Hmm...anyone know what the effect this pulley change will have on an auto trans? Same as manual? Any point in changing it at all?? Wanted to change my flywheel...to a lighter one but turns out i don't GOT one! heh heh...
DIY: Nonstop Tuning CR-Lite Pulley
122 posts · 69,930 views · page 2 of 3
Replies continued
I have the auto, and I can say, the NST pulley made a difference. I am getting better gas mileage, more mid-range torque, a quiet engine, and better acceleration. Not so much "off the line" but very noticeable if you already have some forward momentum and give the accelerator a push. It also weighs about 2lbs less than the stock pulley. I love mine and did notice the difference.Originally Posted by Terrorize ↑Hmm...anyone know what the effect this pulley change will have on an auto trans? Same as manual? Any point in changing it at all?? Wanted to change my flywheel...to a lighter one but turns out i don't GOT one! heh heh...
Cool....thanks dude...in that case i will consider getting it! Heh heh...
Very interesting...
I have a seriously noob question though. Having never tackled anything remotely close to this myself, what keeps the whole pulley/shaft from rotating as you tighten that bolt down to 120+lbs?
~YR
I have a seriously noob question though. Having never tackled anything remotely close to this myself, what keeps the whole pulley/shaft from rotating as you tighten that bolt down to 120+lbs?
~YR
does it void the warranty?? nst pully
If not , I will get one :)
If not , I will get one :)
To answer the question, yes, you will have to hold the pulley while torquing the bolt. It is a small detail I missed in the original DIY, and it has been edited to now include that information.
Here is yet another DIY for the NST pulley on a Scion tC for anyone that wants yet another example of how to install this piece correctly. Sexy car, too... check out the orange rims! 😲
http://www.tunerzine.com/articlestzcorner.asp?id=219
Here is yet another DIY for the NST pulley on a Scion tC for anyone that wants yet another example of how to install this piece correctly. Sexy car, too... check out the orange rims! 😲
http://www.tunerzine.com/articlestzcorner.asp?id=219
How do you 'hold' it?
I would suggest grabbing a friend really quick and having them loop a shop rag or something through one of the holes in the pulley. I explained this in the first post. Sorry for the confusion.
Cool, thanks Chino!
BTW, that Scion is awesome! But what's that odd little red ring on the bumper? Does it talk when you pull the string? 😆
~YR
BTW, that Scion is awesome! But what's that odd little red ring on the bumper? Does it talk when you pull the string? 😆
~YR
LOL! When you pull it the car's hydraulic suspension makes it do a jig.
Actually, its a tow hook for when race cars get into trouble and need to be carted off the course quickly.
Actually, its a tow hook for when race cars get into trouble and need to be carted off the course quickly.
ATTN CHINO
QUOTE
The next step is releasing the tension on your belt. Luckily, these are Toyotas and our namesake made this process very easy. There is a 14mm bolt next to the alternator that sits in a banana-shaped groove. First, mark the position of the bolt so you know how much tension was on the belt stock. Now if you loosen this bolt, the alternator and its pulley will slide forward, thus releasing tension on your belt. It isn't easy, but a quick couple bashings with a prybar and a rubber mallet should do the trick.
where the hell is it?? i cant find no 14mm bolt in / next to the banana shaped grove.....
my car is half hacked and i need to know asap!!!
OR IF ANYONE KNOWS!! PLZ!!
QUOTE
The next step is releasing the tension on your belt. Luckily, these are Toyotas and our namesake made this process very easy. There is a 14mm bolt next to the alternator that sits in a banana-shaped groove. First, mark the position of the bolt so you know how much tension was on the belt stock. Now if you loosen this bolt, the alternator and its pulley will slide forward, thus releasing tension on your belt. It isn't easy, but a quick couple bashings with a prybar and a rubber mallet should do the trick.
where the hell is it?? i cant find no 14mm bolt in / next to the banana shaped grove.....
my car is half hacked and i need to know asap!!!
