Yea I haven't been able to mess with the FIC because of only having Mac's in my house. If have to get some time to borrow my brothers PC to make adjustments. And I haven't done a real test to see if bypassing the FIC alleviates the stalling issue, I bypassed it for a few mins in the driveway and it didn't stall but I didn't take it for a drive yet. I'll definitely be trying many of these things tomorrow though if I can. Thanks a bunch for the advice though! I'm running out of possible solutions haha
AEM FIC fight for turbo!!!
135 posts · 50,829 views · page 3 of 3
Replies continued
Ya, i'm hoping I can figure out what the root cause of the white smoke is as well. if its the injector setup there isn't much I can do as my tune is already at 90% duty cycle on larger injectors so the stock ones won't keep up for sure.
Did you also swap our your injectors?
Did you also swap our your injectors?
white smoke *could be oil backing up in the return line.
Would shortening the return line make any difference?Originally Posted by cali yaris ↑white smoke *could be oil backing up in the return line.
I tapped my block and got lazy during install and decided to not cut the line that came with the Zage kit but rather I just made it loop and everything fits haha.
It's not the length, it's the angle. It must be "downhill" to the pan, or if you did the fitting in the block you are probably ok (but there shouldn't be a low spot)
At the risk of sounding like a jerk the words "lazy" and "turbo" or "supercharger" should never be in the same conversation. That return line really needs to be a direct shot from point A to point B with no loops, etc.Originally Posted by DKN-YARIS ↑Would shortening the return line make any difference?
I tapped my block and got lazy during install and decided to not cut the line that came with the Zage kit but rather I just made it loop and everything fits haha.
Originally Posted by thatbryanguy ↑After that CTScott suggested possibly the alternator dying under voltage load or something along those lines but I've been to 4 places to get the battery and alternator tested and they all say its good.
Any of those places an actual alternator/engine electrical specialty shop?
ya, considering I've gotten the car to run now its time to clean up the areas I left as when I was putting in the motor getting some of the fittings and lines was a pain as no one stocked what I needed and was back ordered and my car was just sitting on the hoist.Originally Posted by fnkngrv ↑At the risk of sounding like a jerk the words "lazy" and "turbo" or "supercharger" should never be in the same conversation. That return line really needs to be a direct shot from point A to point B with no loops, etc.
Making a new line as we speak so hopefully that will fix the white smoke Issue.
^ sounds good. The fittings and lines seem to be a major PITA to procure for everyone. You always end up having to order what you need for the most part no matter where you live with only a few exceptions. Do you have an oil pressure gauge? I would be curious to know what you are seeing for activity with how you are set up now.
One of the places I went was a general shop, the others were autozone type places. And also me with a multimeter doing situational tests on the battery.
I'm not nearly as worried about the white smoke anymore now that I know I'm not burning coolant. I'm sure it's just the turbo burning some oil. I haven't tapped the block yet to receive the oil return line and I'm using the Zage pan so I do have a low dip in the line. I'm sure it's burning oil but that will get fixed a little later. For now I'll just keep checking my oil levels.
As for the stalling it no longer only occurs when the rad. fan comes on. It does seem to be trying much harder to stay on though when I park and have it idling in neutral. My belt seems to be sticking on start up now especially when I start with the AC on. It's progressively getting worse and worse of a squeal. Could my AC pulley be sticking and putting an extra load on it when it's not on? Causing it to not be able to idle properly?
I'm not nearly as worried about the white smoke anymore now that I know I'm not burning coolant. I'm sure it's just the turbo burning some oil. I haven't tapped the block yet to receive the oil return line and I'm using the Zage pan so I do have a low dip in the line. I'm sure it's burning oil but that will get fixed a little later. For now I'll just keep checking my oil levels.
As for the stalling it no longer only occurs when the rad. fan comes on. It does seem to be trying much harder to stay on though when I park and have it idling in neutral. My belt seems to be sticking on start up now especially when I start with the AC on. It's progressively getting worse and worse of a squeal. Could my AC pulley be sticking and putting an extra load on it when it's not on? Causing it to not be able to idle properly?
Doesn't oil burn blue? White smoke is from water (steam). Although, when I had my problem with the bov I had a lot of white smoke from misfires, but I never understood why (I wasn't burning coolant).
Also DKN-YARIS, check your intake piping to see if it's oily first. Otherwise, you're wasting time fixing something that isn't broken.
Also DKN-YARIS, check your intake piping to see if it's oily first. Otherwise, you're wasting time fixing something that isn't broken.
I had some belt sounds right after my install, the tension on the alternator wasn't good and I had to readjust it. Might want to try that first as I also put in a new belt seeing how my old one had some minor cracks in it. Also, when the AC is on, the RPMS will rise anyways to give it more at idle either way.Originally Posted by thatbryanguy ↑One of the places I went was a general shop, the others were autozone type places. And also me with a multimeter doing situational tests on the battery.
I'm not nearly as worried about the white smoke anymore now that I know I'm not burning coolant. I'm sure it's just the turbo burning some oil. I haven't tapped the block yet to receive the oil return line and I'm using the Zage pan so I do have a low dip in the line. I'm sure it's burning oil but that will get fixed a little later. For now I'll just keep checking my oil levels.
