3' on iM and 26-pin 'CA3' on Yaris in the respective EWDs, supply power and signals from elsewhere in the vehicle to items on the engine. Left is the BA2 connector we are going from, the right is the CA3 connector we're switching to.

Picture not included in this copy

Below is the re-map that I used to map wires from BA2 into an OEM 26-pin female connector (p/n: 90980-12771) to mate with the Yaris' CA3 male connector:
(shown as iM BA2 PIN# [terminal size] --> Yaris CA3 PIN# [terminal size])

01 [1.5] --> 12 [0.64II]
02 [1.5] --> 20 [0.64II]
03 [1.5] --> 14 [1.5]
04 [1.5] --> 01 [1.5]
05 [1.5] --> 01 [1.5]
06 [1.5] --> 15 [1.5]
07 [1.5] --> blank
08 [n/a on ALL]
09 [0.64II] --> 'CA4' 04 - provide shielding for O2 sensor
10 [0.64II] --> 25 [0.64II]
11 [0.64II] --> 25 [0.64II]
12 [1.5] --> 19 [0.64II]
13 [n/a on MT]
14 [0.64II] --> 22 [0.64II]
15 [0.64II] --> 08 [0.64II]
16 [0.64II] --> 24 [0.64II]
17 [0.64II] --> 02 [0.64II]
18 [1.5] --> 15 [1.5]

and BA3 --> CA3
01 [1.5] --> 26 [1.5]
02 [1.5] --> new connector

There are a few differences to note. First, there are a few wires that need to be re-terminated to smaller size wire terminals - the BA2 connector uses more of the larger, 1.5 size terminals. You can order the correct sized open barrel terminals and re-terminate the wire or find a spare harness at a wrecker, cut and de-pin a connector to create 'pigtails' to use. I bought some open barrel terminals, but found the small sizes are so delicate that I was mangling more than I had success with. Ultimately I found a wrecker about an hour drive away, chopped and pulled a large section of engine bay wire harness from a 2007 Toyota Yaris hatchback, paid my cash, and have a number of spare OEM connectors and wire pigtails now.

Second, there are some differences in how wires are used on the iM engine harness versus supply from the Yaris side body harness. These are as follows:

The Yaris uses 1 power supply wire that is shared by both the injectors and the ignition coils, where-as the iM has separate supply wires, BA2-04 and -05 respectively. I have 'Y' or 'T' connected these two wires into one to map to CA3-01. As both use the same resistance injectors and ignition coils I'm making the leap of faith that the supply will be sufficient for both on the iM engine harness.

The MAF B+ line is different between the two harnesses - the Yaris runs direct from the main engine JB to the MAF, where-as the iM expects a power line on the BA2 connector.
BA2-06 is Y/T connected with BA2-18 to map to CA3-15 to receive power.

BA2-07 is a ground to the engine block, however CA3 uses fewer ground connections, to the pin is folded back into the wire loom and heat shrinked.

BA2-09 is for the canister module ground, however the Yaris uses a local ground connection on the canister module, so it isn't needed for the same purpose. As for BA2-07 the Yaris needs fewer grounds on CA3, however the connector CA4 is the connector from the engine harness to the body harness for the O2 sensor, which needs a shielding wire (ground), so I've instead run this to CA4-04 for this purpose.

As for injectors and ignition above, the Yaris has only a single supply for the back-up switch and Generator IG lines, where-as the iM uses separate wires. These are similarly Y/T connected to map to CA3-25.

A new 30A fused wire from the battery was run for the Valvematic power supply (BA3-02) using a new, 2-pin male + female connector combo. I picked up a 5 pack of aftermarket connectors that are a match for the OEM cooling fan power connector through an online order. The terminals are a more manageable size than the connectors, so it was pretty straight forward to crimp the wires and install the sealed terminals into the new connector.

Transmission Back-up Switch
A simple change that was made was to remove the Yaris back-up switch which uses a different connector and install a iM style back-up switch in place. The threads are the same, so it is literally a matter of removing the old and installing the new. When the transmission is mated to the 2ZR the connector is routed right into place where the new switch sits.

Picture not included in this copy

7 attachments not included in this copy

dengMI · Aug 18, 2017#6
I love how much research your putting in to your swap. Only 3 posts, no questions, or bs, straight to the point.

Respect.
atomic_hojiThread starterKincardine, ON, Canada · Aug 18, 2017#7
Thanks for the props, deng. 👍

Plan is to be have these differences documented and addressed ahead of time so when I'm ready to swap it goes in smooth - don't want an on-going, troubleshooting nightmare with my reliable set of wheels. Hell, if I get it all correct and it goes in smooth maybe it'll encourage others to follow suit with the -FAE. 😆

With more rain today interfering with my wood shed building plan I decided to rundown the 135-pin ECM connector for a bit this afternoon instead - garage does smell great with the stacked spruce lumber.. lol

Found P/N: 82121-12U30 is for the 2016 Scion iM MT if you need to buy a new, complete harness ($$$). The same part number also applies for the 2017 Corolla iM MT. So if you're searching the wreckers either year will work, but be aware of (or prepared to repair) wiring harness butchering! Also, if you have a newer model Yaris the 2017 ECM will support the TSS-C functions; I will give TSS-C up for this swap using the 2016 ECM.

Never-the-less, the important part: for the 135-pin ECM connector, which is integrated into the engine harness, I tracked all wires by colour and connector and everything from the ECM pinned out on the 135-pin connector is on the engine harness proper (sensors, MAF, cam control, etc..) or goes to the vehicle via the 2 interface connectors (18-pin + 2-pin), respectively. Unfortunately, my meter leads are too fat to fit in the 135-pin connector so I wasn't able to continuity test each wire to verify, but all the colours jived at the appropriate connectors.

Still working to map those 2 connectors to the respective connector on the Yaris, but at a glance it should be do-able.

