Thanks for the tip! I put enough of the car back together last night so I could drive it to work today. The rear speakers are the only ones connected and they sound great! No engine noise transmitted via the wires. Now I need to add some more sound deadening to the rear wheel wells and under the rear seat before I put it back. Then I can shift my focus to the front doors, such as installing the new speakers, speaker wire (it's going to be fun getting it from the doors to inside the car), tweeters and deadening. Woohoo! 🙂
2008 Yaris sedan ‘S’ sound deadening project.
155 posts · 121,707 views · page 2 of 4
Replies continued
I almost have the entire car back together again. I was at Lowes yesterday and picked up some scrap carpet padding that is 1/2" thick. I stuffed it into some open cavities in the 'C' pillars (already sound deadened on the actual metal surface) and put some more under the rear seat as I have a resonator for the exhaust almost exactly under the seat. Plus there is a ton of room under the seat so why not add more (cheap) sound deadening while I'm in there? Somehow I lost a single bolt for the rear seat so I was not able to complete getting it all back together. I'll stop by the dealership on the way home and get what I need. Then I'm on to the doors and installing the front speakers along with the sound deadening. I need my front speakers! I'm looking forward to this next "stage" of my project. Doors, Doors, Doors!
I started with the rear doors, they are much easier than the front doors, I still have to do the pilot's door! and replace left speaker.
Sounds like you are almost there! awesome!
D.
.
Sounds like you are almost there! awesome!
D.
.
I think I'm going to start with the fronts as I really want to hear my new speakers! Since I'm doing only about 1/4 of the sound deadening you are doing, it figures I should be done much sooner! 😁 After the doors, and if I have leftover Ensolite, then I'm going to add it to the trunk area, right now it's just covered in RAAMmat.Originally Posted by derickveliz2 ↑I started with the rear doors, they are much easier than the front doors, I still have to do the pilot's door! and replace left speaker.
Sounds like you are almost there! awesome!
D.
.
I'm curious to see how your speakers go with the speaker adapters you got, since I'm going to use the 6.5 that goes in the door as a mid-bass I'm going back in there to beef things up and may replace the OEM adapter for one like yours and probably have to use a spacer.
good job!
good job!
Thanks! I'll post up some pics and comments when I get there.
I have completed what I'm calling stage 1. The car is completely back together but only with sound to the rear speakers. I have deadened everything from the front of the base of the rear seat to the trunk and everything in-between. The noise reduction based upon the sound level of my exhaust is quite dramatic! I still hear the exhaust, but it is a pleasant, underlying, background sort of sound. 👍 Having conversations in the car is much easier, I'm hearing instruments in the music that I have not heard before. Probably due to both the upgrade in speakers and the sound deadening. Now I can hear outside noise coming through the doors and little shifting sounds up on the headliner and I think from the back left and right corners of the car. The exhaust now exits in the center so I think that's why I can kind of hear it from both sides. At the moment, I did not put down any Ensolite in the trunk, it's just RAAMmat. If I have any Ensolite leftover once I'm done with the doors, I'm going to do the trunk.
I'm VERY happy with the results so far and I look forward to doing the doors. I should be able to start on them this weekend!
Oh yeah, after ordering a new bolt for the rear seat (yes, had to order it) I found the missing one stuck to a piece of RAAMmat in the car! Sheesh! That's the way it goes sometimes. 🙄
On to stage 2 - doors and front speakers!!!
I'm VERY happy with the results so far and I look forward to doing the doors. I should be able to start on them this weekend!
Oh yeah, after ordering a new bolt for the rear seat (yes, had to order it) I found the missing one stuck to a piece of RAAMmat in the car! Sheesh! That's the way it goes sometimes. 🙄
On to stage 2 - doors and front speakers!!!
This past weekend I was finally able to tackle the drivers side door. Woohoo! This door is now 'dead'! Not a rattle, squeak or noise out of it when it's shut. Just a nice solid - thud. My Father-in-laws Lexus has nothing on my door! 😁 With all the sound deadening, I've basically made the door a speaker box. I'm quite anxious to hear how it will sound. I made sure not to block the drain holes at the very bottom, in-side edge of the door. Also, the door panel had some hard foam door stiffeners that I was able to trim very easily by taking a hack saw blade out of the hack saw and cut through them by holding the blade in my hand. In the end, I had to totally remove the largest foam piece as it used to fit through an opening in the door, but I blocked the opening with sound deadening material.
