Replies continued
Focus_Sh1ftNew Jersey · Dec 10, 2015#101 Originally Posted by
fnkngrv ↑ It will be a learning curve no matter what with the conversion to cable TB since it will be instant throttle response. I know that when Garm took me for a ride he was having difficulty hooking up to a point with his LB. AFAIK his LB actually had a Motec EMS and not AEM so that may have been a contributing factor. There are still a ton of features I have not tapped into with my EMS.
Sent from my XT1575 using Tapatalk
Actually, his tC has the Motec, and I kind of hate it. It's comprehensive, but it's dated and I absolutely hate that Motec hides additional features behind a paywall ($180 for traction control, $800 FOR CLOSED LAMBDA TUNING - I MEAN C'MON REALLY?)
His LB had an AEM EMS, but that doesn't necessarily mean traction control was tuned since it's more work. The good news is that even if you throw on really wide tires, you probably won't be in tram-lining territory.
fnkngrvThread starterIn The Hotbox · Dec 12, 2015#102Traction control in a stand alone can only go so far anyway since it isn't tied into the actual suspension on this chassis. Only time will tell on how this goes. The few other sedans I have seen running serious power essentially have to have a very specific tune to maximize take off and gear change performance.
Sent from my XT1575 using Tapatalk
fnkngrvThread starterIn The Hotbox · Dec 13, 2015#103Battery relocation and exhaust have been completed. Did a first start up this afternoon:
Tiamat 2015 First Start Hard to believe that the car has been off the road for over a year! This is a quick video of the new setup at first start. Seem to have a fuel pressure sensor issue or something as the gauge isn't reading correctly compared to what the EMS is showing so will need to figure that one out. Next step will be getting her loaded up and brought to the dyno hopefully in the next couple weeks.
Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy LTHatchNewark NJ · Dec 13, 2015#104Holy space balls, that doesn't sound like any econobox i have ever heard lol. Sounds amazing, you did an outstanding job on your Yaris.
Is the exhaust hitting the rear tow hook?
fnkngrvThread starterIn The Hotbox · Dec 13, 2015#105No, but it is pretty close. That is the problem with this body kit to be honest. We do have one hanger left to place on the passenger side and then the dummy pipe on the driver's.
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 13, 2015#106Ahhh ok, in the picture that shows your rear springs, what the heck is in your right rear spring?
fnkngrvThread starterIn The Hotbox · Dec 13, 2015#107I have spacers in the springs because the body kit actually drops the base of the body by ,1 1/2" compared to the stock S lip kit. Eventually I will get my tanabe coilovers in, but it will have to wait as I am getting pretty tapped out now from the build.
Sent from my XT1575 using Tapatalk
tmontagueCaledonia Ont. · Dec 13, 2015#108What an awesome sounds. When your Yaris was cranking and something hit the floor I thought it was your engine...my heart skipped a beat for a minute until I realized that your engine was still turning over fine
fnkngrvThread starterIn The Hotbox · Dec 13, 2015#109Yeah, that was actually the engine backfiring. With how much has changed the cold and hot tunes need to be adjusted a fair amount. We also need to figure out the fuel issue.
Sent from my XT1575 using Tapatalk
Focus_Sh1ftNew Jersey · Dec 14, 2015#110
Sounds amazing!
BTW, what tails are those, altezza?
fnkngrvThread starterIn The Hotbox · Dec 14, 2015#111fnkngrvThread starterIn The Hotbox · Dec 20, 2015#112As previously stated the hydrodipped CF valve cover was damaged due to rubbing issues so I decided to have the cover PC'ed to match the new IC piping. Also upgraded the valve cover bolts to an ARP set which looks much better and will stand up to conditions for a long time to come. Unless mistaken I am now 100% completed under the hood.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 20, 2015#113That color is beautiful and almost distracting enough to hide that big snail attached to your Yaris lol
fnkngrvThread starterIn The Hotbox · Dec 22, 2015#114Yeah I really love the purple for sure. We installed a shorty bullet stainless racing muffler yesterday. Really lowered the tone of the exhaust to a nicer less ricey note however didn't do much for reducing the db. I am thinking the only way to tame that is with another chambered muffler, but don't want to reduce performance.
Sent from my XT1575 using Tapatalk
fnkngrvThread starterIn The Hotbox · Dec 26, 2015#115Brought her home from the shop today and she is definitely running super rich. All that extra air makes a big difference. Working right now to figure out the schedule to take the car down to the Dyno and hoping to do it within the next 30 days. Can't really come to soon.
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 26, 2015#116That's great news, one last step in the way for you to set new land speed records. Should we start guessing how much she'll put down?
fnkngrvThread starterIn The Hotbox · Dec 26, 2015#117If you would like you can. I had hopes for certain numbers last year however learned to not count chickens before they are hatched. We are fighting with over boost situations right now and still the fuel pressure gauge not watching to cooperate. These will need to be resolved first. I have a 12psi spring in the wastegate so by what AEM says their boost controller does the max boost should not go over 24psi. The big problem is that my current boost gauge only goes to 20psi so I will need to invest in a new one.
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 26, 2015#118Over boost? Do you know what's causing that on your setup?
fnkngrvThread starterIn The Hotbox · Dec 26, 2015#119We aren't sure just yet. I had been set at 15 across the entire rpm range previously, but we have buried the needle at 20 the few times we have tested wot. It isn't over boosting per the controller ability AFAIK by the data logger, but still needs to be figured out since the fuel quality here isn't good enough to be hitting 20+ for me and feel comfortable.
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 26, 2015#120Ah ok, so i assume there is no E85 locally where you live or you want to stay with 91/93? So a 5 psi overboost and she held together? That is a dang good tune.
fnkngrvThread starterIn The Hotbox · Dec 26, 2015#121No e85 for at least 400 miles. Plan is street tune with 91 while still in Maine, then 93/95 in TX. Race tune will be with c12. My fuel pump isn't the model for use with e85, but everything else will support it.
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Dec 26, 2015#122Sounds like a good plan, congrats on moving to a state with far friendlier car atmosphere. Curious how much the higher temperatures in Texas will affect your land speed runs.
fnkngrvThread starterIn The Hotbox · Dec 26, 2015#123All goes well I will be able to tell you in October. Plans are to race in the Texas Mile at the least and possibly the Arkansas Mile as well.
Sent from my XT1575 using Tapatalk
Chief QuimbyDenmark · Dec 27, 2015#124What compression ratio do you have.
I ran 33,5 psi on pumpgas oktan 93.
Is the overboosting in 4-5 gear, mabey wg is to small.
Do you have boostcreep in lower gears ?
fnkngrvThread starterIn The Hotbox · Dec 27, 2015#125CP 9:1 pistons. We will figure out the boost issues once we get down to the Dyno. What were you running 33psi of boost on?
Sent from my XT1575 using Tapatalk
Chief QuimbyDenmark · Dec 28, 2015#126Well, 33psi is maney abit to much at 9-1 :-)
Ran it on my starlet 5e engine, but the compression was low around 8-1
fnkngrvThread starterIn The Hotbox · Jan 2, 2016#127Today was a nice day so I was going to take her for a much needed bath to get the shop grime off, but alas the battery not being used much didn't want to give me a start so put her on the charger for the night and will do it tomorrow. While out in the garage tho I did snap a few more shots under the hood.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Jan 3, 2016#128That's a very thick radiator, who makes that for the Yaris? The radiator mounts on the sedan are the same as the hatch?
fnkngrvThread starterIn The Hotbox · Jan 3, 2016#129 Originally Posted by
LTHatch ↑ That's a very thick radiator, who makes that for the Yaris? The radiator mounts on the sedan are the same as the hatch?
It is the 90-92 Honda Civic EX 3 core. Fellows from the UK clued me in on it. Bottom lines up fine. You just have to fab an L bracket top loop mount for it and then use a straight section of hose for the top return line to the rad. So far it has dropped my engine temps by roughly 25° under normal load alone.
Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Here is a link to pretty much what I now have:
http://ebay.com/itm/3-ROW-CORE-ALUMI...-/350589900140 Sent from my XT1575 using Tapatalk
LTHatchNewark NJ · Jan 3, 2016#130That's awesome, thank you.
fnkngrvThread starterIn The Hotbox · Jan 3, 2016#131 Originally Posted by
LTHatch ↑ That's awesome, thank you.
Not a problem. AFAIK it will fit both the sedan and LB the same if not very similar since it is a half rad.
Sent from my XT1575 using Tapatalk
fnkngrvThread starterIn The Hotbox · Jan 7, 2016#132Have to take the car 60 miles to the local stealership for the 3 outstanding recalls (seat rails, spiral cable, and window controls) tomorrow so worked on the Cold start a little more.
Today was in the high 30s, but still she starts hard. Working with all the air flow that has been increased in cold weather makes for an interesting start.
Cold Start 20160107 Focus_Sh1ftNew Jersey · Jan 8, 2016#133Oh man, that cold start definitely needs some work. 😆
I'd definitely recommend throwing a resonator on to further reduce the noise. It will really help to knock that "raspy" tone down quite a bit.
Bluevitz-rsOshawa, Ontario, Canada · Jan 8, 2016#134What's the AFR?
fnkngrvThread starterIn The Hotbox · Jan 8, 2016#135 Originally Posted by
Bluevitz-rs ↑ What's the AFR?
Pig rich tbh. Sitting in the 10s and 11s. The colder ambient temps aren't helping any that is for sure. Doing some work on it over the weekend.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jan 8, 2016#136Sounds a bit off but mean as all hell, when you go to the dealership tell us the expression on the techs faces after they see/hear you pull in lol.
47_MasoN_47Northwest Alabama · Jan 8, 2016#137I'd love to see the expression on their faces as well. I've still gotta get mine in for all those recalls too :/
malibuguyWestminster, MD · Jan 9, 2016#138I just love this car
FreestylinCalgary, Alberta · Jan 9, 2016#139fnkngrv, mad props for this crazy setup! I absolutely love the way it sounds as it sits right now! Keep it up!
fnkngrvThread starterIn The Hotbox · Jan 9, 2016#140Did some tune tweaking and made another cold start test today that was much more successful. It was 22° out also so that was a good sign. Also got a confirmation that the likelihood of the Dyno being available this month is very slim which is a serious bummer.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jan 10, 2016#141My apologies if its been asked already, are you tuning vvti also? Do you believe theres a noticeable power increase tuning vvti for your turbo setup?
fnkngrvThread starterIn The Hotbox · Jan 10, 2016#142No worries. Yes we are also tuning vvti. As for differences there is a long story to being able to notice if there are differences or not concerning the Dyno work last year.
The short version is that due to an initial incorrect wiring install of the AEM boost controller and then plugged cat my tune and work done to it was seriously hampered. We wasted so much time working on those two items that granular manipulation for many settings were reduced by a great deal.
Even though last year's build/tune were an improvement and edged up performance/speed it just was a horrible cost/benefit situation. When it was said and done just the shop work/time at Granite State Dyno ran me close to $1500. That doesn't include the cost of the trip and GSD sits 400 miles from home. I had budgeted for half of that. With those expenses ballooning the way that they did further work was obviously hurt. We did do further analysis/tweaking during the speed runs with logger data, but just plain ran out of time for any performance improvement over the spring based tune. I only ran c12 race gas for safety as we didn't even get to really tune for it over 93 unleaded.
This time around I am working to have JRT Customs perform the tune at a much closer shop (200 miles) on the coast of Maine. The travel costs will be almost the same because we will be trailering the car and we will be around 10mpg with the truck/trailer. The Dyno cost and tuning cost will be where the big savings will be. I will have the Dyno for an entire day for a fraction of the cost.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jan 10, 2016#143On another note this new replacement AEM fuel pump seems to be getting louder very similar to the original one. I will be reaching out to them this week to discuss what is going on. An aftermarket fuel pump will be louder than stock, but even with how loud my injectors are you can hear the pump over them. Depending on what happens I may ditch the AEM and move to an Aeromotive unit instead. I have considered a Deatschwerks unit as well, but those are definitely loud from my research.
Before anyone asks after talking at length with Walboro engineers I prefer to not use one of their units for what my design is.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jan 10, 2016#144Is your AEM pump causing fuel pressure issues?
fnkngrvThread starterIn The Hotbox · Jan 10, 2016#145Not sure yet, but don't believe so. The behavior of this pump however is very similar to the last one. Started off fine however as time went on it became louder and louder. AEM determined the first pump was actually missing internal fittings that frankly could have caused a catastrophic event. I was very lucky. The only reason why I used another one was because AEM covered all costs.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jan 10, 2016#146Ah i see, do you have any safety nets in place if there is a fuel pump issue during a land speed run?
1nz revolutiontx · Jan 10, 2016#147WELDON FUEL PUMP. Best race pumps on the market. AEM doesn't even make theirs. All those designs are all based off Walboro.
fnkngrvThread starterIn The Hotbox · Jan 10, 2016#148 Originally Posted by
LTHatch ↑ Ah i see, do you have any safety nets in place if there is a fuel pump issue during a land speed run?
Not really when it comes to that.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jan 10, 2016#149 Originally Posted by
1nz revolution ↑ WELDON FUEL PUMP. Best race pumps on the market. AEM doesn't even make theirs. All those designs are all based off Walboro.
Your new threads and posts smell a like like you are Aras. Am I correct?
Sent from m-o-b-i-l-e
1nz revolutiontx · Jan 10, 2016#150Surge tank set up. No chance of starvation.
1 attachment not included in this copy