Replies continued
brushforhireThread starterJohnstown, PA · Mar 20, 2016#51You will need to ground the torque solenoid wire to the transmission.
EDIT: UPDATED PROCESS FOR XD HARNESS. ALL YOU NEED TO DO IS ADD A PIN/WIRE TO THE EMPTY PIN LOCATION 9, NEXT TO THE BLUE WIRE IN SPOT 10, SO YOU CAN GROUND IT OUT. REALLY EASY.
EDIT: NO NEED TO DO THIS PART!! Pull the loom and tape back from the transmission harness.
Picture not included in this copy EDIT: LEAVE THIS WIRE ATTACHED!!! This is the blue wire you want from the upper plug:
THIS BLUE WIRE IS PIN 10. YOU NEED TO ADD A WIRE/PIN FROM YOUR OLD YARIS HARNESS TO PIN LOCATION 9, WHICH IS EMPTY ON THE XD HARNESS. THAT IS WHAT YOU WILL THEN GROUND TO THE TRANSMISSION.
Picture not included in this copy THIS IS WHAT PIN LOCATION 9 SHOULD LOOK LIKE, NOT 10. IN THE SPOT THAT THE BLACK RUBBER PLUG IS IN, NEXT TO THE BLUE WIRE. I grounded it to this point on the case. The hole was not threaded on my trans, so I used a 6MM x 1.00 tap and ran a bolt in there to ground it.
Picture not included in this copy3 attachments not included in this copy
brushforhireThread starterJohnstown, PA · Mar 20, 2016#52I am posting this, because my junkyard thought it was easier to remove the flexplate and spacers and throw them away, instead of leaving them on. I bought a flexplate on put it on, without realizing that there were supposed to be spacers. Ugh.
The supplies:
Picture not included in this copy Picture not included in this copy Inner spacer:
Picture not included in this copy Plate and outer spacer:
Picture not included in this copy The bolts that hold the plate on, put a drop or two of blue threadlock on each bolt. They get torqued down to 65 ft lb.
6 attachments not included in this copy
ArmstrongRacingSan Diego · Mar 20, 2016#53Good work man!
(for those that use a corolla harness don't forget to swap the SL solenoid pin at the ecm also!)
tmontagueCaledonia Ont. · Mar 20, 2016#54Thanks a ton for taking pictures and explaining what wires need to b taken care of. Makes it much easier for future swaps.
Keep it up!
brushforhireThread starterJohnstown, PA · Mar 20, 2016#55 Originally Posted by
ArmstrongRacing ↑ Good work man, don't forget to swap the SL solenoid pin at the ecm also!
I though that was only if you used the Corolla harness. I am using the XD harness.
ArmstrongRacingSan Diego · Mar 20, 2016#56Ohhhhh I missed that, my bad. Carry on sir!
brushforhireThread starterJohnstown, PA · Mar 21, 2016#57 Originally Posted by
ArmstrongRacing ↑ Ohhhhh I missed that, my bad. Carry on sir!
Whew, had me a little nervous there at first, LoL.
3cyltrboOttawa · Mar 22, 2016#58Thank you for taking the time to document all this.
Just like a few others have done, its a huge service and benefit to the Yaris community.
Thank you
Will
p.s..... for anyone else out there considering a Manual 2zrfe swap, I'm waiting for your DIY
brushforhireThread starterJohnstown, PA · Mar 22, 2016#59I am hoping after this is done, to start a new clean thread with everything in some kind of order, so it can be stickied. I got my axles, control arms, knuckles, calipers, rotors, pads all on. Exhaust is in the transit! ETA is Monday. Hoping to do a how to install on that. I know with being a long tube design, that was one of my biggest things, trying to find if I needed to wait to put my engine in, or if it will fit after the fact. It should fit right in with my engine already back in.
I can't thank Armstrongracing enough for being supportive and really figuring out the hard parts of this swap!