OR IF ANYONE KNOWS!! PLZ!!
Sounds liek you're looking for something that looks kinda like this

arrrg!!! i did that...nothing came loose nor it moved at all.......and it wasnt 14mm it was 9mm at my end....
edit : the bolt on my "banana" was more than halfway already....though nothing has been mellowed out......stupid banana
edit : the bolt on my "banana" was more than halfway already....though nothing has been mellowed out......stupid banana
aah, there may be a difference in size between the two countries...
I have not done this mod myself, but try and loosen the other screw holding the alternator, maybe it's too tight and won't allow the whole thing to pivot.
I have not done this mod myself, but try and loosen the other screw holding the alternator, maybe it's too tight and won't allow the whole thing to pivot.
tried that too.....nothing loosened up.....i tried "forcing" the thing to move down a bit but nothing budged......
i guess theres different bolt sizes but the process shouldnt be different......
i guess theres different bolt sizes but the process shouldnt be different......
then I'm out of ideas, mate... 🤷
me fookin too....then i was right with the DIY of the "banana" bolt but nothing seems to budge........wtf.....
It ain't easy Hasher! Grab a mallet and a chisel and make her move! That is, after you've loosened that bolt. I'll keep an eye on this thread this morning in case you run into any other issues, or just PM me or send me a message on AIM.
some time you need to loosen up the other bolts up just a tad to get them to move instead of resorting to the hammer
What he said... I just usually resort to hammers. 😆 I'm hoping his lack of response means he had some luck.
Yeah, try loosening that pivot bolt at the bottom of the alternator... if it was too tight, it could probably prevent it from rotating. Maybe they used too much thread locker on it and it gummed up the swiveling part....
~YR
~YR
OOOOOOOOOOOOhhhhhhh STOP..

thanks guy ill try take another stab at it...if it moves or not.....i had to reassemble everything cuz it was like 10pm when i posted my concern....arrhg
yea I just tackled mine right now. Great DIY, the only thing I would like to add on is loosening up that bottom bolt holding the alternator in. It allowed the alternator to pivot a lot easier. I wasn't to keen on beating at it with a rubber malet. That bottom bolt (14mm) was a PAIN IN THE ASS to loosen up. Once I got that off everything else was a breeze.
The DIY has been edited with this information. Thanks for the replies guys.
For fook sake...is it me or my damn car....nothing is going right for me....
i cant take the crank bolt off.....damn stupid bolts why dont they make it simple.....
any tricks of gettin it off without an air ratchet thing?
i cant take the crank bolt off.....damn stupid bolts why dont they make it simple.....
any tricks of gettin it off without an air ratchet thing?
Go to Kragen, Napa, or other lenient return policay auto parts store. Buy an electric impact gun. Gently unpack it. Take off bolt. Put on pulley. Install bolt to proper torque specs. Clean impact gun. Return electric impact gun in original packaging as if never used?!! and yes, I've done it before. 😁Originally Posted by hasher22 ↑For fook sake...is it me or my damn car....nothing is going right for me....
i cant take the crank bolt off.....damn stupid bolts why dont they make it simple.....
any tricks of gettin it off without an air ratchet thing?
ps. if you buy one with adjustable torque, you can put the bolt back on with the gun too. And remember to use loctite.
You might see if autozone has something like that (if they are in your area). They offer a free loan-a-tool program. You pay for the tool, then when you return it they refund your $$ 100%. I've used it quite a bit for tools that I don't often need.
Originally Posted by Astroman ↑You might see if autozone has something like that (if they are in your area). They offer a free loan-a-tool program. You pay for the tool, then when you return it they refund your $$ 100%. I've used it quite a bit for tools that I don't often need.
They have the same thing at Checker Auto. I just used it for a set of strut spring compression clamps.
yea over here in australia i tried lookin for an electric ratchet (other words impact gun?) nothing....stupid stores has sold out...
and too much money for a air ratchet thingy....arrg...
u know what, the pulley is pissin me off cuz of the 14mm crank bolt......next time i get my car serviced im gonna tell them to install it...har har dont care if it costs me $50 or so....bleh
and too much money for a air ratchet thingy....arrg...
u know what, the pulley is pissin me off cuz of the 14mm crank bolt......next time i get my car serviced im gonna tell them to install it...har har dont care if it costs me $50 or so....bleh
breaker bar should only be like $15 bux
I official hate the pulley. There is no way i can take that bolt off. I have snapped 2 wrenches and bent one.....
I have been to hardware shops and they dont sell breaker bars on its own.
Im forced to pay a mechanic to do it for me.....arrrg all becuz that one bolt.
I have been to hardware shops and they dont sell breaker bars on its own.
Im forced to pay a mechanic to do it for me.....arrrg all becuz that one bolt.
lol dude dont give it up. you are pulling the right way right? I know that sounds stupid, but I have done it before. The bolt is very tight, but I dont think enough to be breaking wrenches.Originally Posted by hasher22 ↑I official hate the pulley. There is no way i can take that bolt off. I have snapped 2 wrenches and bent one.....
I have been to hardware shops and they dont sell breaker bars on its own.
Im forced to pay a mechanic to do it for me.....arrrg all becuz that one bolt.
Well I got mine installed today at my favorite workshop 😁
The mechanics had a very hard time taking out the crank bolt too, even with an air tool, but their solution was quite different (and crazy)
One guy put a ratchet on the crank bolt and held it in place TIGHT
Another guy then cranked the engine for half a second. and POP went the crank bolt...
Don't try this at home, thought, it looked like a very easy way to break your arm in two, and cause much damage to the engine bay 😆
No driving impressions yet, though, I left the car there to check the alignment (it veers a bit to the left at highway speeds), and get a nice wash and wax inside and out 🙂
The mechanics had a very hard time taking out the crank bolt too, even with an air tool, but their solution was quite different (and crazy)
One guy put a ratchet on the crank bolt and held it in place TIGHT
Another guy then cranked the engine for half a second. and POP went the crank bolt...
Don't try this at home, thought, it looked like a very easy way to break your arm in two, and cause much damage to the engine bay 😆
No driving impressions yet, though, I left the car there to check the alignment (it veers a bit to the left at highway speeds), and get a nice wash and wax inside and out 🙂
LOL man thats a crazy way to get that bolt off. Actually the problem most of us have been having problem with, is the lower alternator bolt. I actually did not have any problem with the crank bolt, and I used an electric impact wrench.Originally Posted by eTiMaGo ↑Well I got mine installed today at my favorite workshop 😁
The mechanics had a very hard time taking out the crank bolt too, even with an air tool, but their solution was quite different (and crazy)
One guy put a ratchet on the crank bolt and held it in place TIGHT
Another guy then cranked the engine for half a second. and POP went the crank bolt...
Don't try this at home, thought, it looked like a very easy way to break your arm in two, and cause much damage to the engine bay 😆
No driving impressions yet, though, I left the car there to check the alignment (it veers a bit to the left at highway speeds), and get a nice wash and wax inside and out 🙂
I picked the zpi pulley up for real cheap and decided to give it a go. I pulled it off lastnight because the noise was starting to bug me. I was getting a "ting" noise.....so it was removed.......I have pulled it off multiple times and put it back on with the same noise. lastnight i put the original one on and had no noise.
so no more zpi for me.
so no more zpi for me.
What kind of "ting" noise? Like when the motor is colling down? Mine definitley makes a whining noise if you listen to it. You have ot be outside the car though. It's really high pitch. Probably from the aluminum resonating from the belt friction. I've looked to see if it has caused any issues and checked the belt tension and bolt. Everything is fine. It might just be a side affect of the pulley being aluminum. 🤷
yea its not really a constant tinging, more like a "ting ting".....and its very noticable inside the car even with the radio on and even worse outside. Its actually embarrasing having that noise come from a car thats 5 months old.........
im wondering if the nst pulley would be different........
but i actually think there may be a design flaw in the pulley somewhere....
im wondering if the nst pulley would be different........
but i actually think there may be a design flaw in the pulley somewhere....
Mine is NST.
Originally Posted by eTiMaGo ↑Well I got mine installed today at my favorite workshop 😁
The mechanics had a very hard time taking out the crank bolt too, even with an air tool, but their solution was quite different (and crazy)
One guy put a ratchet on the crank bolt and held it in place TIGHT
Another guy then cranked the engine for half a second. and POP went the crank bolt...
Don't try this at home, thought, it looked like a very easy way to break your arm in two, and cause much damage to the engine bay 😆
No driving impressions yet, though, I left the car there to check the alignment (it veers a bit to the left at highway speeds), and get a nice wash and wax inside and out 🙂
Haha... same way I did to install mine. 👍 That crank bolt refused to came out even with the air tool.
x2... don't try this at home!
ZPI has had quality control issues in the past and their pulley is heavier than the NST. That along with Chino's recommendation helped me choose the NST over ZPI and I couldn't be happier. Improved MPG, more midrange to top-end power, and no "noise". Oh also I don't know who said this, but the stock pulley doesn't have any rubber on it. I think a dealer told them this. It's 🙄
The engine fires a piston on every rotation. 4 stroke, 4 piston..............Originally Posted by eTiMaGo ↑
Of course, the disadvantage of removing rotational mass in a 4-cylinder daily driver is the idle quality. The engine needs the heavy weight of the flywheel to keep it going during the 3 non-power strokes. So, when you reduce this mass, the engine will slow down between rotations, and at a lower engine speed (idling), this can make things very rough, even stall the engine.
Why the need for a heavy flywheel? Light means quick acceleration and quick deceleration. Comes down to how the driver manages the car............
hey don't know if someone may have asked this already but how do you keep the stock pulley from turning when you are loosening the bolt.
The main way is use an air impact wrench.Originally Posted by frownonfun ↑hey don't know if someone may have asked this already but how do you keep the stock pulley from turning when you are loosening the bolt.
k... i mean i guess i understand that part, and i can use one of those from work but i just assumed the pulley would still turn to the left whether using a ratchet or impact unless you hold it in place with something.
Not really....with enough force the impact hits it so hard it will spin it right off. I hit mine and it started to turn so I stopped and hit it again...it's technique and if you use them at work shouldn't be a problem. Just get it loose and use fingers to take off. Don't lose track of the little pin and be sure to re-install it.
lol... well i don't actually use them. those just aren't really in my job description. nevertheless i will give it a shot. wasn't sure but now i know.
thank you much.
thank you much.
Getting it off is cake... The real difficult part is torqueing down the bolt to 128ft/lbs when putting the new pully on.
it's not that i doubt you but where did you get this amount from? is that really what it needs to be torqued down at?Originally Posted by PetersRedYaris ↑The real difficult part is torqueing down the bolt to 128ft/lbs
That is the torque amount called for....and what I would recommend. Now how to get it there with a big old torque wrench in the small confines is the problem. Ahem....tell you what I did....after replacing with the NST pulley, and replacing the little dowel pin and with the threads on the crank and nut all clean checked by securing on the crank by hand several times....I placed a couple of drops of loctite close to the nuts final resting point and by hand ran it all the way and then hit it hard with the air impact wrench. Just remember to take your time, try it a few times for feel, make sure it goes back the way it came off (just replacing a wheel, nothing else), drop or 2 of Loctite and don't crossthread (why I ran it all the way by hand before impact wrench).
Disclaimer: Torque to limit as specified.
Disclaimer: Torque to limit as specified.