Replies continued
BailOutThread starterReno, Nevada, USA · May 8, 2009#101 Originally Posted by
Darb ↑ Whoa whoa, question. Doesn't the AT require you to be in park (P) in order to restart the engine?
Hello Darb,
No, you can start it from N(eutral) as well. However, if you would like to do it from P(ark) you still have your power brakes after the engine is off for at least 4 touches.
MarthosNEPA · Aug 4, 2009#102Lets make this simple.
DFCO is for slowing and/or stopping the car,
If you need to stop at the bottom of a hill, or you want to go slower down a hill, DFCO is for you.
Start down the hill, Auto Trans people may need to tap breaks or even downshift into 3, Manual people just let off the fuel pedal.
The engine will start to try to slow the car, at this point your not using ANY GAS (DFCO).
When at or near the bottom apply brakes, when stopped put trans back into D (which is really OD). If you were just slowing the car some, just pop it back to D and hit the go pedal!
You saved gas.
If you were to bump the car into neutral, all the stopping would be on your brakes and the engine would Idle (use some gas) all the way down.
If you need to coast after the bottom of said hill, DFCO is not for you! Coasting on flat ground requires forward momentum, DFCO Scrubs forward Momentum.
If DFCO slows the car to much and you find yourself back on the Go Pedal before the bottom, you are not saving gas.
DFCO stops your fuel injectors from injecting fuel into the cylinders.
Originally Posted by
Marthos ↑ Lets make this simple.
DFCO is for slowing and/or stopping the car,
If you need to stop at the bottom of a hill, or you want to go slower down a hill, DFCO is for you.
Start down the hill, Auto Trans people may need to tap breaks or even downshift into 3, Manual people just let off the fuel pedal.
The engine will start to try to slow the car, at this point your not using ANY GAS (DFCO).
When at or near the bottom apply brakes, when stopped put trans back into D (which is really OD). If you were just slowing the car some, just pop it back to D and hit the go pedal!
You saved gas.
If you were to bump the car into neutral, all the stopping would be on your brakes and the engine would Idle (use some gas) all the way down.
If you need to coast after the bottom of said hill, DFCO is not for you! Coasting on flat ground requires forward momentum, DFCO Scrubs forward Momentum.
If DFCO slows the car to much and you find yourself back on the Go Pedal before the bottom, you are not saving gas.
DFCO stops your fuel injectors from injecting fuel into the cylinders.
Exactly what I have found. If I don't need to slow on the hill or at the bottom I hold just enough pressure on the accelerator to prevent DFCO to gain momentum for the flat or the next uphill if safe to do so.
One of my favorite features about the Yaris AT is it is very user friendly in regards to engine braking. Down shifting/upshifting are very easy and effective due to DFCO and the way the shifter is set up.
R2
Yaris HiltonBristol, Tennessee, USA · Aug 4, 2009#104The AT downshifts to hold back the coasting car if you touch the brake. Touch the gas and it upshifts to coast freely.
MarthosNEPA · Aug 8, 2009#105Also, the tranny will not down shift till rpms are safe.
I have tried it on a 1/4 mile, big downhill grade leaving my home lots of times, with a stop sign at the bottom.
i pop it into 3rd going 40, and it downshifts right away and revs ups a tiny bit, when i pop it into 2nd it almost always downshifts right away (2nd goes past 50mph if ya floor it from a stop) rpms go up, sounds kinda cool, then when im at around 25 i pop it to 1st and have to hit the brakes for it to downshift. I think it shifts down when im around 18 to 20 mph.
I dont have a tach, but I am sure it never revs past 5k after it downshifts, I think there is some kinda over-rev saftey lock out possibly?
The whole process seems very nonharmful to me, and i know im saving a little gas and a lot of brakes.
MarthosNEPA · Aug 8, 2009#106Tested this today while cold light was on and when popping into first at 25 mph it went right to 1st gear, still dont think it reved much maybe 4k.
Edit = I guess i should mention, this is a steep hill, im on the brakes pretty good when I did shift it to 1st, revs droped fast, I have no tach and am guessing at the rpms.
Edit = Tried again cold light on, into 1st at 30 and it shifted right away, the trans acts totally different when the cold light is on, wonder if this means the shift points could be remapped?
MarthosNEPA · Aug 9, 2009#107Guess I can quit testing, found this in owners manual.