ArmstrongRacingSan Diego · Mar 22, 2016#60 Originally Posted by
3cyltrbo ↑ ..... for anyone else out there considering a Manual 2zrfe swap, I'm waiting for your DIY
I will be converting to a manual transmission next year some time so Ill post up a diy on that too for you guys.
ArmstrongRacingSan Diego · Mar 22, 2016#61 Originally Posted by
brushforhire ↑ .... Exhaust is in the transit! ETA is Monday. Hoping to do a how to install on that. I know with being a long tube design, that was one of my biggest things, trying to find if I needed to wait to put my engine in, or if it will fit after the fact. It should fit right in with my engine already back in.
I can't thank Armstrongracing enough for being supportive and really figuring out the hard parts of this swap!
No problem man, we all teach each other something! Im also waiting on the header, so hopefully you are able to squeeze it in there!
xnamerxxso cal · Mar 23, 2016#62 Originally Posted by
brushforhire ↑ I am hoping after this is done, to start a new clean thread with everything in some kind of order, so it can be stickied. I got my axles, control arms, knuckles, calipers, rotors, pads all on. Exhaust is in the transit! ETA is Monday. Hoping to do a how to install on that. I know with being a long tube design, that was one of my biggest things, trying to find if I needed to wait to put my engine in, or if it will fit after the fact. It should fit right in with my engine already back in.
I can't thank Armstrongracing enough for being supportive and really figuring out the hard parts of this swap!
If your long tube is anything like the one I built for myself, or Jason. You should be able to get it in the car by pulling the dogbone and shifting the engine enough to slide it down.
brushforhireThread starterJohnstown, PA · Mar 23, 2016#63 Originally Posted by
xnamerxx ↑ If your long tube is anything like the one I built for myself, or Jason. You should be able to get it in the car by pulling the dogbone and shifting the engine enough to slide it down.
From what I read in another forum, RPM stated that it was designed so it will just slide up from the underside. I hope this is the case.
brushforhireThread starterJohnstown, PA · Mar 29, 2016#64So I received my RPM header and midpipe.
I have some mixed feeling about their product.
First the good:
The header is fantastic. Well made, and assembled. Coating seems durable.
Picture not included in this copy Picture not included in this copy Now onto everything else:
The midpipe is well made, but it is actually a two piece system. The pictures on fastscions and everywhere else show it to look like one piece. If you look close enough you can see that there is infact a slip joint.
Picture not included in this copy Picture not included in this copy The packaging was horrible. All the pipes and parts were thrown into a box without any protection. The pipes were banging against each other and rubbing. Sad for $70+ in shipping charges.
They also made a mistake and forgot to weld on the hanger bars on the front portion of the midpipe. After talking with them, they are sending me a small refund, and I will just weld my own on.
The other thing I am trying to find out is how they expect me to connect the rear midpipe flange to the muffler flange. The factory using a pivoting ball gasket and they used a flat flange.
Now for the rough install:
From what I read they said that the header was designed so it would just twist and slip in from the bottom.
I am not sure if the xD has more clearance, but it does not work on the yaris:
Picture not included in this copy Picture not included in this copy I had to cut down this tab:
Picture not included in this copy After much fighting and beating with a hammer I was able to get the tab to bend just enough to squeeze past the crossmember. Really scratched the heck out of the coating.
Picture not included in this copy Picture not included in this copy Picture not included in this copy I definitely recommend cutting that tab off altogether, or dropping the subframe. I did not want to drop mine because I installed whiteline caster bushings and they were a nightmare to get in.
The midpipe lines up beautifully.
No pics of that yet.
However you will need to lengthen the rear o2 sensor wires to make them reach the new o2 bung on the midpipe.
I installed the DC sports muffler from the xD and two hangars line up perfectly. DC sports has you take a floor grommet out on the xD, but on the yaris it is a different size and shape. So I will probably just bolt/weld a hanger to the floor of spare tire well.
The DC muffler is also alot longer, so it sticks out a bit.
