Yarisworld Archive

Garage Door Bottom Seal "Front Spoiler"

25 posts · 14,675 views

derickveliz2Original postCentral, MA · Apr 2, 2012#1
I was inspired (again) with Kaotic's ride I got this garage door bottom seal on sale for $4.50 got some other parts for $15.00 and spent like 2 1/2 hours under the car, came out great!

Ok, now anything 4.5" and above I go around!


D.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy



This one with some Infrared-film effect! (looks like a black yaris)

Picture not included in this copy




Some of the Twisty back roads of New England near home.

Picture not included in this copy


D.

Replies 24

jpmck03USA · Apr 2, 2012#2
Originally Posted by derickveliz2 ↑
I was inspired (again) with Kaotic's ride I got this garage door bottom seal on sale for $4.50 got some other parts for $15.00 and spent like 2 1/2 hours under the car, came out great!

...

Picture not included in this copy
Holy shizznits, that's a lotta screws and washers!

But, it looks good! Being a perfectionist pays off!
derickveliz2Thread starterCentral, MA · Apr 2, 2012#3
Originally Posted by jpmck03 ↑
Holy shizznits, that's a lotta screws and washers!

But, it looks good! Being a perfectionist pays off!
No perfectionist... patience! Thanks 👍

D.
derickveliz2Thread starterCentral, MA · Apr 2, 2012#4
Originally Posted by jpmck03 ↑
Holy shizznits, that's a lotta screws and washers!

But, it looks good! Being a perfectionist pays off!
Originally Posted by TOLMACH ↑
Looking great, Derick

Question: how does it affect the sound stage and imaging? 👍 😉
Thanks Tol. 😁

Mmm...

Less wind under the car
at high speed! less road noise (O: I guess LOL 👍

D.
jpmck03USA · Apr 2, 2012#5
Originally Posted by derickveliz2 ↑
No perfectionist... patience! Thanks 👍

D.
Well, you might not be a perfectionist... but it looks like it's perfectly applied to your bumper... 👏
kimonaHuntington Bch, CA · Apr 2, 2012#6
Excellent job. Looks great!
catliektheifLeesburg, VA · Apr 2, 2012#7
hd lip, lovin it 👍
Klink10910 · Apr 2, 2012#8
Very clean looking.
derickveliz2Thread starterCentral, MA · Apr 2, 2012#9
Originally Posted by kimona ↑
Excellent job. Looks great!
Thank you,



Originally Posted by catliektheif ↑
hd lip, lovin it 👍
Me too, lets see how much will stand... (O:



Originally Posted by Klink10 ↑
Very clean looking.
Came out good thanks, I hope I can keep it clean!



Originally Posted by jpmck03 ↑
Well, you might not be a perfectionist... but it looks like it's perfectly applied to your bumper... 👏
I did what Kaotic recommended me to do, maybe overkill but I hope I can keep it until next winter.

D.
403RSCalgary, Canada · Apr 2, 2012#10
Damn that looks sharp!
Kaotic LazagnaCentral Valley, CA · Apr 3, 2012#11
Love it. I like your choice of washers too. I didn't measure mine, and mine are actually too big in diameter, which is why mine is wavy in some parts. Good job! 👍
3cyltrboOttawa · Apr 3, 2012#12
can you give some info on spacing between screws ? / washer size / washers on front and back of screws etc......

Cheers

Will
1.5Tampa · Apr 3, 2012#13
Looking good.
Kaotic LazagnaCentral Valley, CA · Apr 3, 2012#14
Originally Posted by 3cyltrbo ↑
can you give some info on spacing between screws ? / washer size / washers on front and back of screws etc......

Cheers

Will
For me, I used self tapping screws. 1.5" long screws would be good enough. As for washers, I'd just compare it to the surface of the bottom seal that you are going to buy as each brand may be different. I, as well as Derick (I think), used extra strength double sided tape. Mine has held up for a few years and quite a bit of nasty driveways and speed bumps.

Spacing should 3-4".
fnkngrvIn The Hotbox · Apr 3, 2012#15
it might sound silly, but it might not be a bad idea for the rear as well just for extra protection? I know that once my exhaust is routed through my rear bumper I will want to protect the bottom of it on backing up.
Kaotic LazagnaCentral Valley, CA · Apr 4, 2012#16
You can give it a try. Not sure how that would look. I've seen people use these as side skirts too, and those don't look right.
fnkngrvIn The Hotbox · Apr 4, 2012#17
I am supposin it would def have to be the right aestetics to work.
Kaotic LazagnaCentral Valley, CA · Apr 4, 2012#18
lol
derickveliz2Thread starterCentral, MA · Apr 6, 2012#19
Originally Posted by 3cyltrbo ↑
can you give some info on spacing between screws ? / washer size / washers on front and back of screws etc......

Cheers

Will

Well, spacing was about 3 inches + 3M Scotch 5lb Exterior Heavy-Duty Mounting Tape.




The Rubber:

Picture not included in this copy


And the Mechanical power:

Picture not included in this copy

Picture not included in this copy


D.
ciscobearBarbados · Apr 6, 2012#20
Love the work Derick. I just wanna recommend a product that I have fallen in love with. In the pics the black plastic by the mirrors are a little faded and I've used this product to get it sorted. Keep up the good work.

Picture not included in this copy
jpmck03USA · Apr 6, 2012#21
Originally Posted by derickveliz2 ↑
...3M Scotch 5lb Exterior Heavy-Duty Mounting Tape...
Thanks for listing the brand and type of mounting tape!

I've read through a number of these Home Depot lip threads and everyone seems to just give a vague "I used mounting tape" to describe what they used!

If I ever get around to doing this, at least I'll know what to look for!

👍
derickveliz2Thread starterCentral, MA · Apr 7, 2012#22
Originally Posted by ciscobear ↑
Love the work Derick. I just wanna recommend a product that I have fallen in love with. In the pics the black plastic by the mirrors are a little faded and I've used this product to get it sorted. Keep up the good work.

That's a good eye! thank you so much I've been trying different stuff but after a while it just fades back, I'm going to give it a try! 👍


D.
derickveliz2Thread starterCentral, MA · Apr 7, 2012#23
Originally Posted by jpmck03 ↑
Thanks for listing the brand and type of mounting tape!

I've read through a number of these Home Depot lip threads and everyone seems to just give a vague "I used mounting tape" to describe what they used!

If I ever get around to doing this, at least I'll know what to look for!

👍

You are welcome, actually I did use 2 kinds but I bet they where the same stuff, I was lazy to pick up from the trash can and take a picture of the second kind of tape, this one I got at Home Depot... and it does say 3M at the bottom.

Picture not included in this copy



D.
derickveliz2Thread starterCentral, MA · Apr 7, 2012#24
Now I was very curious to see how much deflection of the lip at high way speeds, this shot was taken at 65 mph and it's not bad...


Picture not included in this copy


D.
Kaotic LazagnaCentral Valley, CA · Apr 8, 2012#25
With that locking washers, that's really not coming off unless it tears. lol. Great job.