Pg 126 (c) using engine braking
"The transmision will downshift to second gear when the vehicle speed drops down to or lower than 53 mph."
First gear is 26 mph.
GMKingPortsmouth VA · Aug 31, 2009#108I just bought my toyota yaris this last friday and I love it, but one thing has been bothering me and I think it may be this DFCO
when I coast my vehicle (automatic, btw) without going into neutral it seems to "drag" kind of like engine braking, but when I coast it in nuetral there's no drag. I was wondering is this "drag" the DFCO? and if it saves on fuel then why does it cause the vehicle to slow down at a faster rate than in neutral?
Yaris HiltonBristol, Tennessee, USA · Sep 1, 2009#109Yes, it's the DFCO. Yes, it slows down the car faster than coasting in neutral, because the car's momentum is spinning the engine with no power being generated, just drag. It's not meant for increasing gas mileage, but for eliminating exhaust emissions while the car is coasting. If it's coasting down a steep enough hill to overcome the drag, you're saving gas over having the engine still running at idle power. If you're on level ground, you'll save gas whenever you're coasting toward a stop and would be using the brakes sooner without it. But it won't always save gas. Under conditions where it makes you slow more than you want to and you have to give it more gas to make it up, you may lose a bit.
GMKingPortsmouth VA · Sep 1, 2009#110exactly the issue i've been having. the fact that it slows down quicker as I'm trying to coast really aggravates me, screw emissions, I'm trying to get somewhere, guess I'm just gonna have to get into the habbit of putting in neutral
Yaris HiltonBristol, Tennessee, USA · Sep 1, 2009#111I've gotten used to the DFCO and pay little attention to it. But at the moment I'm travelling with the family in my old minivan that doesn't have DFCO, and it's startling how slowly it decelerates on flat ground with the engine idling! I have to use the brakes a lot more.
09YarisguyAustin, TX · Sep 2, 2009#112I appreciate this thread and forum...I had no idea my new car had this system so I've been throwing it in idle on long downhills or rolling to a stop and being proud of the 38.5 MPG average I've gotten so far. I will try this with my next tank for comparison and let you know exactly what this does for me.
Just FYI though, there are a few places I'll still be coasting since there's a couple of half mile lengths on the highway where I can roll without losing any momentum. I figure I save a bit on gas for idling instead of gassing and I get a nearly free mile out of each trip to work.
BailOutThread starterReno, Nevada, USA · Sep 2, 2009#113It sounds like you're off to a great start, 09Yarisguy. 👍
127.0.0.1NE · Oct 20, 2009#1142010 yaris 5dr HB,
I find that scangauge cutoff set to 16 most accurately represents DFCO and 21 did not.
21 reported 9999 when I was not DFCO, merely foot off gas at 60mph which is not DFCO...there is still some fuel running to keep my decel rate from dropping too much. 16 now it never misreports.
I watched TPS. TPS lowest number is 15, but DFCO still will not always occur at TPS 15. But DFCO cannot occur anywhere
16 or above, so cutoff at 16 is perfect. when i drop to 15, scangauge reports some high mileage 180 or so, but won't
flash me the 9999 until I feel (with me arse dyno) the actual DFCO condition. so...I think...at least for my piglet, cutoff 16 is accurate.
Yaris HiltonBristol, Tennessee, USA · Oct 20, 2009#115Foot off gas at any speed with the torque converter locked up and engine spinning over about 1000 RPM puts mine into DFCO. I can feel the sudden small increase in drag after about 1/2 second.
jtcoopClemmons, NC · Oct 22, 2009#116OK everybody I bought a Kiwi MPG and now I am having difficulty seeing or believing the DFCO theory. Traveling at say 40 mph going down hill, I let off the gas and the IMPG reads 165 MPG. If I push the clutch in the reading jumps to 180 or higher. The more speed I gain going down a hill with the clutch in the higher the IMPG reads. I have even tried tapping the brakes. Am I missing something? I will try and see what the LOD reading are tonight. I know at idle the LOD reads 16. I am not sure what it reads when I take my foot off the accelerator at 40 mph versus foot just touching the accelerator.
Regardless I am looking forward to my further education on the subject.
