Yarisworld Archive

Another Build Thread

26 posts · 15,861 views

heeroyuy01195Original postFlorida · Jun 7, 2017#1
Been a long time since I've been active on here. Even when I was on here frequently, I did more reading than posting. It's time to start reworking the Yaris so I figured I would start a thread to monitor the progress and so I have a reference of sorts. Can't find any pictures of when I first got the car back in 06' (I got one of the first ones on the lot😁) but here's one from around 09' when I had it on...I think they were Progressive or Progress? Something of the sorts, 2.5" drop all around and some old Racing Harts I "borrowed" from my brother.
Picture not included in this copy

Fast forward to around 2012
Picture not included in this copy
At this point, the car had been in 2 accidents, first I ran over a curb to avoid a car that ran the intersection and bent my rim and torsion beam. My torsion beam on the driver's side now has a permanent -1.5 degree camber that I corrected with shims. Had the wheels repaired and told the shop respray them back the original bronze...he gave me gold...👎 Then I switched to Megan coilovers and added a DIY garden edge lip. Around 2014 I hydroplaned on the highway and hit one of those water barrel barricardes and caved in my passenger side quarter panel. Had that replaced and fitted a new garden lip. Can't find the pictures unfortunately

Fast forward again to late 2016 and I had installed a modified EK Civic type R lip. Unfortunately I don't have any pictures of the car with the lip for some reason but early this year I had this happen...
Picture not included in this copy

Basically, the construction workers rerouted traffic late at night (none of the street lights were working yet so it was fairly dark) and, in their infinite wisdom, rerouted the traffic into a section of road that wasn't completed yet. That unfinished road used to be a median so I ended up on top of the median and hit a chunk of it on the way off which bent my sub frame and driver's side control arm. Also wrecked the radiator support on that side.

Did some work on it a few weeks later to at least get it "legal" to drive so I could get it to my work shop.
Picture not included in this copy
Picture not included in this copy

JDM bumper Fastener...adds anout 50whp...
Picture not included in this copy

Good as new! Well...sort of...
Picture not included in this copy

Made an attempt to swap out the damaged parts a few weeks ago but couldn't figure out how to disconnect the steering rack. Saw a thread that it's done from inside the car so I'll take another shot at it once the rain stops. Been raining here for about 2 weeks straight...

Replies 25

Steve35Vancouver, Wa. · Jun 7, 2017#2
could you post a closer pic of your "DIY garden edge lip". Or where did you get it Home Depot Lowe's etc?

Steve
DiCaprioGermany · Jun 8, 2017#3
My cars has a few scratches too, but i figured it's nothing mechanical and my car isn't a showcar. So instead of fixing it i'm going full JDM with the cable ties :D
heeroyuy01195Thread starterFlorida · Jun 8, 2017#4
Originally Posted by Steve35 ↑
could you post a closer pic of your "DIY garden edge lip". Or where did you get it Home Depot Lowe's etc?

Steve
Unfortunately I don't have any close up pictures of it. It's just the generic garden edging you get at any hardware store. It does flex a lot, especially on the highway, I was going to reinforce it but ended up swapping to a different lip. If I did it again I would double up the garden edging so it has some more rigidity. Thing folds over at highway speeds.

Originally Posted by DiCaprio ↑
My cars has a few scratches too, but i figured it's nothing mechanical and my car isn't a showcar. So instead of fixing it i'm going full JDM with the cable ties :D
JDM cable ties fix everything! My bumper was actually in good shape until that last accident. I pretty much ran over my bumper; when I hit the subframe it knocked the bumper off.
Steve35Vancouver, Wa. · Jun 8, 2017#6
Thanks guys!

Steve
heeroyuy01195Thread starterFlorida · Jun 8, 2017#7
That install is a lot nicer than what I did. I drilled holes and did zipties in a cross pattern along the lip.
heeroyuy01195Thread starterFlorida · Jun 17, 2017#8
Did some repairs on the Yaris today. Morning started out with this...

