Yarisworld Archive

Micro Image Short Shift Kit- prototype review

125 posts · 57,866 views · page 2 of 3

Replies continued

cali yarisCanoga Park, CA · Jul 13, 2011#51
No need for a group buy, since they were already produced.

They'll be up in our online store the day they come in (maybe a few days before).

Full kit: $89
Plate only: $49

Both prices include shipping. 🙂

Garm
KevDWinnipeg, Canada (eh!) · Jul 17, 2011#52
Perfect timing. I'm about ready to get this thing shifting better... Does micro image ship to canada?? Please say yes...
marcustoronto, canada · Jul 17, 2011#53
Originally Posted by KevD ↑
Perfect timing. I'm about ready to get this thing shifting better... Does micro image ship to canada?? Please say yes...
yes sir...i got my ssk from microimage...
KSIbuckyFond du Lac, WI · Jul 19, 2011#54
how do you get that bracket off??? i'm having major problems. I have the trd kit and its hard
cali yarisCanoga Park, CA · Jul 19, 2011#55
^ What kind of problems? Bolts won't come loose? Can't get to them?

Provide some detail, I'm sure everyone will try to help.
KSIbuckyFond du Lac, WI · Jul 19, 2011#56
I have no idea what bolt to loosen
mazillaThread starterSan Jacinto California · Jul 19, 2011#57
Originally Posted by KSIbucky ↑
I have no idea what bolt to loosen


You need to remove these two bolts. The easiest way to reach them is to remove your air intake and your battery. You won't be able to see them, you'll have to find them with your fingers.

Picture not included in this copy
marcustoronto, canada · Jul 22, 2011#59
$49 FOR THE BRACKET EH...*SIGH*.... HOW MUCH TO SHIP TORONTO M1G-1H6.... I SHOULD HAVE JUST WAITED FOR THIS COMBO...ANY DISCOUNT FOR PREV SSK USER OFCOURSE BOUGHT FROM YOU..? JUST CURIOUS GARM?
KSIbuckyFond du Lac, WI · Jul 23, 2011#60
I'm going out to my car right now and trying to loosen those bolts with me luck.

P.s. I already to my intake and battery and idk but ill let you know
KSIbuckyFond du Lac, WI · Jul 23, 2011#61
Originally Posted by mazilla ↑
You need to remove these two bolts. The easiest way to reach them is to remove your air intake and your battery. You won't be able to see them, you'll have to find them with your fingers.
There is no tool known to man that can reach that. I took out my intake and battery and there is just no way. My car is sitting in my garage now with no battery no linkage and no intake because I needed to post this. Did you cut the bracket that holds those wires that are connected to the bracket that holds the shift cables??? Also how do you get the cables out of the bracket???
1NZYaris1New Zealand · Jul 23, 2011#62
Garm do i get 1 as well, PLEASE
solarVitzSan Diego · Jul 23, 2011#63
Sweet. Just ordered the bracket plate only coz i already got the SSK. Cant wait til I put this on my car now. Thanks Garm. 👍

Hey Mazilla what part of SD are you from bro? We should meet up so I can feel how your SSK with the bracket feels like. Text me bro...619-618-5302, Noel.
mazillaThread starterSan Jacinto California · Jul 23, 2011#64
Originally Posted by KSIbucky ↑
There is no tool known to man that can reach that.

If I recall correctly it was a standard 14MM(could be smaller) socket, it should take all of about 5 minutes to get those two bolts off. The bolt heads are going to be facing away from you, you just reach across the engine and using your fingers find the bolt head then slip the socket over and loosen them, you may need a small length of pipe over the wrench handle for added leverage if the bolts are extremely tight. If it's the cables that are blocking you, remove them from the bracket first(see below).


I took out my intake and battery and there is just no way.

It should be very easy at that point...🤷

My car is sitting in my garage now with no battery no linkage and no intake because I needed to post this.

🙁




Did you cut the bracket that holds those wires that are connected to the bracket that holds the shift cables???

No, I didn't have to cut anything.


Also how do you get the cables out of the bracket???

This was the hardest part for me, but it still wasn't a big deal. Apply pressure from the bottom(with a flat head screwdriver or something) and slide those two retaining plates up and off of the bracket. The cables will slide up and out afterwards. I ran my retainers across my buffing wheel a few times, that's why they are all shiny. I figured it would help illustrate the process.