Yaris HiltonBristol, Tennessee, USA · Oct 22, 2009#117DFCO's not a theory. If your Scangauge isn't showing it, it's improperly set.
jtcoopClemmons, NC · Oct 23, 2009#118For those who have a Scanguage, ( I do not ), when it is displaying Instant Gas Mileage, you take your foot off the accelerator, you get a large increase in the MPG being displayed. If you depress the clutch, do the numbers go up or down. With my experience it is going up. I, like most am trying to get the most bang for the buck. It makes sense to me that if the numbers go up with the clutch depressed, then I am getting more bang.
Yaris H, could something be wrong with the car? I am trying to find someone in my area that has a Scanguage to compare the IMPG.
Yaris HiltonBristol, Tennessee, USA · Oct 23, 2009#119I doubt anything's wrong with the car. DFCO's supposed to kick in after about 500-700 milliseconds. Are you waiting for it? You don't need a Scangauge to feel the sudden drag, it slows the car down.
127.0.0.1NE · Oct 23, 2009#120DFCO kicks in when
there is something in the transmisson keeping the engine spinning so the engine
doesn't actually stop turning
and when
the decel rate DFCO will make won't spill your coffee. it is programmed to kick in
but not make it buck. hence...in an automatic, it won't always kick in when foot
is off gas.
Yaris HiltonBristol, Tennessee, USA · Oct 23, 2009#121 Originally Posted by
127.0.0.1 ↑ the decel rate DFCO will make won't spill your coffee. it is programmed to kick in
but not make it buck. hence...in an automatic, it won't always kick in when foot
is off gas.
It never makes it buck. But you can feel a small jerk when the fuel cuts out. It's definitely slowing down. The automatic usually has the torque converter locked when you're cruising around at light throttle, even poking around town at 25 MPH. Watch the tach. When the torque converter's unlocked, the engine speed will swing up and down with more or less pressure on the throttle. With it locked, the RPMs stay in strict lockstep with the speed on the speedometer.
Older automatic Yarises before mid-2007 model year may not have DFCO in Drive.
jtcoopClemmons, NC · Oct 24, 2009#122When the RPMs reach 1100 and I actually feel the fuel cut back on, if I just let the car continue to coast. So I am pretty confident DFCO is working. I did notice today that the Load was reading 18 at one point on a long down hill run on the expressway. When I depress the clutch it went to 16. I thought I read somewhere in this post that Load had to be at 15 or 16 before DFCO would start. Right or wrong?
Everybody I again just want to say "Thank you" for your patience!
My bad....just reread very first post! Bail Out answered the Load question
Yaris HiltonBristol, Tennessee, USA · Oct 24, 2009#123Mine doesn't seem to kick in DFCO below about 1100 RPM, but also doesn't kick it back to idle power till it drops below about 800 RPM on the tach once DFCO's on. (I think at the same time it unlocks the torque converter.)
jjonroflMaryland, USA · Dec 16, 2009#124I've read most of these and think I finally know what it is- is it when I go down a steep hill going about 40-45, and when I touch the brakes, it buzzes and begins to brake steadily down the hill? If so, should I try to make this happen?
BailOutThread starterReno, Nevada, USA · Dec 16, 2009#125 Originally Posted by
jjonrofl ↑ I've read most of these and think I finally know what it is- is it when I go down a steep hill going about 40-45, and when I touch the brakes, it buzzes and begins to brake steadily down the hill? If so, should I try to make this happen?
You don't have to touch the brakes to make it kick in. It will happen by itself shortly after you take your foot off of the gas pedal.
jjonroflMaryland, USA · Jan 1, 2010#126Brian- then what is the noise the engine/transmission/something makes when I begin to brake at about 45mph down a hill? And the car stays at about 40mph?
supmetSouthern California · Jan 1, 2010#127 Originally Posted by
jjonrofl ↑ Brian- then what is the noise the engine/transmission/something makes when I begin to brake at about 45mph down a hill? And the car stays at about 40mph?
DFCO doesn't make a noise, it just sounds like the engine revving from a downshift.
I'm not sure what the buzzing you are talking about is.
Yaris HiltonBristol, Tennessee, USA · Jan 1, 2010#128DFCO doesn't make a noise, and it doesn't rev the engine or downshift an automatic transmission. There's just a sudden slight deceleration as the idle fuel is cut off. You have to be paying close attention to feel it.