Quick note for my case: my engine harness was 95% complete from the wrecker - I got pretty lucky that they disconnected most connectors instead of butchering the wiring. Unfortunately, they did chop the wires right at the harness that run to the O2 sensor. On the iM this is a straight wire run, however on the Yaris the wiring to the O2 sensor goes via a connector at the engine room JB. I'll have to do a repair and pin them into the Yaris connector to pick-up the Yaris' O2 sensor. Also had a good bit of news about my engine pull via the CarProof report. Seems the car was at the dealership for service at 101 kms, then 6 weeks later was written off in a rear-end accident. I figure, assuming average driving, there can't be more than 2000 kms on it. Feel bad about the poor luck of the person who purchased it, but am happy to score a seriously low mileage unit! 😁

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Nov 2, 2017#8
Been busy on a plant equipment shutdown crew, then started a new job a couple weeks ago, but as noted above new Yaris arrived and bits ordered have been showing up over the past few weeks so thought I'd put in a quick update.

Parts collection is on-going, but have the below shopping list complete:
  • 2ZR-FAE motor w/manifolds; flywheel, clutch & pressure plate; throttle body; water pump; alternator; and starter included.
  • A/C compressor
  • ECM and complete engine wire harness (need O2 repair)
  • Injen CAI w/MAF sensor

Still need to find:
  • Axle-back exhaust for 2.25" exhaust
  • Mid-pipe (direct fit catalytic w/resonator)
  • Passenger side engine mount (frame & engine) w/hardware
  • Wiring terminals and connectors

Started opening packages and found that my spangly new Toyota connectors so I can change the Scion iM connector to mate do not come with terminals 😕 Literally just the plastic housing - all the aftermarket connectors I've bought for wiring lights or other ancillaries have always come with terminals and grommets (if used)! If anyone out there has a good source for terminals I'd appreciate a heads up! 🆘

With cold weather settling in I have some outdoor projects to complete before we get winter settling in. But hoping with a few more internet purchases I'll soon have her ready to roll into the garage to start the swap!

-- Adam
tmontagueCaledonia Ont. · Nov 2, 2017#9
Awesome thread. Fwiw I've used a reman'd eBay a/c compressor and for the past 20k I'm I've put on it since the swap it has given me no issues.

Good luck with the wiring, an fae would be great
KalispelArizona (USA) · Nov 3, 2017#10
👍
CrankyOldManWest Michigan · Nov 7, 2017#11
Wow, that's an awesome score on your engine! My 2ZR-FE only had 3700 miles on it before the vehicle was rolled. It sat in the warehouse for almost 7 years as well, but fired right up and runs like a champ all day long!

Which terminals do you need? I've got a few bins of spaghetti wire harness mess that could be used for pigtails if I have the right ones. You'd be hard pressed to find the actual terminals in loose/bulk packaging and the OEM crimp tool probably costs $500 or more. Toyota isn't nearly as open with their connector sourcing as some of the USDM companies are, resulting in high costs or outright zero availability of them.
atomic_hojiThread starterKincardine, ON, Canada · Nov 10, 2017#12
Hey, thanks for the support guys. 👍

Winter decided to show-up with gusto last night.. Fortunately, I picked up a set of 172/65R15 Michelin X-Ice XI3s (which feel like fat little bicycle tires, I laughed when I got home from work and saw they had been delivered. Honestly, being used to running 33"+ tires on my trucks they're hilarious, but oh so much easier on the back to install! 😆). Unfortunately, they weren't actually on the car this morning when they'd have been handy, so that was this evenings task.

But anywho, with respect to the 2ZR..

I was able to get a line on a used A/C compressor from another 2ZR vehicle; Corolla or Matrix I think the guy said. It fits, has a 6-rib pulley, and sounds like tmontague's experience shows good luck, so I'll run with it.. 👍

Had a disappointing follow-up email about the Magnaflow midpipe though. Seems there's no ETA from Magnaflow for stock, so the order is on hold. Means back to looking for an exhaust setup. Debating waiting until Black Friday sales in a couple of weeks and having something shipped to Port Huron, then make a trip down.

Appreciate the heads up Cranky re: wiring. I found that Ballenger Motorsports carries some of the Sumitomo line of wire terminals that have equivalent Toyota part numbers. I assume they crimp on normally?! To document for those running into wiring in future, I found the following using the EWDs for each vehicle and the Toyota Wire Harness Repair Manual.

. I need to re-pin the main connector between the engine harness and the body (18-pin BA2 and 2-pin BA3 from the 2016 Scion iM MT wire harness, and 26-pin CA3 on the 2018 Yaris harness).
[BA2: 90980-12745]
Toyota: 82998-24290 --> Sumitomo TS F025 (08)
Toyota: 82998-24350 --> Sumitomo TS F060 (10)
[BA3: 90980-10916]
Toyota: 82998-12380 --> Sumitomo TS F187 (02)
** have to map to Sumitomo TS F060 as connector CA3 doesn't use the larger pins.

[CA3: 90980-12771]
Toyota: 82998-24290 --> Sumitomo TS F025 (22)
Toyota: 82998-24350 --> Sumitomo TS F060 (04)
** -12771 isn't listed in the version of the repair manual I have, but I matched the sizes found on BA2; number of pins overall and of each type differs from BA2.

. Need to run a line for the cooling fan CPU from JB to CPU, and power from CPU to fan.
[A24: 90980-10841]
Toyota: ???
[z1: 90980-10928]
Toyota: ???

. Need to repair 4 wires at harness to CA4 for exhaust O2 sensor.
[CA4: 90980–12639]
Toyota: 82998-24290 --> Sumitomo TS F025 (16)
Toyota: 82998-12340 --> Sumitomo TS F090 (04)

I guess that's the long version... 😁 Short answer is some wires with female terminals from an engine to body connector and what seem to be larger ones to populate the cooling fan connectors; haven't found the type of terminal yet. I'll get pictures when I'm in the garage this weekend and post them up and see if I can add a picture/description for each of the terminal types.

Take care.
-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Nov 10, 2017#13
Originally Posted by CrankyOldMan ↑
Wow, that's an awesome score on your engine! My 2ZR-FE only had 3700 miles on it before the vehicle was rolled. It sat in the warehouse for almost 7 years as well, but fired right up and runs like a champ all day long!

