brushforhireOriginal postJohnstown, PA · Feb 21, 2016#1I've been wanting to do this swap for awhile. I planned on doing it back in July of last year, but then my '00 tundra rear axle started leaking, so i had to fix that first instead. I bought a welder and learned to weld and fixed it myself instead of paying someone to do it. Well I had planned on doing this maybe later in the year, but then my exhaust decided to convert itself to a side dump system. So instead of fixing this exhaust only to redo it later when I did swap, is a pain to me. So here I am. Along with the swap, I am doing the Xd front caliper swap, and probably Megan coilovers at the same time. My front brakes are totally shot, and I am pretty sure my rear suspension is bad.
So here are my pics and documentation of how I am doing the swap.
Picture not included in this copy The car, and my hobart 210 welder I will be using for the exhaust work.
Picture not included in this copy I started by removing the hood
Picture not included in this copy And then the front bumper
Picture not included in this copy The rebar and front headlights were removed, along with various other small part.
Picture not included in this copy Here I have removed the a/c condensor, rad, and rad support. I have also taken out the ECU, battery tray, air box, etc. I think I have most all the connectors disconnected at this point to remove the engine harness as one unit with the engine.
I also took off the front brakes today. The fender liners, and under shields were also removed. I plan on taking the fenders off so I can put some sound deadening material on the backside of them.
I am taking this opportunity to clean the engine bay and possibly spray it gloss black while everything is out.
I am contemplating swapping in the Xd brake master cylinder, while I can actually get to it. I am planning putting an optima yellow top battery inside the car to free up some engine bay space and help with front to back weight balance.
I want the extra space because I hope to turbo this swap someday, and I want to do as much as I can now to prep for it.
So here are few pics of the Yaris S front rotors, Xd front Calipers and brackets. I am using G2 caliper paint on them. Decided to just go gloss black, because I have no idea what color my exterior might end up being, not to mention, I do like the sleeper look. Nice without drawing to much attention.
Picture not included in this copy Picture not included in this copy Picture not included in this copy For tools I am using a mechanic set of sockets and ratchets I bought from Sears, a Ryobi 1/2 impact One+ gun, Kobalt impact sockets from Lowes, floor jack, jack stands, and assorted other pliers and small hand tools. I will try to keep the tool list updated as I go to let everyone know what it takes to do this.
8 attachments not included in this copy
Replies 131
Frank the TankToronto · Feb 21, 2016#2so what parts are you using?
does this car have abs?
tmontagueCaledonia Ont. · Feb 21, 2016#3Damn these builds just make me drive my 1nz harder and make me feel less guilty about it...
brushforhireThread starterJohnstown, PA · Feb 21, 2016#4 Originally Posted by
Frank the Tank ↑ so what parts are you using?
does this car have abs?
I am using a scion Xd engine, harness, ecu, alt, a/c compressor, etc. Not totally sure what year yet. All the stuff has only 65k on it. Everything is from the same vehicle except the a/c compressor.
According to Armstrongracing's thread, the needed parts are:
1)2ZRFE engine with ALL components and accessories from a 2009+ Xd, Corolla
2)ECM from a 2008-2009 Xd applicable to your car in auto or manual trans
3)Xd engine harness also applicable to your car and transmission choice.
4)Xd RH engine mount and bracket
5)Xd exhaust midpipe
6)Xd intake AND MAF sensor
7)Xd a/c compressor lines - I did not need these. I was able to reuse my old lines.
8)Mini-add-a-circuit (for the MAF sensor, it has different wiring and needs this. Thank you for the correction Armstrongracing).
In PA they can't sell used cats without them being re-certified, which isn't worth the money. So I asked them cut off the top of the exhaust pipe, so I could use the flange and weld a new exhaust to it.
I do have ABS
Frank the TankToronto · Feb 21, 2016#5Will this be a manual transmission?
brushforhireThread starterJohnstown, PA · Feb 21, 2016#6Keeping it auto for now.
junorico24Sydney · Feb 21, 2016#7Wow,first hatch with a 2zrfe? sexy..
ilikericesavannah, ga · Feb 22, 2016#8RagnaCat was the first 3dr hatch to do this swap about 2 years ago I believe. Had a build thread on microimage forums, but lost all that useful info..
