Yarisworld Archive

2008 Yaris sedan ‘S’ sound deadening project.

155 posts · 121,707 views · page 1 of 4

HerbicidalOriginal postRoseville, CA - USA. · Apr 24, 2010#1
First off I would like to say thank you to DerickVeliz2, SQComp, Swidd, Talnlnky and countless others I have learned from in just the last week alone! 👏

So I’m sure some of you are thinking, Oh no! Not another sedan sound deadening project! 🙄 When I started mine, I didn’t even realize there are several other ‘works in progress’. My goal is not the same as theirs regarding the level of deadening they are going to achieve. I’ll be a couple of steps down. Nor am I going to upgrade my sound system to their levels either. I’m staying with the stock head unit and only upgrading the speakers. I need to draw the $$$ line somewhere.

Before I started, I wanted to scientifically document the difference of my sound deadening efforts. I bought a small digital decibel meter and took some readings inside the car under full acceleration with the windows up and the radio off. I was a little surprised by the readings! See pictures below for more info.

I’m starting in the trunk and working my way forward. I guess it all started after I had my custom center exit exhaust installed. Even after a muffler and two straight through resonators, the sound inside the car under acceleration is still a little too loud for my tastes. However, the exhaust note outside the car is just right!

To begin, I pulled all the plastic panels from the trunk, trunk mat, spare tire, etc. It all came out quite easily. Then I wiped the metal surfaces down with rubbing alcohol. My sound deadener of choice is from www.RAAMaudio.com. More specifically, RAAMmat BXT II. It comes in 15” x 15” squares with soft foil on one side and a peel and stick adhesive on the other. This product is VERY easy to use and does not cut you. I can cut it with a pair of scissor I keep in the garage. I use the left over backing as template material for those oddly shaped spaces. I also bought 9 square feet of Ensolite foam that is also peel and stick. At the moment, I plan on using the Ensolite in the door panels when I get to them. I realize now that I probably don’t have enough.

At this point I have completely deadened the truck and trunk lid. I’ve removed the rear seat and subframe and the plastic parts that cover the wheel wells. Tonight I removed the rear speaker deck and the plastic pieces along the back of the rear seat. I would like to stuff some kind of foam up the “C” pillars.

I figured while I was tearing into my car, now would be a good time to upgrade the speakers. After a bunch of quick research on Crutchfield I found speakers that I like and were given high marks by previous buyers. I was pretty much ready to buy from Crutchfield when Swidd posted up a link to www.SonicElectronix.com. The rear speakers were $60 LESS then Crutchfield. So that’s were my money went. For the rears I ordered up a pair of Alpine SPR-69C for $99.99 . For the fronts I agonized whether to go with a straight replacement or get a pair with separate tweeters. Separates mean that I will need to cut the door panels. The separate tweeters won out in the end. I ordered a pair of Kicker KS60.2's for $109.99.

Here’s some pics of where I’m at so far.

Getting started: RAAMmat, Ensolite foam (both are peal and stick) with a digital decibel meter.
Picture not included in this copy

Closeup view of the mini decibel meter.
Picture not included in this copy

Taped to the rear seat to get a baseline sound reading.
Picture not included in this copy

Highest sound I recorded in the cabin, 84.7 db.
Picture not included in this copy

Removal of the trunk "stuff". When was the last time you checked the air pressure in your spare?. 😁
Picture not included in this copy

Rear "stuff" removed and the metal surface wiped down with rubbing alcohol.
Picture not included in this copy

Partially done trunk. Right hand side.
Picture not included in this copy

I used the leftover backing for template material.
Picture not included in this copy

Figured out an easier way to remove those, those, pluggy, clippy things. A ziptie fits through the head and now you can pull them out with out prying the head off or damaging them.
Picture not included in this copy

RAAMmat in the trunk lid. I’ll make sure to deaden the license plate and frame too.
Picture not included in this copy