As for the stalling it no longer only occurs when the rad. fan comes on. It does seem to be trying much harder to stay on though when I park and have it idling in neutral. My belt seems to be sticking on start up now especially when I start with the AC on. It's progressively getting worse and worse of a squeal. Could my AC pulley be sticking and putting an extra load on it when it's not on? Causing it to not be able to idle properly?
Ya, I've checked my intake piping and I have a catch can with hardly any blow by.Originally Posted by Focus_Sh1ft ↑Doesn't oil burn blue? White smoke is from water (steam). Although, when I had my problem with the bov I had a lot of white smoke from misfires, but I never understood why (I wasn't burning coolant).
Also DKN-YARIS, check your intake piping to see if it's oily first. Otherwise, you're wasting time fixing something that isn't broken.
I put in a HKS SQVV BOV from day one and i'm not getting any misfires at all.
Going to put the new return line in tomorrow and give it a try over the weekend. If I start the car and drive, nothing, no smoke everything runs normal. If I start and let it idle for say even 3-5 mins and step on the gas, lots of white smoke which could very well be the return line as Garm has pointed out.
So AFRs read 13.1 at idle...too rich to stay on?
^ It should run like that at least; that's not crazy rich.
I've got to be misfiring still or something at idle...I smell gasoline periodically throughout my drives.
after a week or so of test driving with a new oil return line, white smoke issue is gone. thanks Gram!
So after unplugging my FIC and starting the car it immediately gave me a few dtcs. I got Maf circuit too low, and a few misfire codes. Bad Maf sensor? I may have a shop test my sensor to see if it's bad or something. Is the MAF circuit too low a hint to anything regarding my stalling out? I'm pretty sure it's misfiring all the time but it only gives me that code when I unplug the FIC and hook in the bypass. Checked my plugs and I have some pics of them. Wanted to see if anyone thought they looked anything but normal. I need to figure out this misfiring issue.
Can't upload them straight from my phone because the image size is too big I guess. I'll post a link to them when I get a chance.
Can't upload them straight from my phone because the image size is too big I guess. I'll post a link to them when I get a chance.
no real change, my Defi gauge shows 6.0 x100kPa when engine is cold. after its all warmed out, it will drop down to about 2.0/1.5. I have a mishimoto oil cooler installed as well so when i'm at the track it helps to keep everything in tack as the temp will make its way up a little bit.Originally Posted by fnkngrv ↑^ sounds good. The fittings and lines seem to be a major PITA to procure for everyone. You always end up having to order what you need for the most part no matter where you live with only a few exceptions. Do you have an oil pressure gauge? I would be curious to know what you are seeing for activity with how you are set up now.
Make sure your grounds are clean and tight. And check for corrosion and loose connections.Originally Posted by thatbryanguy ↑So after unplugging my FIC and starting the car it immediately gave me a few dtcs. I got Maf circuit too low, and a few misfire codes. Bad Maf sensor? I may have a shop test my sensor to see if it's bad or something. Is the MAF circuit too low a hint to anything regarding my stalling out? I'm pretty sure it's misfiring all the time but it only gives me that code when I unplug the FIC and hook in the bypass. Checked my plugs and I have some pics of them. Wanted to see if anyone thought they looked anything but normal. I need to figure out this misfiring issue.
Can't upload them straight from my phone because the image size is too big I guess. I'll post a link to them when I get a chance.
Good advice, I will check into that more. I went through and looked for a loose ground somewhere but couldn't find anything. I'll check again though. A guy on the AEM forums suggested I try all the different firmware versions because apparently each formware version applies better to different vehicles. I know DKN-YARIS went through all of the different firmwares so I'll refer back to that post. Another suggestion from someone because of my misfiring issue is to upgrade the coils? Has anyone had a problem with the stock ones with turbo? AEM High output inductive coils perhaps? Just think for such a basic turbo build it seems like overkill and it shouldn't be misfiring with my current setup.
Edit: ehh, just thinking about it and high output coils don't really make sense because I don't think it misfires when I bypass the FIC.
Edit: ehh, just thinking about it and high output coils don't really make sense because I don't think it misfires when I bypass the FIC.
If anything you could have a coil that is starting to break down or a misgapped plug. Upgrading the coils would really not be necessary.Originally Posted by thatbryanguy ↑Good advice, I will check into that more. I went through and looked for a loose ground somewhere but couldn't find anything. I'll check again though. A guy on the AEM forums suggested I try all the different firmware versions because apparently each formware version applies better to different vehicles. I know DKN-YARIS went through all of the different firmwares so I'll refer back to that post. Another suggestion from someone because of my misfiring issue is to upgrade the coils? Has anyone had a problem with the stock ones with turbo? AEM High output inductive coils perhaps? Just think for such a basic turbo build it seems like overkill and it shouldn't be misfiring with my current setup.
The best way to check for ground issues is with a multimeter. Put it in resistance (ohms) mode and measure between the negative battery terminal and ground points. Besides checking large metal chunks like the block, any wire that is white with a black stripe is a ground, and you should measure very close to zero ohms between it and the negative post.