Picture not included in this copy Overall I love the header, but would recommend getting a custom midpipe made, or making one yourself.
I will keep you all updated on this install process of this.
11 attachments not included in this copy
tmontagueCaledonia Ont. · Mar 29, 2016#65For a "new" product that mid pipe looks beat to hell.
Thanks for the update. If I ever do this install down the road i'll b skipping the mid pipe and building my own. I like the header but that mid pipe is garbage for the money it costs.
How essential is that tab that you recommend cutting of?
CrankyOldManWest Michigan · Mar 29, 2016#66That's a shame to hear that there's so many issues with the purchase overall.
What's the midpipe diameter? I've got a custom res-back to axle-back bent section of 2.5" that I haven't installed yet. I bought it for the Blitz S/C setup, but I'm worried about losing too much back pressure on the NA motor. It would also save me the cost of the midpipe and shipping.
brushforhireThread starterJohnstown, PA · Mar 29, 2016#67 Originally Posted by
tmontague ↑ For a "new" product that mid pipe looks beat to hell.
Thanks for the update. If I ever do this install down the road i'll b skipping the mid pipe and building my own. I like the header but that mid pipe is garbage for the money it costs.
How essential is that tab that you recommend cutting of?
Honestly, not real sure what the tab is for. My engine doesn't have any corresponding mounting brackets. Not to say they shouldn't be there.
ArmstrongRacingSan Diego · Mar 29, 2016#68Sad....Im glad I didn't order the midpipe. The tab on the header should be for the support bracket for the header
beakerconyers ga · Mar 30, 2016#69In all fairness to the header manufacturer on the fitment, we are trying to use a header/mid-pipe on a different car than what it was intended for. Doesn't look like any major fabrication to make it work. My only concern would be the flange for the muffler to mid-pipe. The slip joint on the mid-pipe is actually a good thing for this experiment, gives you a little more flexibility in fitment.
brushforhireThread starterJohnstown, PA · Mar 30, 2016#70 Originally Posted by
beaker ↑ In all fairness to the header manufacturer on the fitment, we are trying to use a header/mid-pipe on a different car than what it was intended for. Doesn't look like any major fabrication to make it work. My only concern would be the flange for the muffler to mid-pipe. The slip joint on the mid-pipe is actually a good thing for this experiment, gives you a little more flexibility in fitment.
They had been advertising all over other forums and the internet that it is for the Yaris TS. So once I put the 2zrfe engine into my car, it is basically the same thing, so it should fit exactly the same.
That being said, I dunno if they actually sold a midpipe and header to any actual Yaris TS owners.
The slip joint isn't really needed honestly, but not really hurting anything either, I just like a sealed exhaust pipe.
In regards to the rear flange they told me most people are just using high temp silicone, which worries me. They are sending me a regular gasket that is supposed to work, so I will keep you all updated on that.
beakerconyers ga · Mar 30, 2016#71 Originally Posted by
brushforhire ↑ They had been advertising all over other forums and the internet that it is for the Yaris TS. So once I put the 2zrfe engine into my car, it is basically the same thing, so it should fit exactly the same.
That being said, I dunno if they actually sold a midpipe and header to any actual Yaris TS owners.
The slip joint isn't really needed honestly, but not really hurting anything either, I just like a sealed exhaust pipe.
In regards to the rear flange they told me most people are just using high temp silicone, which worries me. They are sending me a regular gasket that is supposed to work, so I will keep you all updated on that.
The flat gasket will work, you will just have to grind the flange on the muffler side flat, where originally the "half donut" gasket would fit. The should be a protrusion on the flange that holds the original style gasket in place. Or, I may be wrong in thinking the ball is on the muffler side, if it originally was on the mid pipe side, then just use the gasket. I wouldn't use silicone.
If you don't like the slip joint, just put some tack welds on it once you get everything fitted and clamped, pull it down and weld it up.
