I want a free T-shirt
Going Boosted!!!!!!! :D
165 posts · 63,178 views · page 3 of 4
Replies continued
hey guys
i dont even wana explain the issue i have been having well i havent had my car for 4 weeks but getting this week this means i havent had it for 5 weeks now! stupid fuel issue!
well on the bright side walbro i getting done i have an afr gauge that will go in and also got an intercooler water jet spray kit .. I promise to post take a loads of photos as soon as possible! also with new pump since old one was gone hoping for better dyno run! :D all to be posted in the next few 3-4 days i hope!! :D
i dont even wana explain the issue i have been having well i havent had my car for 4 weeks but getting this week this means i havent had it for 5 weeks now! stupid fuel issue!
well on the bright side walbro i getting done i have an afr gauge that will go in and also got an intercooler water jet spray kit .. I promise to post take a loads of photos as soon as possible! also with new pump since old one was gone hoping for better dyno run! :D all to be posted in the next few 3-4 days i hope!! :D
so i get a call from the my tuner my fuel system is installed but now my crank angel sensor is showing a check engine light which is preventing the car from starting! a new sensor has to be ordered another 5 days wait to get it shipped and installed :(
Hmm that don't seem right...
Yea.. I dont believe the sensor is actually bad. but somewhere else. Sounds like he is just throwing parts at it
I've had that wire go bad because it was rubbing and have to replace the sensor before.
But make sure he SHOWS you the bad part. I always do. 🙂
But make sure he SHOWS you the bad part. I always do. 🙂
BTW.. he had that same code on in post #55. Could be harness connection?
Yes I did have a engine code show up ages ago and never went away it was the crank signal well Monday or Tuesday I will be down there to check out my car
I seem to recall this situation with the FIC when our tuner tuned Scions a lot. if I remember correctly, it was one of two things..... The firmware used is not correct, or the FIC unit itself is faulty. I HIGHlY doubt the crank sensor took a crap.
Originally Posted by Blown_xa ↑I seem to recall this situation with the FIC when our tuner tuned Scions a lot. if I remember correctly, it was one of two things..... The firmware used is not correct, or the FIC unit itself is faulty. I HIGHlY doubt the crank sensor took a crap.
So wat ur saying is the my aem fic is fuked and there is nothing wrong with my crank sensor .. Probably have to send it from where I got it to maybe get it check out I got it as a present friends all put money together and brought it for me
^No. What he is suggesting is that it might need a firmware update to a different version, maybe even a previous version. I would certainly try that before deciding the unit itself is toast.
.z107 is the accepted firmware for toyotas / scions.
^^^^This
alright thanks alot guys i will double check that with the guys !!!
okay guys getting my car tomorrow morning.. but not happy
speaking to the guy my o2 oxygen sensors the heating element inside both the o2 sensors keep short circuiting which means when my car is cold it will run crap cause it wont be getting information! They brought me two new ones and after they dyno'd it both sensors heating element have short circuited again! thats my first fuking problem
secondly my car will get up 5000rpm and will hit a dead wall! according to the guy he says it a conflict between aem fic and the ecu, could the problem be that the car timing is off at high rpm possibly? Which isnt properly done in the ignition section of the aem?
why is it that my yaris has major issues while other yaris members arent seeming to have as bad of issues as i am! i have a feeling that the boomslang i have maybe isnt the same wiring as the yaris in america!
he said that the afr on WOT is 12:1 which i still need to install my AFR gauage in
anyone give me any input i have no idea wat the fuk is going on!? i dont understand the point of having a boosted yaris if u can even have the full rev range
speaking to the guy my o2 oxygen sensors the heating element inside both the o2 sensors keep short circuiting which means when my car is cold it will run crap cause it wont be getting information! They brought me two new ones and after they dyno'd it both sensors heating element have short circuited again! thats my first fuking problem
secondly my car will get up 5000rpm and will hit a dead wall! according to the guy he says it a conflict between aem fic and the ecu, could the problem be that the car timing is off at high rpm possibly? Which isnt properly done in the ignition section of the aem?
why is it that my yaris has major issues while other yaris members arent seeming to have as bad of issues as i am! i have a feeling that the boomslang i have maybe isnt the same wiring as the yaris in america!
he said that the afr on WOT is 12:1 which i still need to install my AFR gauage in
anyone give me any input i have no idea wat the fuk is going on!? i dont understand the point of having a boosted yaris if u can even have the full rev range
if that is the excpeted fireware i am using currently the F/IC - 6 Patch V3.05Originally Posted by Focus_Sh1ft ↑.z107 is the accepted firmware for toyotas / scions.
where do u find the z.107???