...
Man, you made a pretty good score there as well! Good to know there's few to no worries about time sitting on a shelf at the wreckers 🎉

Ya, I got pretty lucky, especially that they had all the matching parts, excepting the A/C compressor. I just happened to find it via car-part.com when looking around for a low mileage 2ZR-FE and debating the swap; decided to commit to the swap with -FAE and jumped on it! Once I picked it up and had the VIN I was able to get the CarProof report so I'd have something to verify / estimate the mileage, as if I recall the mileage was not listed in the ad, but they said it was very low. We'll see if my luck holds on with the rest of the project.. 😉

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Nov 12, 2017#14
For the main engine wiring harness connector this is what I'm trying to change. I should note that, like a lot of things I'm running into, I'm doing this to make the swap as elegant a solution as possible; i.e. plug 'n play as much as is reasonable. If you are so inclined you could always cut the 1NZ harness and retrieve 'pigtails' with the needed terminals - I just want to pull the 1NZ complete and unmodified, and leave an unmolested body harness; I don't intend to swap back to the 1NZ, but you never know what may come up.

The below pictures demonstrate the conversion that needs to happen and the terminals involved. LHS is the female BA2 connector on my 2ZR harness, RHS is the female CA3 to match the Yaris. I popped one of the larger terminals, but my camera just can't take a picture that close up. The 2 types of terminals are shown in the Wire Harness Repair Manual diagrams.

3 attachments not included in this copy

CrankyOldManWest Michigan · Nov 16, 2017#15
The smaller terminals can be removed with a paperclip or sewing needle. Make sure the retention lock is disengaged, poke the needle into the smile-shaped hole, gently pry up/down while pulling on the wire. Shouldn't take any real force to extract them.

What wires/signals don't match up, if any?
atomic_hojiThread starterKincardine, ON, Canada · Nov 18, 2017#16
^ Good tip, thanks Cranky! 👍

I did buy a $10 set of connector tools - they so far work 'so-so' 🙄 Will try your technique as well.

So, after finally mapping everything out, it's actually not as terrible as I thought it might be; guess it makes sense that if on one vehicle you need an 18awg wire, it'll likely be the same size wire for the same function on the other vehicle.. 😆

I updated post #4 with the complete map (just pin numbers and terminal sizes; could add functions if there's interest, but got really busy and cluttered when I started putting it in..) The ones that don't match are:
(pin# [terminal size] --> pin# [terminal size] for function)

01 [1.5] --> 12 [0.64II] for Combo. Meter CHG- -> Generator L
02 [1.5] --> 20 [0.64II] for 5A ICS/ALT-S Fuse -> Generator S
07 [1.5] --> 22 [0.64II] for Cruise ECC; DLC3 SG -> Ground
12 [1.5] --> 19 [0.64II] for Brake Actuator EXI3 -> Back-Up Light Sw.

pin 07 --> pin 22 could actually work if I tie pin 07 & pin 14 together and use the pin 14 terminal to match the corresponding size on the male (Yaris) side.

And I made an executive decision to leave the 2-pin connector stuff separate and just completely re-connector it, instead of dorking around trying to find the associated 4.8 size terminals - this also gives me a 1.5 size location to run the MAF B+ line, which is different between the two vehicles.

I keep trying to avoid modification of the existing harness as much as possible, but it is creating more of a chore; there's something to be said for just getting an aftermarket connector with all the associated parts and just creating a new connection instead of mucking about. 😛
atomic_hojiThread starterKincardine, ON, Canada · Nov 23, 2017#17
Quick update: parts collections is slower than I'd hoped due to unavailability of the exhaust, as well as delays on the order for engine mounts and other misc. parts. Good news is both orders should be shipped next week. Also had an offer from a wheeling buddy to pillage the wiring harness from a parked 4Runner to see if I can find the connectors and terminals I need; I'll check into that this weekend.

With respect to the swap, I have a plan. 😁

Time is a bit of a premium at the moment since I'm currently on the first 6 month portion of training for my new job and have regular progress tests I have to study for. BUT, we break for the Christmas holidays, so I will have a 10 day stretch over the weekend before Christmas until New Years off. I figure that should give me enough time to finish outdoor clean-up before snow sets in, get the garage clear, and collect the remaining parts. Then I'll roll the Yaris into the garage for the break, and roll her out in 2018 a new machine. 😎

Once into the teardown and install I can get some pictures and update the thread with some (hopefully) useful solutions. The wait is killing me.. lol

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Jan 7, 2018#18
Hope everyone had a great holiday and happy new year! 👍

Long time since last update, but progress, slowly but surely, 'ish - mostly busy. Had a good holiday, lots of visits, had friends we don't see stay extra time from the New Year's weekend as well. Also had another progress test at work for training, so that took some important time; final course this month, then the big exam in February.

Got the 1NZ disconnected and pulled successfully. Things I'd do differently (i) get a cheap digital camera to document! The 2ZR swap is already documented well in other threads, but for my own use it'd be handy. I do have a cell phone camera, but between filthy hands and just forgetting about it as I got busy I didn't grab enough (many at all) pictures.. (ii) follow the goddamn instructions! 😆 I hadn't removed the front bumper, rad, etc.. assembly as I figured using an overheard 1 ton hoist I could pop it up and out.. maybe could have, but I made a whoops with my rigging and found the hard way there's not much space in the engine bay - found I had it all nicely setup, but engine mount was caught up, when it came free the transmission side dropped and the whole thing jump and banged around; nothing appears damaged on the Yaris, and on me it was mostly my pride and underoos - scrape and bruise will heal. Did scare the bejesus out of myself though..

Never-the-less, picture proof of progress: a naked engine bay and the clean looking little 1NZ with C50 on the floor.

-- Adam

2 attachments not included in this copy

atomic_hojiThread starterKincardine, ON, Canada · Jan 7, 2018#19
^^^ is how she's been for a bit over a week now. When I went out 23/24-Dec the garage was a balmy 8 C, with the cold snap lately it's about 2 C and is a bit miserable on the fingers and toes being out there. However, even in light of the chill, I've started into the wiring changes today, separating the line to the ECU from the body so it can be relocated to the main JB/battery area.