Trunk and deck lid about 95% done at this point.
Picture not included in this copy

Pretty much done with the trunk. This is the drivers side. I may have to put some foam over the vent to dampen the sound, but still allow air movement.
Picture not included in this copy

Trunk, passenger side.
Picture not included in this copy

Inside the car, facing the left rear corner, taking the picture from behind the passenger side front seat. I've finally uncovered the wheel wells!
Picture not included in this copy

Rear seat, subframe and wheel well panels removed. You can see where I stopped from the trunk.
Picture not included in this copy

Now I can pretty much work up to the back of the front seats after lifiting up the carpet.
Picture not included in this copy

Inside the car looking towards the trunk. The rear deck topper and the factory sound deadener is flopped over on the right laying in the trunk. Kind of hard to get the depth perspective in this picture.
Picture not included in this copy

From the front seats looking toward the back. You can see the left wheel well that I want to deaden too.
Picture not included in this copy

A semi-closeup of the rear deck minus the deck material, etc. The speakers are reflecting in the rear window. All of that bare metal I want to deaden.
Picture not included in this copy

Should be interesting to get another db reading after I'm done. I may take some other readings, like before and after doing the doors. Also, like the others are doing with their projects, I’ll post up as I go.

Replies 154

Kaotic LazagnaCentral Valley, CA · Apr 24, 2010#2
Nice. Just for shits and giggles, take a dB rating after you break in the speakers. hahaha.
swiddCentral Alabama, GOD BLESS AMERICA · Apr 24, 2010#3
wow, clean and thorough :) I attacked it like a zombie, ripping off the panels, throwing them aside, slapping on some mat, cutting up some patches of foam, and banging the panels back on. Banging extra hard if they would not quite fit.
talnlnkySpokane, Wa · Apr 24, 2010#4
hmmm raammat used to come in like 50ft long rolls... wonder why it's cut into squares now. Different supplier maybe.
Nice trick with the clips....I can't remember how I got those out (it was 2 yrs ago... hehe)
HerbicidalThread starterRoseville, CA - USA. · Apr 24, 2010#5
Originally Posted by Kaotic Lazagna ↑
Nice. Just for shits and giggles, take a dB rating after you break in the speakers. hahaha.
Will do!

Originally Posted by swidd ↑
wow, clean and thorough :) I attacked it like a zombie, ripping off the panels, throwing them aside, slapping on some mat, cutting up some patches of foam, and banging the panels back on. Banging extra hard if they would not quite fit.
Thanks!

Originally Posted by talnlnky ↑
hmmm raammat used to come in like 50ft long rolls... wonder why it's cut into squares now. Different supplier maybe.
Nice trick with the clips....I can't remember how I got those out (it was 2 yrs ago... hehe)
I think that's the "original" version, BXT. The squares do make it easy, but rarely have I used an entire square at one time. Maybe as I get further into the passenger compartment...

I just checked the status of my speaker order and it's already is Sacramento! Looks like I should get all 4 on Monday. C'mon Monday! 👍
talnlnkySpokane, Wa · Apr 24, 2010#6
unfortunately.... unless you spend $500 or more on an spl meter, any value above about 110-120 just isn't going to be accurate. But.... spl meters, even the cheaper ones are fun toys to play with.
HerbicidalThread starterRoseville, CA - USA. · Apr 24, 2010#7
No worries! Like you said, a fun toy to play with. I guess my experiment is more un-scientific, then scientific, but hopefully better than just saying "yeah, that sounds quieter". At least I'll have some numbers to look at.
1NZYaris1New Zealand · Apr 25, 2010#8
👍 nice ,and i would 100% agree , at least in your own heart you
know exactly how much noise reduction you have achieved.
hmm until the sterio is turned on 🤣 😁
keep the pics coming .
DailyDriverutah · Apr 25, 2010#9
excited to see how this turns out. more pics the better! THX!
yaris2010RSAngus, Ontario · Apr 26, 2010#10
question...... when applying the RAAMmat, what do u do? cover all the metal? i want to do this but its expensive stuff..... and to cover all the metal would use alot of stuff.....

thanks
goku87AK · Apr 26, 2010#11
Originally Posted by talnlnky ↑
hmmm raammat used to come in like 50ft long rolls... wonder why it's cut into squares now. Different supplier maybe.
Nice trick with the clips....I can't remember how I got those out (it was 2 yrs ago... hehe)
It changed (if I can remember correctly) about the time I got back from my deployment (I think) about a year ago, give or take a few months. They said it was better for shipping and ease of use.
sqcompBack at home · Apr 26, 2010#12
Rick sells good stuff. I actually have to get a hold of him to get a Raamaudio decal/sticker for the back windshield...
derickveliz2Central, MA · Apr 26, 2010#13
Originally Posted by yaris2010RS ↑
question...... when applying the RAAMmat, what do u do? cover all the metal? i want to do this but its expensive stuff..... and to cover all the metal would use alot of stuff.....

thanks
Yes, that is the idea and many layers are required to block noise , and Yes it's expensive. But it's worth the effort! I'm in the middle of the process and I'm already feeling the good results, I'm using a different approach than the one shown here, but even every little you do, it's a great benefit.

D.
👍

.
HerbicidalThread starterRoseville, CA - USA. · Apr 26, 2010#14
Originally Posted by yaris2010RS ↑
question...... when applying the RAAMmat, what do u do? cover all the metal? i want to do this but its expensive stuff..... and to cover all the metal would use alot of stuff.....

thanks
You can also be more selective on where you put the sound deadener. Probably the biggest bang for the buck would be doing the doors, which I'm actually doing last. 🙄 See Derickveliz2's outstanding thread for more details. You can also look at RAAMaudio's web page in the How-To section ->doors. In fact, I think it's a good idea to review the whole How-To section, then you can decide how much you want to do and where. 👍
talnlnkySpokane, Wa · Apr 26, 2010#15
Generally you want to cover as much as possible, add as much weight as you can do the panels. However...

for those on a budget you can maximize the limited material you do have and instead of carpeting all the metal with the stuff just cover say 40-50% of each flat panel of metal with some of the mat. The are diminishing returns after that. With that said, I went 3 layers deep where the rear passengers feet rest... most places I have 1-2 layers tho. IN the future I intend to put about 30sq feet on my front two doors, and another 30ft on my firewall.
HerbicidalThread starterRoseville, CA - USA. · Apr 26, 2010#16
Originally Posted by talnlnky ↑
Generally you want to cover as much as possible, add as much weight as you can do the panels. However...

for those on a budget you can maximize the limited material you do have and instead of carpeting all the metal with the stuff just cover say 40-50% of each flat panel of metal with some of the mat. The are diminishing returns after that. With that said, I went 3 layers deep where the rear passengers feet rest... most places I have 1-2 layers tho. IN the future I intend to put about 30sq feet on my front two doors, and another 30ft on my firewall.
That's one way to lower your car without the use of aftermarket springs! 😁

My speakers arrived today! Woohoo! I haven't even opened the box yet. I'm relishing the moment... And placed another order for some more RAAMmat and Ensolite. That should allow me to complete the car and hopefully have some leftover to start either the Tundra or the wifes Corolla. 👍
HerbicidalThread starterRoseville, CA - USA. · Apr 27, 2010#17
I had a whopping 1/2 hour to work on my car last night. I'm not going to pull multiple all-nighters like Derick! I need my sleep! 😛

I did remove the stock rear speakers without damaging the rear window tint. I also popped out the rear "C" pillar covers as I want to get some sound deadening material up there too. And took the new speakers out of the boxes. Here's some new pictures:

Alpine Type R rear speakers. Ya baby!
Picture not included in this copy

Kicker door speakers with electronic crossover and tweeters.
Picture not included in this copy