Picture not included in this copy


Got the car up on stands
Picture not included in this copy

Had to kick the MR2 and the 400 out of the garage temporarily
Picture not included in this copy

Started tearing stuff apart
Picture not included in this copy

And the damage...
Picture not included in this copy

Subframe dropped, thanks everyone for all of the advice on removing this!
Picture not included in this copy

Parts swapped, forgot to take a picture after the inner and outer tie rods were installed
Picture not included in this copy

So my second hand subframe had the rear mount still in it. Looks way different from mine. Curious if it was actually a LB subframe. Either way, subframe went on the car with no issues.
Picture not included in this copy

Reassembly, installed new OEM headlights and a few other bits that broke after the accident.
Picture not included in this copy

Lower grill was falling off so I cut it out so it would stop flopping around while I drive. New bumper on the way so this is temporary. Also installed some winjet fog lights as I couldn't get hold of an OEM set when I was ordering parts.
Picture not included in this copy

Back on the ground with his brother
Picture not included in this copy

Need to get the car aligned but that'll have to wait until next Saturday. Next on the list is to get the paint issue sorted and install the new front bumper when it gets here.
DabuuNo Bueno Park, CA · Jun 17, 2017#9
Good work man. Enjoying the thread!

Nice adub by the way.
kimonaHuntington Bch, CA · Jun 18, 2017#10
Major work... and fast! Way to go, mate.
heeroyuy01195Thread starterFlorida · Jun 18, 2017#11
Thanks guys :) having trouble finding an alignment shop that'll take my car. Apparently it's too low to fit on the alignment racks around me. My usual alignment place changed owners and they're not nice people now...
DabuuNo Bueno Park, CA · Jun 22, 2017#12
Low car problems. :(

Also, didn't realize this till now, but, sick gundam wing reference.
heeroyuy01195Thread starterFlorida · Jun 22, 2017#13
Thanks mate, was obsessed with gundam wing when I was younger haha. My VW friend recommended a place near by. His car is ridiculously low so they should have no problem taking my car in. Can't wait to get started on the cosmetics, thing desperately needs some paint!
heeroyuy01195Thread starterFlorida · Jun 26, 2017#14
Quick Update, spent most of Saturday Morning looking for an alignment shop that would take my car in. The place my friend with a slammed VW recommended refused to work on my car so I just stopped at every shop I saw on the way home. As luck would have it, the place 5 minutes from my house was the only one willing to do the alignment. Anyhow, car is finally drive-able and it felt good to finally be able to throw the thing around some corners. Still not 100% road worthy yet; at least not to my standards. Need to install new fender liners which should be getting here this week and take care of a few other odds and ends.

Second note, was able to get a hold of CTScott (he's traveling out of the country frequently due to work, just in case anyone was trying to get a hold of him. He will reply but it takes him a while; just be patient 🙂) and I got an airbag module from him. Going to be installing some Recaros later using blacksandiegovitz's old seat brackets and sliders I picked up when he parted out a few years ago. Also snagged a SSK from Garm that he had on his ebay page:
Picture not included in this copy

Also have a few other things coming in the mail, I'll post up pictures once they get here 😁
heeroyuy01195Thread starterFlorida · Jul 1, 2017#15
Made some more progress on the car this week. Installed:

Front Fender Liners
Rear Wiper Delete Kit
Mud Guards
Micro Image SSK

The fender liners were the cheapest ones I could find on Rock Auto, I normally stick with all OEM parts but if it's what I consider a "wear item" then I don't want to spend too much on something I'm going to be replacing frequently. The Mud Guards I picked up on Amazon for I think $10 or so, have a brand new OEM set but after thinking about it, mud guards are wear items so I'll save the OEM ones for later. The rear wiper delete I bought from password JDM, I never use my rear wiper and the plastic trim was cracking something nasty so I figured I would just take it out. Picked up the SSK from Garm's ebay store, I think he has a few left if anyone is looking for one. Pictures time...

Rear Wiper Delete
Picture not included in this copy

Installed
Picture not included in this copy

How the Blueberry is looking now
Picture not included in this copy

MI SSK
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I realized after I took this picture that on that I forgot the washer that goes on top of the cable. The washer is on there but I forgot to take another picture.


Followed this thread back when it first started and read through it again recently before installing
Micro Image Short Shift Kit- prototype review

I didn't find the install to be as difficult as some of the other members made it out to be. Was actually quite simple and I finished it in about 30 minutes or so. In terms of performance, I've only put a few miles on the car since the install and it was still super notchy. It seems to be getting smoother the more I shift/drive around. Guessing the cables just need to reposition themselves a bit. The throw is just as short as with the old NST I had in there but I'll see if the notchyness eases up after I drive the car a bit more.
heeroyuy01195Thread starterFlorida · Jun 22, 2019#16
Wow I can't believe it's been two years since I made any drastic changes to the car. Time sure does fly! Anywho, Fortune Auto coilovers installed and I picked up a few other things...

