Replies continued
xnamerxxThread starterso cal · Nov 21, 2012#51It will but I'm a ways from being able to weld the bung in place. It might be difficult to extend the primary length for the WR header which is what you would want to do.
Thanks :)
tooterLos Angeles · Nov 21, 2012#52I only was thinking about lengthening the secondaries as its easier.
The logical place to cut would be at the first welded joint up from the bung where everything is pointing straight at each other.
Picture not included in this copy
Jason@SportsCarDebary, FL · Nov 21, 2012#53 Originally Posted by
xnamerxx ↑ I have dyno results from when I was stock, but I'm going to dyno it against a DC header after its been vetted.
LOL its going to be close but thats all I'm going to say 🙄
Another taste ;)
Good stuff, cant wait to see dyno numbers. 👍
xnamerxxThread starterso cal · Nov 21, 2012#54I don't think you'll see any benefits to doing so just because the primaries are far more important than the secondaries for base scavenging.
What I would do is cut the point before the primaries join get a u bend SS in the right diameter cut and bend it so the pipes sit on top of each other like a 4-1 and pull them out about 18-30"s and use the existing merges as a way to terminate the pipes.
Jason@SportsCarDebary, FL · Nov 21, 2012#55 Originally Posted by
tooter ↑ I only was thinking about lengthening the secondaries as its easier.
The logical place to cut would be at the first welded joint up from the bung where everything is pointing straight at each other.
Picture not included in this copy
Cut the tubes off at the flange and start over, it would be less work. 😆 A lot of fab guys hate coming in and trying to piece stuff together from an existing part - they seem to look at it as fixing the previous guys screw up. In the end the labor to piece together cost more than building from scratch.
tooterLos Angeles · Nov 21, 2012#56 Originally Posted by
Jason@SportsCar ↑ Cut the tubes off at the flange and start over, it would be less work. 😆 A lot of fab guys hate coming in and trying to piece stuff together from an existing part - they seem to look at it as fixing the previous guys screw up. In the end the labor to piece together cost more than building from scratch.
But
I'm the fab guy. 😉
Jason@SportsCarDebary, FL · Nov 21, 2012#57 Originally Posted by
tooter ↑ But I'm the fab guy. 😉
You are making it to easy. 😆 But hey, if you want to build another part with no appreciable gains for the hell of it. 😈
The only way to know is to try, worst case you cut up a relatively inexpensive header and waste a few hours.
tooterLos Angeles · Nov 21, 2012#58That's what life is all about... finding out. 🙂
xnamerxxThread starterso cal · Nov 22, 2012#59Well last update for a bit...I won't be able to start up on this project until next week as well as I need to get a few flanged cut to mate the 2 sections of pipe to allow installation. Again I wish I would have chosen a 4-1 design soo much easier to work with. I say this because the header path has a kink to the left and a quite narrow path that it needs to fit in.
Picture not included in this copy
tooterLos Angeles · Nov 22, 2012#60Wow...😲
Man, that's absolutely beautiful work. 👍
Are you using a jig, or the car itself for test fitting?
xnamerxxThread starterso cal · Nov 22, 2012#61No actually, its been mostly done by eye but i needed to make a few changes last night when i was test fitting it.
Autocross72Seattle · Nov 23, 2012#62Subscribe
vtencolumbus · Nov 23, 2012#63[QUOTE
Picture not included in this copy[/QUOTE]
wow me likey ...any chance you'd make an extra copy for me :P ?
this and a custom midpipe, 200 cells race cat, and custom central muffler with a dual twin outlet would be noiceee!!
awesome build sir 👍👍
xnamerxxThread starterso cal · Nov 23, 2012#64 Originally Posted by
vten ↑ wow me likey ...any chance you'd make an extra copy for me :P ?
this and a custom midpipe, 200 cells race cat, and custom central muffler with a dual twin outlet would be noiceee!!
awesome build sir 👍👍
Still working on that ;) Gotta make sure it actually makes power before I even start to think about making more.
1.5Tampa · Nov 23, 2012#65oooo already a prototype. Good work Namer.
4/20 NEVER FORGETPortland, OR · Nov 23, 2012#66Looks strangely similar to a dc header in that pic. :)
Awesome project, can't wait to see the finished product!
xnamerxxThread starterso cal · Nov 23, 2012#67Yeah i guess it kinda does...although i still need to add secondary pipes top it ;)
xnamerxxThread starterso cal · Nov 23, 2012#68Yeah i guess it kinda does...although i still need to add secondary pipes top it ;)
tooterLos Angeles · Nov 23, 2012#69 Originally Posted by
4/20 NEVER FORGET ↑ Looks strangely similar to a dc header in that pic. :)
It's a smart move to use a similar profile to the DC as it fits into the available space. 👍
xnamerxxThread starterso cal · Nov 23, 2012#70I didn't borrow from any existing designs, but with the given lengths I need to work with it just happened to follow their design.
