Yarisworld Archive

Beefing Up my Yaris

84 posts · 21,701 views · page 1 of 2

RacerFreakXXXOriginal postSomers NY · May 1, 2010#1
I've decided to go turbo after a lot of thinking. I'm not going for anything fancy but I want to get the job done right. My goal is to make 130-140whp, my goal spending limit will be $2,500 or less, and my goal time frame completion is summer 2011. I'm going to need your help to piece together what I need. This goal is not including gauges, electronics, EMS. I have a good idea on what needs to be done with all of that.

Here is what I have:
  • ebay Intercooler - $50

Here is what I need:
  • Garrett Dual Ball Bearing GT2554R $900
  • Garms Bottom Mount Turbo Manifold $439
  • Perrin Fuel Rail $180
  • 1zz-fe Fuel Injectors $60 - $100
  • Custom Piping - $500


So far my total is around $2,100 (playing it safe), so that gives me $400 for little things.


Questions:

-What GT25 Garrett turbo should I go with (basically what AR do I want)?

-What other turbochargers might you suggest for cheaper that are rebuilt or new?

-What are the little things I will need?

-What do you guys think of the XA/XB Ebay turbo manifolds?

-Are there any other bottom mount manifolds other than ebay, HKS, & Zage?

Replies 83

RacerFreakXXXThread starterSomers NY · May 1, 2010#3
wow.... I missed that... thank you PETERPOOP. Now that's a lot more than I planned to spend.
cali yarisCanoga Park, CA · May 1, 2010#4
So far my total is around $1,900 (playing it safe), so that gives me $600 for little things.
management: hardware, wiring and tuning. what is your budget for that?
RacerFreakXXXThread starterSomers NY · May 1, 2010#5
Originally Posted by RacerFreakXXX ↑
This goal is not including gauges, electronics, EMS.
ems, wiring, gauges, ect I will figure out... it's the gaskets, lines and adaptors that I really need help figuring out. Oh and a downpipe to go with that turbo manifold of yours, lol.
cali yarisCanoga Park, CA · May 1, 2010#6
are you going to run an external wastegate?
cali yarisCanoga Park, CA · May 1, 2010#7
Garrett GT2554R is what I used, it was an awesome little turbo. I'll be using that one for the kit I'm making.
RacerFreakXXXThread starterSomers NY · May 1, 2010#8
Well that's good, and it's cheaper than the GT2560R. So you will be selling an actual kit turbo within the next year or will it be a step by step and sell it when it's done?
cali yarisCanoga Park, CA · May 1, 2010#9
I'll be selling parts as I make them and a complete kit when a stock test car drives around boosted for a month without CELs.
RacerFreakXXXThread starterSomers NY · May 1, 2010#10
well I'd be happy to be your test car, lol
PETERPOOPOahu · May 1, 2010#11
The MicroImage turbo kit, I believe, will also not have any management.
cali yarisCanoga Park, CA · May 1, 2010#12
^ that is the goal.

racer, add a BOV to your list
RacerFreakXXXThread starterSomers NY · May 2, 2010#13
I'm not 100% on the bov... I'm also trying to see if I can run a turbo at low boost with little to know help from an ems. What do you plan to include in your kit?
cali yarisCanoga Park, CA · May 2, 2010#14
Why are you not 100% on a BOV?
ParmasML · May 2, 2010#15
Hi RacerFreak

Making a custom turbo setup is not easy and cheap as it seems. If you plan $2500 you might think of another $1000 for what you might forgot.

1. A BOV is not an option but a must so you must include that

2. Decide whether you are going internal or external wastegate. My opinion for low boost applications till 7psi, an internal wastegate of the Garrett turbo itself is good enough

3. Decide what intercooler fits best for your needs and looks. A top mount IC would be cheaper and is good for low boost while a front mount IC requires fitment, more expensive to buy but looks awesome. Don't forget the custom intercooler piping to add to the list.