Awesome Scott, I didn't know that about checking grounds. I guess I'll use that method to check as much as I can. As far as plug gap I re-gapped down from .032 to .029.
I'm almost positive it has something to do with the ECU fighting the FIC or something like that but I have very limited knowledge on how the FIC works and how the ECU responds. I just don't see it being an existing issue with my car since the car runs smooth and fine even at idle when the FIC is bypassed.
I'm almost positive it has something to do with the ECU fighting the FIC or something like that but I have very limited knowledge on how the FIC works and how the ECU responds. I just don't see it being an existing issue with my car since the car runs smooth and fine even at idle when the FIC is bypassed.
If it runs fine with the FIC bypassed, it would then point more to an issue with the FIC or the harness.Originally Posted by thatbryanguy ↑Awesome Scott, I didn't know that about checking grounds. I guess I'll use that method to check as much as I can. As far as plug gap I re-gapped down from .032 to .029.
I'm almost positive it has something to do with the ECU fighting the FIC or something like that but I have very limited knowledge on how the FIC works and how the ECU responds. I just don't see it being an existing issue with my car since the car runs smooth and fine even at idle when the FIC is bypassed.
For fuel control (which would be the most likely FIC behavior to cause misfires) the FIC monitors the signals from the ECM and adjusts the injector pulse length based on the map (making the injector squirt for longer, shorter or the same amount of time as the ECM is commanding).
If you load a blank map (all zeros) and the problem still remains, then the problem is likely hardware (FIC or Harness). If the problem stops with the zeroed map, then the issue is map related.
The map I'm using is the Rich map in the downloads section on Microimage. I haven't modified anything on it but figured I could use that rough tune to get me around until this next weekend or so when I get it on the dyno (little bday present from the wife!) so if anyone wants to look at that map and see if something is at all not the best for it the tune may end up solving everything. But I'll try to zero things out and see its effects if any.
.032 to .029.
I would go as low as .022
I would go as low as .022
I'm not sure I'm going to mess with the gap anymore because I'm 90% sure it has to do with the FIC itself just because when the FIC is bypassed the car doesn't misfire at all. So I figured as long as the car is getting the signal to spark, it does and doesn't have a problem igniting the mixture without the FIC.Originally Posted by ilikerice ↑.032 to .029.
I would go as low as .022
I hear ya. And you're probably right. I was just suggesting what gap I set mine. My crx had issues with loosing power at full boost. Is wasn't at bad when I went .033 and eliminated the issue completely at .022.
I am not saying this is the problem with your car. I am just adding my experience and what I set my gap when I was boosted.
I am not saying this is the problem with your car. I am just adding my experience and what I set my gap when I was boosted.
you mentioned a gas smell. make sure the injector cushions are seated properly or you will have misfire. Do you have a lightweight flywheel? that will cause false misfire codes.Originally Posted by thatbryanguy ↑Awesome Scott, I didn't know that about checking grounds. I guess I'll use that method to check as much as I can. As far as plug gap I re-gapped down from .032 to .029.
I'm almost positive it has something to do with the ECU fighting the FIC or something like that but I have very limited knowledge on how the FIC works and how the ECU responds. I just don't see it being an existing issue with my car since the car runs smooth and fine even at idle when the FIC is bypassed.
@blown_xa, I do have a lightweight flywheel but you can hear and feel when it misfires so I don't think its a false code unless it's just idling rough for some other reason and the misfire code is just a coincidence
@ilikerice, no I get ya, that's why I did try closing the gap a bit but it just seems more like the problem is from another area. I also don't have any problems with misfiring when I'm giving it gas or hitting boost, it's only when I let go of the gas and idle or put it in neutral that you hear and feel it misfiring.
@ilikerice, no I get ya, that's why I did try closing the gap a bit but it just seems more like the problem is from another area. I also don't have any problems with misfiring when I'm giving it gas or hitting boost, it's only when I let go of the gas and idle or put it in neutral that you hear and feel it misfiring.
Try zero's yet in the lower RPM range yet? Sounds like its too rich at idle
Haven't gotten to a PC yet but that is definitely one of my first things I'll try then I'll try all the different firmwares.Originally Posted by Bluevitz-rs ↑Try zero's yet in the lower RPM range yet? Sounds like its too rich at idle
My brother is helping me put together a junk PC tower tonight with a bunch of his random spare parts to use. I'll post with the results of the change as soon as I get that all done.
I finally got an old laptop to use to change my cal file on my FIC. So when I go to modify the fuel map on the cal file, what boxes should I make 0 for the lower rpms? I'm completely unfamiliar with how this works.
The car runs fines with a completely zero'ed out map (the base cal file) so I just need to know how exactly the FIC picks what boxes at idle. I see the rpms across the top but on the left it says psi so I'm not sure what to change.
The car runs fines with a completely zero'ed out map (the base cal file) so I just need to know how exactly the FIC picks what boxes at idle. I see the rpms across the top but on the left it says psi so I'm not sure what to change.
Update: Put in zeros for the boxes the FIC uses for idle and it helped a little it seemed with the roughness but it still stalls out at idle.
Bump for reference....