Replies continued
PetersRedYarisThe Black Hills of South Dakota · Feb 16, 2009#101 Originally Posted by
Klink10 ↑ That is the torque amount called for....and what I would recommend. Now how to get it there with a big old torque wrench in the small confines is the problem. Ahem....tell you what I did....after replacing with the NST pulley, and replacing the little dowel pin and with the threads on the crank and nut all clean checked by securing on the crank by hand several times....I placed a couple of drops of loctite close to the nuts final resting point and by hand ran it all the way and then hit it hard with the air impact wrench. Just remember to take your time, try it a few times for feel, make sure it goes back the way it came off (just replacing a wheel, nothing else), drop or 2 of Loctite and don't crossthread (why I ran it all the way by hand before impact wrench).
Disclaimer: Torque to limit as specified.
I guarantee you’re not the only one to use an impact... People should know that different impact wrenches vary widely in their power output. It's probably unlikely anyone could strip the threads in the crankshaft or bolt (by over-tightening) because of the materials and size, but no-one wants to damage their new (aluminum) pulley. Just be sure to check the torque outputs on your air wrench; If your wrench has three settings, it's very likely you'll only need to use power I or II.
Many on this forum will be appalled by using a torque wrench to tighten anything, but as always, if you know a better way please share.
frownonfunRGV, Texas · Feb 16, 2009#102hmmm... well today i was off work but really wanted to give this a go so i went to a hardware store and bought an electrical impact wrench just to see. work for me is 90 miles away and i don't usually make a habit of taking my car out that way because i can just ride with the welder i work with anyway. i figured buying a power impact wrench to save me from putting 180 miles on my car was a fair trade. i thought hell i might even get some other uses out of it anyway.
well of course it didn't go as planned... had the car jacked up, wheel off, alternator loosened from the bracket and everything (AGAIN) but the thing just wouldn't budge. so that kinda sucks. guess i will just break down and drive to work tomorrow to use the air impact. a half want to just say screw it and pay someone else to do it cause i'm kinda getting tired of mucking with it at this point. i just had no idea that thing would be on there that dang tight.
Klink10910 · Feb 17, 2009#103Many on this forum will be appalled by using a torque wrench to tighten anything, but as always, if you know a better way please share.[/QUOTE]
No I don't at least in regards to the crank pulley and yea I would and did check my air wrench output when I did mine. You put it better though in regards to the topic. I hope they get it right either way.
jkuchtaL.A. · Feb 18, 2009#104I'm going to be installing the crank pulley soon myself, and was wondering....
Couldn't you just put the car in gear (manual trans), and have a friend step on the brakes while you loosen or torque down the crank bolt? The clutch would hold under 128 ft.lbs. right?
IMO I wouldn't do this mod without a torque wrench...too loose and you could really F-up the crank itself when/if the bolt backs out...plus a loss of the crank pulley will kill the power to the car once the battery dies, leaving you stranded.
Klink10910 · Feb 18, 2009#105 Originally Posted by
jkuchta ↑ I'm going to be installing the crank pulley soon myself, and was wondering....
Couldn't you just put the car in gear (manual trans), and have a friend step on the brakes while you loosen or torque down the crank bolt? The clutch would hold under 128 ft.lbs. right?
IMO I wouldn't do this mod without a torque wrench...too loose and you could really F-up the crank itself when/if the bolt backs out...plus a loss of the crank pulley will kill the power to the car once the battery dies, leaving you stranded.
You could try that....I can't say as I was dealing with an automatic. Chino's DIY at the beginning mentioned tying the pulley down to secure. In the end however he used a air impact gun. The problem with a torque wrench is the limited amount of space to work with and the availability of such a tool to most of the folks doing this mod. I can say that I've done this twice starting with the reg light pulley and then going to the underdrive. On both occasions it took the impact to get it off, which means the impact did its job in putting it on along with a drop of Loctite.
regalPA · Apr 11, 2009#106Sorry to bump an old thread. I know there was a time when the crank pulley served as part of the crank balance on engines. Is there a risk with this Lite pulley throwing off the reciprocating mass and shortening engine life? Why wouldn't Toyota have just made a pulley like this OEM?
"G"Chicago · Apr 12, 2009#107Yes ^ don't do it.
jmjoneseyNorth Carolina · May 13, 2009#108 Originally Posted by
regal ↑ Sorry to bump an old thread. I know there was a time when the crank pulley served as part of the crank balance on engines. Is there a risk with this Lite pulley throwing off the reciprocating mass and shortening engine life? Why wouldn't Toyota have just made a pulley like this OEM?
bump
NonStopTuningUSA · May 13, 2009#109posaunemeisterKansas City, MO · Sep 7, 2009#110Trying to get this OEM pulley off is a pain in the butt, especially since I don't have the proper tools. I think I will put this mod off for a few days until I find someone who will loan me an air/electric impact wrench. The pulley keeps rotating as I try to loosen the middle bolt. I gave up for the night and left everything laying out in my garage. I'm also doing a DIY custom axleback exhaust, so my car is pretty much incapacitated at the moment. 🙂
posaunemeisterKansas City, MO · Sep 7, 2009#111Nothing is going right, it seems. I've decided to just take the Dynomax Super Turbo muffler to the exhaust shop early in the morning to have them weld it on. I went by the common misconception on this forum that our stock exhaust axleback tubing is 1.75", so I purchased a few adapters and clamps for my muffler, went home, cut off the stock muffler and tried to pair the parts together to no avail. It turns out that the axleback exhaust actually measures 1.5" ID (no kidding). Since the space for the muffler is so limited, I decided to not try to make several adapters AND a muffler fill in that space. It just wouldn't make sense. I should've just gone to the exhaust shop in the first place AND I should've measured the exhaust tubing on my own before undertaking this project. You live and you learn. So, I will get up early in the morning and get this taken care of. I feel sorry for those who will be woke up by the blaring sound of my muffler-less exhaust... 😳
Anyway, I'm going to replicate this custom axleback:
Custom Axleback - Pics and vid. , except I will paint my
entire axleback with three coats of high gloss ceramic black spray paint to help retard the rusting, as I live in an area that gets a lot of snow in the winter. Thanks for the inspiration, Largeorangefont.
I also realized that Dynomax makes both their Super Turbo brand mufflers and the Thrush Turbo mufflers and they are pretty much identical in every aspect. They are both aluminized and the locks are spun (not welded). They have identical dimensions. The only difference that I noticed (besides the brand name logo) is that the Dynomax was about one pound (.45 kgs) heavier than the Thrush Turbo, perhaps due to more fiberglass packing or an extra internal wall (?).
On a lighter side, I put out an ad on Craigslist seeking for someone to loan me their electric impact wrench and a kind gentleman quickly responded and doesn't want anything! Of course, I will repay him somehow anyway. But yeah, he has both an electric and the air-compressed variety, as well as a slew of other tools. I have to travel 20min, but I'm sure it will be well worth it. I will post the outcome on here when all is complete.
Cheers! 😉
rhino5Troy, PA · Sep 11, 2009#112So....where did the beginning of this thread get moved to? My pulley will be here tomorrow and I'm sure I'll be able to figure it out...but it'd be nice to have a reference.
AltitudeColorado · Sep 11, 2009#113 Originally Posted by
rhino5 ↑ So....where did the beginning of this thread get moved to? My pulley will be here tomorrow and I'm sure I'll be able to figure it out...but it'd be nice to have a reference.
I would guess it's been moved to the MicroImage forum, though I haven't checked. It's a shame Charles had to remove all of his DIY's for spite.
WeeYariGeorgetown, Ontario, Canada · Sep 11, 2009#114 Originally Posted by
Altitude ↑ I would guess it's been moved to the MicroImage forum, though I haven't checked. It's a shame Charles had to remove all of his DIY's for spite.
Yes, it is on the MI forum. I went there this past Wednesday to walk myself through a NST 10% UDP.
It is a very simple DIY, especially if you have an impact wrench to remove the crank bolt. That is the only potential difficult step if you need to rely on breaker bars to loosen that sucker.
ozmddDFW, TX · Sep 11, 2009#115Wow...if this forum fight is going to continue, I think it will kill both of them. Definitely a turn-off for me.
puetato89orlando · Sep 11, 2009#116 Originally Posted by
ozmdd ↑ Wow...if this forum fight is going to continue, I think it will kill both of them. Definitely a turn-off for me.
+1
posaunemeisterKansas City, MO · Sep 12, 2009#117I just installed mine and I definitely notice a huge difference. The RPMs take off in 1st gear. Before you can even blink your eyes, it's already time to shift to 2nd. The engine is significantly more responsive and the initial take-offs are cleaner & peppy. When you get into the upper mph's, the feels like it works a lot less. It's a different that you, too, will notice.
You will need a torque wrench and an impact gun. I put an ad out on craigslist seeing if someone would rent theirs out to me and I asked if I could do the work in their driveway (makes them more willing to let strangers use their multi-hundred dollar tools). A very kind gentleman, who does his own repair work and works for a wrecker company, let me use all of the tools that I needed, free of charge. I rewarded him handsomely, nevertheless, because I was so taken back by his act of kindness. I love meeting good people like that. He even offered to mount n' balance my wheels if I ever decided to get a set of aftermarket wheels! OK, anyway, It took a total of 45-50min for the install, just like Charles said. It wasn't easy, though. It was actually a huge pain, specifically loosening the lower alternator bolt, even with the long 14mm hand wrench. The upper 12mm bolt on the banana bracket was a breeze to loosen. In order to get the correct tension on your belt after the install, I recommend using a long pry-bar to get the belt at the correct tension and then tighten the upper alternator bolt (easier access), and then the lower bolt. This may require an extra hand.
Btw, I did purchase my pulley from Garm at MicroImage. He shipped it off via USPS Priority Mail and it arrived shortly after. It was an easy transaction with no hassles, and the price was the cheapest I could find online. Thanks, man!
mrbondIllinois · Sep 12, 2009#118WTF chino.
PETERPOOPOahu · Sep 12, 2009#119chino iz ghey
puetato89orlando · Sep 12, 2009#120 Originally Posted by
PETERPOOP ↑ chino iz ghey
lol
cfbrodiericeAlberta, Canada · Feb 2, 2010#121Hello all, I am brand new to the forum. I work on landcruisers and such. I am thinking of buying a yaris for a commuter. Just one thing to say about a lightweight crank pulley... and just my .02....
There is a reason it has a certain weight, so that any vibration in the crank is partially absorbed through the harmonic balancer. you change over to a lightweight and solid pulley and it no longer can do it's job. Ya your engine accels faster, but long term it could make your main bearings wear out faster....
regalPA · Feb 3, 2010#122 Originally Posted by
cfbrodierice ↑ Hello all, I am brand new to the forum. I work on landcruisers and such. I am thinking of buying a yaris for a commuter. Just one thing to say about a lightweight crank pulley... and just my .02....
There is a reason it has a certain weight, so that any vibration in the crank is partially absorbed through the harmonic balancer. you change over to a lightweight and solid pulley and it no longer can do it's job. Ya your engine accels faster, but long term it could make your main bearings wear out faster....
I'm an automotive engineer abd what he is saying is true, going to these aftermarket pulleys is turning your 400k+ potential Yaris into a throwaway car, might as well buy a kia.