Yarisworld Archive

Going Boosted!!!!!!! :D

165 posts · 63,178 views · page 2 of 4

Replies continued

djgab101Thread starteraustralia · Jan 11, 2012#51
after researching it made more sense!! found this DIY http://www.dsmtuners.com/forums/arti...tion-pipe.html

made more sense.. i will find time to do this and see if it work hopefully will stop backfiring and improve the cars response
djgab101Thread starteraustralia · Jan 17, 2012#52
Goods news my boomslang harness has arrived from microimage thanks garm!! Bad news was messing around with the o2sensor trying to get the signal wire for my afr gauge and for some reason p0032 and p0038 cels have cone up and won't go away when I clear it 2seconds later code came back! I want to get this fixed I don't like it when my check engine light is on!!
cali yarisCanoga Park, CA · Jan 17, 2012#53
^ you can't split the wire from your O2 sensor for a gauge. You need separate, dedicated bungs and use two sensors. That's why wideband AFR gauges come with a sensor (they all should, anyway)
djgab101Thread starteraustralia · Jan 18, 2012#54
Thanks for that garm I either blew a fuse or the wire cause it won't go away! But tomorrow I will sort it out!
djgab101Thread starteraustralia · Jan 31, 2012#55
Big car issues at the moment!!! I have 2 codes coming P0102 Mass or Volume Air Flow Circuit Low Input and P0335 Crankshaft Position Sensor A Circuit Malfunction

The car is running like shit idle is alright when I rev the engine it barely wants to rev and backfires badly ... Car will barely move !!!

Is this because of my turbo is fucked not getting enough air from the turbo seems it's not sucking in any air! Any one for some help?
Blown_xaVirginia · Jan 31, 2012#56
👎
Originally Posted by djgab101 ↑
Big car issues at the moment!!! I have 2 codes coming P0102 Mass or Volume Air Flow Circuit Low Input and P0335 Crankshaft Position Sensor A Circuit Malfunction

The car is running like shit idle is alright when I rev the engine it barely wants to rev and backfires badly ... Car will barely move !!!

Is this because of my turbo is fucked not getting enough air from the turbo seems it's not sucking in any air! Any one for some help?
Sounds like the FIC. Who tuned it? Plug in factory ecu to see if it idles fine. Or usually the FIC comes with a harness bypass plug... Unplug the FIC and plug in bypass harness. Also check to make sure all couplers are secure.
YodaFL · Feb 1, 2012#57
Do you have a boost gauge or A/F? Might be a vac leak but most likely the something with the FIC since you have the P0335. As Blown said use the supplied bypass harness n see if that fixes it then you kno its the FIC.
cali yarisCanoga Park, CA · Feb 1, 2012#58
this:
usually the FIC comes with a harness bypass plug... Unplug the FIC and plug in bypass harness.
djgab101Thread starteraustralia · Feb 1, 2012#59
Alright guys moment of true unplug AEM fic with the boomslang I didn't use he by pass my car is going to be tuned next week so hopefully car can make it there and then they can plug in the harness and bypass and tune it!

After unplug AEM fix car works fine again .. Tuner said dont waste money getting Air/fuel but I am gonna get one make sure!!

The bypass harness didn't know it was need .. Where does it even connect to and wat does it control I feel like sub a noob!
djgab101Thread starteraustralia · Feb 1, 2012#60
alright here is my problem! when i disconnect the boomslang harness from the ecu the car runs fine! if i plug the boomslang into the ecu and put the bypass harness the car runs like shit .. rough reving and jumping idle problems!! so is there an issue with my boomslang harness or wat? then when i plug it into the aem fic .. it seems to run fine with only once their was power loss for a split second!! i dont think the boomslang works with the aem fic bypass it doesnt seem to work!
CTScottUSA, CT · Feb 1, 2012#61
Originally Posted by djgab101 ↑
alright here is my problem! when i disconnect the boomslang harness from the ecu the car runs fine! if i plug the boomslang into the ecu and put the bypass harness the car runs like shit .. rough reving and jumping idle problems!! so is there an issue with my boomslang harness or wat? then when i plug it into the aem fic .. it seems to run fine with only once their was power loss for a split second!! i dont think the boomslang works with the aem fic bypass it doesnt seem to work!

The boomslang should work fine with the bypass. With fnkngrv's boomslang I found that two wires on the male connector had broken loose from the pins. The male end uses a connector that is harvested from an ECM, so rather than having pins which are crimped to the wires, the wires are just soldered to the tabs that would go into the printed circuit board in the ECM. If any of the solder joints aren't perfect, they will pull off with vibration.
djgab101Thread starteraustralia · Feb 2, 2012#62
Check my connections everything seems fine!

After driving around everything fine that one spot where I have loss of power is at low revs when I full throttle it the car has loss of power and makes noise from exhaust as if valves are opening and closing and u can hear it thru the exhaust! Taking my car in 5 days time to fix o2 sensor and the dyno tune! Numbers and dyno sheet hopefully will be provided :)
cali yarisCanoga Park, CA · Feb 2, 2012#63
^ sounds like pinging. What grade gas/fuel/petrol (whatever they call it down under) are you using?
djgab101Thread starteraustralia · Feb 2, 2012#64
Lol I am using 98 octane premium Petrol
cali yarisCanoga Park, CA · Feb 3, 2012#66
What are you using to monitor A/F ratios? Hopefully not the scangauge, it's far too slow to be helpful with that parameter.
djgab101Thread starteraustralia · Feb 3, 2012#67
At the moment waiting on wide band to arrive so no monitor any a/f ratios I hope when This goes for a tune on Tuesday that all goes well and everythig is fixed!
djgab101Thread starteraustralia · Feb 8, 2012#68
Okay car went for a tune i am picking it up tomorrow in the morning!

apparently At 5000rpm when the mixutre is lean the car pushes to redline but apparently when they add more fuel to keep it stoich the car cuts out. he doesnt wana lean the mixture cause it damage the engine. he said maybe a walbro fuel pump or injectors would solve the issue i am going to order 1zz injectors and hope it fixes the issue!

Otherwise the car is running extremely well apparently and they are happy with wat tune
once i get my car tomorrow i will be able to see how it runs and go from there..
cali yarisCanoga Park, CA · Feb 8, 2012#69
What is the duty cycle of the injectors looking like?
They should be able to tell 100% if that's the problem. No guessing allowed.
Pur_BluEast Bay, Castro Valley · Feb 8, 2012#70
U tell um Garm... did they at least tell u what numbers they were able to make with the tune or will u find out 2morrow?
djgab101Thread starteraustralia · Feb 8, 2012#71
man i dont know anymore!
getting my car back they told me that my max hp was 129HP if that is true which i dont know is like 20 hp gain on a turbo which i believe cant be right to top it off the dyno was done in 4th gear which i think to be sure should be donw in 3rd gear?

once i got home i looked at the tune the guy did and looking thru the maps he only adjusted the ignition map and fuel map

the o2 map havent been changed or messed around with at all as soon as my a/f gauage arrives i am going to install it and see how the AFR look! car runs up until 5000 rpm where seems to lose of power from fuel

and garm i asked him wat my duty cycle was and he just gave me an example about how at idle they may use .8 volts and at full throttle they could be using 3 volts and injectors arent the way to go it is better to ungrade fuel pump so that when the injectors are opened it would squirt more fuel into the engine when the injectors are open

1 attachment not included in this copy

djgab101Thread starteraustralia · Feb 8, 2012#72
Originally Posted by Pur_Blu ↑
U tell um Garm... did they at least tell u what numbers they were able to make with the tune or will u find out 2morrow?
hey i know i was suspost to put photos trying to sort my tune out first but photos will come up!
cali yarisCanoga Park, CA · Feb 9, 2012#73
looking thru the maps he only adjusted the ignition map and fuel map
That's perfectly fine, fuel and timing are pretty much what you tune with, unless you get fancy.

garm i asked him wat my duty cycle was and he just gave me an example about how at idle they may use .8 volts and at full throttle they could be using 3 volts
So, using your example, you have a range of 2.2v. 3-.22 = 2.78v = 90%. IF it's linear. I know there's a way to figure or measure it. NOT quoting real numbers.

So sorry, but that is BS -- I've never paid someone to tune my car and not been told what my duty cycles were. Should be between 0-100%, with 100% maxed out. (I think I've seen 110% before, come to think of it). How in the world would you know when to upgrade your injectors without this information?

{edit} maybe this is the limitation of a piggyback (I run standalone) -- can someone else chime in here?

the dyno was done in 4th gear
That is the correct gear in our cars. My pulls were done in 4th at all four of my sessions (180, 230, 310, 357, and one more to come 😉 ).

my max hp was 129HP
Something wrong there unless you are running 2psi.

Post the chart with power AND torque. The two lines should cross at 5250.
Post the chart with air/fuel vs. rpm.


Then we'll know something.
cali yarisCanoga Park, CA · Feb 9, 2012#74
Does the tuner have an email address? 😁
djgab101Thread starteraustralia · Feb 9, 2012#75
Garm ur 100 percent right the tuners here seem to care more about high horse power cars than they do about smaller cars!
Apparently according to a friend 129 hp is the power at the wheels! The car is boosting all the way to 8 even sometimes 8.5 psi! Car is pushing strong no signs or knocking but Australia's weather is really hot and humid with air intake temperatures at 40degrees and higher on hot days not very good for turbos ... When the weather cools down performance shows strong!

Other zage turbod yaris is ur hp at the wheel or fly wheel? I am going to call up tomorrow and ask them about my dyno sheet cause it feels like i have results but dyno sheet says otherwise
YodaFL · Feb 9, 2012#76
It's all at the wheel
cali yarisCanoga Park, CA · Feb 9, 2012#77
stock Yaris is approx. 106 bhp, and 90-95 whp.

Looking forward to seeing the other, more complete dyno charts.
Sorry for your tuning troubles, it's not uncommon.

Australia's weather is really hot and humid with air intake temperatures at 40degrees and higher on hot days not very good for turbos ...
Yes and no. Higher temps, yes. Although I've raced in 100 degree heat and the car felt pretty strong. It's all about intake temps (see below).

Even at those temps (humidity will raise your power not lower it, turbo motors love a little water) -- you should be making 150+ whp at 8 psi, at the very minimum.

Now ask them what your intake temperatures were on the pulls. 😉 Another critical piece of information any tuner would know.

Sorry, I'm trying to do this piece by piece.
These are all questions you should ask in the meeting with the tuner before you drop off your car. IMO.
Something like the following.

It may sound tedious and anal, but this will save you guys 99% of what I call "Tuning Grief".

Pre-Dyno questions:

Do you charge by the job or by the hour for tuning?
Which tuner from your staff will be running my session?
What data do you monitor, and will be able to report to me during and after the session?
Do you do partial pulls at constant rpm for drivability tuning?
How many cars like mine have you tuned before?
How many times have you tuned with the management I have?
What is your policy if something needs tweaking, repair or replacement during the session?
What do you consider too lean/too rich for my tune?
I have an idea what my car should make when you tune it. What happens if we don't meet that goal?
When was your dyno last calibrated?
May I see some before/after dyno charts from previous tunes?
May I contact 2 or 3 of your customers to get reviews?
May I observe another customer's session first?

And so on... until you feel comfortable you are going to get what you are paying for.
ilikericesavannah, ga · Feb 9, 2012#78
That is brilliant! This post alone should be a sticky in this section.

"Pre-dyno Q's for your tuner"

good stuff garm.. will have to favorite this one
Blown_xaVirginia · Feb 9, 2012#79
I'm guessing because he is in Australia, the tune was done on a dyno dynamics dyno ( which is Australian ). So 129whp seems right on the $ for 8 psi on a small turbo. As far as duty cycles go from a piggy backs standpoint, it is a estimate at best, and is not accurate. When we tune a car with a piggyback, we know it is out of fuel by what the dyno is saying. 129 whp is the point when stock injectors are maxed out on the 1nzfe, tC injectors max out at 150whp... ( stock fuel pump) I found that out personally.
CTScottUSA, CT · Feb 9, 2012#80
There's actually an OBD PID for reading the injector pulse width, which returns a value between 0 and 32.64 ms. The duty cycle is a function of the pulse width and the engine RPM.

IDC = (RPM x IPW) / 1200

So, if the injector pulse width is 20 ms @ 5000 RPM, then the injector duty cycle = (5000 x 20) / 1200 = 83.3%
Blown_xaVirginia · Feb 9, 2012#81
Originally Posted by djgab101 ↑
man i dont know anymore!
getting my car back they told me that my max hp was 129HP if that is true which i dont know is like 20 hp gain on a turbo which i believe cant be right to top it off the dyno was done in 4th gear which i think to be sure should be donw in 3rd gear?

once i got home i looked at the tune the guy did and looking thru the maps he only adjusted the ignition map and fuel map

the o2 map havent been changed or messed around with at all as soon as my a/f gauage arrives i am going to install it and see how the AFR look! car runs up until 5000 rpm where seems to lose of power from fuel
and garm i asked him wat my duty cycle was and he just gave me an example about how at idle they may use .8 volts and at full throttle they could be using
3 volts and injectors arent the way to go it is better to ungrade fuel pump so
that when the injectors are opened it would squirt more fuel into the engine when the injectors are open
Ok I didn't see this before. So it was a dyno dynamics, as I suspected.
Also, from the dyno graph.... Full boost is 6.5 psi, not 8. Those hp numbers are good, don't let anyone tell you otherwise. 150whp on that dyno bends rods. The voltage description you described is most likely the MAF voltage table, which is not related to duty cycle. Only thing I don't like seeing on that dyno sheet.... Is the fact they never calibrated road speed to
RPM, so I don't know how the tuner knew where to make fueling corrections accurately. That sheet also is labeled as " run file 009" , we have never been able to tune a car in just 9 pulls.... So that is suspect. Unless they purposely stopped tuning because they were not comfortable with the fueling.
cali yarisCanoga Park, CA · Feb 10, 2012#82
Good points. Zage kit wastegate spring is supposed to be 7 psi, so 6.5 seems reasonable.

