Yarisworld Archive

I'm going boosted!

109 posts · 23,209 views · page 2 of 3

Replies continued

yariSB86Thread starterOH · Apr 17, 2013#51
A-pillar from Glowshift usually $70, on sale when I bought it for $19.99
yariSB86Thread starterOH · Apr 18, 2013#52
Kit is here. Gonna start my pre install tonight.
yariSB86Thread starterOH · Apr 18, 2013#53
Getting started!

Picture not included in this copy
Picture not included in this copy
ilikericesavannah, ga · Apr 19, 2013#54
I can only feel 10% of your excitement.. I can only imagine yours.
Focus_Sh1ftNew Jersey · Apr 19, 2013#55
🤤

Also digging the gauge pod. That's a pretty decent fit.

Give us more pics! 😁
YodaFL · Apr 19, 2013#56
And so it begins.....
yariSB86Thread starterOH · Apr 19, 2013#57
Thanks guys! burning and turning hard with this install.

have a couple questions regarding the boomslang pnp harness.

first question is where does this inline fuse go(it is a 10amp fuse)? does it replace the 7.5 fuse labeled ECU-B?
Picture not included in this copy

next question is, these two wires look kinda important and I just want to make sure if I need them or not. one is white with a blue strip, the other is brown with black stripe.
Picture not included in this copy
fnkngrvIn The Hotbox · Apr 19, 2013#58
iirc I used a spare slot for my BSlang...I can try and see if I can get you better info...I currently have mine disco'ed. Yes, I am running without management, but have dropped my MV-S spring to the 3.5psi one until I upgrade my management. All I can say as well is be really careful with the lock arms as mine broke after only a year and removing/installing the harness a half dozen times.
fnkngrvIn The Hotbox · Apr 19, 2013#59
^ Nope...can't recall where I plugged it in. Perhaps Focus or CTScott can chime in if they can recollect. Sorry.
yariSB86Thread starterOH · Apr 19, 2013#60
Alright next question.

For the oil return, if I am not using the zage oil pan, what is the best way for doing this return line? (drilling a hole in my engine is almost out of the question)
cali yarisCanoga Park, CA · Apr 19, 2013#61
If you aren't using the Zage pan, drilling a hole and installing some fittings is the ONLY other option. Very nice pictures on our forums (and probably on here too).
yariSB86Thread starterOH · Apr 19, 2013#62
Damnit Garm :( I was afraid of that.

pm sent to you btw.
yariSB86Thread starterOH · Apr 19, 2013#63
so back to this:

Picture not included in this copy

its a wired in 10amp fuse pre wired on the AEM F/IC harness. where does it go?
yariSB86Thread starterOH · Apr 19, 2013#64
Turbo kit is installed.
Still need to:
Cut some plastic around intercooler piping
Tap the block for oil return...
Add oil
(Man my brain is fried, been working on this from 10am through 11pm.) can't think right now...going to bed.
Focus_Sh1ftNew Jersey · Apr 20, 2013#65
Originally Posted by yariSB86 ↑
so back to this:

Picture not included in this copy

its a wired in 10amp fuse pre wired on the AEM F/IC harness. where does it go?
My FIC harness didn't have that prewired. However, AEM likely revised their harness in the last few years to include it because people were probably hooking up their FICs unfused. Thus, if wired incorrectly - the unit gets fried, and AEM is left having to replace it.

As for where it goes, you have quite a few options at the fuse box in the engine bay. Ideally, you'll want to hook it up in place of another 10 amp fuse that only receives power on ACC or IGN. I'd check ECTS and EFI2 to see if they have voltage on key off, I can't remember.

Even if you have a constant 12v, the FIC has very little parasitic drain (pretty sure I actually have mine hooked up to a constant 12v).

Also, drilling the block - not as daunting as it sounds. Use the fittings I have in my guide, seal it up with some permatex, and you'll be fine.