Left rear "C" pillar panel removed. Both rear speakers removed.
Picture not included in this copy

Right rear "C" pillar panel removed. Notice the stock speaker sitting there...where's the magnet?!? Ohhhh! There it is! Look really close..!
Picture not included in this copy
derickveliz2Central, MA · Apr 29, 2010#18
Where did you buy the digital decibel meter? and how much did you pay for it?
talnlnkySpokane, Wa · Apr 29, 2010#19
those aren't usually called electronic crossovers. They are normally just called passive crossovers because they don't require a power source to operate. If you call them electronic crossovers, people might think you are talking about active crossovers which are the crossovers built into your amplifier, or a stand alone powered crossover like this

Also, passives 99.9% of the time are installed in line with the speaker wire, where as active is installed in line with the signal cable(RCA's). that .1% of the time I alluded to are things called Fmods

Hope you have a free weekend, cause you have your work cut out.
HerbicidalThread starterRoseville, CA - USA. · Apr 29, 2010#20
Originally Posted by derickveliz2 ↑
Where did you buy the digital decibel meter? and how much did you pay for it?
From HERE. Basically $30.

Originally Posted by talnlnky ↑
those aren't usually called electronic crossovers. They are normally just called passive crossovers because they don't require a power source to operate. If you call them electronic crossovers, people might think you are talking about active crossovers which are the crossovers built into your amplifier, or a stand alone powered crossover like this

Also, passives 99.9% of the time are installed in line with the speaker wire, where as active is installed in line with the signal cable(RCA's). that .1% of the time I alluded to are things called Fmods

Hope you have a free weekend, cause you have your work cut out.
I stand corrected! Thank you! 👍
HerbicidalThread starterRoseville, CA - USA. · Apr 30, 2010#21
Well I managed to squeeze in maybe two hours tonight. I worked on deadening the right wheel well (just behind the white bottle of rubbing alcohol) and just about all of the rear deck. Next will be the drivers side rear wheel well, the floor under the rear seat and up to the back of the front seats, then I think I can install the rear speakers and put the back 1/2 of the car together again so I can drive it. After that, I think I will work on one door at a time. In the upper left corner of the picture you can see some wire and connectors. To much of a pain in the ass to deaden right there, so I put the RAAMmat on the inside of the 'C' panel plastic piece instead. Should work fine. One of my neighbors kids came by for a look and said "that's cool!". Made my night. 🙂

Here's just one pic from tonights work.

Picture not included in this copy
HerbicidalThread starterRoseville, CA - USA. · May 1, 2010#22
Well I realized last night that I overlooked getting some kind of speaker adapter to mount my new speakers in. 🙄 So after some internet searching I found Car Speaker Adapters.com I found a set for the rear 6x9's and for the fronts too. They have already shipped via USPS, so hopefully by the middle of next week I'll have them. In the meantime, I'll continue with sound deadening, so by the time they arrive I should be ready to put the back 1/2 of the car together again.
sqcompBack at home · May 1, 2010#23
Herb...

Did you have that nasty metal anchor on the C-pillars like I did? You knw, in the area that you didn't want to deaden because of the clips...
HerbicidalThread starterRoseville, CA - USA. · May 1, 2010#24
Originally Posted by sqcomp ↑
Herb...

Did you have that nasty metal anchor on the C-pillars like I did? You knw, in the area that you didn't want to deaden because of the clips...
No I didn't. You can just see one of the C pillar panels laying backside up (has a blue connector up in one corner) and there were like only 4 connectors I had to pop out. The panel on both sides came out real easy. I used a long screw driver to get next to each connector and slowly worked it out. No problem whatosever.
sqcompBack at home · May 1, 2010#25
Okay...So you DON'T have the curtain airbag option? Just making sure. I know there is a metal "stud" (for lack of a better descriptor) that anchors the c-pillar in mine. Boy was it a headache to get off...
HerbicidalThread starterRoseville, CA - USA. · May 1, 2010#26
Originally Posted by sqcomp ↑
Okay...So you DON'T have the curtain airbag option? Just making sure. I know there is a metal "stud" (for lack of a better descriptor) that anchors the c-pillar in mine. Boy was it a headache to get off...
Correct. No side air bags. Interesting that you do! 🤷
sqcompBack at home · May 2, 2010#27
It was an option that seemed good to have.
HerbicidalThread starterRoseville, CA - USA. · May 2, 2010#28
Originally Posted by sqcomp ↑
It was an option that seemed good to have.
Agreed! My car was already built and sitting on a different dealers lot, not an option for me.

Spent a couple of more hours on it tonight. Kind of reached a milestone, at least for me anyway. I have almost reached the start of the carpet at the base of the rear seat. I'm almost done with RAAMmat for this 'phase'. Just a few more wide strips to get to the carpet. I plan on putting some Ensolite on the wheel wells to further reduce tire noise at those points. I may put some up on the "C" pillars too since that's about ear level with rear passengers.

Here's few pics from this evenings efforts.

98% done with rear as far as RAAMmat is concerned. I'm pretty well protected from aliens reading my brain waves, as long as I'm in the trunk. 😛 Oh, at the very back you can see bare metal. At the point in the trunk, it's double-walled and putting the RAAMmat there wouldn't really accomplish much. Maybe I'll do a strip of Ensolite there instead.
Picture not included in this copy

Looks like a giant Jiffy Pop popcorn container!
Picture not included in this copy

Several places I deadend the "C" pillar panels since there was stuff in the way on the body of the car. Hey! I just noticed I'm missing a triangle piece on the left one. And the one on the right is missing a small piece too! I'll fix that tomorrow.
Picture not included in this copy

Hopefully I'll have some time tomorrow to place some Ensolite in there and maybe pick up some thick foam to put in the large space beneath the rear seat when it goes back in.
sqcompBack at home · May 2, 2010#29
Tell me Rick isn't the $hit. I'm using his Ensolite...good stuff.
derickveliz2Central, MA · May 2, 2010#30
Looking GOOD!
HerbicidalThread starterRoseville, CA - USA. · May 2, 2010#31
Originally Posted by sqcomp ↑
Tell me Rick isn't the $hit. I'm using his Ensolite...good stuff.
AND he's a really nice guy to deal with!

Originally Posted by derickveliz2 ↑
Looking GOOD!
Thanks! Coming along, slowly but surely. I'm going to try and get in another two hours this evening.
derickveliz2Central, MA · May 2, 2010#32
Originally Posted by Herbicidal ↑
Coming along, slowly but surely.
Hey 👎 I quit writing my hours in a log... it was embarrassing 😳

Take your time!

That's what I do. 👍
D.
HerbicidalThread starterRoseville, CA - USA. · May 3, 2010#33
Originally Posted by derickveliz2 ↑
Hey 👎 I quit writing my hours in a log... it was embarrassing 😳

Take your time!

That's what I do. 👍
D.
Wow! I never even thought of keeping a log! Glad I didn't. 😛 Man, I love working with the Ensolite (peel and stick version)! 👍 Much like the RAAMmat, smaller sections work best since it sticks to everything! However, it's very easy to remove and reposition until you push it into it's permanent place. Last night I mostly completed the rear wheel wells and the floor area directly below the rear seat. Started on a section of the rear deck too. At this time, I am not going to do the trunk with Ensolite, just within the passenger compartment. No pics yet. I'm coming down with some kind of bug, so I went to bed early.
derickveliz2Central, MA · May 3, 2010#34
Originally Posted by Herbicidal ↑
Wow! I never even thought of keeping a log! Glad I didn't. 😛 Man, I love working with the Ensolite (peel and stick version)!
That's the same stuff I'm getting from http://raamaudio I was tired of using the 3M 77 spray on the trim panels, Rick just changed his website but still offers the same materials. Also got more CLD Tiles from sound deadener showdown
HerbicidalThread starterRoseville, CA - USA. · May 4, 2010#35
I ordered my speaker adapters on Friday night last week and they arrived TODAY! All the way from PA! Holy smokes! All the way across the country in 3 days via USPS! That rocks! I spent some more time tonight doing the Ensolite, then fitted the adapters to the rear 6x9's and it's a perfect fit! This pic was before I mounted them so they are just sitting on top of the speaker. Even the tiny pre-drilled holes lined up perfectly. Now I need to wire up the new speakers and then I think I can start putting the back 1/2 of car together again.