ArmstrongRacingSan Diego · Feb 22, 2016#98)Mini-add-a-circuit....
This is required on any 2zr swap due to the fuse box differences. The 2zr mini MAF sensor has different wiring than the older gen MAF sensor
brushforhireThread starterJohnstown, PA · Feb 23, 2016#10Not to much progress right now. Bought a 2 ton engine crane and had to assemble that. Also bought some more can lights for my garage ceiling so I can actually see. Most of my time working on this is usually an hour before work, and about an hour after.
I also decided to take the cowl off to make it easier to work in there.
I am at the point that all I really should need to do is, pop out both axles, and then disconnect the manifold from the downpipe and it should come out after I unbolt the mounts.
I did notice that my manifold to downpipe bolts are really rotted, one the springs is missing, and the other bolt head is rotted away with the spring hanging on by a hair. That looks like it is gonna suck to get at. Gonna try and squeeze my sawzaw in there and just cut them off.
tmontagueCaledonia Ont. · Feb 23, 2016#11Does anyone know if you can just buy the xD downpipe flange separately? I have a 2.25" custom echaust and it would make more sense to just weld the flange onto my exhaust so that it matches up to the xD header. Save money and keep the performance.
brushforhireThread starterJohnstown, PA · Feb 23, 2016#12This might be a good place to start:
Universal 2.25" ball flange Here is another I found, when I was looking into this myself:
Flange I did find a couple other, but all pretty much the same stuff. Not totally sure of the size needed, but for some reason I was thinking 2.25"
ArmstrongRacingSan Diego · Feb 23, 2016#13That may work. But if you're going completely custom, buy the RPM headers for max flow. They sell a cated midpipe if you want also
tmontagueCaledonia Ont. · Feb 23, 2016#14The 2.25" flange would fit my exhaust but the question is would that mate up to the donut gasket on the xD header?
Although the rpm header and catted mid pipe would be the best since there'd be no question of compatability. The other option would be to just go to a junk yard and cut off the flange on a corolla. Then weld that onto the custom mid pipe. I'm sure the rpm header and mid pipe are pricey
brushforhireThread starterJohnstown, PA · Feb 23, 2016#15 Originally Posted by
tmontague ↑ The 2.25" flange would fit my exhaust but the question is would that mate up to the donut gasket on the xD header?
Although the rpm header and catted mid pipe would be the best since there'd be no question of compatability. The other option would be to just go to a junk yard and cut off the flange on a corolla. Then weld that onto the custom mid pipe. I'm sure the rpm header and mid pipe are pricey
Someone posted a review of the Walker universal one and said that it worked perfect on their 2013 Corolla. So that may help.
The RPM setup with header and midpipe with cat and resonator is $725. I am really thinking about it, but my welder is just sitting there begging to be used also. I may just do a temporary setup to get back on the road and then take my time designing a proper exhaust.
tmontagueCaledonia Ont. · Feb 23, 2016#16Good to know, thanks for the info. yikes $725, mind you that's with a header as well
CrankyOldManWest Michigan · Feb 23, 2016#17I'm kind of stuck on the exhaust as well--I'd love to get the RPM long-tube kit, but it's pricey and doesn't include the axle-back. I've got a resonator-back mandrel bent tube that MalibuGuy made to order, but that doesn't help me to get from the resonator to the header (where all the expensive bits are).
An aftermarket doesn't seem to be much cheaper than a used OEM--both are around $550--and that still doesn't cover the header or axle-back. Decisions, decisions!
tmontagueCaledonia Ont. · Feb 23, 2016#18where are you guys finding the rpm package listed? I'm struggling to find the proper set up on line anywhere
brushforhireThread starterJohnstown, PA · Feb 23, 2016#19 Originally Posted by
tmontague ↑ where are you guys finding the rpm package listed? I'm struggling to find the proper set up on line anywhere
You can find the Scion XD RPM setup here:
fastscions.