Keep it up! It's worth it in the end 🙂
yariSB86Thread starterOH · Apr 20, 2013#66
Thanks focus. The fuse went to efi.
Gotta go shopping today, don't have the right drill for this.
yariSB86Thread starterOH · Apr 20, 2013#68
so I don't have to tap the block?
fnkngrvIn The Hotbox · Apr 20, 2013#69
Originally Posted by fnkngrv ↑
Here is a photo and yes I flipped it upside down to make it easier orientation-wise...haha 😁

Picture not included in this copy
I thought we have been over this already? You are not tapping the block. It is the Upper Oil Pan Sub-assembly. 🤷

You will want to tap the upper pan to prevent possible smoking in the future.
yariSB86Thread starterOH · Apr 20, 2013#70
Yes, I understand where the tap goes. Just seems like getting couple different answers about this.
I bought a small angle drill, tap set, some jbweld, silicone sealant, loctite, Teflon paste, and the fittings I am going I use. (Not sure what sealant is better)
Already have the hose(came with the zage kit) and clamps.

Now when I drill this hole, I'm going 1/2", what is the best way of making sure there are no metal shavings in my oil resevoir? Pour my used oil in and let it drain (do that a couple times)?
cali yarisCanoga Park, CA · Apr 20, 2013#71
I don't give a hoot what people call it. Pan, or block, makes no difference -- you will drill a hole and install a fitting. You can reach it easily from underneath with the pan off.

what is the best way of making sure there are no metal shavings in my oil resevoir?
You'll have the pan off, so I don't understand this question, sorry.
cali yarisCanoga Park, CA · Apr 20, 2013#72
^ You just have to be careful not to have a low spot or a kink in your return line. You are correct, the Zage pan is being used by some customers. I'd say it's about 50/50 from the kits we've sold.
yariSB86Thread starterOH · Apr 20, 2013#73
Sorry Garm, I totally spaced about taking off the pan...hah
yariSB86Thread starterOH · Apr 21, 2013#74
Ok, think I finally got all the right parts for this oil return install. Going to start with removing the oil pan :) (thanks Garm). Then prep the drill, make sure I have room. Then drill the hole. Wish me luck.
cali yarisCanoga Park, CA · Apr 21, 2013#75
good luck. It's aluminum, pretty soft, just be patient and you'll be fine!
yariSB86Thread starterOH · Apr 25, 2013#76
Hey guys. Sorry for no updates as I've been sick, and still am. Damn sinus infection.
Anyways, I've managed to get the oil return line finished. Waiting on the oil pan seal to cure. Double checked all my piping/couplers. Pretty close to first start up, won't be until Monday or Tuesday. I'm working all weekend. It's coming along. Slow and steady.
yariSB86Thread starterOH · Apr 27, 2013#77
I am in need of a base tune I can work off of. The car doesn't idle long enough for me to do anything. Does anyone have anything I can work with?
yariSB86Thread starterOH · Apr 30, 2013#78
So an update for how things have been.

Everything is installed and working as well as it can be for first start up.
No leaking oil, no exhaust leaks.
I need to pick up some heat shroud still. There is a really good place up the street that specializes in this so that's good.

I am having problems though. As I expected.

Only really big problem at the moment is that I need a good base tune to work with. The car doesn't idle long enough (maybe 20 seconds) for me to manipulate anything.

So I am going to ask anyone if they have a good base tune I can work with to just get things going.

Thanks
kounj · Apr 30, 2013#79
Are you using the aem fic? it should start and idle fine,did you install fic before turbo install or all at the same time?
cali yarisCanoga Park, CA · Apr 30, 2013#80
SB86, I'm emailing you a couple of base maps now.
kounj · Apr 30, 2013#81
Originally Posted by cali yaris ↑
SB86, I'm emailing you a couple of base maps now.
Send them to me also please to see if what I have made so far is going to work.
yariSB86Thread starterOH · Apr 30, 2013#82
@kou I am using the AEM FIC. And I did install everything at same time.

@Garm Thank you :)
kounj · Apr 30, 2013#83
Did you calibrate the fic? i am running all zeroed in all the maps and 810us for injector response time I am running NA to collect factory data for maf clamp and afr ratio voltages. Getting my downpipe made on sunday so should have some tuning info then.
yariSB86Thread starterOH · Apr 30, 2013#84
Garm, that richened tune runs good. I like the 11-10 range for 8psi. Car still doesn't idle. dies almost as quick as I can shift. Like ive I push the clutch in, the car will idle to stall. I don't get it...any suggestions?

also, when i uploaded that tune, my tachometer stopped working...
yariSB86Thread starterOH · Apr 30, 2013#85
I have not tried the bypass harness. yet.
kounj · Apr 30, 2013#86
Maybe BOV stuck open a little?
cali yarisCanoga Park, CA · Apr 30, 2013#87
I ran 8 psi with no tuning for 8 months. Didn't race or hit it hard, but the car ran "ok".
yariSB86Thread starterOH · Apr 30, 2013#88
@tolmach - I did tap the upper oil pan assembly

@kou - I'll check, but i doubt it.

@Garm - With your "leaned" tune the car runs 12.5-10.0 at idle...Is that the way you have it intended?
yariSB86Thread starterOH · Apr 30, 2013#89
Just started it up after it cooling down for a bit. with Garms "lean" tune it idles at ~14.5. Revd up to ~1500 it goes anywhere between ~13.5 - 11. When i lift off throttle it goes 10.0 - 20.0 then evens back to ~14.5-13.5

I can't test drive that yet, watching kids while the wife runs errands. But when i do, ill be sure and post the numbers.

Also Garm, are either of these tunes you emailed tuned with the 1zz injectors installed?
yariSB86Thread starterOH · Apr 30, 2013#90
@Tolmach, It was really soft, maybe 2-3mm. I used a 1/4" - 3/4" unibit. Drilled for 3/4". I attached a -8 AN bulkhead fitting. And i drilled above the oil line.
yariSB86Thread starterOH · Apr 30, 2013#91
So far with test driving it, I've only taking it up and down my street and side streets, no highway speeds. I have hit full boost (8psi) tho.

I'll do a quick run down of the few CELs I've gotten so far. First start up to now:
CELs 1-4 were spark plug related (b/c i changed mine out)
The next couple were AFR/O2 sensor related
And the most recent was a "too lean" code

The only really serious one was the too lean one, that was before i received the tunes from Garm. This code went away on its own after uploading the tune file i have on it now. (the lean tune)
yariSB86Thread starterOH · Apr 30, 2013#92
@kou The screw cap thing on the end of the BOV was loose. I hand tightened it and started up the car to a good idle. So maybe that was it combined with the tune file i have on the fic right now.
yariSB86Thread starterOH · Apr 30, 2013#93
@Tolmach I removed my oil pan and drilled from inside out. With an angled drill and that unibit i was able to but not fully get level, i was close enough. The bulkhead fitting along with the gasket type washers and the bulkhead nut, everything is pretty secure. Only oil residue i can see is coming from my oil drain plug, which ive tightened since finding it.
yariSB86Thread starterOH · Apr 30, 2013#94
Not a problem M8
kounj · Apr 30, 2013#95
Glad its working out. Now we need pictures.
yariSB86Thread starterOH · Apr 30, 2013#96
Ask and you shall receive :)

Picture not included in this copy

Picture not included in this copy
yariSB86Thread starterOH · Apr 30, 2013#97
I do plan on heat wrapping, there is a DEI just up the street.

The stock O2 sensor wire isnt stressed at all, infact i have it hanging with a zip tie to keep it off the exhaust manifold.

That steel braided hose is the oil in line. It is coming from my oil filter sandwich adapter.
yariSB86Thread starterOH · Apr 30, 2013#99
Whats this knob on the end of the BOV for? What is its function? I can screw it/unscrew it.

Edit: so that's the actuator control housing knob?

Picture not included in this copy
fnkngrvIn The Hotbox · May 1, 2013#100
Originally Posted by yariSB86 ↑
Ask and you shall receive :)

Picture not included in this copy
Wow...I really forgot how much it looks wide open front top to down on the backside when you are running an internal WG. I would get the heat wrap ASAP. Makes a big difference both performance and safety wise.