Good news, it does work! 👍

Pretty straight forward, but for someone following as reference I did the following: dropped the wiring plastic clips to get it free. Then as I removed the tape from the wire bunch gently separated the wires for the ECU connector from the rest of the body harness and reapplied tape as I went to avoid it becoming a loose mess. Only tools were a sharp knife, pliers for the clips, and electrical tape. Obvious note: be careful what you cut! 😛

The main body wiring will get the plastic clips reattached and put back into it's stock position up under the metal lip you can see in the pictures.

I was able to run the ECU wires all the way back to where they come out of the hard plastic unit by the brake booster. This should give enough to run the connector to the ECU if I mount it at the main JB/relay box. The ECU wiring will get bunched and a few pieces of tape and then some plastic wiring loom over it for protection in the engine bay. If I do need to run it back to the stock location I will just run it alongside and retape it to the main body wire bunch.

-- Adam

2 attachments not included in this copy

atomic_hojiThread starterKincardine, ON, Canada · Jan 7, 2018#20
On a side note, with the holidays done, I needed wheels to get back to work last week.

Upside: I get to play with my FJ Cruiser again for one more winter.

Downside: I had to dig her out of over a foot of snow and change those mud terrain tires out for winter tires in -24 C weather. They dug through the snowbank nicely to get unburied, but are awful on packed snow / plowed roads. 😆

-- Adam

1 attachment not included in this copy

tmontagueCaledonia Ont. · Jan 7, 2018#21
Great to see the progress, are you all set for the wiring or are there still unknowns about that?

Id love to source a corolla ecu and slowly build up a proper harness so I could just do a plug and play with an fae engine and take advantage of the valve lift.

I can't have my car down for more than a day or two sonc sits my dd. If you're able to document the electrical and it works with everything else in the Yaris then this opens many doors for other YW members down the road for a somewhat straight forward swap
atomic_hojiThread starterKincardine, ON, Canada · Jan 9, 2018#22
Hey, thanks for the support man. 😁

Ya, I'm very lucky that I've been able to keep my truck in the meantime. I know for most people if it's a DD they need a weekend project, not multiple weeks of fuddling about.

I'm pretty confident about all of the wiring I need to take care of, but won't call it 100% until I get it completed (and proven to work!). I found while disconnecting the Yaris wiring that I had a mis-understanding of a couple of things - at least 1 thing will make life easier (woo!), the others not so much easier or harder, just a difference between what I expected and what's there. As I get the wiring steps done I'll get more pictures in and do a final write-up for others to follow once I've proven it works.

Without looking at the xD wiring, I would imagine with having the xD 2ZR-FE harness you could probably put that on a 2ZR-FAE and run the few wires for the VALVMATIC control and power; would have to confirm ECM mapping and finding wire terminals to match the ECM connector - might be tough if they aren't the same as other types used on the wire harness. Of course, I say that, but have still yet to open the connector to do the wire swap to give me my cooling fan ECU output.. lol

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Feb 3, 2018#23
Quick update: the cake is a lie; for now.

Short version: Yaris is in the same sad state sitting on jackstands as it was a few weeks ago, and is lowest on priority list for now until life is back in order.

The long, personal blogosphere version is that after such a good holiday, tides turned and it's been a bit of a rough go the past few weeks. Got news my Mum has cancer, she's now started chemo. Week later I got sick with what I thought was a dose of influenza; turned into pneumonia - been face down the past 2 weeks. Work is accommodating missed test, but exams are a different group, so bit anxious about being behind the 8 ball by 2 weeks..

Did find there's a semi-local U-Pull yard - wife drove past en route to a market with a friend - and from their website, they have a 2nd gen. Yaris in the yard. Once I'm up and about I'm going to go see what I can pull more harness and wiring; give me some spare bits and pre-crimped wires to play with.

-- Adam
Jeanseb29Gatineau (Ottawa), Canada · Feb 8, 2018#24
Hi Adam, hope everything is going to get better for you and your mom

Sent from my SM-N910W8 using Tapatalk
Jeanseb29Gatineau (Ottawa), Canada · Feb 8, 2018#25
It's a pleasure reading your posts and seeing how your car is progressing but take your time for taking care of yourself and your family. We will be here when you come back :)

Sent from my SM-N910W8 using Tapatalk
atomic_hojiThread starterKincardine, ON, Canada · Feb 10, 2018#26
Appreciate the kind words, thank you! 😁

We're getting there.. slowly but surely. lol Looking forward to early March when the chaos is (should be) done and we're closer to status quo.

-- Adam
hichamazizcasablanca · Mar 2, 2018#27
Appreciate it, thanks
atomic_hojiThread starterKincardine, ON, Canada · Mar 27, 2018#28
Ok, try #2 to update.. last Tuesday I had a day off before going back to my shift crew, so I thought I'd get an update posted. Then low and behold while I was logged into YW reviewing new posts I got a call from the hospital saying my Mum was in ICU and that if we can get up to the hospital we should do so asap; turned into a helluva week.. 😲 Mum's in stable condition, and the calm has finally returned again; for now anyway.

I'm not dead (not for lack of trying apparently.. lol) or run away from YW; the swap is not abandoned 'nor forgotten; and I haven't cut the 2ZR-FAE loose and put the 1NZ-FE back in. I also haven't copied the photos over from my phone, lol, so I'll have to update the post when I'm off next, but here's the skinny..

Progress:
  • 2ZR-FAE fits in a 3rd gen. Yaris using Scion xD RH engine mount and Yaris dogbone and LH transmission mounts; it's tight.. props to those who personhandled (zing Mr. Prime Minister, lol) the engine & transmission combo in solo!
  • Driveshafts are installed so car is finally sitting on the ground again - I've gotten used to it on jack stands, it's so low now! Caused myself extra work when I spun the axle nut off as I mangled the threads. Bought a rethread die and cleaned it up, worked a treat. 👍
  • O2 wire repair done; harness plug conversion nearly swapped - had to borrow a soldering iron and stuff to solder. I found the prefab solder and shrink conectors were a mess to deal with - heat shrink got a pinhole when solder melted and dripped. Doing the rest of the wires the old fashioned way with solder and heat shrink tube.
  • Pulled a 2nd gen. Yaris harness to get donor wires from so I can do a clean install (see below), but ...