If you need speaker adapters, I would HIGHLY recommend car-speaker-adapters.com. 🤘

Speaker adapters:
Picture not included in this copy
derickveliz2Central, MA · May 4, 2010#36
How deep are your 6.5 speakers? how thick are the adapters? It's probably that you may end up putting a spacer to clear the magnet and the glass of your window.
HerbicidalThread starterRoseville, CA - USA. · May 4, 2010#37
Originally Posted by derickveliz2 ↑
How deep are your 6.5 speakers? how thick are the adapters? It's probably that you may end up putting a spacer to clear the magnet and the glass of your window.
I just checked SonicElectronix and they say: Top mount depth is 3". This is measured from the bottom of the speaker magnet to the bottom of the mounting holes on the rim. The adapters are pretty slim, perhaps 1/4", maybe a little thicker. The speakers mounted in the adapters fit fine in the rear deck, no clearance issues that I can see. I bought the adapters so I could reuse the stock mounting holes in the rear deck without drilling new ones. To that end, it's a perfect fit!
derickveliz2Central, MA · May 4, 2010#38
Originally Posted by Herbicidal ↑
Top mount depth is 3". This is measured from the bottom of the speaker magnet to the bottom of the mounting holes on the rim. The adapters are pretty slim, perhaps 1/4", maybe a little thicker.
It's hard to tell, but you'll find out once you fit the 6.5 speaker into the front doors and lower your windows.

D.
HerbicidalThread starterRoseville, CA - USA. · May 4, 2010#39
Originally Posted by derickveliz2 ↑
It's hard to tell, but you'll find out once you fit the 6.5 speaker into the front doors and lower your windows.

D.
Ohhhh! These are for the rear deck, not the doors. I'm not to the doors yet. 😉
derickveliz2Central, MA · May 4, 2010#40
But on this picture you show to the right the 6.5 speakers and they go in the doors, is that right? if so you may need a spacer.

Picture not included in this copy
HerbicidalThread starterRoseville, CA - USA. · May 4, 2010#41
My bad, I misunderstood which speakers you were referring to. 😳 The ones on the right in that picture are the Kickers. According to Sonic, the Top Mount Depth is: 1 15/16's inches. Just a click short of 2 inches deep. These are used in "shallow mount installations", according to Sonic. Maybe I'll be OK? 🤷
derickveliz2Central, MA · May 4, 2010#42
Originally Posted by Herbicidal ↑
The ones on the right in that picture are the Kickers. According to Sonic, the Top Mount Depth is: 1 15/16's inches. Just a click short of 2 inches deep. These are used in "shallow mount installations", according to Sonic. Maybe I'll be OK? 🤷
They may be OK, I had the window control handy and plug it into it's connector to move the window up and down when I had the door naked, to test fit the speakers. It's good also to double check if the speakers wires don't get stuck with the glass too. But you won't know until you get to the doors.

Keep it up!

👍 Nice speakers by the way! 👍


.
HerbicidalThread starterRoseville, CA - USA. · May 7, 2010#43
Put some more time into the car tonight. Finished installing the rear speakers and actually put the entire trunk, rear deck and 'C' pillars back in, plus some plastic body panels that go over the rear wheel wells. The back seat is still out as I have some more deadening to do underneath and in front of the back seat. The rear speakers sound great! But I'm still toying with getting an amp before the backseat goes in. Before I get too much further I may buy some higher quality speaker wire and pre-run it before I cover everything up again. That will make it pretty much plug-and-play without having to remove a bunch of plastic panels again.