The only make it for the 2zrfe, if you were searching for the 1nzfe, that might be why you are having trouble finding it.
I got the axles popped out, but left them in the knuckles because the axle nuts were so rusted up. I have the struts off, so at least they have a bit of wiggle room.
So all I gotta do is unhook the fuel rail connector, and undo the three mounts and I should be good to take the engine out.
I am planning to lift it by the outer two mounts.
I removed the lower tie bar also for more room.
I am thinking I just might fab up a midpipe myself. I am so torn, I was kicking around getting the OBX catless system and welding in a new flange and cat, but it is stainless, and I don't know how tricky stainless to mild steel would be to weld.
tmontagueCaledonia Ont. · Feb 23, 2016#20spray the crap out of the axle nuts with some PB Blaser a few times each day. Then when everything is back installed used a massive breaker bar or preferably an air gun. Better to spend the time now and release them before it becomes too late and you can't when you need to.
When I installed my rear axle spacers the hubs needed to be air chiseled off. It was a huge pain but I was glad I did it. After re installing with proper anti seize when ever I needed to change my rear hub I can do so relatively easily.
The other option to pull the engine is to go to the dealership and get the 2 engine hoise hooks with 1 bolt each that mounts into the front passenger side and rear drivers side of the engine. However, you way should also work fine, the engine is light.
brushforhireThread starterJohnstown, PA · Feb 24, 2016#21Woot! Engine and trans came out this morning.
Received the engine and most of the parts today at work. In the truck waiting to get unloaded. Still gotta collect a few oddball pieces and I will be good to go.
I went ahead and ordered a Takeda cold air intake, for this. Along with my Megan coilovers. Still kicking around what I want to do for the exhaust.
ArmstrongRacingSan Diego · Feb 24, 2016#22Awesome!!
beakerconyers ga · Feb 24, 2016#23 Originally Posted by
brushforhire ↑ Woot! Engine and trans came out this morning.
Received the engine and most of the parts today at work. In the truck waiting to get unloaded. Still gotta collect a few oddball pieces and I will be good to go.
I went ahead and ordered a Takeda cold air intake, for this. Along with my Megan coilovers. Still kicking around what I want to do for the exhaust.
I know it's pricey, but you have got to go with the RPM setup. Gotta see how much can be squeezed out of this motor.
👍
tmontagueCaledonia Ont. · Feb 24, 2016#24^i second that. The RPM exhaust is a beauty piece and I have a feeling it'll be good for some gains. Keep in mind the 2zr is going in an extremely light car meant for a weaker engine so even small gains will be felt pretty good.
I'm convinced when my engine start to burn oil in the next decade i'll be swapping in a used 2zr instead of re building and installing a Blitz s/c. As much fun as a boosted set up would be an additional 30 hp/tq all engine would be better
ArmstrongRacingSan Diego · Feb 25, 2016#25brushforhireThread starterJohnstown, PA · Feb 26, 2016#26Just a small update, the Takeda intake won't work because it reuses the factory MAF sensor tube, and I don't have that. This was not mentioned anywhere in the auction.
Ordered a flexplate from ebay, so that should hopefully be here soon.
CrankyOldManWest Michigan · Feb 26, 2016#27 Originally Posted by
brushforhire ↑ Just a small update, the Takeda intake won't work because it reuses the factory MAF sensor tube, and I don't have that. This was not mentioned anywhere in the auction.
Ordered a flexplate from ebay, so that should hopefully be here soon.
Sure enough, the pics on the aFe website show the OEM MAF tube in there. What a weird thing to do.
1 attachment not included in this copy
brushforhireThread starterJohnstown, PA · Feb 26, 2016#28Yeah, I didn't realize that it was the oem piece until I had it in my hands and realized they wanted you to reuse the stock piece. I would have expected better considering that it wasn't a cheapo intake. The seller is working with me to try and find me one though.