Jason@SportsCarDebary, FL · Nov 23, 2012#71If you find yourself needing to test fit for clearance, my car is up in the air while I wait for the struts to be serviced.
xnamerxxThread starterso cal · Nov 23, 2012#72I might just take you up on that offer. Any idea how long the car is going to be down for service?
Jason@SportsCarDebary, FL · Nov 23, 2012#73 Originally Posted by
xnamerxx ↑ I might just take you up on that offer. Any idea how long the car is going to be down for service?
I would guess at least another week. But it is not getting raced again until Jan, so it would not be a big deal even after I get the suspension back in.
tooterLos Angeles · Nov 23, 2012#74 Originally Posted by
xnamerxx ↑ I didn't borrow from any existing designs, but with the given lengths I need to work with it just happened to follow their design.
I know. It's the available space that defines the shape, so all the headers are constrained to follow the same basic conforming profile.
When you get it done, post a video of how the engine sounds with the open header. I bet it'll sound awesome! 👍
xnamerxxThread starterso cal · Nov 24, 2012#75I've got an ideal length to work with so in order to hit that ideal length while staying within the constrains of the chassis. My bends aren't quite as smooth as the DC since I've got to hit certain lengths so my bends snake a little bit which you don't quite see in the pictures.
I just decided to have the primaries terminate in about the same location as the stock header. The secondary is going to have some of that snaking as well just so I can get a few extra inches of tube length.
I'll make sure to give you a video after everything is said and done :)
Jason@SportsCarDebary, FL · Nov 24, 2012#76Test fit. Looks good so far.
Picture not included in this copy
Picture not included in this copy
4/20 NEVER FORGETPortland, OR · Nov 24, 2012#77That looks awesome! Primary length looks fantastic.
Hey, quick question. How many wires does the secondary o2 sensor have? (the sensor after the 1st cat) Thanks!
xnamerxxThread starterso cal · Nov 24, 2012#784
tooterLos Angeles · Nov 25, 2012#79It looks like the tubing is oriented very nicely... 🙂
By the way, what mm inside diameter tubing are you using? And had you considered using twin runner bolt on connector plates similar to this one to make your header two-piece?
Picture not included in this copy
xnamerxxThread starterso cal · Nov 25, 2012#80The 2 halves will be flanged so it can be installed.
The tubing diameter is 1 3/8 for the primaries.
malibuguyWestminster, MD · Nov 25, 2012#81looks good. where are you going to locate the flex joints?
ive still havent decided if i want to build one as well, or go turblose. if the motor seems to respond very well to your header, i may stay n/a
tooterLos Angeles · Nov 25, 2012#82 Originally Posted by
xnamerxx ↑ The 2 halves will be flanged so it can be installed.
The tubing diameter is 1 3/8 for the primaries.
That's just about the same as the 36mm Weapon R tubing. I'm really curious how much you'll gain by the longer runners. You definitely have the principles of performance working in your favor. 🙂
xnamerxxThread starterso cal · Nov 25, 2012#83Its going to terminate at the flexjoint. There is only so much power that the exhaust, but with that being said there is a serious restriction with the exhaust. This mod will really pair well ecu tuning so I may not see a whole lot of power over existing ots headers, I should see a ton more torque over any of the existing pieces which is one of the reasons I decided to build this.
Bluevitz-rsOshawa, Ontario, Canada · Nov 25, 2012#84I'm quite certain you're going to snap the header if you move the flex joint that far down the line. The reason the joint is where it is, is because of the engine movement. If you try and move it that far down, it'll either break away at the head or break the joint where the stock flex joint should be located.
cali yarisCanoga Park, CA · Nov 25, 2012#85Picture not included in this copy
xnamerxxThread starterso cal · Nov 25, 2012#86The stock motor doesn't have a flex joint, it uses a ball and socket joint. The reason the joint is located where it is stock is because that's the easiest and cheapest place to put it. There does have to be some flex in the exhaust and ideally it should be as close to the motor as possible but you work with the space you're given.