Issues I have discovered:
  • In post #21 above I mentioned I misunderstood something. Ya, it's an oversight that I'm really embarassed about. I was so careful about all the wiring, then I neglected to pay attention to ECU pin sizes, so my idea of moving a FANH or FANL wire to RFC for an elegant solution was a no go. Unfortunately Toyota doesn't leave any unused wires for the AT on the MT harness, so no spare tiny pin wire to use either. Then I pulled a 2007 harness at a U-Pull and found the ECU difference between generations; figures, can't be bothered to change the rest of the car, but they go an update the connectors!
  • 2nd gen. Yaris ECU connectors are very different.. it uses 2 sizes of pins: large and small. 3rd gen. Yaris ECU and Scion iM ECU also use 2 sizes of pins: small and tiny. Two major things come out of this:
    1. I have no wire to steal to run my RFC (cooling fan) wire, and
    2. Based on this 2007 harness and the pictures of up to 2011 ECUs I found in a search (searching wire harness numbers found a ton of varying numbers over 2006 to 2011, so not as useful as I'd hoped..) the 2ZR-FAE swap as I'm doing it with the Scion iM ECU will not work on 2nd gen. Yaris'. 😢 Or rather, will not plug in as simply - you would need to find a modern 60-pin connector from a donor harness and chop it, then chop your ECU connector, remap, and solder all the active wires. I'd need a 2nd gen. set of EWDs to have a better idea. Here's hoping I'm wrong..
  • Yaris heater hoses are useable, but are a miserable mess; need to order Scion xD hoses.
  • Need custom hose for the vacuum piping between vacuum switch and hard pipe/tube on the firewall.
  • 2ZR-FAE uses an external, auxiliary vacuum pump! Crazy. Apparently an artifact of VALVEMATIC is that it can't use intake manifold for brake booster, so it has a vacuum pump on the rear side driven by the exhaust camshaft. Needs a short, custom tube between it and the brake booster.

So that's where it's at. Some reassembly in progress, which once the hoses and such are connected I'll fire the rad. support, rad., etc.. on and fill with fluids.

Looking towards an external, aftermarket cooling fan control setup. They exist and are pretty straight forward from what I've found in a quick search. Expect that the missing RFC line won't cause a problem since it's a variable resistance output only, but we'll see if it causes a CEL.

-- Adam

edit: added the evidence it's actually installed! 😁
Picture not included in this copy
Picture not included in this copy

and the difference between 2007 (left, bottom) and 2018 (right, top) ECU (body side) connectors:
Picture not included in this copy

3 attachments not included in this copy

stidnamAustralia · Mar 28, 2018#29
I've been watching your thread pretty closely eagerly awaiting updates. Sorry to hear about your personal situation. Hope things work out ok!

It sounds like a source for ECU pins/pigtails is your biggest problem at this point? Any chance of getting to a pick a part style wrecker to grab a few wires. Co-incidentally, I was at a wrecker last weekend here in Aus and they had an equivalent of your Scion IM in the yard :S

I've previously used this guy to source connectors and terminals in the past. Can highly recommend! - https://www.easternbeaver.com/Main/E...onnectors.html

FYI - you may also need to invest in a decent crimper if you don't already have one!

Personally, I think using the factory Toyota fan controller would be the cleanest solution. In saying that, I'd also agree with you re the CEL - That fan controller isn't connected to the CAN bus, and I wouldn't think the ECU would expect any feedback on FAN operation. Do you know what type of signal the RFC pin outputs? I thought it might be square wave, but perhaps it's a varying voltage?

On a separate point, I note you only used that RH engine mount and retained the other Yaris mounts. I was under the impression that this would result in miss-alignment of the motor (if only by a smidge). Have you found this to be the case? I'm currently hunting for the appropriate scion xd brackets, but they are proving very difficult to obtain from US based wreckers :(.
tmontagueCaledonia Ont. · Mar 29, 2018#30
hope you mom is doing better, sorry to hear about the setbacks but that's how it sometimes goes with projects cars. In this case you are also taking on a new project seeing as a 2018 has never been swapped with a 2zr and an FAE has also never been swapped.

After reading about your challenges I can see why the FE is typically the go to, seems to be a much easier plug and play since that is what the Scion xD uses
ArmstrongRacingSan Diego · Mar 29, 2018#31
I've been so impressed by this thread I haven't even known how or what to contribute...

Im sorry to hear about you mom, keep your head up buddy.

Let me know if I can be of any assistance.
atomic_hojiThread starterKincardine, ON, Canada · Apr 2, 2018#32
I really appreciate the kind words, thanks guys! Was a bit of a rough time a couple weeks ago, but things are heading in the positive direction so far. 👍

Was on my first set of night shifts in several months over the weekend, so no further progress, but off work the next couple days so I'm aiming to wrap up the last of the wiring (less the fan control) and re-assemble, fill fluids, etc.. that I can. Got my phone hooked up and downloaded the pictures to the computers, so I added the pics of the 2ZR in the engine bay and the clearance on each side as well. I have a bunch of odd and sod pictures of wiring bits, etc.. - trying to get pictures of things I've changed. Lots to go back through and update through the thread to ensure it's clear; sounds like a 'once-its-running' task.. 😁

Originally Posted by stidnam ↑
...
It sounds like a source for ECU pins/pigtails is your biggest problem at this point? Any chance of getting to a pick a part style wrecker to grab a few wires. Co-incidentally, I was at a wrecker last weekend here in Aus and they had an equivalent of your Scion IM in the yard :S

I've previously used this guy to source connectors and terminals in the past. Can highly recommend! - https://www.easternbeaver.com/Main/E...onnectors.html

Personally, I think using the factory Toyota fan controller would be the cleanest solution. In saying that, I'd also agree with you re the CEL - That fan controller isn't connected to the CAN bus, and I wouldn't think the ECU would expect any feedback on FAN operation. Do you know what type of signal the RFC pin outputs? I thought it might be square wave, but perhaps it's a varying voltage?

On a separate point, I note you only used that RH engine mount and retained the other Yaris mounts. I was under the impression that this would result in miss-alignment of the motor (if only by a smidge). Have you found this to be the case? I'm currently hunting for the appropriate scion xd brackets, but they are proving very difficult to obtain from US based wreckers :(.
With respect to the ECU pins, yes and no. Yes, because the RFC line for 2ZR fan control isn't going to work out the way I had imagined; if I'd looked closer in the first place I'd have maybe figured that out, but live and learn, lol. I say no because the ECU isn't really a problem in general as (less the fan control) connector-wise it is literally plug-n-play (does require ECU relocation). The conversion the main engine harness to body harness connectors - 18-pin 'BA2' and 2-pin 'BA3' on iM to 26-pin 'CA3' on Yaris - has been a bit of a pain; although I have the 'knack' for de-pinning now, so that part has become easy enough, lol. I have been fussing about with how to make that conversion as neat as possible. Of course, the real test will be plugging it in and nothing popping (best case a fuse..) and/or catching fire.. 😆 I've bookmarked the Eastern Beaver site, thanks! I used Rakuten Market (hi-1000) for the terminals I ordered, but always good to have many sources. Not many wreckers up in my area (pick-n-pull or not) have new enough Toyotas, but I'll keep an eye and plan the conversion to the factory fan control as an upgrade in future.

In searching the manual in the troubleshooting section I found a good description of the RFC output - it is a square wave output as you say and control is done by varying duty cycle based on engine coolant temperature; i.e. more demand, increase duration of 'on' portion of each pulse. But ya, since there's no feedback and it's not a CAN based control, I doubt it'll cause a CEL; worst case I imagine would be a troubleshooting code for 'fan not connected' or some such thing.

I did use only the Scion xD RH engine mount and it seems to sit in there fairly naturally. Using a chainfall (and not removing the sub-frame because I'm a dum-dum) it was a grunt to get it into the mounts. Once I had it in the RH engine mount, I had to use a prybar and force the whole assembly toward the RH side as the bolt for the LH transmission mount was about a 1/2" too far toward the LH side; this does mean that the LH transmission mount bushing is constantly loaded outward. Once it's driveable I will see if it has clunks and thunks, lol. Some of the guys that have done the 2ZR swap in the 2nd gens might be able to comment if they ran into the same thing (I don't recall reading that was the case, but those memory marbles were pushed out by exam prep. lol). I am a bit concerned about long-term impact on that bushing, but we'll see. I actually just ended-up ordering a new RH engine mount from an online Scion parts dealer. Maybe eBay? I've found some large wrecker companies are using eBay listings; it's how I picked up the correct A/C compressor actually.

Originally Posted by tmontague ↑
...
After reading about your challenges I can see why the FE is typically the go to, seems to be a much easier plug and play since that is what the Scion xD uses
lol, agreed! Although, that said, the FE is more straight-forward now because the odd and sod tidbits have been documented and worked through; tricks discovered by you guys who have finished the swap successfully. I imagine when Tom was working through the FE swap the first time he ran into unknowns. Once this is running and I look back and summarize what was really needed to make it work, maybe it won't seem like such a pain.

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Apr 2, 2018#33
Originally Posted by ArmstrongRacing ↑
I've been so impressed by this thread I haven't even known how or what to contribute...

Im sorry to hear about you mom, keep your head up buddy.

Let me know if I can be of any assistance.
Appreciate that, thanks Tom! 😁

All the work done by yourself and the others on YW documenting the original swap has been a huge amount of groundwork laid for doing this swap. I'm glad I can build on it, work my way through and document the FAE for the next person.

I'll keep the assistance offer in mind, thanks - I suspect most likely the call for help will be if I go to fire it all up and the immobilizer handshake doesn't work, lol. 😆

-- Adam
ArmstrongRacingSan Diego · Apr 2, 2018#34
The issue you mentioned with the LH mount being forced into alignment is exactly how I’ve been running my car since the swap. I chose that setup because it holds the drive-train tighter, and for racing purposes that seemed better. The mount is still in good condition with no tears (yet), but I’m unsure it it contributes to vibrations
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#35
Haven't updated in a while - only jumped on YW at all for quick posts - partly due to personal life and work being busy. Generally things are going much better, Mum's home now with appointments for follow-up and physiotherapy, and I ended up back on a day job (vs shift work). Again, appreciate the support from you folks on YW, thanks! 😁

Delayed thanks to Tom for the response on the engine / transmission mounts - good to know I'm seeing the same thing and you haven't (so far!) had any issues with it, even with the stress of racing being put on the car. 👍

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#36
So by far the biggest hold up to wrenching has been waiting for parts. You wouldn't think getting a couple of hoses would be so damn hard! 😛 I live a nice, rural area but unfortunately we don't have a lot of the big supply places - even the chains have to order most of what I want in.. Oddly the dealership had the part I wanted faster! lol

I solved an issue with the coolant line (upper rad.) and electrical (main ECU bundle) both wanting to occupy the same, small space between the Valvematic control box and the battery. Using the Scion xD filler neck assembly (p/n: ) and upper rad. hose will route the line under the air intake instead of over like in the Yaris. Did also order and use the Scion xD heater hoses - they route much better than the Yaris hoses do. Added the Mishimoto inline temperature probe adapter unit into the upper rad. hose so I can power the external fan controller as well.

So after finding enough bravery, I connected all the electrics (nothing exploded - woo!) and went through the Main ECM <-> Immobilizer ECU registration process, and ..

it's

ALIVE

...

almost.