As for sliding the header on once the cross member and engine are in place, sounds like for others planning on doing this, it would be better to install the header onto the engine prior to installing the engine in the car.
brushforhireThread starterJohnstown, PA · Mar 30, 2016#72 Originally Posted by
CrankyOldMan ↑ That's a shame to hear that there's so many issues with the purchase overall.
What's the midpipe diameter? I've got a custom res-back to axle-back bent section of 2.5" that I haven't installed yet. I bought it for the Blitz S/C setup, but I'm worried about losing too much back pressure on the NA motor. It would also save me the cost of the midpipe and shipping.
The inner diameter of the midpipe is 2" and the outside is 2.25" as per my digital caliper.
LTHatchNewark NJ · Mar 30, 2016#73Looks awesome! Can't wait to hear how angry she will sound with your header setup, and your review on how it drives.
brushforhireThread starterJohnstown, PA · Mar 30, 2016#74 Originally Posted by
beaker ↑ The flat gasket will work, you will just have to grind the flange on the muffler side flat, where originally the "half donut" gasket would fit. The should be a protrusion on the flange that holds the original style gasket in place. Or, I may be wrong in thinking the ball is on the muffler side, if it originally was on the mid pipe side, then just use the gasket. I wouldn't use silicone.
If you don't like the slip joint, just put some tack welds on it once you get everything fitted and clamped, pull it down and weld it up.
As for sliding the header on once the cross member and engine are in place, sounds like for others planning on doing this, it would be better to install the header onto the engine prior to installing the engine in the car.
Luckily the little part you are talking about was on the midpipe side originally, so the gasket should be the ticket.
I will probably just end up welding the slip joint like you said.
I would install the header before putting the engine in, or drop the crossmember.
Honestly though, I would probably just cut that tab off. I will have to cut it off with an angle grinder if I want to get the header back out. I can always fab up another mount if I need to. I am not gonna bother with a mount bracket for now.
MugenRepCentral Pennsylvania · Mar 30, 2016#75Great results. Good to see a quick Yaris locally. Are your pans to do SCCA, strip racing, road racing, NASA, etc. with it?
brushforhireThread starterJohnstown, PA · Mar 30, 2016#76 Originally Posted by
MugenRep ↑ Great results. Good to see a quick Yaris locally. Are your pans to do SCCA, strip racing, road racing, NASA, etc. with it?
I would love to do autocross, but I have no idea where to go or start with it. I might try to enter orbit with it, but I might need to add a turbo to it, before I start true space exploration.
CrankyOldManWest Michigan · Mar 30, 2016#77lmgtfy =P
The NASA in question is the North American Sportscar Association. Similar to SCCA, but with different rules and classifications.
The best way to get into autocross is to find a local event, register, show up, and enjoy the day.
ArmstrongRacingSan Diego · Mar 30, 2016#78scca.com > find my region ��
MugenRepCentral Pennsylvania · Mar 31, 2016#79 Originally Posted by
brushforhire ↑ I would love to do autocross, but I have no idea where to go or start with it. I might try to enter orbit with it, but I might need to add a turbo to it, before I start true space exploration.
Lol, if space exploration is in question I'd start with the void im finding between some people's ears at my current job.
SCCA Central PA is pretty active. Their Facebook group seems to answer questions pretty quickly and they are one of the least condescending groups I've participated in. Not sure what class you'd be in, but according to the last time I checked I'm stuck in STS and although I'll be non-competitive it'll be great experience in learning to drive my car better. Last I looked it was $35 at most events for non-SCCA members for a Sunday fun run.
brushforhireThread starterJohnstown, PA · Mar 31, 2016#80I finally found this group:
Allegheny Highlands Region SCCA They hold their events like 40 minutes from my house, and their club meetings like only 5 minutes from my house. Woo!
ArmstrongRacingSan Diego · Mar 31, 2016#81Nice! We're going to have a 2zr swap on each coast! 3 so far guys!
MugenRepCentral Pennsylvania · Mar 31, 2016#82 Originally Posted by
brushforhire ↑ I finally found this group:
Allegheny Highlands Region SCCA They hold their events like 40 minutes from my house, and their club meetings like only 5 minutes from my house. Woo!