Here's a photo montage of what I did for just the one door. Now to repeat on the passenger side and then the rear doors. It is alot of effort, but I'm already "hearing" the difference. The car is noticeably more 'solid' and quiet.
Door panel off. My work is cut out for me.
Picture not included in this copy
Drilling out the rivets that held in the factory door speaker.
Picture not included in this copy
Old speaker removed. You can just see the rubber boot where the wiring harness goes through the door.
Picture not included in this copy
The dreaded rubber boot that I needed to get the new speaker wire through.
Picture not included in this copy
Coat hanger with speaker wire taped to it. My first effort failed. I redid the taping job and put some Vasoline on the wire and that time it worked!
Picture not included in this copy
New speaker wire routed through the rubber door boot. Yeah, that was fun!
Picture not included in this copy
Close up of RAAMmat inside the door shell. With the large openings, I was able to deaden 95% of the inside of the door.
Picture not included in this copy
RAAMmat fully applied within the door shell.
Picture not included in this copy
Plastic panels secured with small sheet metal screws to cover the access holes.
Picture not included in this copy
Close up of the speaker opening with the RAAMmat applied inside. That's the bottom edge of the window. Just testing to make sure everything worked correctly after applying the deadening material.
Picture not included in this copy
Speaker opening with RAAMmat behind the Ensolite. A small square of it sits behind the speaker, per the instructions on RAAMaudio.com
Picture not included in this copy
RAAMmat applied on all available surfaces. Crossover for the Kicker speaker and tweeter is in the lower left with the cover off. The new speaker is mounted in the door using speaker adapters. Perfect fit!
Picture not included in this copy
This is one dead door! The final layer is sound deadening Ensolite foam. I made sure to stay back about 1" from all the edges so that the door panel would fit back on correctly.
Picture not included in this copy
Kicker tweeter (back view) installed in small plastic window panel. Had to use a 2" hole saw to cut the hole in the panel.
Picture not included in this copy
Kicker tweeter (front view) installed in small plastic window panel.
Picture not included in this copy
Door panel back on and the Kicker tweeter mounted in mirror cover panel. There is a beveled housing that allows the tweeter to be mounted at an angle. I may need to adjust the angle again when dialing everything in.
Picture not included in this copy
On to the passenger door! Once that's done, I can connect up my front speakers and finally have all the speakers working again. 👍
Here's a photo montage of what I did for just the one door. Now to repeat on the passenger side and then the rear doors. It is alot of effort, but I'm already "hearing" the difference. The car is noticeably more 'solid' and quiet.
Door panel off. My work is cut out for me.
Picture not included in this copy
Drilling out the rivets that held in the factory door speaker.
Picture not included in this copy
Old speaker removed. You can just see the rubber boot where the wiring harness goes through the door.
Picture not included in this copy
The dreaded rubber boot that I needed to get the new speaker wire through.
Picture not included in this copy
Coat hanger with speaker wire taped to it. My first effort failed. I redid the taping job and put some Vasoline on the wire and that time it worked!
Picture not included in this copy
New speaker wire routed through the rubber door boot. Yeah, that was fun!
Picture not included in this copy
Close up of RAAMmat inside the door shell. With the large openings, I was able to deaden 95% of the inside of the door.
Picture not included in this copy
RAAMmat fully applied within the door shell.
Picture not included in this copy
Plastic panels secured with small sheet metal screws to cover the access holes.
Picture not included in this copy
Close up of the speaker opening with the RAAMmat applied inside. That's the bottom edge of the window. Just testing to make sure everything worked correctly after applying the deadening material.
Picture not included in this copy
Speaker opening with RAAMmat behind the Ensolite. A small square of it sits behind the speaker, per the instructions on RAAMaudio.com
Picture not included in this copy
RAAMmat applied on all available surfaces. Crossover for the Kicker speaker and tweeter is in the lower left with the cover off. The new speaker is mounted in the door using speaker adapters. Perfect fit!
Picture not included in this copy
This is one dead door! The final layer is sound deadening Ensolite foam. I made sure to stay back about 1" from all the edges so that the door panel would fit back on correctly.
Picture not included in this copy
Kicker tweeter (back view) installed in small plastic window panel. Had to use a 2" hole saw to cut the hole in the panel.
Picture not included in this copy
Kicker tweeter (front view) installed in small plastic window panel.