So, this is where I'd appreciate any troubleshooting help you guys may be able to think of.. The summary of what's happened with it so far:

After registering the communication ID I went from ON to Start and it fired - actually, popped loudly, which startled the daylights out of me and I let off Start; found after that I had left the masking tape on the exhaust manifold.. lol Went from ON to Start again and it fired, ran for about 15s (counting mississippis) and stalled. I figured the immobilizer registered successfully as the manual says "ensure engine starts and runs for more than 3 seconds"; it did. So, I gathered it ran on fuel left in the fuel rail, but the fuel line just needed to refill. I disconnected the battery again (don't trust it yet) and went inside for the afternoon - watched Formula Drift Orlando Top 16 with the family.. 😁

Today, went out still with the assumption the immobilizer was solved and I needed to check I was getting fuel. Installed the exhaust - the short run stank out the garage and is loud as hell. Tried to fire it up to test it out and got combustion and a few second run, then fluttered, then stalled. Tried again, feathering the throttle, still assuming I needed to push fuel, ran for a few and then stalled even with the throttle slightly in. Did some checks, e.g. realized I forgot the O2 plug so plugged it back in, and found there's a buzzing/whine on the throttle body housing - wedged a board in the throttle pedal and confirmed the throttle body did open. Went OFF, then ON with OBD2 scanner hooked up and found no codes.. then Start to try again, and got the same thing - fires and flumps. Still trying to start with combustion, but something cuts it out right away - that part feels like immobilizer.

I have an OBD2 scanner, but realized (after trying a couple of times of course), that it's a pretty simple device that may not be reading the DTC code for the immobilizer, or any other Toyota specific DTCs. No generic codes are showing, but then the engine isn't running long, so may not have time to generate a code either.

One of the first times I tried today, after the 15s 'success' yesterday, I feel like I got several seconds, but wasn't counting.. These two things make me think the immobilizer isn't the issue, but with the various tries I have a (conservatively, since I didn't always cycle back to OFF and then ON) count of 10 tries. Manual says absolutely do not cycle more than 20 times or it will lock the immobilizer transponder ECU out and it will require replacement.

I'd like to put an immobilizer bypass in place and see if it fires and runs or behaves the same. If the bypass is a guarantee to work then it will rule out the immobilizer as an issue and I can focus on drive-by-wire, fuel (?), and start the dreaded task of chasing electrical gremlins - since I'm positive my soldering isn't perfect; though I thought I did a decent job, if I do say so myself. Alternatively, a bypass could prove the immobilizer was the issue and it'll start and run; in which case I'll put the hood on and give it a test drive.. lol.

As always, appreciate the support from everyone on YW! So close.. 😲

-- Adam

p.s. - do have more pictures, and have a list that feels like a mile long of things to run through so that I have everything captured. May try my hand at a video walking through the changes.. dunno if I have the mad camera skills like Tom. 😉
tmontagueCaledonia Ont. · Apr 29, 2018#37
Did you disconnect the immobilizer wires from the ecu?

My current set up had me running a non immobilizer ecu but i still had to disconnect 3 immo wires going into the ecu so it doesn't think that it should have an immo.

If your ecu has an immo I'm not too sure what the process would be other then using Toyota techstream software are having the ecu and immo ecu (located at the ignition) properly communicate to eachother
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#38
<placeholder>
Some wiring pictures.. have been removed. New pics to be added soon!
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#39
Originally Posted by tmontague ↑
Did you disconnect the immobilizer wires from the ecu?

My current set up had me running a non immobilizer ecu but i still had to disconnect 3 immo wires going into the ecu so it doesn't think that it should have an immo.

If your ecu has an immo I'm not too sure what the process would be other then using Toyota techstream software are having the ecu and immo ecu (located at the ignition) properly communicate to eachother
The iM will be an immobilizer enabled ECU. The Yaris workshop manual has a 'registration' of the communication ID between the ECM and the transponder ECU, which I followed and thought I had success with - looks like maybe not. I have read on Lexus forums that this worked for an ISF engine swap into a IS350.

Going to try a few things to troubleshoot first, but may end up with a TechStream VCI cable and a 2 day subscription. Have to see if the 2 day will do a VIN registration or immobilizer tweaking.

-- Adam
ArmstrongRacingSan Diego · Apr 29, 2018#40
If your using an IM ECM than you have no choice but to go through the immobilizer registration process. There is no way to bypass that I know of that will work with an IMM ECM
CrankyOldManWest Michigan · Apr 29, 2018#41
You're definitely into uncharted territory from our standpoint. If your ECU requires an immobilizer to work, then you have to find a way to make them happy together.

Where the hell is CTScott when you need him??
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#42
Hey Tom, thanks for the tidbit. Do you mean the DLC3 jumper registration as described in the workshop manual or a TechStream registration..?

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#43
Hmmm... so pin pull is strictly for an immobilzer car with a non-immobilzer system only? Thought with a bypass there was a clever way to trick the ECM into thinking it had a legit signal.

Maybe Scott will see the thread and jump in with some ideas. 😁

-- Adam
ArmstrongRacingSan Diego · Apr 29, 2018#44
Originally Posted by atomic_hoji ↑
Hey Tom, thanks for the tidbit. Do you mean the DLC3 jumper registration as described in the workshop manual or a TechStream registration..?

-- Adam
At first I didn’t think the DLC method would work at all, but if your engine ran for 15 seconds it must have worked on some level. I say this because every single ECM swap I’ve done, the engine fires up for maybe 2-3 seconds and dies. After that it will only crank and never run again until you disconnect the battery.

The only fix I’ve ever seen was to bypass the IM module if you have a non-IM ECM, or to register completely via the dealership process. I’ve hear of people getting the donor cars IM module and key to make it work as well.

Another thing to consider is those guys that come and cut keys for you, I’ve heard they have a way to register keys.
atomic_hojiThread starterKincardine, ON, Canada · Apr 29, 2018#45
I figure I'll give it a try again tomorrow and see if maybe disconnecting the battery right after knackered it..

Because the engine was from a wrecker I don't think I could get the transponder ECU, but I'll give them a shout in case it was saved.

Good call on the mobile lock and key, may be able to make the link if they have TechStream Security access.. Have to make some calls.

-- Adam
atomic_hojiThread starterKincardine, ON, Canada · Apr 30, 2018#46
Had a tinker this morning and..


It's

ALIVE

...

for real! 😲

Just posting up excitement at the moment, but she ran for about 30s while I checked belts, etc.. and she stinks bad - exhaust leak at the manifold to downpipe because the xD exhaust doesn't mate with the hangers on the Yaris.. BUT, sits and idles OK.

Having a tasty beverage and heading out to run errands, pick-up kids from school, etc.. will plug away more soon.