Picture not included in this copy



I'm sorry this is giving you so much trouble...
cali yarisCanoga Park, CA · Jul 23, 2011#65
^ Thanks for the assist Maz.... 🙇
marcustoronto, canada · Jul 23, 2011#66
just need the right tools for it and a leverage/breaker bar and turn clockwise if the bolt is behind to loosen the bolt youll be surprise how some people gets that clockwise , counter clockwise mixed up specially in this situation..
KSIbuckyFond du Lac, WI · Jul 25, 2011#67
i guess ill try again. Im bringing out all the tools
goliath1812Ocala Florida · Jul 29, 2011#68
I couldn't figure out this bracket as well. I can't seem to get the cables out of the old bracket.... 🤷

I was planning on doing this, and the cage bushings I got from Garm, ended up only doing the cage bushings today. 🙁
BEEFnorth carolina · Jul 29, 2011#69
I didn't worry about the bracket for now. I will have more time next weekend (not this weekend) to mess with it. I did like the difference in the short shifter vs stock. I now really wonder how much the bracket helps. I plan to put it on but several people are having a heck of a time with it. if there are any secrets/tips to getting this thing off, I am all ears.
cali yarisCanoga Park, CA · Jul 29, 2011#70
Mazilla had an easy install, as did a couple of other customers so far (not forum members).

When in doubt, consult the Toyota repair manuals, which are published (I think still) on Etimago's site, and maybe on here too.
Lil AbnerDublin, Ohio · Jul 29, 2011#71
Cali Yaris, you've got a typo on your sale page:

"This give a smoother shift feel than the short shifter piece alone."

"give" should be "gives" 😁
cali yarisCanoga Park, CA · Jul 30, 2011#72
Yay, one person read it, lol. I'll fix that thanks!
SAV912Savannah, GA · Jul 31, 2011#73
Just ordered my kit last night, like a fool. On a Sunday. When MI is closed, I presume. XD

Went the whole nine yards and ordered the full kit, AND two quarts of Redline MT90 off Amazon. They should hopefully arrive the same day (crossed fingers) and I'll get to work. I'm pretty thrilled as everything I've done so far is suspension and audio related. Time to get to work on making a little more power and using what is there more efficiently. I started to get a slight third gear grind on quick shifts so hopefully the new fluid will help things.

-C
AltitudeColorado · Jul 31, 2011#74
Originally Posted by KSIbucky ↑
There is no tool known to man that can reach that. I took out my intake and battery and there is just no way. My car is sitting in my garage now with no battery no linkage and no intake because I needed to post this. Did you cut the bracket that holds those wires that are connected to the bracket that holds the shift cables??? Also how do you get the cables out of the bracket???
You can reach them using a socket wrench. Pull out the airbox and the battery tray (and by tray I mean the whole thing bracket and all - you'll need to remove all the plastic clips holding wiring harnesses to it.) The wiring harness bracket mounted to the cable bracket needs to be unbolted.

I think the bolt for the wiring harness bracket is 12mm and the bolts holding the cable bracket are 14mm.

Got mine installed yesterday and the worst part was getting all the plastic clips unmounted from the battery tray bracket. The clips holding the shift cables in the bracket can be a little annoying, but I used a big honkin' flat head screwdriver to pop those out. (Sorry - no pics)

Not a difficult install at all and worth for the improvement in shifting.
cali yarisCanoga Park, CA · Jul 31, 2011#75
^ Good to hear. If you took any pics, we could sure use them!
AltitudeColorado · Jul 31, 2011#76
Originally Posted by cali yaris ↑
^ Good to hear. If you took any pics, we could sure use them!
Sorry - I'm not one to take pics when I do installs - slows me down too much 🙁

I'm curious about those two washers/shims you included...we're they for the bracket mounting bolts? I didn't end up using them and the bracket bolts didn't seem to have any problem going in all the way with the new bracket.
cali yarisCanoga Park, CA · Jul 31, 2011#77
The TRD kit includes two washers. Did the stock bracket use any washers?

They might be to accomodate the difference in thickness between the two brackets?

🤷
AltitudeColorado · Jul 31, 2011#78
Yeah, the stock bracket bolts already had washers. I figured it was to adjust for the difference in bracket thickness but it doesn't really seem to need them.
Black_griffin6Atlanta Georgia · Jul 31, 2011#79
I too am having a lot of trouble with the bracket. I was probably fooling around with it for about 3 hours and never got the stock bracket unbolted, or the shifter cables out of the stock bracket. Which do you do first? Undo the bracket or take the cables out? I still haven't installed the SSK or the bracket yet, since I was to put in the bracket first then put in the SSK. If anyone can post pics, you would be my hero. XD


The good news is I was able to install the shifter bushings for the in cabin and engine bay. 👍 Though, those snap rings are bloody hard to do.
AltitudeColorado · Jul 31, 2011#80
Take the shift cables out of the bracket before unbolting the bracket. You'll have much clearer access to the bracket bolts that way. Also, unbolt the silver wiring harness bracket from the shift cable bracket first too. Aw hell... here's a brief step by step:

- Remove air filter box. (10mm)
- Remove battery.
- Remove battery tray bracket (12mm) (also, unclip as many of the wiring harnesses that you can at this point)
- Remove the pins holding the cables to the shift levers and pull the cables off (careful with the washers)
- Remove clips holding the shifter cables in the bracket. (See below)
- Remove shifter cables from bracket. Push them back towards the firewall until the collar clears the rear of the bracket. Then move them out of the way.
- Remove silver wiring harness bracket from the cable bracket. (12mm)
- Remove the two bolts holding on the bracket (14mm)
- Reverse process.

For the cable clips:

Use a flat head screwdriver - you can wedge it between the exposed cable collar that the bracket slips into and the "L" of the clip itself. Pry, twist do whatever you can to push them up. If you get them up enough you should be able to stick the screwdriver into the gap you just created and pop them out.
Black_griffin6Atlanta Georgia · Jul 31, 2011#81
Okay, that makes much more sense now. Yeah, I saw the silver wiring bracket behind the cable bracket, and I couldn't fit anything behind it to get to the bolts.

I wish these came with instructions. The shifter bushings were pretty self-explanatory, but the SSK not so much. I must be being very blonde today. 😆

I'll probably try it again in the morning, and if I have any luck, i'll post pics to do a DYI for those who were just as clueless as me. 😁
goliath1812Ocala Florida · Aug 1, 2011#84
So the instructions say to access the bracket bolts from underneath the car. Has anyone tried that yet? If so, is it any easier, and do you still need to remove the entire battery tray to get the cables loose from the bracket?

BTW, thanks for the install sheet Garm :)
AltitudeColorado · Aug 1, 2011#85
Originally Posted by goliath1812 ↑
So the instructions say to access the bracket bolts from underneath the car. Has anyone tried that yet? If so, is it any easier, and do you still need to remove the entire battery tray to get the cables loose from the bracket?

BTW, thanks for the install sheet Garm :)
The picture in that PDF is taken from under and behind the engine, though I don't think it's necessary to get at it from underneath. Removing the battery tray gives plenty of room to work on it from above. If you go from underneath I would say you can leave the tray in place.

With the tray removed, it was easy to get a standard socket wrench back there with plenty of room to ratchet (as long as the cables are removed first.)
Black_griffin6Atlanta Georgia · Aug 2, 2011#86
I got it installed! I have yet to try it out though.
SAV912Savannah, GA · Aug 4, 2011#87
Just received mine two seconds ago. DAMN, Garm does not fuck around when it comes to selling things!! Ordered Sunday, got it today. Tracker says he shipped it out Monday morning. That is service!

I'm thrilled. My Redline fluid should be arriving UPS today as well so while I take a crack at the bracket and shifter, hopefully it shows up so I can do the fluid change as well. 😁

Will report back with feedback.

-C
SAV912Savannah, GA · Aug 4, 2011#88
Went outside about half an hour after post above, and just finished. It wasn't an easy install, but not mind boggling either. I printed the TRD directions that Garm posted earlier and while it was helpful as far as tools, the pictures seemed not much of good. They might be pictures of an xD or from an angle that I can't figure out.

Some pointers:
-The battery cable harness is a bitch to keep out of the way so I ziptied it out of the way until I was finished.
-The silver cable bracket that holds some of the battery wires was easily far and away the biggest pain in the ass of the whole install. The short shifter was a breeze and getting to the back of the bracket to change it was relatively easy once I got the damn useless silver cable bracket out of the way.
-I grabbed an extension bar and put an 18mm socket on the end of it and fit that socket over the handle of my breaker bar in order to get more leverage. Somebody short like me would find this very useful since I was already leaning into the engine bay. It also required less pressure to crack the bolts on the back of the bracket this way. Highly recommended for those of you having difficulties getting the bolts to crack. Once they are, it's a breeze.
-Use plenty of lithium grease or liquid wrench to crack the bolts on the bracket itself and to help get the U plates out that are on the shift cables.
-To remove the shift cable U plates, instead of prying at them with a screwdriver (I didn't want to bend them), I grabbed a huge pair of Channelock pliers and clamped on the little lip that they have and wiggled side to side while pulling up. They slid right out really easy after a few futile attempts at prying them up with a flathead.

Impressions:
-I've only been up and down the street with it for now and I still haven't changed the fluid to Redline yet, but THIS. IS. AWESOME. Fore and aft is tight as a virgin now, and it actually enables me to shift with my armrest down now. When I would shift into 4th without the kit, my hand would go almost under the armrest thus having to move the armrest out of the way when in busy traffic.
-About the only negative is the large gap between side to side movement as opposed to fore and aft. I also keep using more pressure going into 3rd and 5th because I'm used to having to push it a bit since the throws were so long. I suppose these are things that I will get used to over time, but overall I am very pleased so far.

Many beers to Garm and Micro Image for this product!! 🍻

-C
cali yarisCanoga Park, CA · Aug 4, 2011#89
^ Nice and thanks! Feedback and reviews are welcomed!

My understanding is that the short shift kit only shortens fore and aft movement, not side-to-side, as a "true" short shifter would. Glad you like the improvement!

Did you do the fluid too? That will further smooth out your shift feel.
SAV912Savannah, GA · Aug 4, 2011#90
Hah, the man himself posts as I'm writing up my prelim review. Thanks again, Garm. This is a fantastic must-have IMO. 😁

-C
SAV912Savannah, GA · Aug 4, 2011#91
Originally Posted by cali yaris ↑
^ Nice and thanks! Feedback and reviews are welcomed!

My understanding is that the short shift kit only shortens fore and aft movement, not side-to-side, as a "true" short shifter would. Glad you like the improvement!

Did you do the fluid too? That will further smooth out your shift feel.
The short shift kit only does fore and aft, you're right. You'd have to put another bracket on the other cable to decrease side to side movement, but I am impressed all the same.

And this is without the fluid yet as it still hasn't arrived. I am faster than UPS going through my neighborhood because the tracker said it was out for delievery at 9 this morning. They had a four hour head start, come on UPS!! Get it together!! 😁

-C
1NZYaris1New Zealand · Aug 5, 2011#92
I am still waiting for mine 😢
buti still you Garm 🤣
malibuguyWestminster, MD · Aug 5, 2011#93
sounds like a great product...i'm still a little weary...i really like how stock feels in both cars
BEEFnorth carolina · Aug 5, 2011#94
malibu,

you are a racer right? get the extender and the short shifter and you get the feel of stock but it is closer to the steering wheel. I did this just because I am used to trucks vs small cars. it is a good feeling.

that is just my 2 cents.
cali yarisCanoga Park, CA · Aug 5, 2011#95
.i really like how stock feels in both cars
If you like it as is, don't change it. For me, the Yaris reminds me of my old Karmann Ghia -- mushy, sloppy shifts.
goliath1812Ocala Florida · Aug 5, 2011#96
well, i had some more time today and went out to try to put the bracket on again. there were a few times trying to get the retainer clips off that i thought about quitting again, but i finally got it, ended up using pliers on the passenger side clip. after the clips came off, everything else was a breeze. haven't gone driving yet with the new bracket, but i'm heading out this afternoon and i'll see how it feels then :)
thanks for everyone's help with the install.
AltitudeColorado · Aug 5, 2011#97
Originally Posted by goliath1812 ↑
well, i had some more time today and went out to try to put the bracket on again. there were a few times trying to get the retainer clips off that i thought about quitting again, but i finally got it, ended up using pliers on the passenger side clip. after the clips came off, everything else was a breeze. haven't gone driving yet with the new bracket, but i'm heading out this afternoon and i'll see how it feels then :)
thanks for everyone's help with the install.
Grats on getting it done. You'll like the new feel (though for me it's going to take some getting used to - I still like it better than stock)
KSIbuckyFond du Lac, WI · Aug 6, 2011#98
having problems with retainer clips how do i get them off??? please help
BEEFnorth carolina · Aug 6, 2011#99
use a really big flat head screwdriver, place it inbetween the bent lip at the top of the retaining clip and the top of the cable (which happens to be metal) and turn the screw driver. this should wedge the retainer clip up. readjust the screw driver a few times and it should losten it enough to get it off. it helps if the tip of the screw driver is 1/2 to 3/4" wide. also depending on your screwdriver design, you can put a wrench around the handle and get even more torque in your twisting.

this may not be the BEST way to do it but it worked for me.
cali yarisCanoga Park, CA · Aug 6, 2011#100
^ That works, and so do channel lock pliers from the top.