4. Upgrading the fuel pump to a higher flow rate one is an insurance and might aswell need it to keep up fuel during boost. Also consider adding a fuel return line to the setup.

5. Also consider upgrading the fuel regulator to an aftermarket one

6. Maybe the stock clutch might hold but not for long. Try a stage 1 exedy clutch to be safe.

All parts can be cheap or expensive depending on brand and efficiency. My opinion is that to invest in quality parts as these are that assure your motor to work safe when you sometimes hit the gas more roughly 🙂

Hope this helps
cali yarisCanoga Park, CA · May 2, 2010#16
^ I agree with almost all of that. 🙂 I'm a confirmed Clutchmasters fan now, I've used both and it's just a better clutch.
lilredrocketDFW, Texas · May 2, 2010#17
If your goal is only 130-140ish HP why not go stage 0? No intercooler and run a water/meth kit. You are probably only going to be running 5psi.
ParmasML · May 2, 2010#18
Originally Posted by lilredrocket ↑
If your goal is only 130-140ish HP why not go stage 0? No intercooler and run a water/meth kit. You are probably only going to be running 5psi.
A meth kit isn't cheap to buy and to install and you need to refill it when it's needed. An intercooler has no day to day to take care of and costs about the same compared to an average intercooler
LorenSafety Harbor, FL · May 2, 2010#19
I'm scratching my head trying to figure out why, with the given goal of 130-140whp, you don't just go with a readily available and proven supercharger kit. You'll end up spending more on a custom turbo kit in the long run.

Expand your $2500 budget to $3000-3400 and you get a plug & play kit that meets your goals without trial and error.

If you want MORE power than that, then you need to go through the trials and tribulations of a custom turbo kit, fuel management, possibly forged internals, lower compression pistons, yadda yadda. But, if all you want is 130 hp...
cali yarisCanoga Park, CA · May 2, 2010#20
^ these are good points.

Meth kit is about $300, and a gallon will last for weeks, just to be clear.

I'm not saying its necessary, either. You'd have to tune for it, which means management.

I don't think it is needed for 130-140, probably can do that with a Stage 0 and no water/meth.
H3LlIoNMidatlantic · May 2, 2010#21
Originally Posted by Loren ↑
I'm scratching my head trying to figure out why, with the given goal of 130-140whp, you don't just go with a readily available and proven supercharger kit.

A couple things regarding this....

First, the blitz will not put down a buck thirty by itself. "Turbo" magazine installed it and only got to 119hp. Link Here.

Secondly, there is very little upside to the blitz. If you want more boost, you first have to convert it to fixed pulley, instead of electronic, which is unproven ground as, to my knowledge, noone has done it. Then, you have to drop to lower comp pistons, since more boost on our factory 10.5:1 pistons will cause issues. Past that point, the s/c is capped at a (roughly) 9 to 10 psi on the housing before you leave the safe operating range.

At the very least, you would need to run s/c with additional bolt ons.
RacerFreakXXXThread starterSomers NY · May 2, 2010#22
1. A BOV is not a must for a stage 0/1... there are plenty of stock turbo cars w/o them, however I may get one.

2. I know I'm going to do an internal wastegate.

3. I already have a front mount intercooler.

4/5. The return line and pump are probably going to happen with this build and I may also use a fuel pressure regulator too.

6. I am planning on a clutch and a diff but those are not part of my turbo build, I was planning on that before I decided to go turbo.

I'm not planning on boosting like crazy, I just want something that can get me to my power goal. I'm not planning on winning any races or anything fancy like that. The Yaris just feels like it needs more power so I'm not always going through the gears to get the car up to speed.

My price is for a turbo build, not tuning and all the supporting mods. I am pricing this like a turbo kit. The average turbo kit is 3-3.5k with piggyback EMS and intercooler.
cali yarisCanoga Park, CA · May 3, 2010#23
1. A BOV is not a must for a stage 0/1... there are plenty of stock turbo cars w/o them, however I may get one.
Right. On some STOCK cars, which is not what you are building.