I get why they did it though, easier than trying to figure out the correct mounting and depth of the MAF. From what I was reading alot of the intakes don't mount the sensor at the correct depth and it throws codes. I noticed alot of the other intakes having a smaller section where it mounts to make up for this. Which seems weird to just have a bottle neck in there like that.
CrankyOldManWest Michigan · Feb 26, 2016#29The real bumer is that you can't find them cheap on eBay, and they're too new to be in you-pick-yards.
ArmstrongRacingSan Diego · Feb 26, 2016#30The cheapest stock airbox I found was $120....On Ebay
brushforhireThread starterJohnstown, PA · Feb 27, 2016#31The seller actually found a piece from another toytota for $39 shipped that looks almost exactly the same. They are refunding me $20, to help pay for it. So I will give it a shot and see what happens.
Either way I will keep you updated.
So I am waiting on the flexplate, that intake piece, and trying to figure out what I want to do for the exhaust. I am thinking I am just gonna pull the trigger on the RPM long tube setup. I have my welder, but by the time I piece out the cat, flex tube, flanges, o2 bung, resonator, etc. I will be probably over halfway there anyways.
In the meantime I'm gonna finish cleaning up the engine bay, and then probably just spray it all black.
I did get the passenger side axle out. The drivers side it probably gonna stay in. The end no longer even has threads, just rusted solid. The passenger side came out with relatively little effort, considering the miles on it.
I did notice alot of my bushing are looking rough. I am thinking it's time for whiteline bushing kit.
I will try and get some currect pics up later today.
ArmstrongRacingSan Diego · Feb 27, 2016#32Good work man!
brushforhireThread starterJohnstown, PA · Feb 28, 2016#33Okay well slow progress going on, and a bit of a surprise.
Here is the car in it's sorta current state:
Picture not included in this copy The wheel well:
Picture not included in this copy Working on cleaning as much as I can, I would like to spray it gloss black just to give it another coat and protect it a bit.
The surprise was that I actually managed to get the drivers side axle out.
The rusted mess:
Picture not included in this copy I didn't think there was anyway that nut was ever going to come off, but I kept messing with it. I actually tried to tighten it, and then hit it real quick in reverse and I started to come right off.
Picture not included in this copy This tool was some of the best money I ever invested:
Picture not included in this copy Ryobi one+ 1/2 impact. I have really worked it hard, and it just keeps going. I used it to take the rear end off of my 2000 tundra, and it plowed right through the rusty bolts and nuts there, too.
Some of the other tools I am using to do this job, just so people can see what it takes to do this:
Picture not included in this copy Picture not included in this copy The old engine and new engine:
Picture not included in this copy Picture not included in this copy I will be buying a tap and die kit to redo a number of the smaller 10mm bolts that snapped right off, trying to take them out.
It really is just basic tools that anyone should have, if they are considering doing this themselves.
So far this has been an interesting job, seeing as that I am doing it completely solo.
I was hoping to have this done in the next week, but I am gonna take my time and work on fixing the bushings and any other small stuff I find to save me from having to tear this stuff down again.
9 attachments not included in this copy
Frank the TankToronto · Feb 28, 2016#34How much was the engine lift? There's one at my work that hardly gets any use that maybe my boss can lend me when I get this going (which won't be for a while. Suspension, brakes and tires are first on the list)
ArmstrongRacingSan Diego · Feb 28, 2016#35Youre supposed to unbolt the torque converter from the flexplate, not pull it out of the trans. Haha. Otherwise good work!
brushforhireThread starterJohnstown, PA · Feb 28, 2016#36The engine lift ran me $180. I got it on sale at harbor freight. I like it because the front legs fold up for easier storage. It is the tow ton lift. The 1 ton lift is usually $180.
Originally Posted by
ArmstrongRacing ↑ Youre supposed to unbolt the torque converter from the flexplate, not pull it out of the trans. Haha. Otherwise good work!
LoL, I kinda wondered that after I got it apart.
For future reference I would unbolt the torque converter in the car, because it is a pain to get to the underside of the engine while hanging from the lift.
junorico24Sydney · Feb 28, 2016#37Nice..
Do you use the same engine mounts on the right side as the one in the Yaris? I'm guessing the driver side and underneath are the same because you're using the Yaris gearbox. Also I have a manual Yaris so i have to change the ecu and harness right? Sorry for the stupid questions.
brushforhireThread starterJohnstown, PA · Feb 29, 2016#38The right side engine mount is from a Scion XD. The middle rear and LH mounts are the same. For a manual, you would need the harness and ECU from a manual XD.
brushforhireThread starterJohnstown, PA · Feb 29, 2016#39I ordered the RPM header and midpipe. I finally caved. LoL
ArmstrongRacingSan Diego · Feb 29, 2016#40Haha awesome, I did too!
CrankyOldManWest Michigan · Feb 29, 2016#41I've got one on my wish list. I'm sure RPM and FastScions appreciate the surge in business!
brushforhireThread starterJohnstown, PA · Mar 1, 2016#42For sure. I did some digging and found a 5% off coupon code on their facebook page. "tax"
I had to order a few random parts while I am in there doing this. A RH rad support, and lower rad tie bar. Both a little bent from when I hit a snow bank. Not to noticeable, but it will drive me bananas knowing that they are bent.
Coilovers arrived. Will work on those while I wait for other parts. Gotta get some of the suspension stuff straighten out while I have it all apart before I throw the engine back in.
brushforhireThread starterJohnstown, PA · Mar 8, 2016#43Project is still moving along, just very, very slowly. I had to order a number of random parts to get going again. For some reason the junkyard had took the flexplate off, and I didn't realize there was a plate that was supposed to behind and in front of it. On backorder, or course. The RPM exhaust is gonna be another two weeks.
On the bright side, I am taking the time to attack some of the rust on random parts.
CrankyOldManWest Michigan · Mar 8, 2016#44I'm probably 6 weeks out on mine, trying to pick up smaller components along the way. I've already got the wire harness. Engine ECM, MAF and intake are next on the list.
3cyltrboOttawa · Mar 9, 2016#45 Originally Posted by
CrankyOldMan ↑ I'm probably 6 weeks out on mine, trying to pick up smaller components along the way. I've already got the wire harness. Engine ECM, MAF and intake are next on the list.
I'll be watching that (because I believe you would be the first manual transmission swap to be properly documented?)
Will
brushforhireThread starterJohnstown, PA · Mar 9, 2016#46Quick pic of my front swaybar repaint. It was rusted really badly, so I just took it out and took the angle grinder to it and then primed and repainted. Gonna shoot a couple coats of clear coat, and should be good to go.
Picture not included in this copy1 attachment not included in this copy
CrankyOldManWest Michigan · Mar 9, 2016#47 Originally Posted by
3cyltrbo ↑ I'll be watching that (because I believe you would be the first manual transmission swap to be properly documented?)
That's the plan! =) I don't know if I'll start a thread before I have all the gubbins, because that can be a disaster if I don't get everything and have to abandon the project.
brushforhireThread starterJohnstown, PA · Mar 14, 2016#48A couple quick pics. I have a lot more I am gonna organize to try and provide a more complete guide.
Picture not included in this copy Picture not included in this copy Picture not included in this copy3 attachments not included in this copy
ArmstrongRacingSan Diego · Mar 14, 2016#49Looking good!
brushforhireThread starterJohnstown, PA · Mar 20, 2016#50Here is my rundown of the speed sensor.
The XD harness does not have the speed sensor from the Yaris tranny. The harness plug in the fuse box has the empty spots for it.
The speed sensor on the transmission
Picture not included in this copy The sensor plug:
Picture not included in this copy Picture not included in this copy Use a pin to remove the wires, gotta kinda fiddle with it.
Picture not included in this copy The Three wires you want to remove from the yaris plug:
Picture not included in this copy Picture not included in this copy Where they go in the XD harness plug:
Picture not included in this copy Picture not included in this copy While you at the plug on the XD harness, remove the MAF power wire. It is the black with silver markings.
Picture not included in this copy9 attachments not included in this copy