Very very nice!!!
CrankyOldManWest Michigan · Mar 31, 2016#83 Originally Posted by
ArmstrongRacing ↑ Nice! We're going to have a 2zr swap on each coast! 3 so far guys!
Does MI count as the north coast? =P
(My bonus shows up on Monday. SOOO EXCITED!)
brushforhireThread starterJohnstown, PA · Mar 31, 2016#84 Originally Posted by
CrankyOldMan ↑ Does MI count as the north coast? =P
(My bonus shows up on Monday. SOOO EXCITED!)
Awesome! At the rate I am getting to work on my car, you'll have yours done before mine. LoL.
ArmstrongRacingSan Diego · Mar 31, 2016#85 Originally Posted by
CrankyOldMan ↑ Does MI count as the north coast? =P
(My bonus shows up on Monday. SOOO EXCITED!)
YES! muahahaha!
Auto or Manual?
CrankyOldManWest Michigan · Mar 31, 2016#86 Originally Posted by
brushforhire ↑ Awesome! At the rate I am getting to work on my car, you'll have yours done before mine. LoL.
Nah, I'll be in Mexico for a week, home for a week, then in China for a week. No idea where I'll be in May.
Originally Posted by
ArmstrongRacing ↑ YES! muahahaha!
Auto or Manual?
Manual. I've only got the wire harness so far, but intend to order the exhaust and ECU ASAP, and buy the motor as soon as I get back from MX.
On a side note, can you measure the ID of the MAF section? I grabbed the top of a 1ZZ Matrix/Vibe airbox at the junk yard, but I don't know if it's the right ID for the xD MAF sensor. I plan on using a CAI anyway, but need to know the right diameter to prevent a bunch of CEL issues.
brushforhireThread starterJohnstown, PA · Apr 1, 2016#87As a side note, I was able to reuse my old a/c lines, so I did not have to order any new ones. Thankfully. I know Armstrongracing had to use new ones, so if you have a sedan it might be different.
I got my starter and alternator wires upgraded. Did a bigger ground for the front because my battery is not located behind the passenger seat. I went with 1/0 oversized. It's obscenely huge, lol. I also used the 1/0 wire for the ground from the battery to the body.
I have to figure out where to run my 1/0 power wire from the battery to the engine bay now. I was gonna run it through the grommet where the 4 ga was, but there is not way 1/0 oversized wire is fitting through that grommet on the drivers side! Probably just drill a hole in the firewall and hide the power wire a little better.
CrankyOldManWest Michigan · Apr 1, 2016#88Mine's a 3DR hatch. Did you have to get the xD alternator and A/C compressor?
Originally Posted by
brushforhire ↑ I have to figure out where to run my 1/0 power wire from the battery to the engine bay now. I was gonna run it through the grommet where the 4 ga was, but there is not way 1/0 oversized wire is fitting through that grommet on the drivers side! Probably just drill a hole in the firewall and hide the power wire a little better.
There's another grommet behind the passenger airbag. It's easiest to see it from the engine bay, but it's under the wiper cowl. Probably a 5/8" diameter hole.
brushforhireThread starterJohnstown, PA · Apr 1, 2016#89 Originally Posted by
CrankyOldMan ↑ Mine's a 3DR hatch. Did you have to get the xD alternator and A/C compressor?
There's another grommet behind the passenger airbag. It's easiest to see it from the engine bay, but it's under the wiper cowl. Probably a 5/8" diameter hole.
I did get the alt and compressor. The xD pulleys have more ribs.
I will check for that grommet, thanks!
CrankyOldManWest Michigan · Apr 1, 2016#90 Originally Posted by
brushforhire ↑ I did get the alt and compressor. The xD pulleys have more ribs.