-- Adam
tmontagueCaledonia Ont. · Apr 30, 2018#47
Congrats buddy!
ArmstrongRacingSan Diego · Apr 30, 2018#48
OMG shit just got REAL!!!!

Congrats dude and great work!!!

Now, what fixed it? Lol
atomic_hojiThread starterKincardine, ON, Canada · May 1, 2018#49
Thanks guys! 👍

Sorry on the delay - executive decision with nice weather to get some other things finished yesterday; poor truck must feel for attention, everything is breaking - rear caliper hung-up (fixed now), exhaust literally broke in two so the muffler is dangling, front half-shaft inner CV is sloppy and clunks around, and since I put the mud terrain summer tires back on the steering is like a battletank.. seriously, vehicle jealousy must be real. 😲

...

The short version is - FUEL! I'll put my long-winded troubleshooting below, but basically the solution was to 'jumper' the fuel pump to turn on with the ignition signal (IGN). The technical explanation and and how to implement the solution is as follows:

On the Yaris pin-21 on A72 (small ECM connector) is for fuel pump control (FPC). When the ECM detects crankshaft rotation, it puts a signal to pin-21 to provide a ground. This provides power to the C/OPN relay coil in the main engine junction box (JB), closing the relay switch which provides power from the EFI Main circuit to the fuel pump; fuel pump runs steady as long as the car is running.

In the iM, pin-21 on A72 is also FPC, but it works differently. When the ECM detects a need for fuel it outputs a control signal to a separate fuel pump control ECM which in turn controls the fuel pump; apparently a variable speed pump. So, at low fuel, i.e. idle, low signal, but when you hit the throttle it needs more fuel, signal increases.

Before the modification, the iM ECM was basically being incorrectly used as a ground as the circuit expected from the stock Yaris ECM. It was likely working when I first fired it up as idle would have a very low fuel demand, but as the signal varied at pin-21 (I touched the throttle) I believe it was causing the C/OPN relay coil to chatter or de-energize, cutting the fuel pump and stalling. This seems to jive as the latter times I was trying to start it I was pushing the throttle in part way thinking it would help it rev and avoid stalling and it was stalling out more quickly - hence thinking < 3s the immobilizer was killing it.

WARNING - this solution bypasses ECM control of the fuel pump! The factory ECM is designed to shut off the fuel pump in the event of an accident. If you do not, or are unable to, turn the ignition off in the event of an accident there is an increased risk of injury or death due to fuel system fire.

Intense, but seriously, it bypasses a safety feature - always be careful, and understand what you've changed and how it impacts the vehicle.. 👍

To jumper the fuel pump to the IGN signal remove the upper half of the main engine JB, disconnect connector 1E from the bottom side of the integrated relay assembly (skinny white rectangle), and pop out pin-11 (violet). Blank the pin as it will still have a live signal from the ECM with heat shrink and/or electrical tape. From a spare harness, I grabbed a matching terminal with a length of wire, inserted the new terminal into pin-11, and ran the loose end to a body ground connection. Alternatively you can cut the violet wire leaving a pigtail and solder/crimp to existing terminal, then run to body ground. What this does is put a permanent ground on the C/OPN relay coil which, since the relay coil is only provided power when the IGN relay is energized (key to ON), it won't have power when the car is off but once the key hits ON it will energize and start the fuel pump.

...

Basically, as much as the way it was behaving seemed like the immobilizer had me beat I couldn't explain why I had it fire up for the first 15s the first try. I was willing to accept maybe a fluke, but I would have sworn I had a ~6s run as well; wasn't counting so could have been wrong. It was Tom's comment about how the immobilizer would let it fire and die in 2-3s and then just crank, i.e. no combustion, that I thought some further troubleshooting was worthwhile as I each time I was getting combustion; it was just short lived and the engine literally shuddered and stalled out. There was buzzing/whine from the throttle body assembly and what I thought was the vacuum canister pump (which turned out to be the fuel pump) noises that I didn't understand either. So, I decided to run through the basics: air, fuel, spark.

Air seemed like a possibility as the throttle body was making noise and the MAF sensor was a cheap Chinese purchase. I randown the MAF and drive-by-wire electrical drawings and they seemed fine as I had recalled. My solder isn't perfect, so checked the voltage at the MAF and it was fine. Pushed the throttle pedal and checked the throttle body was responding and it was. I looked up the on-vehicle checks for each and they were easy enough to check and put them on the list. Nothing obviously outstanding that was telling me air was likely the problem.

Fuel was in the rail and getting into cylinders as I had combustion, but wasn't sustained. I reviewed the electrical drawings and came across the difference in the Yaris and the iM fuel pump control - which shouldn't have surprised me given the more complicated cooling fan control setup on the iM vs. the simple relay setup on the Yaris! I suspect with all the flipping back and forth of drawings when I made my original notes way back in the Fall I either missed it or accidentally looked at the same drawing for both and concluded they were the same - I caught myself on that once or twice; too many windows open at once is a setup for confusion! lol After digging into the SFI troubleshooting sections of each workshop manual and understanding better I was pretty convinced fuel was the problem - in running my start attempts through my head again it made sense that it was cutting sooner as each try I was pushing throttle in to get it to rev and avoid stalling. So, I jumpered the fuel pump to the battery before I connected anything and verified that the sound I was hearing was the fuel pump - it was - and then spent some time figuring out how to make the above solution to make the fuel pump circuit in the Yaris work with the iM FPC output. Tried it again and off to the races! (Then posted in excitement.. lol)

Never got to spark, which was pretty low suspect because it had been firing and when it was at idle the short time it was behaving.

...

More assembly today after work - got the interior, cowl, wiper etc.. all installed. The Injen cold air intake (CAI) just doesn't fit, so I can't get the LH headlight and bumper re-installed. I'll get the hood on and roll the car outside so I can pull the metal working stuff out and fab ECM brackets next. Once it's in place and final electrical routing and tidy-up is done I'll have to have a hack at the Injen CAI for fitment. Then: test drive.

-- Adam
ArmstrongRacingSan Diego · May 2, 2018#50
This is so awesome. You need to make a thread about the immobilizer registration process too, because you just proved we can use IM ECM’s.

That means every engine including a tC swap is now on the table!