But if people here are getting 150-170 whp out of the same kit on the same car with the same management, how does that dyno read as low as 129? I understand some differences but that is 20% minimum. Is it really that brutal of a dyno machine?

I've only tuned on a couple of dynos -- so I'm not qualified to say for certain. Blown_xa, you probably know better.
ilikericesavannah, ga · Feb 10, 2012#83
ok, My first dyno graph about 1 1/2 years ago I posted was on a dyno dynamics.. IF anyone remembers, on 3 pulls, It showed I got 115 whp on a stock yaris. I came to find out that this particular dyno, someone can manipulate the numbers. Never understood why. Went to another shop who had a different dyno, the one scca only accepts and I had 86 whp stock.

BUT, also been talking to some guys who tune and they say the dyno numbers are only a reference. just use a dyno and tune it using only that dyno.

Just throwing my personal experience in there. Dont know the entire background of the OP setup. just something to consider. If I am wrong then correction is needed, please input
pimp my yarischicago · Feb 10, 2012#84
183whp and 187tq on a mustang dyno at about 70F and 9.5 psi
Blown_xaVirginia · Feb 10, 2012#85
Yea, any dyno can have a correction factor entered. Usually if there is a correction factor, it will be on the sheet most of the time ( example : correction 1.12 or SAE.... If it just says SAE, that could be anything. 1.12 for example is 12%. We leave it at zero, unless the customer requests Dyno Jet numbers ( some cars get classified through NASA by dyno jet numbers). Dyno dynamics uncorrected reads 8 to 12% lower than dyno jet, and 15 to 18% lower than dyna pack. 84 to 86 whp is what I saw on stock xA xB a long time ago during a scion meet.

But yea, the dyno is just a tool for tuning... Don't get all caught up with numbers. But to shed some light, that dyno is on the $ from what I see. Plus it is always fun to show up on a dyno day elsewhere and put down crazy numbers.
cali yarisCanoga Park, CA · Feb 10, 2012#86
^ Agreed that it's just a reference, especially if you use the same dyno over and over again.

But I think there's something off with the whole thing. Until I see more charts or know duty cycles and/or intake temps, I can't comment any further. I'm no expert at this, but I know what I know from my extensive trial and error efforts. 🙁
ilikericesavannah, ga · Feb 10, 2012#87
Dyno Jet, thats what it was. could not remember that to save my life
djgab101Thread starteraustralia · Feb 11, 2012#88
Man thanks guys for the feedback thanks alot guys!!!!!!!!!!!!!!!!!!!!!!!!! 👏

Originally Posted by cali yaris ↑
stock Yaris is approx. 106 bhp, and 90-95 whp.

Looking forward to seeing the other, more complete dyno charts.
Sorry for your tuning troubles, it's not uncommon.



Yes and no. Higher temps, yes. Although I've raced in 100 degree heat and the car felt pretty strong. It's all about intake temps (see below).

Even at those temps (humidity will raise your power not lower it, turbo motors love a little water) -- you should be making 150+ whp at 8 psi, at the very minimum.

Now ask them what your intake temperatures were on the pulls. 😉 Another critical piece of information any tuner would know.

Sorry, I'm trying to do this piece by piece.
These are all questions you should ask in the meeting with the tuner before you drop off your car. IMO.
Something like the following.

It may sound tedious and anal, but this will save you guys 99% of what I call "Tuning Grief".

Pre-Dyno questions:

Do you charge by the job or by the hour for tuning?
Which tuner from your staff will be running my session?
What data do you monitor, and will be able to report to me during and after the session?
Do you do partial pulls at constant rpm for drivability tuning?
How many cars like mine have you tuned before?
How many times have you tuned with the management I have?
What is your policy if something needs tweaking, repair or replacement during the session?
What do you consider too lean/too rich for my tune?
I have an idea what my car should make when you tune it. What happens if we don't meet that goal?
When was your dyno last calibrated?
May I see some before/after dyno charts from previous tunes?
May I contact 2 or 3 of your customers to get reviews?
May I observe another customer's session first?

And so on... until you feel comfortable you are going to get what you are paying for.
garm i hopeing to get some of these important questions answears on monday cause they are closed on the weekend!

Originally Posted by Blown_xa ↑
I'm guessing because he is in Australia, the tune was done on a dyno dynamics dyno ( which is Australian ). So 129whp seems right on the $ for 8 psi on a small turbo. As far as duty cycles go from a piggy backs standpoint, it is a estimate at best, and is not accurate. When we tune a car with a piggyback, we know it is out of fuel by what the dyno is saying. 129 whp is the point when stock injectors are maxed out on the 1nzfe, tC injectors max out at 150whp... ( stock fuel pump) I found that out personally.
good to know when stock injectors max out gives me some information on wat to do!

Originally Posted by CTScott ↑
There's actually an OBD PID for reading the injector pulse width, which returns a value between 0 and 32.64 ms. The duty cycle is a function of the pulse width and the engine RPM.

IDC = (RPM x IPW) / 1200

So, if the injector pulse width is 20 ms @ 5000 RPM, then the injector duty cycle = (5000 x 20) / 1200 = 83.3%
definitaly gonna try have a look into this and see if i can find some codes to get my injector pulse width!!
Originally Posted by cali yaris ↑
Good points. Zage kit wastegate spring is supposed to be 7 psi, so 6.5 seems reasonable.

But if people here are getting 150-170 whp out of the same kit on the same car with the same management, how does that dyno read as low as 129? I understand some differences but that is 20% minimum. Is it really that brutal of a dyno machine?

I've only tuned on a couple of dynos -- so I'm not qualified to say for certain. Blown_xa, you probably know better.
if there spring rate is 7psi but my gauge is showing 8 psi boosting on full throttle at arond 4500rpm .. i was told mine was 8psi set! not many places that do dyno runs in around me i have about 3 places in 1 hours drive from me
djgab101Thread starteraustralia · Feb 11, 2012#89
i Have ordered myself a set of 1zz injectors and also thinking of getting a walbro 255 fuel pump to go with the car! some times at full throttle car seems to be starved of fuel espically at high rpm! does anyone know a diy or where i can locate the fuel pump? is it in the tank or external fuel pump? finding it hard to find information about it!

found my information guys
http://www.scribd.com/doc/8678420/20...08-Fuel-System
cali yarisCanoga Park, CA · Feb 11, 2012#90
255 goes in the tank. Your stock pump is about the size of a "D" cell battery, lol. The 255 is a little bigger, will require minor mods to install in the tank.

That's what I'm using with 632cc injectors, I have more than enough power to go beyond 400 whp.
djgab101Thread starteraustralia · Feb 14, 2012#91
on the way my walbro fuel pump and 1zz injectors!!!!!!!!!!

i had a question i unplug my o2 sensor to run in only open look but sometimes when i was driving it would still change to closed loop is this because of the intake sensor?
Bluevitz-rsOshawa, Ontario, Canada · Feb 14, 2012#92
By O2, you're referring to the second one after the CAT? If so, it's only there to make sure the CAT is working.
cali yarisCanoga Park, CA · Feb 14, 2012#93
on the way my walbro fuel pump and 1zz injectors!!!!!!!!!!
I don't remember getting a chance to take that order, either. 🙄
YodaFL · Feb 14, 2012#94
Originally Posted by cali yaris ↑
I don't remember getting a chance to take that order, either. 🙄
haha you see what he did there 😁
cali yarisCanoga Park, CA · Feb 14, 2012#95
Picture not included in this copy
djgab101Thread starteraustralia · Feb 15, 2012#96
Originally Posted by cali yaris ↑
I don't remember getting a chance to take that order, either. 🙄
Didn't know u sold 1zz injectors or walbro haven't seen it on microimage!
cali yarisCanoga Park, CA · Feb 16, 2012#97
And I keep saying to make inquiries and check our line card. But it's ok you can buy from whatever source works for you!
djgab101Thread starteraustralia · Feb 17, 2012#98
Originally Posted by cali yaris ↑
And I keep saying to make inquiries and check our line card. But it's ok you can buy from whatever source works for you!
yea but garm products are always the best plus free stickers 👍
if i need anything i am going to inbox u first !!
cali yarisCanoga Park, CA · Feb 18, 2012#99
free T shirts if you keep coming back! 👍
cali yarisCanoga Park, CA · Apr 10, 2012#100
sooo.... how's it going? 🙂

on the way my walbro fuel pump and 1zz injectors!!!!!!!!!!

i had a question i unplug my o2 sensor to run in only open look but sometimes when i was driving it would still change to closed loop is this because of the intake sensor?