Um, since you already got an intercooler (see #3 above), you are building a stage 1. Right?


Blowoff valves are used to prevent compressor surge, a phenomenon that readily occurs when lifting off the throttle of an unvented, turbocharged engine. When the throttle plate on a turbocharged engine closes, the high pressure air in the intake system is trapped by the throttle and a pressure wave is forced back into the compressor. The compressor wheel slows rapidly and may even stall, and the driver will notice a fluttering air sound. The rapid slowing or stalling stresses the turbo and imparts severe turbo lag if the driver accelerates immediately after the surge event.
kounj · May 3, 2010#24
Just buy the hks turbokit for the xa/xb and modify the downpipe $2700
PETERPOOPOahu · May 3, 2010#25
Originally Posted by kou ↑
Just buy the hks turbokit for the xa/xb and modify the downpipe $2700
don't forget to tell him that noone has done this yet.
ParmasML · May 3, 2010#26
RacerFreak why don't you try to find a 1NZFE TRD edition if you want only 130HP. It comes turbo standard with factory management and wiring.

Check this link Just wanted to share this: turbo 1NZFE

I know ppl who done this in our country and reached 150HP without much complications
Nexus1155Dorchester · May 3, 2010#27
What pump are you talking about?

and what FPR? I thought these were returnless fuel systems or whatever, need to modify it to use an FPR?

Also you can just run off the internal wastegated pressure, usually around 7-9 psi in most cases. Look up an SR20 turbo, it will fit the GT28 flange.

You can go to the junkyard and get a recirculating valve which you should get or even a BOV from a stock turbo DSM with the piping as well that comes with it. Very easy to take off and get.

If you are running intercooler piping, might as well, right?
RacerFreakXXXThread starterSomers NY · May 3, 2010#28
Originally Posted by PETERPOOP ↑
don't forget to tell him that noone has done this yet.
I know no one has done this, not even the xb guys. I am better off with chinese turbo kit than I am a hks kit. I'm going to go with garms well built parts and get custom piping locally. Also, buying an engine is out. If I had a garage I would just buy a spare engine and build it and then swapp it, but I'm going to still consider it if I can find a place to do the swapp.

For EMS... I'm probably going to go with greddy, seeing as it has been proven.

In all honesty I am going to get a greddy RS BOV unless I cant fork up a coupple hundred dollars.

For turbo's, I think Garrett is going to be my best bet for the price. If I can find a new turbo for $400-$500 then maybe, but I doubt I will find a dual ball bearing water/ oil cooled T25 turbo for that much.

Garm if/ when you make a downpipe, you should have the option to put on a bung for a/f sensor.
cali yarisCanoga Park, CA · May 3, 2010#29
My downpipe will have TWO bungs. One for managemenet, one for a gauge, and tuners love an extra bung for dyno day. 👍
RacerFreakXXXThread starterSomers NY · May 3, 2010#30
Nice... look at you thinking ahead, making life easier. I don't get why manufacturers make parts so expensive but they still need to be modded. I look forward to your kit... will you be making piping for a front mount intercooler?
rob323Joyner, Brisbane · May 13, 2010#32
A Mitsi 16G turbo is a 300+ hp turbo (both small and big 16g's) and don't really start to get efficient until 17+psi. Waaaaaay too big for your application.
Even a standard 14b Mitsubishi Galant VR4 (DSM Talon/ Eclipse) turbo is a 200hp turbo and might be too large considering it's designed for engines with a capacity of 2litres. A TD04 off an auto version would be better suited but you would need to find one second hand and have it rebuilt just to be safe.

I can't think of any Mitsi turbo's that would be "ideal" for your application and would probably stick with a bb Garrett, or, dunno if you get them over there, one of the small IHI turbo's off a late '90s Subaru WRX, they were quite small and guys use them as big upgrades on Starlet GT's over here as they are plentiful and cheap.
ParmasML · May 14, 2010#33
4/5. The return line and pump are probably going to happen with this build and I may also use a fuel pressure regulator too.
Just noticed that I missed that you must upgrade your fuel rail to accept the return line.
RacerFreakXXXThread starterSomers NY · May 14, 2010#34
I'm going with the perrin fuel rail, as listed in my first post. My main concern are the oil likes and vacume lines and all of that little stuff. Should I tap the oil pan or buy an aftermarket?
cali yarisCanoga Park, CA · May 14, 2010#35
We don't really have an oil pan, it's more of a plate; you would have to tap the lower block (like I did). Or get a deeper oil pan, but then you will have the worry of clearance issues when driving around.
H3LlIoNMidatlantic · May 14, 2010#36
IIRC one of the turbokit manufacturers makes an oil pan cast with a hole for turbo oil, so check greddy, hks, etc...it's billed as for the xB, but engine is same.
ParmasML · May 14, 2010#38
Originally Posted by RacerFreakXXX ↑
I'm going with the perrin fuel rail, as listed in my first post. My main concern are the oil likes and vacume lines and all of that little stuff. Should I tap the oil pan or buy an aftermarket?
Mine Turbo Oil Feed is tapped into the lower block.... just a few inch below the knock sensor position ( behind intake manifold )
RacerFreakXXXThread starterSomers NY · May 15, 2010#39
I noticed the pn like shape of our oil pan, maybe i'll check on the scion forums and see if any of the guys have luck with the oil pan. Tapping the block scares me for 2 reasons: first I'm worried me or someone I have do it, will screw it up and secondly I'm worried if I ever need to bring the car back to stock, I wont be able to.
TamagoOff Grid · May 15, 2010#40
ahh yet another turbo thread.
RacerFreakXXXThread starterSomers NY · May 15, 2010#41
from me too, lol... any advice tamango? or are you going to just troll this one?
TamagoOff Grid · May 19, 2010#42
Originally Posted by RacerFreakXXX ↑
from me too, lol... any advice tamango? or are you going to just troll this one?
it's tamago

and yes, trolling. if you took the time to search, all of your questions have been answered over and over and over and over.

low boost won't require an intercooler.
PETERPOOPOahu · May 19, 2010#43
tamagay
TamagoOff Grid · May 20, 2010#44
Originally Posted by PETERPOOP ↑
tamagay
Matt Cavanaugh
cali yarisCanoga Park, CA · May 20, 2010#46
LOL @ everything
ParmasML · May 21, 2010#47
Originally Posted by cdydjded ↑
There are NO significant drawbacks to an I/C. It only helps with the additional air you are pumping into the engine.
There is always a drawback!

Drawbacks of installing an I/C is mainly Boost Lag depending what are the:

- I/C dimensions, Intake and Outake width ports and I/C Brand Quality

- Turbo Specs and Brand

- I/C pipping width and distance between turbo & throttle body


And then there are also...

- Fitment issues or Complications

- Increased Weight and Decreased space into the engine bay

- Surplus total expense to cover all parts and labour

I think that might be all 🙂
CtrlAltDefeatIndianapolis IN · May 21, 2010#49
Originally Posted by PETERPOOP ↑
tamagay
Originally Posted by Tamago ↑
Matt Cavanaugh
Originally Posted by PETERPOOP ↑
Joel Geisinger w/ white hair? maybe not...

Picture not included in this copy



ps: www.myspace.com/themattcavanaughexperience
Originally Posted by Tamago ↑
proving your gay obsession yet again

now now children, if you can't get along, we will just have to put your toys away... 😆
ParmasML · May 21, 2010#50
Originally Posted by cdydjded ↑
Here a link to a article that rebuts most of your points:
http://www.torquecars.com/tuning/aft...ntercooler.php

Read it if you want. If not thats ok. We will agree to disagree on this point.
Yes I read the article and this is the most important sentence of all :

"In reality using an intercooler which is too large can hinder airflow so there is an important case of getting the correct size for the application"

I am not saying an i/c isn't important, I just pointed out the drawbacks of having it but that doesn't mean it's not worth it!