Deadened the license plate and inside the frame with scraps of RAAMmat and Ensolite. Don't throw your scraps away!
Picture not included in this copy

Put some extra Ensolite on the back of the plate where it may touch the car during EXTREME base. 😁
Picture not included in this copy

Reassabled the trunk area after installing the rear speakers. The new ones sound great!
Picture not included in this copy
HerbicidalThread starterRoseville, CA - USA. · May 7, 2010#44
I decided to get an amp, an amp wiring kit and a line output converter. Since I'm already 'into' the car, I might as well do it right!

Amp: Eclipse EA4200, free shipping, no sales tax (already shipped) for $129.99 from Crutchfield. Sonic Electronix wanted $209.99 and it's out of stock and backordered on their site.
Picture not included in this copy

Amp wiring kit: Earthquake Sound AK-3000, free shipping (already shipped), paid CA sales tax from Sonic for $29.99.
Picture not included in this copy

Line output converter: PAC SOEM-4, free shipping (already shipped), paid CA sales tax from Sonic. Listed at $32.99 but had a make offer button. I clicked it and submitted an offer of $25. It countered with $26 and I bought it! That savings more than covered my CA sales tax. 👍

Picture not included in this copy
derickveliz2Central, MA · May 8, 2010#45
Originally Posted by Herbicidal ↑
Amp: Eclipse EA4200, free shipping, no sales tax (already shipped) for $129.99 from Crutchfield. Sonic Electronix wanted $209.99 and it's out of stock and backordered on their site.

Amp wiring kit: Earthquake Sound AK-3000, free shipping (already shipped), paid CA sales tax from Sonic for $29.99.


Line output converter: PAC SOEM-4, free shipping (already shipped), paid CA sales tax from Sonic. Listed at $32.99 but had a make offer button. I clicked it and submitted an offer of $25. It countered with $26 and I bought it! That savings more than covered my CA sales tax. 👍
Some thing tells me that WE ALL LOVE FREE SHIPPING!
🙇

,
HerbicidalThread starterRoseville, CA - USA. · May 8, 2010#46
Oh yeah! I'm sure we're paying for it somewhere, but it looks good to see "free" where usually you see a big number!

Speaking of big numbers, I randomly checked the price of the Kicker speakers I bought for $109.99 at Sonic Electronix and they are now $199.95!!! 😲 What the heck happened to the price!!! 🤷 I would not have bought them for $199! I guess I got real lucky on that one. 🙄 Kind of the same thing price-wise with the Eclipse amp I bought today, Sonic was like $80 MORE than Crutchfield! That's just crazy!
HerbicidalThread starterRoseville, CA - USA. · May 11, 2010#47
The line output converter and the amp wiring kit arrived yesterday. The amp should arrive tomorrow. I've been chipping away at laying down the Ensolite on top of the RAAMmat the over the last several nights. I just about have it done up to the existing sound deadening on the floor of the passenger compartment. Once that is done, I'm turning my attention to the doors, front speakers, amp, etc. I'm leaving the rear seat out until I can run the speaker wires from the amp to the rear speakers since I have pretty good access on the passenger side. Since the jack is under the drivers seat, I think I will mount the amp under the passenger seat. By the way, the Alpines in the rear sound great even with only the power from the stock HU! I can hardly wait to wire up the fronts and the amp! 👍

Here's two pictures of my progress in the back seat area:

Passenger floor area, drivers side. I still need to lay some Ensolite on top of this small section of RAAMmat to finish up the rear seat area. Maybe another 15 minutes worth of work.
Picture not included in this copy