The exhaust itself is hung which allows some movement there so the only reason you even need flex in the exhaust itself is to reduce the wagging motion of the main pipe and reduce load from the header. If you look at the header there is a support beam the bolts to the block and the header and that's what's carrying most of the fore and aft load from the header which is another reason why the ball and socket is located where it is. I've done some analysis on this I have an idea of where the load is sitting. If the side bracket isn't in place all of the load will sit on the flange and the failure will be located on the flange, if the side bracket is in place the pipes are thick enough to handle most of the load but the secondary flange will still be taking some load under movement but its substantially less with the flex joint in place. So to get some flex I chose a flex joint over a ball and socket because its easier for me to incorporate it the multiple center section exhausts that I have.
1.5Tampa · Nov 26, 2012#87😁
xnamerxxThread starterso cal · Nov 28, 2012#88Well the primaries are all welded up so I'm stuck waiting for my new flange to be made but once I get that piece it'll be finished quickly.
xnamerxxThread starterso cal · Nov 28, 2012#89Picture not included in this copy
So nice and purdy 🙂
tooterLos Angeles · Nov 28, 2012#90🤤🤤🤤
When you weld stainless steel, does the electric welder need to use any gas?
xnamerxxThread starterso cal · Nov 28, 2012#91I can't directly comment since I'm a pretty terrible welder but SS requires a different kind of gas and filler material.
I guess it depends on if you're using a Flux weld material or MIG/TIG welding. If its MIG or TIG you need gas otherwise it'll splatter and sugar really bad plus just weld like crap.
I think this might be helpful (
http://www.brazing.com/techguide/pro.../stainless.asp)
ViperoniBrampton, ON · Nov 28, 2012#92 Originally Posted by
xnamerxx ↑ Picture not included in this copy
So nice and purdy 🙂
Lookin good!
xnamerxxThread starterso cal · Nov 30, 2012#93Here are my baseline numbers. The car is stock aside from a DC header, MI pulley, and a K&N air filter.
I'm guessing Toyota breathed a little extra magic on my car when it was made.
Also an acceleration run in 2nd gear from 12-62 mph. Just to get an idea of vehicle acceleration, another thing to add aside from dyno numbers.
http://www.youtube.com/watch?v=dquJk...&feature=g-upl Picture not included in this copy Bluevitz-rsOshawa, Ontario, Canada · Nov 30, 2012#94Looks like they did a 2nd gear pull. Makes the numbers inflated, but it's only for comparison. As long as you use the same dyno.
xnamerxxThread starterso cal · Nov 30, 2012#95Yeah, Church's is known to dyno high as well, I think he uses a gear correction for torque to negate which gear the pull was made. The numbers just seemed high to me even if I took 15% off.
I got a kick out of it because I was making the same amount of power as Jason up until his cams started doing their thing.
BTW my motor has 100k on the clock so it shows how impressive these engines are even after a long life of use.
Jason@SportsCarDebary, FL · Nov 30, 2012#96 Originally Posted by
xnamerxx ↑ Yeah, Church's is known to dyno high as well, I think he uses a gear correction for torque to negate which gear the pull was made. The numbers just seemed high to me even if I took 15% off.
I got a kick out of it because I was making the same amount of power as Jason up until his cams started doing their thing.
BTW my motor has 100k on the clock so it shows how impressive these engines are even after a long life of use.
I was 132hp on that dyno with a stock motor, just had an ECU on you. My pulls were in 3rd gear.
xnamerxxThread starterso cal · Nov 30, 2012#97Hmm, he showed me a side by side and there was a big boost at 5k or so, and he said it was because of the aftermarket cam.
Jason@SportsCarDebary, FL · Nov 30, 2012#98 Originally Posted by
xnamerxx ↑ Hmm, he showed me a side by side and there was a big boost at 5k or so, and he said it was because of the aftermarket cam.
Not sure what he showed you, but it had to be old if the number was that low. Likely from when we first got the car and had the camcon. And none of the cams have made low end, they all lost tq, they dont start to make power till way up high.
xnamerxxThread starterso cal · Nov 30, 2012#99No the number was way higher than mine but the curves were really similar up until 5k or so than yours sort of shot up by 15 or so and kept climbing.
Jason@SportsCarDebary, FL · Nov 30, 2012#100 Originally Posted by
xnamerxx ↑ No the number was way higher than mine but the curves were really similar up until 5k or so than yours sort of shot up by 15 or so and kept climbing.
I misunderstood. Yeah most of the stuff we did to the engine would not help for autocross, we just could not find tq. Maybe your header will change that.