I totally knew that. 🙄
invader166Langley, BC · Apr 1, 2016#91 Originally Posted by
CrankyOldMan ↑ On a side note, can you measure the ID of the MAF section? I grabbed the top of a 1ZZ Matrix/Vibe airbox at the junk yard, but I don't know if it's the right ID for the xD MAF sensor. I plan on using a CAI anyway, but need to know the right diameter to prevent a bunch of CEL issues.
Cranky, you should try to fit the 2ZR into the MR2. 😉
This way you get a (simmilar) 3rd gen. powertrain in a 1st gen. shell.👍
CrankyOldManWest Michigan · Apr 1, 2016#92 Originally Posted by
invader166 ↑ Cranky, you should try to fit the 2ZR into the MR2. 😉
This way you get a (simmilar) 3rd gen. powertrain in a 1st gen. shell.👍
The Yaris is getting the 2ZR because it needs a stock OEM motor. The MR2 is getting the boosted 1NZ so that the finicky supercharger is with the playtoy/racecar. I drive about 40 miles one way to work, and have trashed 2 crank pulleys in the past 12 months.😢
brushforhireThread starterJohnstown, PA · Apr 1, 2016#93A couple quick shots of the a/c lines.
Picture not included in this copy Picture not included in this copy2 attachments not included in this copy
brushforhireThread starterJohnstown, PA · Apr 6, 2016#94I'm still moving along on this. Just very slowly. I only get about an hour and a half a day to work on this. I'm also painting the car as I go, so that is really slowing me down.
As a side note, I decided to use the mount that came with he dc sports xD muffler. It it is a square top and at a first I didn't think it would work, because the hole is round, but I realized that it is probably the same on the xD. It fits in very snug, and it seems like it will work. It is secure in place, and almost seals up. It looks like it has ridges that sit firmly against the bottom of the body. I will probably just squeeze some silicone into the small opening on either side and call it good.
Things that still need done:
Finish putting engine bay back together
Finish wiring and installing gauges
Connect up ground and power wires to the battery in the rear of the car - waiting on a fuse holder for 1/0 wire
Finish painting as much of the car as I can
Bleed the brakes - pray no leaks
Fill the trans with fluid
Fill the coolant system
Finish installing the intake - waiting on a coupler
Weld on two hangers for the exhaust
A couple other small odds and ends
Goal is to have it started and running next weekend.
GolddeenohColumbia, SC · Apr 8, 2016#95I'm so following this
yes i still get on nearly everyday, i just don't always comment or read through everything.
brushforhireThread starterJohnstown, PA · Apr 12, 2016#96Oh man, I am so close to starting this little monster. I welded the exhaust last night, still no extra hangers yet, though. I will get to them later. I put a new oil filter and oil in the engine.
As a side note, remembering to turn on the shielding gas really helps, lol.
So far it looks like a start and run will happen this weekend! Then I just gotta finish the painting and then I can start driving it again.
ArmstrongRacingSan Diego · Apr 12, 2016#97awesome!
fnkngrvIn The Hotbox · Apr 13, 2016#98W00t W00t
Sent from m-o-b-i-l-e
brushforhireThread starterJohnstown, PA · Apr 15, 2016#99It lives! I officially started it about 20 minutes ago! It sounds fantastic. So much better than I could have hoped for. Tomorrow I hope to test drive it, and take a quick video of the sound of this little beast. Should it road worthy for next week, I hope.
I do have a check engine light, but I am hoping it is something simple like the MAF sensor. I just used the used one that came with the little piece for my intake, and I am thinking it may be bad. I will change to the new a/m one I bought and see if that helps. Brakes are all bled and seem to be working in good order. I did so many things at once to this, I wanna take me time and make sure nothing falls off, when I finally take it out on the road.
Edit: Video delayed, still trying to get a few odds and ends together before driving. Ugh.
fnkngrvIn The Hotbox · Apr 15, 2016#100Good to hear. I just got my sedan back after cleaning the fuel system and installing the new resonator. I am super excited that I can now drive it.
Sent from m-o-b-i-l-e