Passenger floor area, passenger side. I have layed the Ensolite on top of the RAAMmat up to the existing sound deadening material on the floor.
Picture not included in this copy
HerbicidalThread starterRoseville, CA - USA. · May 12, 2010#48
The Eclipse amp arrives today! Knowing that I need to remove at least the passenger seat, I searched YarisWorld and found the size of the socket I needed for those seat bolts. It's a Torx or Star socket, size: E10. Thanks to the person that posted that size up somewhere on here. 👍 I picked one up from Autozone yesterday. Once the amp arrives, I think I have everything to complete the audio upgrade portion of the install. I do need to pick up some stiff screen or some other material to lay over the rather large opening in the door panels so I can deaden both "walls" of the doors, then seal 'em up with Ensolite. Now the only other thing I need is time. Where the heck can I get that?!? 🙄
HerbicidalThread starterRoseville, CA - USA. · May 17, 2010#49
I was finally able to dedicate some time this past weekend to work on my car. This time it was pretty much all about the sound system upgrade portion. I pulled the stock radio out and with a radio wiring diagram, cut into the wiring harness and connected up the line output converter. Then I ran the power, ground, remote start wire and the RCA’s from the line output converter to the amp. I also ran the power lead for the amp through the firewall and up to the battery via a 60amp fuse block (no picture yet). Found a good ground to a bolt used for the parking brake lever, connected up the RCA’s from the line output converter, along with the remote start wire to the amp. Ran new speaker wires to the rear speakers and up to the amp. Powered on the radio and it all works! Nothing shorted, fried or otherwise crapped out. I’m working on mounting the amp and making all the wires running to it neat and tidy. Now I can start putting most of the interior back together. I still need to run speaker wires for the fronts and install them. When I get to that point, I’ll deaden the front doors too. Here’s some pics from my efforts over the weekend.


Passenger front seat and radio removed. Now to find a way to get the power lead for the amp through the firewall.
Picture not included in this copy

Man, it was a pain trying to find an access point through the firewall without drilling a hole! The passenger side floor has an A/C vent hose running through a rubber grommet. I used this as my access point through the firewall.
Picture not included in this copy

I drilled a hole in it and then angle cut the wire and put a little grease on it to help get it through the hole. Very snug and does not impact the vent tube nor does it touch bare metal.
Picture not included in this copy

This works great from my purposes.
Picture not included in this copy

Close up of the power lead inserted into a hole in the A/C vent grommet.
Picture not included in this copy

Sorry for the dark photo (the flash was blocked by something in the engine compartment), but this is the power lead coming out from the rubber grommet next to the A/C vent line in front of the firewall. I then routed up some other pre-existing lines and zipped tied the power line to them for a nice clean install.
Picture not included in this copy

I removed the access panel directly below the steering wheel and behind it is a panel parallel to the floor that I mounted the line output converter to. Works great and everything is hidden.
Picture not included in this copy

Here's the line output converter mounted (test fit) onto a panel that goes up above the foot pedals and behind the panel below the steering wheel. It is close to the back of the radio, about 24 inches away.
Picture not included in this copy

Line output converter mounted to panel above drivers feet (you can just barely see the top of it, some wires - blue and yellow - are sticking out to the right).
Picture not included in this copy

Test of the: (Radio and wires not connected in this picture) line output converter, and all the wires run for the amp and rear speakers. Yeaaa! It works! I still need to run the speaker wires for the fronts. Now I need to put it all together the right way.
Picture not included in this copy
derickveliz2Central, MA · May 17, 2010#50
Good progress makes me feel like I should make more time to work on mine!

I did find a grommet up high almost to the end of the firewall, very hard to access though, but keeps my power wires far right from all audio wires; Just in case,... don't let the RCA wires run near or parallel with the power wires for the amp, try to keep them as far as possible, if you have to... cross them in a 90 degree to prevent engine noise.

👍

Very nice, looking good! I'm still so far away from turning it on for testing.. )o: