Yarisworld Archive

FS: tooter I.V 2 inch thick intake manifold spacer

116 posts · 46,242 views · page 3 of 3

Replies continued

CrankyOldManWest Michigan · May 25, 2014#101
Damn you Helmholtz!! =)
j-sanMN · May 25, 2014#102
This spacer looks pretty neat. How easy is it to install? Looks like you just remove the decorative engine cover, remove the original manifold screws, pull the manifold out a little, slip the spacer in and bolt it back down with the longer screws? Sounds like some hoses may need replacing with longer ones?
tooterThread starterLos Angeles · May 25, 2014#103
Originally Posted by j-san ↑
This spacer looks pretty neat. How easy is it to install? Looks like you just remove the decorative engine cover, remove the original manifold screws, pull the manifold out a little, slip the spacer in and bolt it back down with the longer screws? Sounds like some hoses may need replacing with longer ones?
Yes. Some of the hoses do need to be longer because the whole intake manifold with the throttle body is moved towards the front of the car 2 inches. But as far as the spacer itself, it simply bolts on using the longer threaded studs and nuts that come with it.

The stock rubber intake hose will deflect enough to fit the new location of the throttle body. If you have an aftermarket intake, you'll need to find a way shift it around to fit.

The spacer uses exactly the same O ring gasket as the stock intake manifold to make a reliable no-leak seal...

Picture not included in this copy

It's not a high performance part because it doesn't do anything for your top end. But the longer intake runners do allow the engine to pull stronger at low rpms which is nice in normal everyday driving.


Greg
j-sanMN · May 25, 2014#104
That's what my Yaris is - a daily driver. Some reports suggest a slight MPG increase which would be much appreciated. Mods that can increase mileage and power are rather interesting to me. I don't plan to do major mods to upset the great mileage I've been getting.

I plan on keeping the stock airbox so it's good to know the two are compatible. Does it come with a gasket or do I reuse the original one?
tooterThread starterLos Angeles · May 26, 2014#105
Originally Posted by j-san ↑
That's what my Yaris is - a daily driver. Some reports suggest a slight MPG increase which would be much appreciated. Mods that can increase mileage and power are rather interesting to me. I don't plan to do major mods to upset the great mileage I've been getting.

I plan on keeping the stock airbox so it's good to know the two are compatible. Does it come with a gasket or do I reuse the original one?
Same here... 🙂 Ours is my wife's daily driver so all of the engine internals and ECU stay stock with no tuning, so it's rock solid reliable and runs on cheap 87 octane gas.

The stock air boot is a stretch, but it will work as it is.

The original O ring gasket stays right where it is on your stock manifold so that it can seal when it's bolted onto the spacer. It'll be like this...

Picture not included in this copy

One gasket between the manifold and the spacer and one gasket between the spacer and the head.

As far as gas mileage, our 2012 5 speed hatchback is EPA rated at:

30 mpg City
33 mpg Combined
38 mpg Highway

The average gas mileage for the last three fillups with the tooter I.V spacer is 37.3 mpg...

...and this is even with no freeway driving and my wife over revs the engine. 🙄


Greg
tooterThread starterLos Angeles · Jun 11, 2014#106
I'm down to the last one now...

Picture not included in this copy

$265 includes domestic US shipping

PayPal: greggabi@verizon.net


Greg Mamishian
21444 Entrada Road
Topanga, CA 90290
310-455-3340
greggabi@verizon.net
tooterThread starterLos Angeles · Jun 21, 2014#107
bump
tooterThread starterLos Angeles · Aug 17, 2014#108
That last one sold a while ago so I had six more made. They're in stock and ready to ship. 🙂

Greg
TommyYarisCalgary, AB · Oct 17, 2014#109
Hey Tooter,

The spacer looks like a well crafted component. Is there any extra cost to ship north of the border? Calgary, AB Canada to be exact. I'm not current on exchange rates either so do you know what $295 USD is in CAD?
japleKuala Lumpur, Malaysia · Oct 20, 2014#110
how much does it cost to ship it to malaysia?
thebarberGrand Rapids, MI · Jan 28, 2016#111
makes me wish i still had a yaris
ezhacker1San Francisco · Jan 30, 2016#112
ill be holding onto my forever and forever. such a rare part made from an awesome man.
MedMantleSouth Africa · Jan 30, 2016#113
I joined the scene too late so I never even knew :(
invader166Langley, BC · Jan 31, 2016#114
Wow! $265 is a great deal! If i was to try and fabricate one, it would cost me at least $300+, not including mounting hardware and gaskets.
MugenRepCentral Pennsylvania · Mar 8, 2016#115
Are there future plans for more production?
CrankyOldManWest Michigan · Mar 8, 2016#116
Originally Posted by MugenRep ↑
Are there future plans for more production?
No, Tooter has done all of his projects as limited production runs with no intention of long-term availability. They were all "science projects" that he put into small production runs to spread the cost of the development and manufacturing over a dozen or so parts.

If you have local manufacturing capabilities, you may be able to use the 1ZZ to 1NZ flange I posted in another thread. (Also a Tooter project, that I helped develop)