thatbryanguyOriginal postSC · Apr 10, 2013#1I'm cross posting this here for the hope of reaching someone who knows for sure!!
Ok so here's the story...I got an AEM FIc and a boomslang harness last year. Installed and tuned naturally aspirated making about an extra 10hp/7ish torque in so low spots. On the last dyno pull my engine bogs out and dies with what has become a dreaded crank sensor malfunction code. Sent the FIC to AEM and other sources to determine it was the FICs fault. Internals were replaced and sent back to me with the same problem, sent off again spending another $100 for shipping the harness and FIC all over the US to make sure it's the FIC and it was (AEM denied it being the FIC this time) sent back to me and after AEM this time said they did nothing but tests to see if the FIC was putting out the right signals, it seems it works now. I have recently bought a zage turbo kit so I definitely want this to work now! Installed the harness and FiC and no more crank signal CEL!! Yay!...
BUT a new CEL has arrived. "MAF or VAF circuit A too high input" says my actron pocket scan thingy. If I erase this code, the engine immediately stalls out.
P0103 is the code. Hooking up my air hoses wrong? Or could this link to the FIC beig bad again? I'm clueless...
Replies 134
CTScottUSA, CT · Apr 10, 2013#2Did you load a base map into it when you got it back (and change the injector response time from the default to at least 800us)?
Where did you hook up the FIC's hose to?
thatbryanguyThread starterSC · Apr 10, 2013#3I didn't load a base map on it, I have no idea what that would do but if that would cause this then that's probably the answer. I'm almost positive the hoses aren't the problem...just didnt want to 100% rule the options out.running from that maf sensor Tee'd between that hose going to the intake manifold.
thatbryanguyThread starterSC · Apr 10, 2013#4Any chance loading a cal file on there would bring back that old CEL we were seeing Scott? They tested my cal file at AEM and said there wasn't a problem with that cal file.
CTScottUSA, CT · Apr 10, 2013#5 Originally Posted by
thatbryanguy ↑ Any chance loading a cal file on there would bring back that old CEL we were seeing Scott? They tested my cal file at AEM and said there wasn't a problem with that cal file.
Good question. I can't remember if I tried your cal file or just loaded mine on it before connecting yours on my car. Can you email me your cal file?
thatbryanguyThread starterSC · Apr 11, 2013#6Yea I'll email it to you. I do remember sending it to you but I'm not sure I remember if you said you used it. I think I sent it to you to make sure everything was set right because I have no idea what I'm looking at hah.
CTScottUSA, CT · Apr 11, 2013#7 Originally Posted by
thatbryanguy ↑ Yea I'll email it to you. I do remember sending it to you but I'm not sure I remember if you said you used it. I think I sent it to you to make sure everything was set right because I have no idea what I'm looking at hah.
You can actually start with the blank map that AEM includes and then just change the injector response time on the settings section to 810us. With that, on a stock car everything should run fine with not codes being thrown.
thatbryanguyThread starterSC · Apr 11, 2013#8I'll give that a shot in the A.M. I sure hope it's all good now. It's been a long journey and way too much money for just an FIC because of all the shipping back and forth all over the place haha.
47_MasoN_47Northwest Alabama · Apr 15, 2013#9After the adventures that fnkgrv had with his FIC and some others like this I'm just not so certain about those things...
Scubaru Stevecalgary · Apr 15, 2013#10do you still have the jump leads that you can disconnect the fic with all wiring installed?
try that see if anything happens. if still a problem, its wiring or car sensor
save your map and create a new map with all values 0, see if you still have issues.
if so its the fic unit again. do you have a scan gauge with freeze frame? that will tell you exactly when the code popped. you can also cross reference and watch values change.
hope this helps a bit.
thatbryanguyThread starterSC · Apr 20, 2013#11Alright so CTScott suggested the problem may be with the '07 yaris ECU. Apparently there was a common issue with this ECU having an overly sensitive crank sensor input or something along those lines. So before buying an '08 ECU to hopefully fix this long running fight against getting the FIC to work in my Yaris, I installed everything in an '09 yaris. Fingers crossed that car ran fine with no codes thrown or anything! So if anyone else out there is trying to get the AEM FIC to work in an '07 yaris but having trouble, this may be a part of the solution. Getting ready to order an '08 ECU and will update if everything works out!
mazillaSan Jacinto California · Apr 20, 2013#12D'Oh! I just bought a boomslang/fic...this thread fills me with confidence.
thatbryanguyThread starterSC · Apr 20, 2013#13Yea if you get this problem then there may be hope! It's another $50 hope, but it's hope none the less! I'll update as soon as my new ECU comes in (cost $60 after shipping) to confirm this as a solution!
Today I just installed the AEM fic in a 2008 yaris I set the response time to 810us and calibrated it, I am using the 1.07hex file that it came installed with I have no issues at any RPM (hope it stays that way). I am running NA at the moment preinstalled to get some factory data before I go boosted.
thatbryanguyThread starterSC · Apr 21, 2013#15Sweet that's good news to hear, yea my '08 ECU should be in sometime this week and hopefully this nightmare will be over and I can get on with installing my turbo!
AEM fic still working well today.
cali yarisCanoga Park, CA · Apr 22, 2013#17great news
thatbryanguyThread starterSC · Apr 27, 2013#18Update, got my 08 ECU in and the car runs good with that and I don't get the crankshaft position sensor CEL anymore when i plug the FIC in. BUT now my car dies out with 3 misfire codes. Random misfire, cyl 1, and cyl 3. What could this be caused by?
CTScottUSA, CT · Apr 27, 2013#19 Originally Posted by
thatbryanguy ↑ Update, got my 08 ECU in and the car runs good with that and I don't get the crankshaft position sensor CEL anymore when i plug the FIC in. BUT now my car dies out with 3 misfire codes. Random misfire, cyl 1, and cyl 3. What could this be caused by?
Excellent on the crank issue. On the dying with a misfire one, is your injector response time up at 810us or more?
thatbryanguyThread starterSC · Apr 27, 2013#20Yea it should still have that same cal file I sent to you loaded on the FIC. I'll plug it in tomorrow and check everything again.
thatbryanguyThread starterSC · Apr 28, 2013#21It's set to 810us for injector response. Wonder what else could cause something like this.
CTScottUSA, CT · Apr 28, 2013#22 Originally Posted by
thatbryanguy ↑ It's set to 810us for injector response. Wonder what else could cause something like this.
If you stick the FIC bypass connector on does it run correctly?
thatbryanguyThread starterSC · Apr 29, 2013#23I'm actually having trouble finding my bypass harness since my last install/removal. So I haven't tried that out yet.
thatbryanguyThread starterSC · May 27, 2013#24ok after a little break from the modding game and enjoying my new wheels, i finally got around to finding my bypass connector and it runs fine with it connected. Its only when the FIC is connected that the misfires occur. These misfires also occur in my fiance's sisters yaris.
CTScottUSA, CT · May 27, 2013#25 Originally Posted by
thatbryanguy ↑ ok after a little break from the modding game and enjoying my new wheels, i finally got around to finding my bypass connector and it runs fine with it connected. Its only when the FIC is connected that the misfires occur. These misfires also occur in my fiance's sisters yaris.
You don't by any chance have someone else nearby with a FIC, where you can try that in place of yours?
thatbryanguyThread starterSC · May 27, 2013#26I don't unfortunately...and I currently don't have the funds to pick another FIC up just to test.
CTScottUSA, CT · May 27, 2013#27 Originally Posted by
thatbryanguy ↑ I don't unfortunately...and I currently don't have the funds to pick another FIC up just to test.
Maybe I should ship you mine to test with.
yariSB86OH · May 27, 2013#28Since me and OP are experiencing the same problem with our 07 ECU, I'm going to replace mine as well. I found a slightly used one for $95. Gotta wait for it to get in, then ill update with results.
CTScottUSA, CT · May 27, 2013#29 Originally Posted by
yariSB86 ↑ Since me and OP are experiencing the same problem with our 07 ECU, I'm going to replace mine as well. I found a slightly used one for $95. Gotta wait for it to get in, then ill update with results.
fnkngrv as well. He swapped my FIC in and the problem went away, but we are going to try an 08 ECM on his as well.
thatbryanguyThread starterSC · May 27, 2013#30Man that would be a great help Scott but let me double check everything one last time before I bother you with all of that.
CTScottUSA, CT · May 28, 2013#31 Originally Posted by
yariSB86 ↑ Since me and OP are experiencing the same problem with our 07 ECU, I'm going to replace mine as well. I found a slightly used one for $95. Gotta wait for it to get in, then ill update with results.
If you haven't ordered it yet, I can now do the firmware updating on existing ones to load the new version that corrects the issue.
thatbryanguyThread starterSC · May 28, 2013#32Hmm, how much if I send you my '07 ECU just to have it updated? id like to run my original ECU if I could.
yariSB86OH · May 28, 2013#33Darn, I just placed the order for my 08 ecu yesterday...wasnt too bad though, only $119 shipped. If that doesn't work: with bryans question, how much would you like scott? if we sent our stock 07 ecus to you.
CTScottUSA, CT · May 28, 2013#34It's a pretty quick and easy job with my test bench, so I would do them for $25 plus the cost to return them to you (which was about $7 to ship fnkngrv's today). While I am doing the update I will also program the VIN for you, which is stored in ECM.
thatbryanguyThread starterSC · May 29, 2013#35So upon a final attempt to double check everything and re-install the FIC I found the vacuum line going to the FIC was torn. Didn't know if that had anything to do with the problem but I knew it wasn't a good thing and would cause some vacuum leak problem so I replaced it. Put everything together and started it up. No problems! It ran, idle fluctuated back and forth a lot at first but that was to be expected after disconnecting the battery and with the 1zz TB. Took it for a test drive and it did just fine :) so I guess this adventure is finally over and I'm ready to move on to my Turbo adventure! Thanks to everyone who helped me out this past year with this issue!
thatbryanguyThread starterSC · May 29, 2013#36Well now the current issue is something g I need to deal with but at least I can drive it. Right now everytime I go into neutral from mid-high rpms the engine shuts off. Or if I sit idle too long the rpms very slowly keep dropping till about 600 then the engine stalls itself. It's strange but no codes or anything and I just start it back up and go. Every now and then it will rev itself all the way to 3000 rpm out of no where but then drop back down to 1000. Upon initial start up everytime it sputters and fluctuates a lot until I give it gas. It's interesting and will soon become annoying. Any thoughts? Strange settings on my fuel map maybe?
yariSB86OH · May 29, 2013#37Thats exactly what i'm dealing with. I've ordered an 08 ecu to install and see if that works. I've already checked for vacuum/boost leaks. The car runs fine when i bypass the FIC. New ecu should get here later this week, hopefully. So I can update once its here :)
Originally Posted by
thatbryanguy ↑ Well now the current issue is something g I need to deal with but at least I can drive it. Right now everytime I go into neutral from mid-high rpms the engine shuts off. Or if I sit idle too long the rpms very slowly keep dropping till about 600 then the engine stalls itself. It's strange but no codes or anything and I just start it back up and go. Every now and then it will rev itself all the way to 3000 rpm out of no where but then drop back down to 1000. Upon initial start up everytime it sputters and fluctuates a lot until I give it gas. It's interesting and will soon become annoying. Any thoughts? Strange settings on my fuel map maybe?
My car started to do that when I was running a 1zz throttle body, it started maybe 6months after install. I eventually put the stock tb back and never had the problem again. Now I'm boosted so no real need for it anyway.
thatbryanguyThread starterSC · May 30, 2013#39Yea I may go back to the 1nz TB just to see.
@yariSB86, yea I'm running the 08 ECU now and that's the current condition. I've bypassed it now since cranking the starter every stop light isn't something I wanna do...
fnkngrvIn The Hotbox · May 30, 2013#40Even though this ended up possibly not being the ECU I figured that I would chime in that I have received the flashed 07 ECU from Scott and will be installing it this weekend to see if it resolves my crank sensor issue when my FIC isn't bypassed.
yariSB86OH · May 30, 2013#41Yes totally want to know how that goes.
mazillaSan Jacinto California · May 30, 2013#42 Originally Posted by
thatbryanguy ↑ Well now the current issue is something g I need to deal with but at least I can drive it. Right now everytime I go into neutral from mid-high rpms the engine shuts off. Or if I sit idle too long the rpms very slowly keep dropping till about 600 then the engine stalls itself. It's strange but no codes or anything and I just start it back up and go. Every now and then it will rev itself all the way to 3000 rpm out of no where but then drop back down to 1000. Upon initial start up everytime it sputters and fluctuates a lot until I give it gas. It's interesting and will soon become annoying. Any thoughts? Strange settings on my fuel map maybe?
Originally Posted by
yariSB86 ↑ Thats exactly what i'm dealing with. I've ordered an 08 ecu to install and see if that works. I've already checked for vacuum/boost leaks. The car runs fine when i bypass the FIC. New ecu should get here later this week, hopefully. So I can update once its here :)
Originally Posted by
kou ↑ My car started to do that when I was running a 1zz throttle body, it started maybe 6months after install. I eventually put the stock tb back and never had the problem again. Now I'm boosted so no real need for it anyway.
Originally Posted by
thatbryanguy ↑ Yea I may go back to the 1nz TB just to see.
@yariSB86, yea I'm running the 08 ECU now and that's the current condition. I've bypassed it now since cranking the starter every stop light isn't something I wanna do...
This is why I mentioned "proceed with caution" in the thread recommending the 1ZZ ....
thatbryanguyThread starterSC · May 30, 2013#43The 1zz has worked great for a while now but just with this ECU swap its starting to act up :/
thatbryanguyThread starterSC · Jun 3, 2013#44I think I'm gonna try to send my 07 ECU to Scott, swap it back to that before I go back to the 1nz TB since the 1zz worked great till I swapped the ECU out now it acts up funny all the time even without the FIC plugged in. Update soon.
fnkngrvIn The Hotbox · Jun 3, 2013#45 Originally Posted by
fnkngrv ↑ Even though this ended up possibly not being the ECU I figured that I would chime in that I have received the flashed 07 ECU from Scott and will be installing it this weekend to see if it resolves my crank sensor issue when my FIC isn't bypassed.
As an update I wasn't able to get my ECU swapped out yet. Family obligations along with the weather than came through became stumbling blocks and I don't have use of my garage right now so hopefully in the next couple days I can spare some time from work.
thatbryanguyThread starterSC · Jun 4, 2013#46 Originally Posted by
fnkngrv ↑ As an update I wasn't able to get my ECU swapped out yet. Family obligations along with the weather than came through became stumbling blocks and I don't have use of my garage right now so hopefully in the next couple days I can spare some time from work.
Sweet thanks man!
DKN-YARISToronto · Jun 5, 2013#47Has anyone figured out exactly What the culprid behind the engine stalling with the fic plugged in? My yard is an '08 already so safe to say it's not the ecm. I'm running with 1zz injectors and after setting the response time higher to 810 the problem happens almost everyone I stop. If I bring it as low as 486us (default in the setup) it runs better but still stalls. Everything works fine when bypassed. So fustrated!!!!
thatbryanguyThread starterSC · Jun 6, 2013#48Are you running the stock throttle body or the 1zz throttle body?
DKN-YARISToronto · Jun 6, 2013#49 Originally Posted by
thatbryanguy ↑ Are you running the stock throttle body or the 1zz throttle body?
Running stock TB.
DKN-YARISToronto · Jun 6, 2013#50 Originally Posted by
thatbryanguy ↑ Are you running the stock throttle body or the 1zz throttle body?
Are you still getting the random misfire codes? I had it come up just once since i've been playing around with the car to figure out this stalling. I erased the code and its yet to come back...