Joined the CF club
Picture not included in this copy

Picture not included in this copy

Also made a new front lip. Last one got destroyed on the highway.
Picture not included in this copy

Next on the list is to finally paint and install my spoiler; been sitting on this thing for about 5 years 😆 Have a Speedhut tach on the way that will be going in as well. Also looking into getting the transmission rebuilt and install an LSD. Looking for a TRD helical type but we'll see what money permits and what happens to pop up when it's time. After that it's 2zr parts gathering. So far all I have is an ECU, courtesy of frogger. Ultimate goal is to build a reliable and fun daily driver.

Unrelated question, can anyone recommend a better picture hosting site? Photobucket is really crappy now...
LeegamerAshland, VA · Jun 24, 2019#17
Looking good!
myfirstyotaToronto Canada · Aug 19, 2019#18
Any insight as to where your new front lip came from?

Imgur sucks now too...
06YarisRSFredericton, New Brunswick, Canada · Aug 19, 2019#19
Originally Posted by myfirstyota ↑
Any insight as to where your new front lip came from?

Imgur sucks now too...
I may be wrong, but it looks like a 2000ish Civic lip.
heeroyuy01195Thread starterFlorida · Aug 19, 2019#20
Originally Posted by 06YarisRS ↑
I may be wrong, but it looks like a 2000ish Civic lip.
Yep it's a modified 2000 Civic lip. Just looked for the cheapest lip I could find on eBay. My car gets battered on the highway so I go through lips often.
myfirstyotaToronto Canada · Aug 20, 2019#21
Any major modifications to get installed?
Fitment looks decent in the pic... it's decent in person?
heeroyuy01195Thread starterFlorida · Aug 20, 2019#22
Originally Posted by myfirstyota ↑
Any major modifications to get installed?
Fitment looks decent in the pic... it's decent in person?
Yeah there's a decent amount of cutting, heating, bending, etc. involved in getting it on but it's nothing too difficult. Any urethane lip will work, I used an EG Civic lip before this one because it was cheaper at the time. As for fitment, it really comes down to how much time you have to put into it.

In a nutshell, trim the top that normally screws into the civic bumper and then get a heat gun and start bending it to the shape of your bumper. Grab a few self tapping screws to hold it on and you're done. If you plan it out right, you can screw it into the bumper from the bottom so you don't see any of them. I was short on time with this one so I just screwed the lip onto the bumper from the front and sides. Not noticeable from afar because they're black but you can see them for sure if you're looking for them. 👎

If you look at my car up close it's far from perfect but my bumper is also mangled from an accident so I didn't put too much effort into making the lip fit absolutely perfectly to my imperfect bumper. Also, I go through these things every few months with all the construction on the highway so I don't invest too much time or money into any lip I make. I look at these as throw-away items since it's on the bottom of the car and gets smacked into everything so I never spend more than $20 on a lip 🤷

If you want a way easier option, garden edging works nicely and looks decent. Only issue I had with it, when I single layered it, it would flex on the highway. Put some backing on it for rigidity and it's good to go. I use the 4" tall version with the sort of rounded bump edge. Heat it up then flip it upside down so the part that goes in the ground is screwed or zip tied to the underside of the bumper. Way less cutting and easier to mold to the bumper. Don't think I have any pictures of this one if it's not in the thread; sorry. Anyways hope this helps!
06YarisRSFredericton, New Brunswick, Canada · Aug 20, 2019#23
How did you handle the ends of the lip? Since the civic lip is a lot longer than the Yaris front, I had to shorten the two ends and cap them.
myfirstyotaToronto Canada · Aug 21, 2019#24
Sure does help. Thanks heeroyuy
heeroyuy01195Thread starterFlorida · Aug 22, 2019#25
Originally Posted by 06YarisRS ↑
How did you handle the ends of the lip? Since the civic lip is a lot longer than the Yaris front, I had to shorten the two ends and cap them.
I cut the lip down to fit. On my first one I reused the ends I cut off and blended them back onto the lip but it took a lot of time to get it right. After the first one got destroyed I didn't bother going through the hassle since it's only a matter of time before I break the replacement. The highways around me are always under construction so my bumper gets beat up quite a bit. 👎

Originally Posted by myfirstyota ↑
Sure does help. Thanks heeroyuy
No problem, glad I could help. Really like your build thread, hoping to swap to a 2zr next year as well. 🤘
myfirstyotaToronto Canada · Aug 23, 2019#26
Do it! That car has to be one of the most fun cars ive ever driven.