There is a separate function in the ECU that downshifts the transmission if you're coasting downhill and apply the brakes. It increases the "engine braking" so you don't have to use the brakes as much. Touch the gas pedal and let it off, and it'll upshift to high gear and let you pick up speed coasting.
jjonroflMaryland, USA · Jan 2, 2010#129Ah you're right, it must be the engine braking. is that bad for gas mileage? 😉
jjonroflMaryland, USA · Jan 20, 2010#130I still don't understand DFCO.. if it's seamless and you don't have to do anything, then how do you do what you said in the instructions?
"As soon as you hit an exit ramp off of the highway go into DFCO all the way to the end of the ramp." By doing what? Driving like you would normally?
Yaris HiltonBristol, Tennessee, USA · Jan 21, 2010#131Exactly. Lift your foot off of the gas.
127.0.0.1NE · Jan 21, 2010#132 Originally Posted by
jjonrofl ↑ I still don't understand DFCO.. if it's seamless and you don't have to do anything, then how do you do what you said in the instructions?
"As soon as you hit an exit ramp off of the highway go into DFCO all the way to the end of the ramp." By doing what? Driving like you would normally?
yes it just means take foot off gas, so that
if the conditions are correct for DFCO, it will kick in.
it will not kick in if
you shift to neutral
or
have any gas pedal input
it really doesn't matter a ton for real world, single use... other than reduce emissions a little bit, and improve mileage a very little bit.
but over the life of the car x how many cars have DFCO, it matters a lot...the end user doesn't need to know
squat about it, it is computer controlled.
the end user can induce DFCO conditions more often than 'natural driving' would
by adjusting how they use the kinetic energy of the vehicle, and the gas pedal and gear choices.
why?harnett county NC · Jan 22, 2010#133it can improve gas mileage a lot if you plan to use it.
Yaris HiltonBristol, Tennessee, USA · Jan 22, 2010#134Keeping your foot off the gas usually does. 🙂
FalconiaFinland · Feb 25, 2010#135I just read ecomodder 100+ Tips for better fuel efficiency and I saw this:
Originally Posted by ecomodder.com
Braking tips ...
44) The most efficient way to slow down
When you *have* to slow down, here's an approximate heirarchy of methods, from best to worst.
1) coasting in neutral, engine off (ie. roll to a stop);
2) coasting in neutral, engine idling;
3) regenerative coasting (hybrid vehicles)
4) regenerative braking (hybrid vehicles)
5) coasting in "deceleration fuel cut-off" mode (in gear, above a certain engine RPM)
6) conventional friction braking (non-hybrid or hybrid)
Choosing the right method depends on traffic conditions (following vehicles) and how quickly you need to stop.
REALLY?! Is it really more efficient to coast in neutral, with engine idling than using DFCO?! I thought DFCO cuts the fuel and it is better way to slow down...
BailOutThread starterReno, Nevada, USA · Feb 25, 2010#136 Originally Posted by
Falconia ↑ REALLY?! Is it really more efficient to coast in neutral, with engine idling than using DFCO?! I thought DFCO cuts the fuel and it is better way to slow down...
Hello Falconia,
There are times and places for both techniques. If you only have a short distance to worry about, or you are going downhill, or you know you are likely going to stop then DFCO is best as it allows you to decelerate without fuel usage.
But if you would rather maintain more of your speed over a longer distance then coasting in neutral is better as it takes much less fuel to idle for a short while than it does to re-accelerate from a major momentum loss.
forgedinflame92311 · Mar 3, 2010#137It's a good read, and I'll definitely pay more attention to how the car performs.
BTW, New guy here. Congrats on the sweet community you guys have made and I'm glad to add myself to it, I've already read tons of great tips.
pawsplusColumbia, TN · Mar 5, 2010#138So . . . on the MT, avoid downshifting?
LorenSafety Harbor, FL · Mar 5, 2010#139 Originally Posted by
pawsplus ↑ So . . . on the MT, avoid downshifting?
Downshift when you need to when cruising or accelerating. (like if you don't have enough power to get up a hill in the gear you're in)
Delay downshifting on deceleration to prolong your DFCO coast. (downshifting earlier gives you more engine braking, which you don't want if you're trying to coast as long as possible "for free")
pawsplusColumbia, TN · Mar 5, 2010#140Alrighty! Thanks!
Oh, and I'm assuming that my goal is to stay around 2000 rpms, right? I.e., upshift before it gets TOO far beyond that?
BailOutThread starterReno, Nevada, USA · Mar 5, 2010#141 Originally Posted by
pawsplus ↑ Alrighty! Thanks!
Oh, and I'm assuming that my goal is to stay around 2000 rpms, right? I.e., upshift before it gets TOO far beyond that?
High RPMs don't hurt much when you're in DFCO. I routinely go a little above 4k RPM while in DFCO in the mountains.
LorenSafety Harbor, FL · Mar 5, 2010#142 Originally Posted by
pawsplus ↑ Alrighty! Thanks!
Oh, and I'm assuming that my goal is to stay around 2000 rpms, right? I.e., upshift before it gets TOO far beyond that?
If you're upshifting, you're not in DFCO at all because you're accelerating. That's a topic for another thread. 😉
If you're decelerating/coasting in DFCO, simply don't bother to downshift unless your revs get below 1500.
My typical DFCO maneuver is to just stay in 5th to about 2k or so (I don't really look at the tach), and then skip 4th and downshift to 3rd for the majority of a decel. If I can stretch it further (the light ahead of me is red, or traffic isn't moving), I might grab 2nd and try to maintain enough momentum to stay in 2nd and never have to stop or downshift to 1st if I can avoid it.
The short version of that is: Always coast for as long as possible in DFCO, and always try to time your position within traffic to maintain as much momentum as you can and avoid slowing/stopping unnecessarily.
sbergman27Oklahoma City, OK · Mar 8, 2010#143DFCO is not some exotic new feature. It's been a standard feature of most FI systems for at least 20 years. Many of the electronic feedback carbs of the 80s had it. What *has* changed is that its implementation has gotten more aggressive over the years. On my carbureted 1988 Chevy Sprint Metro, it doesn't kick in unless the engine is above 2500 rpm (about 56 mph in 5th) whereas, apparently, 1100 rpm is sufficient on the Yaris.
Also, it is not some magic feature that you can "use" to get better fuel economy. It does one simple thing: When conditions require *less* power than that produced by the 0.2 gal/hour that the Yaris engine consumes at idle, it eliminates that tiny bit of consumption. If that power is needed, e.g. to keep the engine idling, or even to maintain your desired speed when descending a hill, then the fuel is duly provided, and should not be considered to be any sort of waste.
talnlnkySpokane, Wa · Mar 9, 2010#144seemed pretty magic to me, i instantly saw a 10% (4mpg) increase in mpg's after I started using it.
sbergman27Oklahoma City, OK · Mar 9, 2010#145 seemed pretty magic to me, i instantly saw a 10% (4mpg) increase in mpg's after I started using it.
You mean... after you started consciously aiming toward decelerating over a longer distance and using the brakes less?
Reality check: Consider that if you manage to stay in DFCO mode for a full hour, you've only saved about 0.2 gallons of fuel (specifically due to DFCO) since the Yaris' engine uses about 0.2 gal/hr at idle. To get a 10% improvement in fuel economy over the course of a tank of gas, you would have to spend over 5.5 extra *hours* in DFCO mode. Do you think that you are managing that much?
-Steve Bergman
BailOutThread starterReno, Nevada, USA · Mar 9, 2010#146 Originally Posted by
sbergman27 ↑ You mean... after you started consciously aiming toward decelerating over a longer distance and using the brakes less?
Reality check: Consider that if you manage to stay in DFCO mode for a full hour, you've only saved about 0.2 gallons of fuel (specifically due to DFCO) since the Yaris' engine uses about 0.2 gal/hr at idle. To get a 10% improvement in fuel economy over the course of a tank of gas, you would have to spend over 5.5 *hours* in DFCO mode. Do you think that you are managing that much?
-Steve Bergman
You have quite the attitude about all of this, Steve. DFCO may have existed for a while but it is/was far from common knowledge. Just because you knew about it earlier doesn't turn the rest of us into bumbling idiots, or negate the uniqueness of me discovering and proving it on my own.
While what you say may be technically accurate you completely overlook the fact that fuel efficiency techniques bleed into and overlap each other. It is nigh impossible to extricate an intertwined technique from its siblings, so striving towards DFCO usage will invariably lead to more efficient usage of brakes and deceleration and downhill throttle control while simultaneously making the driver more FE-aware in general. If it is easier for folks to understand that whole set of skills simply as DFCO usage please let them be.
Please try to look beyond the trees so that you can see the forest. Getting caught up in the minutiae of an easy-to-understand and easy-to-use technique will do no one any good.
LorenSafety Harbor, FL · Mar 9, 2010#147Valid point, Steve. We're probably seeing most of our gains in MPG simply from changing our driving habits. DFCO is a good excuse to do it, but we wouldn't be using THAT much more fuel if the engine were idling at all times.
Let's say I was driving conservatively and went 400 miles on 10 gallons of gas. (a reasonable assumption for me, I usually do much better than that in city driving) My average speed for this tank of city driving is 30 mph, so total driving time is 13.3 hours.
Let's say that instead of clutching in and letting the engine idle, I spend 20% of my driving time coasting in DFCO. How much of a difference is it making? 13.3 hours x 20% = 2.66 hours at .2 gph... call it .5 gallons.
400 miles / 10 gallons = 40 mpg
400 miles / 9.5 gallons = 42.1 mpg
Wait... 42.1/40 = 5.2% improvement!
So, yeah... the bulk of our improvements (easily 10-20% over EPA without trying hard) come from driving style changes. But, I'd say that there's a solid 3-5% or more to be gained from making good use of the DFCO feature in city driving. And for people who practice the "pulse and glide" technique, DFCO can improve their highway mpg, too.
No, it's not magic. No, it's not "new" technology. But, now that people know about it, they have developed repeatable driving techniques to take advantage of it.
Footnote: Is it possible to spend 2.6 hours of a tank of gas in DFCO? I think so. Using myself again: My typical trip is maybe 20 miles round trip. If I don't hit at least 20 stops on that trip, I'm stunned. So, for each of those stops, I'm doing a full 20 seconds or so of DFCO coasting. Call it 7 minutes for every 20 miles. 20 of those trips on a 400 mile tank gives us 2:20 just from traffic lights. That's not including the amount of pulse & glide that I do. I'd say for any given mile that I spend cruising at speed, I'm DFCO coasting at least 10 seconds. (if my cruising speed is 45, that's 10 seconds out of every minute and a half, not at all unreasonable) This might only apply to half the miles traveled (the rest of the miles are spent accelerating or decelerating due to stops), so there's 200 miles x 10 seconds each for another 30 minutes of DFCO. I think my estimates here are very conservative for when I'm seriously "hypermiling", and they've added up to 2:50 of DFCO time.
While I completely get what you're saying, Steve... you can't deny that DFCO absolutely CAN make a difference in fuel economy for the driver to takes complete advantage of it.
And it all goes hand in hand. If you're maximizing your DFCO time, you ARE driving conservatively.
LorenSafety Harbor, FL · Mar 9, 2010#148Brian and I were typing at the same time... and said much the same thing in the end. Brian went on to say a few things that I was thinking, but didn't say because my post was too damned long already. Heh.
sbergman27Oklahoma City, OK · Mar 9, 2010#149 Originally Posted by
BailOut ↑ You have quite the attitude about all of this, Steve.
I believe in accuracy, and in correcting misleading and/or erroneous information. What you discovered is that brakes turn kinetic energy into waste heat and that conserving kinetic energy helps fuel economy. DFCO is a relatively minor enhancement to that.
My clarifications in no way reduce the value of the information you have provided. But having a more accurate grounding in *why* it works will allow people to make more effective use of it.
That's not "attitude". It's a simple respect for truth. I believe in calling a spade a spade.
-Steve
sbergman27Oklahoma City, OK · Mar 10, 2010#150 Originally Posted by
Loren ↑ Footnote: Is it possible to spend 2.6 hours of a tank of gas in DFCO?
Actually, that's not the right question. You must spend that amount of *extra* time, over and above what would have been the case had you never even heard of DFCO, in order for the changed driving technique to result in that much improved fuel economy. And modern DFCO is designed so that people *don't* need to know about it to benefit from it. (I think the RPM cutoff on the Yaris is 1100 rpm?)
As mentioned in my previous post, this is about people having an accurate understanding of what is going on. And appealing to the fact that efficient driving practice involves a lot of interacting factors is really irrelevant to that point. Because the benefit specifically attributed to conscious use of DFCO *can* be separated out, and is relatively small in the grand scheme of things.
That doesn't make DFCO bad or insignificant. It just defines its place in the landscape better.
-Steve