Picture not included in this copy
Door panel back on and the Kicker tweeter mounted in mirror cover panel. There is a beveled housing that allows the tweeter to be mounted at an angle. I may need to adjust the angle again when dialing everything in.
Picture not included in this copy
On to the passenger door! Once that's done, I can connect up my front speakers and finally have all the speakers working again. 👍
Looks awesome! I can't wait to deaden my doors! Thanks for the pics.
Thanks DailyDriver and you're welcome! It is nice to see what needs to be done ahead of time. Derick's photos in his sound deadening thread helped me quite a bit too. 👍
Well I couldn't wait any longer! I HAD to hook up the front speakers to hear how they sound even though the front passenger door isn't deadened yet. After about 2 hours worth of work, I had the new speaker/tweeter/crossover (the crossover location is temporary, but works for now) installed and hooked up to the amp. WOW!!! I LOVE it! The highs are so crisp it feels like you could cut paper! However, that front passenger door is begging for mercy! 😲 There are some rattles (of course) and noises that will be killed once I deaden that door. The drivers door is very tight and the mid's just punch through! This clearly demonstrated the value of sound deadening. With a 3-day weekend coming up, I should be able knock off that passenger door and maybe even the rear doors!
On another note (no pun intended) this morning on the drive into work I had a guy in a Toyota T-100 catch up to me on the inside lane and as he pulled slightly ahead I could see a thumbs up coming from him. Did he hear my music too? Nah....but it made me 🙂.
Well I couldn't wait any longer! I HAD to hook up the front speakers to hear how they sound even though the front passenger door isn't deadened yet. After about 2 hours worth of work, I had the new speaker/tweeter/crossover (the crossover location is temporary, but works for now) installed and hooked up to the amp. WOW!!! I LOVE it! The highs are so crisp it feels like you could cut paper! However, that front passenger door is begging for mercy! 😲 There are some rattles (of course) and noises that will be killed once I deaden that door. The drivers door is very tight and the mid's just punch through! This clearly demonstrated the value of sound deadening. With a 3-day weekend coming up, I should be able knock off that passenger door and maybe even the rear doors!
On another note (no pun intended) this morning on the drive into work I had a guy in a Toyota T-100 catch up to me on the inside lane and as he pulled slightly ahead I could see a thumbs up coming from him. Did he hear my music too? Nah....but it made me 🙂.
I also pulled new wiring through that boot in the front door. My wire puller didnt want to go through until i dipped it into a tube of lithium grease. Then it went no problem.👍
Yeah, trying to pull it through the rubber boot was tough with no lube. OK, not going there...Originally Posted by centrysis ↑I also pulled new wiring through that boot in the front door. My wire puller didnt want to go through until i dipped it into a tube of lithium grease. Then it went no problem.👍
On another note, I completed the deadening on the front passenger door and the right rear passenger door, just one more to go!!!! 👍 Pics are still on the camera.
And ya'll may have seen my post about needing another amp for a subwoofer. I'm this close to pulling the trigger on a mono Eclipse amp, Alpine Type R 10" sub and a box for the sub. THAT should round out the system nicely! 👍
Make sure that the amp is pushing no less than 500 watts. My Alpine M450 is underpowering my Type R (only 400 watts). What kind of box are you getting? If you want a sealed box, I'll sell you mine as I want a vented/ported box now.
Be careful with the vented enclosure. I've seen a lot of people kill woofers with less power on a vented application. With with all due respect to taln and his love for vented enclosures, he is a small minority of people who can control themselves with the voltage potentiometer.
Really? hmmm, so if the Type R (10") is rated at 500 watts, and the ported box that I'm looking at is the max volume rating for it, would that cause any problems?
From my other thread about asking whether I needed another amp to power a woofer, here is what I'm looking at now based upon recommendations by Alien Mantis. I would run the Eclipse XA1200 from the pre-outs on my current Eclipse amp. He also suggested setting the amp for 2 ohms:
Eclipse XA1200600W Max, XA Series Class D Monoblock Car Amplifier (XA-1200) for $129 at Sonic.
Product Features:XA Series Class D Monoblock Car Amplifier with ICE Technology
RMS Power Rating:
4 ohms: 350 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Max power output: 600 watts
MOSFET switching power supply
ICEpower class D design
Wired remote bass level control included
LED power indicators
Bass Boost (0-8 dB at 50 Hz)
Bass boost frequency selection (32-64 Hz)
Mono channel operation
Protection temperature (90 C)
Heavy duty aluminum alloy heatsink
RCA level inputs
Screw terminals
Variable low-pass filter (40-200 Hz, Linkwitz Riley 18 dB/octave)
Subsonic Filter (18 dB at 20 Hz)
CEA-2006 compliant amplifier
Frequency response: 20-20,000 Hz
Input sensitivity: 1.2V-8V
Damping Factor: 90
Dimensions: 10-1/4"L x 10-1/8"W x 2-3/8"H
4-gauge power and ground wiring is required for installation.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Alpine SWR-1042D (TYPE R)10" Dual 4 ohm Type-R Subwoofer for $99:
Picture not included in this copy
Sonic Sub Box: 1SV10 (BLACK CARPET)Single 10" Vented MDF Enclosure for $29.99:
Picture not included in this copy
Eclipse XA1200600W Max, XA Series Class D Monoblock Car Amplifier (XA-1200) for $129 at Sonic.
Product Features:XA Series Class D Monoblock Car Amplifier with ICE Technology
RMS Power Rating:
4 ohms: 350 watts x 1 chan.
2 ohms: 500 watts x 1 chan.
Max power output: 600 watts
MOSFET switching power supply
ICEpower class D design
Wired remote bass level control included
LED power indicators
Bass Boost (0-8 dB at 50 Hz)
Bass boost frequency selection (32-64 Hz)
Mono channel operation
Protection temperature (90 C)
Heavy duty aluminum alloy heatsink
RCA level inputs
Screw terminals
Variable low-pass filter (40-200 Hz, Linkwitz Riley 18 dB/octave)
Subsonic Filter (18 dB at 20 Hz)
CEA-2006 compliant amplifier
Frequency response: 20-20,000 Hz
Input sensitivity: 1.2V-8V
Damping Factor: 90
Dimensions: 10-1/4"L x 10-1/8"W x 2-3/8"H
4-gauge power and ground wiring is required for installation.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Alpine SWR-1042D (TYPE R)10" Dual 4 ohm Type-R Subwoofer for $99:
Picture not included in this copy
Sonic Sub Box: 1SV10 (BLACK CARPET)Single 10" Vented MDF Enclosure for $29.99:
Picture not included in this copy
Uh, I'll be driving the Type R 10" 1042D with 300W at, I believe, 2ohms, from the Alpine PDX-5, in a sealed 0.7cubic box. While I don't worry about SPL, could this hurt the sub?
probably not, as long as you keep with the Alpine reccomendations it should be fine... Companies make recommendations so that customers won't be blowing subs left and right....Originally Posted by Kaotic Lazagna ↑Really? hmmm, so if the Type R (10") is rated at 500 watts, and the ported box that I'm looking at is the max volume rating for it, would that cause any problems?
If you stray from those recommendations however you may start to run into mechanical limitations of the moving parts... if you start hearing a slapping noise (like metal on metal or a hammer) at all you need to turn it down ASAP. i'm not sure if you'd head the former slap the back plate first, or if the spider would start to tear first.
be nice to the sub, listen for distortion, distortion is your best warning that your sub is running out of steam.
I have reached another milestone!!! All four doors are now sound deadened!!!! Woohoo!!! 👍 Pic's are still on the camera, I'll download and post them up later. I used up all my RAAMmat, but I have a ton of Ensolite leftover, so next I will lay the foam on top of the RAAMmat in the trunk area in preparation for whatever subwoofer I end up with. Waay back at the begining, I only did the RAAMmat in the trunk, not knowing how much Ensolite I was going to use for the doors and under the rear seat. I ended up buying more Ensolite, so now I have PLENTY to do the trunk.
Looking good!
It's nice to see a project like this grow and been done!
D.
It's nice to see a project like this grow and been done!
D.
Thanks Derick! Well, almost done. 🙄 Still need to do the trunk area with the Ensolite and decide on the amp and subwoofer. But I'm darn close! 😁Originally Posted by derickveliz2 ↑Looking good!
It's nice to see a project like this grow and been done!
D.
After completing the front passenger door, I was starting to run out of RAAMmat. I had only six 15" squares left, so I divided them up amongst the rear doors. I wasn't able to cover them as fully as the front doors, but since they don't have speakers, I wasn't as concerned. I do have plenty of the sound deadening Ensolite foam, so I put that on as thick as I dared. Too thick and the door panels would not fit back on correctly. All four doors are now "dead". You can rap on the outside and it's just a 'thud' vs a hollow sound. Since I have quite a bit of the Ensolite sound deadening foam, I'm going to go back to the trunk area and line it with the Ensolite. Right now it's just covered in the RAAMmat. Then I'll need to try the decibel meter again and see what it reads. To my ears, it is quieter inside and not nearly as much road and exhaust noise makes it's way into the cabin. The stereo sounds better than ever with the new front Kicker speakers and tweeters, plus the new Alpine Type R's in the rear. Now to decide on another amp and subwoofer.
Here's the rest of the pictures from this weekends efforts:
Getting started on the left rear passenger door.
Picture not included in this copy
Close up of the RAAMmat on the inside of the door panel.
Picture not included in this copy
Left rear passenger door. RAAMmat stuck to the inside of the door.
Picture not included in this copy
Plastic signs trimmed to fit and covering up the large holes in the door.
Picture not included in this copy
Left rear passenger door with RAAMmat in various places. I was just about out of it and to be selective on where I placed it.
Picture not included in this copy
Left rear passenger is done!
Picture not included in this copy
I added some Ensolite to the inside of the door panel for good measure. It's the black material.
Picture not included in this copy
Starting on the right front passenger door. The plastic weather piece is already stripped off and I've placed RAAMmat inside the door on the inner panel.
Picture not included in this copy
I had to buy some more plastic signs to fill the rather large holes in the door before I could lay down the RAAMmat on this side of the door panel. Figuring out what size they needed to be.
Picture not included in this copy
Signs all in place held by small sheet metal screws. Now I can lay the RAAMmat onto of everything and seal them up.
Picture not included in this copy
RAAMmat covering everything! Next is the Ensolite.
Picture not included in this copy
Right front passenger door is done! Tweeter mounted in the plastic panel near the mirror. New Kicker speaker mounted in the door along with the crossover.
Picture not included in this copy
Getting started on the right rear passenger door.
Picture not included in this copy
More inexpensive plastic signs to cover the holes with. Then I put the RAAMmat and Ensolite in layers on the door.
Picture not included in this copy
Right rear passenger door is done!
Picture not included in this copy
Here's the rest of the pictures from this weekends efforts:
Getting started on the left rear passenger door.
Picture not included in this copy
Close up of the RAAMmat on the inside of the door panel.
Picture not included in this copy
Left rear passenger door. RAAMmat stuck to the inside of the door.
Picture not included in this copy
Plastic signs trimmed to fit and covering up the large holes in the door.
Picture not included in this copy
Left rear passenger door with RAAMmat in various places. I was just about out of it and to be selective on where I placed it.
Picture not included in this copy
Left rear passenger is done!
Picture not included in this copy
I added some Ensolite to the inside of the door panel for good measure. It's the black material.
Picture not included in this copy
Starting on the right front passenger door. The plastic weather piece is already stripped off and I've placed RAAMmat inside the door on the inner panel.
Picture not included in this copy
I had to buy some more plastic signs to fill the rather large holes in the door before I could lay down the RAAMmat on this side of the door panel. Figuring out what size they needed to be.
Picture not included in this copy
Signs all in place held by small sheet metal screws. Now I can lay the RAAMmat onto of everything and seal them up.
Picture not included in this copy
RAAMmat covering everything! Next is the Ensolite.
Picture not included in this copy
Right front passenger door is done! Tweeter mounted in the plastic panel near the mirror. New Kicker speaker mounted in the door along with the crossover.
Picture not included in this copy
Getting started on the right rear passenger door.
Picture not included in this copy
More inexpensive plastic signs to cover the holes with. Then I put the RAAMmat and Ensolite in layers on the door.
Picture not included in this copy
Right rear passenger door is done!
Picture not included in this copy
As mentioned in my 'do I need another amp?' thread, I have ordered the Eclipse mono channel amp, Alpine Type R 10" subwoofer and an enclosure. Now I need to pick up some 4 gauge wire (power and ground), another fuse block, firewall grommet and a few other odds and ends. Now I'm motivated to get the trunk lined with Ensolite to provide a nice snug home for the new subwoofer. 🤘 I'm so glad to be done with the doors!!!!
OK, I thought the 'