Yarisworld Archive

AEM FIC fight for turbo!!!

135 posts · 50,829 views · page 2 of 3

Replies continued

yariSB86OH · Jun 6, 2013#51
I'm running 07 yaris manual transmission with stock ecu, new colder/shorter gapped spark plugs, 1zz fuel injectors, stock throttle body, 93 octane gas and i stall almost every time when i come to neutral if the FIC is plugged in. Only codes i get are, with the FIC plugged in, p0172. With the FIC bypassed i only get p0335.
DKN-YARISToronto · Jun 11, 2013#52
Originally Posted by yariSB86 ↑
I'm running 07 yaris manual transmission with stock ecu, new colder/shorter gapped spark plugs, 1zz fuel injectors, stock throttle body, 93 octane gas and i stall almost every time when i come to neutral if the FIC is plugged in. Only codes i get are, with the FIC plugged in, p0172. With the FIC bypassed i only get p0335.
I had one of the two CEL threw a few times, i changed the Camshaft position sensor and using the following settings:

AEM FI/C
x300 firmware
*z104 firmware (slave chip)
injector response set to 648us (using 1zz injectors)

*i'm currently trying all slave chip firmware to see which one has less of a harder time while starting the car. with z104 it takes a few tries before the car turns over.

I spent the past week and a bit trying to figure out what was causing the stalling as it only happens when the FI/C is plugged in leading me to believe it had something to do with firmware + settings making the car stall.
yariSB86OH · Jun 11, 2013#53
So here is my setup:

-Stock 07 ECU
-Stock throttle body
-1zz fuel injectors
-NGK iridium, shorter gapped spark plugs
-Zage turbo kit
-stock oil pan, "tapped" the upper oil pan assembly for return
-K&N oil filter, have a sandwich adaptor for oil pressure sensor and oil feed to turbo
-Royal Purple 5w30 synthetic oil
-Custom 2.25" turbo back exhaust

Lastly my FIC setup:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copyPicture not included in this copy

Does anyone see anything that would cause the car to stall out whenever in neutral? Feedback on anything is greatly appreciated also. Thanks everyone.
CTScottUSA, CT · Jun 11, 2013#54
Try clearing your 02 map.
yariSB86OH · Jun 12, 2013#55
Hey Scott, thanks for the advice. Unfortunately clearing out my O2 map failed horribly. Immediately threw p0102, MAF sensor bad. Clearing the code causes the car to shut off.

I am fairly certain none of my sensors are bad because with the FIC bypassed the car runs fine.
CTScottUSA, CT · Jun 12, 2013#56
Originally Posted by yariSB86 ↑
Hey Scott, thanks for the advice. Unfortunately clearing out my O2 map failed horribly. Immediately threw p0102, MAF sensor bad. Clearing the code causes the car to shut off.

I am fairly certain none of my sensors are bad because with the FIC bypassed the car runs fine.
I meant to also say - change it from voltage to percent. Making it all zeros as voltage wouldn't work.
yariSB86OH · Jun 13, 2013#57
What I did was change the maf map load input to tps voltage. Increased the amount slightly. Only near the area where the car idles. Left everything else zeros. As of a little driving yesterday I couldn't get the car to stall. Ill post a pic of the map and settings later today. My 08 ECU arrives today also. If I have time ill install it and see howl the car runs.
thatbryanguyThread starterSC · Jun 14, 2013#58
That's good news to hear. Let us know what you get from more driving
yariSB86OH · Jun 14, 2013#59
Car still stalls...I have the 08 ECU but won't be able to install it until Tuesday. Car runs slightly lean with the adjustments to the maf map. Won't be a problem to richen it back out.
That's where I stand right now...
thatbryanguyThread starterSC · Jun 15, 2013#60
Dang...I'm visiting my mom and haven't had any time to keep testing stuff right now. Has anyone sent their '07 ECU to get reflagged by Scott and tried it yet? As soon as I get a chance to ship it out ill do it but if anyone else has tried it yet itd be great to hear about it.
fnkngrvIn The Hotbox · Jun 15, 2013#61
I still haven't been able to actually test my flashed ECU with the FIC yet. I just got back from Fairbanks, Alaska and leave in another day for another week, this time to Ogden, Utah. Sorry! I have so much to get done in the next two days it is silly, but I will try to see about installing my FIC again. Since the ECU swap however it seems to me like the car does run smoother, but that could be a placebo effect as well.
DKN-YARISToronto · Jun 17, 2013#62
Ok boys and girls. I have spent the last week and a bit pulling my hair to try and figure out this stalling issue that some of us are having with the AEM FIC (zage turbo kit install or not) and using 1zz injectors.

After countless reading of threads and trying to conclude what everyone's settings are i finally figured out the problem for my car which i hope will do the same for some of those having the same stalling.

Over the weekend I put the car back on the dyno to try and simulate the same stalling under deceleration with no load. With that being said this ONLY happens when the AEM FI/C unit is plugged in, with the bypass harness installed, no problems no CELs.

After some thought and looking at my fuel map it finally hit me to do a straight comparison of the following:

AEM FI/C by passed, we monitored the following at IDLE:
IAT: 35 degress cel.
Short & Long term fuel trim: Averaging about -20-22%
APR: 14.9-15.3

With AEM FI/C plugged in, with my map i would see a HUGE difference in numbers pushing short and long fuel trim to over -30% causing it to stall out.

After looking, we decided to 0 out the fuel map from 3-21PSIA letting the stock ECM completely control deceleration AFR as I believe once you have settings inputted the stock ECM is not able to keep up trying to balance the AFR for proper idle set by stock parameters. I do believe very minor adjustments can be made but i figure the stock idles just fine i would just match those settings.

We attempted to make changes to the Injector response time but did not give any real results as increasing the number was giving worse results from what i was trying to match. the final number we came to was "688.5", 810us was throwing the system off a bit more than what i would like from stock. Do keep in mind this number may change for everyone depending on their setup, motor/injector condition.

We continued to keep an eye on the fuel trim but noticing a slightly higher combined avg than stock. we proceeded to making very minor changes to the MAF as the Zage kit does use a cone filter and the pipping size is a tad larger then stock. After making the adjustment, the idling readings matched stock fuel trim readings.

The one thing i did also try was all 3 firmware versions to see if any of them would produce any worse/better results as follows:

z104: cranking is best with 1 or 2 max tries and fires up but still stalls (30 mins of dyno)
z107: cranking is OK, 2-3 max tires and fires up but still stalls (30 mins of dyno)
z110: cranking is worst, usual 3 times max and fires up with NO STALLING. (1.5 hrs of dyno)

*Everytime i changed and tried new firmware, we did a calibration within the AEM FIC for the RPMS and TPS (just incase)

As results will vary from car to car, i do believe it would be best for those using the AEM FI/C to let the stock computer do what its supposed to do when it comes to the idle. (keep in mind this is probably why the car won't stall when you have the bypass harness plugged in) its too sensitive when the trying to balance out the system manually and the computer is not able to compensate for the difference quickly enough causing the idle. I think you can maybe go outside of stock range no more than 5-10% before it might start acting up.

Over the course of the time trying to find a possible solution and comparing the different setups here is what i currently have for those still trying to figure it out:

08 Yaris LB
-08 ECM
-Zage turbo kit
-1zz injectors
-stock TB (I replaced mine as i had previously adjusted the screw and wasn't sure if i had it back to the stock position so i picked up another one and clean it out completely and did not bother to touch the scew on the new TB.)
-Clean PCV
-Clean MAF
-HKS SSQV BOV which recirculates back into the Intake (I will disconnect the hose and see if any changes over the course of a week)

CELS SEEN after my install and gone after tweaking the FI/C:

Camshaft position sensor
Crankshaft position sensor
Idle control
Random Misfire + Cylinder Misfire

i've attached photos of my maps from my FI/C for reference. I hope this helps you guys out as it should be easy enough to do just driving around when you have your maps changed and should notice a difference. the biggest changelle was finding which firmware works best for YOUR setup. I have found that most use z107 vs. where i HAVE to use z110. Finding that perfect match between firmware should be done AFTER you have made changes to your maps to match what YOUR stock ECM fuel trim readings are and from there once you find the firmware that doesn't stall, that's your lucky number.

*Please ignore in my setup screen shot where i have the O2 start delay set a 3secs as i was trying to see if that would make any changes to my cranking issue :D Also, i did not change any values in my O2 Map as well.

As for the cranking issue i have found with the z110 firmware, i will try and shield some of the lines to see if cancelling out some of the noise in the lines will help the crank signal. its a difference problem now and AEM won't address it lol.

http://www.flickr.com/photos/30848488@N03/9068848391
http://www.flickr.com/photos/30848488@N03/9068843827
http://www.flickr.com/photos/30848488@N03/9068837109
http://www.flickr.com/photos/30848488@N03/9068830089
thatbryanguyThread starterSC · Jun 17, 2013#63
Awesome job, thank you for all the info! I'll jump on this within the week here hopefully and share my own results
Focus_Sh1ftNew Jersey · Jun 18, 2013#64
Very good information. Glad to see things are finally going well. Has the crank code came back yet on z110?
DKN-YARISToronto · Jun 18, 2013#65
Originally Posted by Focus_Sh1ft ↑
Very good information. Glad to see things are finally going well. Has the crank code came back yet on z110?
I only got the crank sensor code twice, both times was BEFORE i made any changes to FIC and only flashed it with z110 and it comes on after several long cranks as the ECM getting confused and throws the code.

*Correction, got CEL P0335 light on, camshaft position sensor, its always this CEL that gets triggered, I believe the signal line going to the AEM unit is noise causing the ECM to throw the code. I already replaced my sensor with a new one lol.

The only odd issue i'm seeing now is that when i start the vehicle (whether its 1 or up to 3 crank tries)

**Car now starts with just one crank like stock for the past 2 days....very odd.

I see get quite a bit of white smoke coming from the exhaust. from my AFR its at 15.2 on idle so its not running super rich i suspect it could be my oil feed causing the white smoke as it goes away after a bit of driving and when the motor/cat warms up...not sure if anyone has this issue with a zage kit and 1zz injectors?
thatbryanguyThread starterSC · Jul 26, 2013#66
Update!

So I got my 07 ECU back reflashed from CTScott, installed it back into my Yaris this morning and went for a drive. Brought my Hex wrench with me and had to adjust the idle a few times but then I hit the sweet spot and NO MORE STALLING at every red light or stop sign! I only went for a quick drive about 10-15 mins but so far so good! Seems the reflash did the trick to make the older Yaris ECU compatible with the AEM FIC.

This now finally means I will be hoping out of this thread (and hopefully never have to return again) and jumping into a Zage turbo kit thread! Oh how I've stared at that box with my turbo just waiting for so long...

:D
ShinareOklahoma City, OK · Jul 26, 2013#67
Congratz! Can't wait to see your turbo project thread. :)
thatbryanguyThread starterSC · Jul 29, 2013#68
Can anyone email me a decent base map to start with on 7psi? Just one where I can drive a little and not run lean the whole time. My email is thatbryanguy101@gmail.com
cali yarisCanoga Park, CA · Jul 29, 2013#69
emailed you two maps. 🙂
thatbryanguyThread starterSC · Jul 29, 2013#70
Originally Posted by cali yaris ↑
emailed you two maps. 🙂
Always lookin out :) you're awesome
thatbryanguyThread starterSC · Aug 27, 2013#71
Back again! Not sure now if its the FIC's fault this time though. So anyway...after driving around for a month with the turbo in and the FIC working well, AFRs are good and hitting just about 6psi, my car has decided in cant idle anymore again. It has also started spitting out whitish grey ( not positive on color) plumes of smoke after hitting boost then coming to a stop at a light or something of the sort. Changed my spark plugs for a step colder, NGK 7s, put some seafoam in the tank and it was decent for a day now it dies every stop or every time i go into nuetral really, unless as soon as I shift into neutral I let go of the brake and tap the gas. I have to keep tapping the gas so the rpm doesn't drop below 700. As soon as it hits 700 it stalls. The car has stalled a few times shifting out of gear into neutral for 2 secs going 30-40mph and I restarted the car by just putting it in 2nd and letting go of the clutch. Focusing on the rpms so much has taken a lot of my attention off the road and I've had a few close encounter with other cars because of it so I reaaally need to get this straightened out ASAP. Any ideas or help on the stalling?

Oh by the way, I changed the plugs because I started getting CELs saying cylinder misfires and idle control system malfunction. Haven't had those come back up since I changed the plugs. I've spent a lot of time adjusting the idle on the 1zz TB but somehow I think this is related to something else.
ilikericesavannah, ga · Aug 27, 2013#72
Have you tried closing the gap in the plugs? I think the stock gap is .44? try closing them to .33 or even .25

In my crx, After doing an WOT run it would sputter just a little bit in full boost (10psi). Afterwards, I would have a crappy Idle. I would clean the plugs and would idle fine until boost.

I think the plugs are getting blown out before fuel gets to them and then the fuel will soak the plugs causing your misfires.

Just a suggestion. Its a free modification to at least try. It won't hurt anything if it doesnt solve the problem
cali yarisCanoga Park, CA · Aug 27, 2013#73
I think you meant .044, .033 and .025 ?
thatbryanguyThread starterSC · Aug 27, 2013#74
Yea the NGK Brk7...something somethins are .033 gap, the last ones were .044. So it definitely runs smoother since I swapped those but I'll try closing the gap to .025 and see what's that does.

Side note I found that if I have the AC on, it will idle just fine at about 950rpms without stalling. My wife loves that part of my problem :/
ilikericesavannah, ga · Aug 27, 2013#75
Originally Posted by cali yaris ↑
I think you meant .044, .033 and .025 ?
Yea yea. Details....
thatbryanguyThread starterSC · Aug 27, 2013#76
The white plumes of smoke here and there freak me out in thinking my head gasket is leaking coolant in...my coolant levels are low but I haven't checked that in a good while so I'm not sure how long it's been low like that. Guess ill top off the coolant and see where it goes in the next few days
ilikericesavannah, ga · Aug 27, 2013#77
I can't imagine 6psi blowing a head gasket, but anything is possible I suppose. Do you have coolant running thru your turbo for cooling?
thatbryanguyThread starterSC · Aug 27, 2013#78
Nah not yet unfortunately...I've been trying to figure out what size fittings go to it so I can run a line.

Oh and it wouldn't have been the turbo blowing it directly, I've been having trouble keeping the crank pulley on tight under boost until I got it torqued way down with an impact wrench and at one point it came off and so the water pump wasnt going and the temp light came on but I was on a part of the interstate where I couldn't pull over for about a mile...so I'm hoping I didn't warp the head. It wasnt that long but I can imagine with the heat from the turbo everything heats up really quick in there.
fnkngrvIn The Hotbox · Aug 27, 2013#79
oh crap! yeah, could have done some damage in that scenario. best of luck!
ilikericesavannah, ga · Aug 28, 2013#80
Ohhh... yea.. that is quite possible.
thatbryanguyThread starterSC · Aug 28, 2013#81
So I was driving today and avoided hitting boost the entire drive for about 10mins to my bank. I then sat in the car and let it idle for 10mins without it stalling at all...so it seems it only has idling problems during a drive after I've hit boost. But if I don't hit boost again the after hitting boost once it will stall the rest of the drive until I shut it off for a while.
thatbryanguyThread starterSC · Aug 28, 2013#82
So upon further driving after the bank I noticed my radiator fan came on and then a few seconds after the car stalls out. Turn the key for the fan to come on and cool things a bit waited for it to turn off then cranked the car up again and as soon as the fan came back on it stalls again...hmm, electric load related?
fnkngrvIn The Hotbox · Aug 28, 2013#83
Do any of your gauges or lighting fixtures dim at all? Also you might want to meter your battery if possible when it happens if you can duplicate the issue and see voltage flares in either direction. Scott could have further advice.
thatbryanguyThread starterSC · Aug 28, 2013#84
Good call, I'll do that. I've got a spare brand new battery that I'm gonna switch out and see. After a drive from lunch just now it seems its getting slightly better. I put half a bottle of seafoamed in the tank and plan to use the other half in the vacuum lines thinking that when I was misfiring and all it ruined the old plugs, maybe there's a bunch of carbon build up in the cylinders that needs some cleaning out that's causing these strange idling issues.
cali yarisCanoga Park, CA · Aug 28, 2013#85
^ Pull a plug and look at it. That will tell you a lot about your AFR and your plugs.
thatbryanguyThread starterSC · Aug 29, 2013#86
So after topping the coolant off and watching it as the motor warmed up, I began to notice bubbles coming up to the surface of the antifreeze in the overflow resevoir...correct me if I'm wrong but that's usually a sure sign of blown head gasket as it pressurized the cooling system right?
mario98cPuerto Rico · Aug 29, 2013#87
Originally Posted by thatbryanguy ↑
So after topping the coolant off and watching it as the motor warmed up, I began to notice bubbles coming up to the surface of the antifreeze in the overflow resevoir...correct me if I'm wrong but that's usually a sure sign of blown head gasket as it pressurized the cooling system right?
It could be but I will do a leak down test just to be 100% sure before disassemble the engine.
thatbryanguyThread starterSC · Aug 29, 2013#88
Yea I'm gonna take it to a shop to get tested tomorrow morning. Ugh this is frustrating.
Focus_Sh1ftNew Jersey · Aug 30, 2013#89
Please, don't make the same mistake I made. Your head gasket is almost certainly fine. Some bubbles and metal shavings in your coolant/reservoir is also completely acceptable. Can you check compression?

I also had some serious overheating problems back when I first installed everything. At one point I had to drive almost 5 minutes with it on before I could pull over, so I can't imagine you did any damage.
thatbryanguyThread starterSC · Aug 30, 2013#90
Just took it to the shop and they say no leaky gasket or anything. Just got a bunch of misfire codes popping up again...ugh. Did a really quick idle test with the FIC bypassed and it idled fine. I just don't understand how it does fine for a month then suddenly decides to have issues. I'm currently sitting in my car right now and all of a sudden cant get it to die out like its been doing. What in the world is up with this car!
mario98cPuerto Rico · Aug 30, 2013#91
Originally Posted by thatbryanguy ↑
Just took it to the shop and they say no leaky gasket or anything. Just got a bunch of misfire codes popping up again...ugh. Did a really quick idle test with the FIC bypassed and it idled fine. I just don't understand how it does fine for a month then suddenly decides to have issues. I'm currently sitting in my car right now and all of a sudden cant get it to die out like its been doing. What in the world is up with this car!
Get rid of the Fic and buy an standalone ecu. Boomslang make the pulg and play harness for the aem ems-4. 😈
http://www.boomslang.us/aem-ems-4.ph...id=2&trans=all
thatbryanguyThread starterSC · Aug 30, 2013#92
Yea if I had a couple thousand bucks laying around I woulda done that already :/ on my current budget I kinda have to work with what I've got at the moment. Maybe one day I'll save up to get something like that but that's not a possibility in the near future
malibuguyWestminster, MD · Aug 30, 2013#93
Standaoone wont pass emissions either
fnkngrvIn The Hotbox · Aug 30, 2013#94
Hopefully you will get it hammered out soon bud. Just curious...do you have emissions testing in SC?
thatbryanguyThread starterSC · Aug 31, 2013#95
Nah no emissions in SC luckily. I'm gonna rework some of my sloppy wiring and tidy a bunch of stuff up and then go from there tomorrow. I've got some bad wiring habits that left my work needing to be redone so if anything strange dealing with electrical issues is going on I may be able to find it this way. By the way...my climate control knob lights are all out. Anyone know which fuse that is off hand?
DKN-YARISToronto · Sep 5, 2013#96
Originally Posted by thatbryanguy ↑
The white plumes of smoke here and there freak me out in thinking my head gasket is leaking coolant in...my coolant levels are low but I haven't checked that in a good while so I'm not sure how long it's been low like that. Guess ill top off the coolant and see where it goes in the next few days
I get this problem still, as i'm using 1zz injectors and having the FIC it dumps ALOT of extra fuel as I still have a hard time cranking the vehicle, mostly 2-3 tries before it starts. no stalling at all.

IF you are still getting the stalling with the FIC plugged in and only when under heavy load. try clearing all your maps and running all 3 firmwares. I was getting stalling even when all the maps where 0 and I found that z110 works the best for me. 107 didn't stall but gave me all kinds of CEL.
thatbryanguyThread starterSC · Sep 5, 2013#97
Well I'm about to get it smoked for a vacuum leak first then try messing with the FIC. Problem being all I have are Macs and no PC's so I can't readily use the AEM software at my house. I'm hoping its a small vacuum leak now just so I can fix that and be done with this mess. I just realized last night one big reason I think it may also be a vacuum leak is all this started almost immediately after installing my boost gauge so maybe I have a tiny hole in the gauge line or I messed something up while splicing it into the FIC's hose line. We'll see after the smoke test in the morning though
Focus_Sh1ftNew Jersey · Sep 6, 2013#98
It has to be a pretty large vacuum leak to be causing misfires. If nothing shows up, make sure you check the bov while the engine is running (hold your hand over the outlet and/or kink the manifold reference line).
thatbryanguyThread starterSC · Sep 7, 2013#99
It hasn't been misfiring since I replaced the plugs except for that one time I started it up and all those codes just popped up but haven't seen them again since. I sprayed some carb cleaner all around any areas in the intake system with the engine running and no change or reaction in idle. I haven't had the chance to take my a-pillar off and check the whole boost gauge line yet though and I haven't checked the actual BOV yet either. After that CTScott suggested possibly the alternator dying under voltage load or something along those lines but I've been to 4 places to get the battery and alternator tested and they all say its good.
DKN-YARISToronto · Sep 7, 2013#100
I can pretty much say that i tried pretty much all of what you are trying as i'm at a shop all the time. For those of us that have or had stalling issues with the FIC is that when its bypassed, EVERYTHING runs fine. has nothing to do with any leaks related to the install. If the car runs fine when FIC is bypassed, safe to say its related to the FIC unit itself and possibly other items when tuning at WOT.

When trying to figure out where to start i looked at all the options possible and put it down on pen and paper and started to eliminate factors one at a time. As i have corrected the stall issue now and after months of driving and even going on track, no issues at all...

As stalling shouldn't (and didn't happen for me) when the FIC is bypassed, it lead me to believe that during feedback mode, the stock ECM was having a hard time with the readings from what i could see on my AFR gauge as it was running pig rich. After i knocked all the maps back to 0, i ONLY adjusted the areas in boost and left everything outside of boost and during idle to 0 so the stock ECM can do what it needs as the ratio can't be too far off from what the stock ECM is programmed for.

Keep in mind, I was adjusting my injector response timing to 810us and left it at that. Firmware is the other buggy thing you will have to play with along the way. Thanks to CTScott who did help me along the way with a lot of answers based on what he had seen with this type of setup.

If i use z104, car runs fine but still stalls EVEN at right after start up at idle.
If i use z107, car doesn't run at all, starts, engine has CEL and misfire like crazy.
z110 has been the only working option i have considering the other 2 give me issue right off the bat.

the only issues i still have are:

hard cranking (2-3 cranks) this is clearly a noted problem with AEM and noise in the lines not giving off the right signal (even with the Boomslang harness)

White smoke at cold start up (smokes does go away after the cat is heated up)

CELs only come on after a series of attempts to start the vehicle, i'll get a cam position sensor error.

I've gotten maybe once a misfire code on my way to track but that is partial throttle the entire way and i've changed my plugs, i suspect the gap may need to be adjusted to hopefully correct that...

Even after a good month of running with no problems, i changed out the radiator with a Mishimoto rad, slim fan (puller) AND a pusher fan in front as the shroud from Mishimoto gave me some overheating issues when i had the A/C and even with a full load on the car, no stalling.

I hope you figure out what the stalling problem is as i know what it feels like and hope to save you as much time as possible!!!