Check the aem forums they have it on there. Don't kno why you are having some many issues. It must be in the tuning somewhere I think. Most of us are running open loop with no o2 sensor.Originally Posted by djgab101 ↑if that is the excpeted fireware i am using currently the F/IC - 6 Patch V3.05
where do u find the z.107???
why is it that my yaris has major issues while other yaris members arent seeming to have as bad of issues as i am!Maybe you should ask your tuner that.
They brought me two new ones and after they dyno'd it both sensors heating element have short circuited again!Did they give you the old parts to inspect?
RULE #1: Always get back any parts replaced on your car.
going tomorrow i will ask him!Originally Posted by cali yaris ↑Maybe you should ask your tuner that.
my tuner has no idea!! he says its conflict between aem and ecu
Did they give you the old parts to inspect?
RULE #1: Always get back any parts replaced on your car.
well tuning is going shit so i probably say tunning is the issue!Originally Posted by Yoda ↑Check the aem forums they have it on there. Don't kno why you are having some many issues. It must be in the tuning somewhere I think. Most of us are running open loop with no o2 sensor.
If you can take your car somewhere else to have them have a look.Originally Posted by djgab101 ↑well tuning is going shit so i probably say tunning is the issue!
Alright got my car back runs well Only problem is a constant cranksensor mulfaction and both exhaust sensor heat circuit
The 2 oxygen sensors both the heat element inside have broken which where brand new so the car has to warm up the o2 sensor
The car still hits a brick wall at 5000rpm but reading aem forums they have see this before I am going to try tonight and fix that problem that's to you guys and aem i think it's the firmware which I hope should fix it more to update!
Btw garm I asked for parts and he apparently couldn't find them which is bullshit! He probably has them in the garage!
The 2 oxygen sensors both the heat element inside have broken which where brand new so the car has to warm up the o2 sensor
The car still hits a brick wall at 5000rpm but reading aem forums they have see this before I am going to try tonight and fix that problem that's to you guys and aem i think it's the firmware which I hope should fix it more to update!
Btw garm I asked for parts and he apparently couldn't find them which is bullshit! He probably has them in the garage!
I am looking around for places not many places wana deal with small cars or have no expirence with the aem ficOriginally Posted by Yoda ↑If you can take your car somewhere else to have them have a look.
I think hitting the brick wall a 5000rpm is probably the MAF voltage not being clamped. Feels like an early rev limiter yes? Did somebody wire in the FIC, or did you get the plug and play harness?Originally Posted by djgab101 ↑Alright got my car back runs well Only problem is a constant cranksensor mulfaction and both exhaust sensor heat circuit
The 2 oxygen sensors both the heat element inside have broken which where brand new so the car has to warm up the o2 sensor
The car still hits a brick wall at 5000rpm but reading aem forums they have see this before I am going to try tonight and fix that problem that's to you guys and aem i think it's the firmware which I hope should fix it more to update!
Btw garm I asked for parts and he apparently couldn't find them which is bullshit! He probably has them in the garage!
Originally Posted by Blown_xa ↑I think hitting the brick wall a 5000rpm is probably the MAF voltage not being clamped. Feels like an early rev limiter yes? Did somebody wire in the FIC, or did you get the plug and play harness?
the maf hasnt been clamped which i was trying to solve how to do it and still unsure??? the aem is using the plug and play harness!
well tuning is going shit so i probably say tunning is the issue!1. No. The tuner is the issue.
Btw garm I asked for parts and he apparently couldn't find them2. See #1.
if he doesn't have the parts he took out he probably never actually took anything out...
That's the version of the software you're running on your computer, not the firmware running on the FIC itself.Originally Posted by djgab101 ↑if that is the excpeted fireware i am using currently the F/IC - 6 Patch V3.05
where do u find the z.107???
Your tuner is a moron.Originally Posted by djgab101 ↑well tuning is going shit so i probably say tunning is the issue!
I believe every person that has used the boomslang has had issues with a crank related CEL
sounds like with the o2 sensor that they guys need something to blame because they do not wish to be at fault. Also try and taking a look to see if it looks as though the o2 sensors where even removed or if they just guessed that to be the issue and are just trying con some more money out of you.
alright guys updated the firmware and car is still running which is good i noticed that the guy put the o2 sensor in the wrong bung ... he put the o2 sensor in the bung where the wideband should be! i purchased a prosport wideband and was looking and noticed it! not sure if that would change the issue! installing my wideband in the next week i hope when i do i will put the o2 sensor in the correct bung!
car runs smoothly uptill 5000rpm sometimes it will go all the way to redline sometimes it wont
Next step is to clamp my maf sensor cause at the moment my maf sensor hasnt been touched at all.. in the aem maf map its all "0" i want to hide the boost i am looking all over internet youtube and aem forums to get an idea of wat to do i will attempt it asap!
and guys thanks alot for all ur help!!! not sure how much u guys understand how much i appreciate all the feedback!!
car runs smoothly uptill 5000rpm sometimes it will go all the way to redline sometimes it wont
Next step is to clamp my maf sensor cause at the moment my maf sensor hasnt been touched at all.. in the aem maf map its all "0" i want to hide the boost i am looking all over internet youtube and aem forums to get an idea of wat to do i will attempt it asap!
and guys thanks alot for all ur help!!! not sure how much u guys understand how much i appreciate all the feedback!!
I believe every person that has used the boomslang has had issues with a crank related CELgood to know i am not the only one!
after researching found that CT Scott found a problem with the PnP harness!
this is not easy to understand but looks like i probably have to do this to get the crank engine light fixed
my plan is to check the PnP with the installation guide and look over everything! espically crank and cam wires
also going to check my oxygen sensors wires maybe a error there since it is apparently shorting out my sensor heater!
"The issue that I found with it last night is that the MAF (VG) signal and the Crank position sensor (NE-) signal are supposed to be "intercepts" rather than "taps" as they are wired on the boomslang. As-is. the F/IC can only read, and not override the MAF and Crank signals to the ECM. ""
this is not easy to understand but looks like i probably have to do this to get the crank engine light fixed
my plan is to check the PnP with the installation guide and look over everything! espically crank and cam wires
also going to check my oxygen sensors wires maybe a error there since it is apparently shorting out my sensor heater!
good catch.. who needs a tuner when you have yarisworld/forced induction forums..
Dam straight!!!!!!!!!!Originally Posted by ilikerice ↑good catch.. who needs a tuner when you have yarisworld/forced induction forums..
Never hurts to double check wiring and connections but keep in mind that the harness that Scott found the issue with was a very early pre-production harness that Boomslang made.
The harness you have is revised, with a single large connector and we have not had any wiring issues with these.
The harness you have is revised, with a single large connector and we have not had any wiring issues with these.
That good to know hopefully it will be a quick look over the wires and can go from there!Originally Posted by Jeff@MicroImage ↑Never hurts to double check wiring and connections but keep in mind that the harness that Scott found the issue with was a very early pre-production harness that Boomslang made.
The harness you have is revised, with a single large connector and we have not had any wiring issues with these.
double check wires and all looks fine all good connections!!
installed afr gauge working well.. since i updated my firware settings have changed and once i start clamping my maf the ecu will change its fuel afr so i am gonna have to start with a new tune i was going to start with.. after changing maf map to percentage and all zeros i had receieved a check engine light p0223 "throttle sensor curcit high" car idles alright but wont rev at all!! i am pretty sure this is the cause of maf sensor!
Clampin my MAF sensor not sure to use percentage or voltage as the option of tuning
then i was going to adjust the AFR using the Fuel map with input as MAF once the car has this set up it should hopefully run smooth thru out the rev range with ECU not seeing boost! 12.1 on wot 13.1 on cruise and 14.7 on idle!
from there might try and adjust the ignition map can anyone give me any tips that might make this a litttle easier???? at the moment gathering as much information from yarisworld aem fic forums and youtube aem fic deminstrations! also got the AEMlog which has help alot
installed afr gauge working well.. since i updated my firware settings have changed and once i start clamping my maf the ecu will change its fuel afr so i am gonna have to start with a new tune i was going to start with.. after changing maf map to percentage and all zeros i had receieved a check engine light p0223 "throttle sensor curcit high" car idles alright but wont rev at all!! i am pretty sure this is the cause of maf sensor!
Clampin my MAF sensor not sure to use percentage or voltage as the option of tuning
then i was going to adjust the AFR using the Fuel map with input as MAF once the car has this set up it should hopefully run smooth thru out the rev range with ECU not seeing boost! 12.1 on wot 13.1 on cruise and 14.7 on idle!
from there might try and adjust the ignition map can anyone give me any tips that might make this a litttle easier???? at the moment gathering as much information from yarisworld aem fic forums and youtube aem fic deminstrations! also got the AEMlog which has help alot
any advice would be apprepicated! :D
After doing loads of experiments and testing found out that the knocking has come from my 4th cylinder it is a bottom end problem the compression in the cylinder was test at 12psi added oil into the cylinder and it went to 150 psi so i am pretty sure my piston rings are fuked and my piston is rattling when it goes up and down the cylinder bore :(
That sucks. Sorry to hear that man. I had the same problem with not reving to redline. I had to retard my timing progessively as boost increased in my timing map to take care of it. Stock compression is pretty high and with boost if the nock sensor detects detonation it will retard timing and and not allow the engine to get to redline.Originally Posted by djgab101 ↑After doing loads of experiments and testing found out that the knocking has come from my 4th cylinder it is a bottom end problem the compression in the cylinder was test at 12psi added oil into the cylinder and it went to 150 psi so i am pretty sure my piston rings are fuked and my piston is rattling when it goes up and down the cylinder bore :(
Unfortunatly it seems you may have bigger problems. Try a rebuild with new pistons and rods. You wont regret it.
well it is offical my engine blew up, on the way from going to a garage my motor made a massive bang oil squirted from somewhere onto my turbo making my car into a massive ball of white smoke!! all my engine oil went all over the road, checking as much as i could didnt see any crack in the engine but i couldnt see the back side of the engine where the exhaust/turbo is, tow truck took the car now at the Garage probably get a phone call tomorrow asking telling me issue happened! i am pretty sure my engine is finished so a new engine will be brought soon possibly upgrading with forged pistons and rods
Sorry to hear of the troubles! I hope you can get her back on the road soon and there isn't too much damage besides the motor.
When going for the forged build,please do a nice thread with lots of pictures!
Thanks.
Thanks.
guys so i found a motor with 29 000 kms on it! I want to rebuild the bottom end so forged pistons and rods!
How difficult is this DIY, i have pretty good knowledge on cars! I have the toyota 1nzfe full specs on engine remvoal and overhaul with pictures and instructions on how to do everything but can any one offer advice on ?
How difficult is this DIY, i have pretty good knowledge on cars! I have the toyota 1nzfe full specs on engine remvoal and overhaul with pictures and instructions on how to do everything but can any one offer advice on ?
This recent thread is probably the best one on that subject:Originally Posted by djgab101 ↑guys so i found a motor with 29 000 kms on it! I want to rebuild the bottom end so forged pistons and rods!
How difficult is this DIY, i have pretty good knowledge on cars! I have the toyota 1nzfe full specs on engine remvoal and overhaul with pictures and instructions on how to do everything but can any one offer advice on ?
Limits of stock 1nzfe found once and for all.
pimp and his friend did it themselves. I had my bottom end built by someone else.
i have been watching that thread has some really good pictures and information!Originally Posted by CTScott ↑This recent thread is probably the best one on that subject:
Limits of stock 1nzfe found once and for all.
might see once all the parts how difficult it might be!
Finally got my car from the tow company Sunday I shall start stripping down my car! Find out wat actually happened to my engine!
Would everyone agree that my engine has been damaged from a bad tune? If it's only on 8psi with engine damaged tune seems to be the problem!
Would everyone agree that my engine has been damaged from a bad tune? If it's only on 8psi with engine damaged tune seems to be the problem!
I know this is kinda far fetched.. but If it you had the money, when ever a check engine light comes on, the ecu will take snap shots of (correct me if im wrong) 10 seconds before the CEL came on and after. So you can see what ALL the sensors was reading when your engine blew up. Ex, oil pressure drop, fuel mixtures, knocks/pings.
only reason i say this is pure curiousity.. At lexus, we could see what happend and what RPM, engine temp, etc. the CEL took place and try to duplicate it.
Like I said. It's a long shot and would prob have to pay for a tow truck and pay a diag fee.. They can use thier laptop TechStream tool and print out a copy for you
only reason i say this is pure curiousity.. At lexus, we could see what happend and what RPM, engine temp, etc. the CEL took place and try to duplicate it.
Like I said. It's a long shot and would prob have to pay for a tow truck and pay a diag fee.. They can use thier laptop TechStream tool and print out a copy for you
May need to go to a Toyota dealer to get scanned with the oem scanner to get that freeze frame info.Originally Posted by ilikerice ↑I know this is kinda far fetched.. but If it you had the money, when ever a check engine light comes on, the ecu will take snap shots of (correct me if im wrong) 10 seconds before the CEL came on and after. So you can see what ALL the sensors was reading when your engine blew up. Ex, oil pressure drop, fuel mixtures, knocks/pings.
only reason i say this is pure curiousity.. At lexus, we could see what happend and what RPM, engine temp, etc. the CEL took place and try to duplicate it.
Like I said. It's a long shot and would prob have to pay for a tow truck and pay a diag fee.. They can use thier laptop TechStream tool and print out a copy for you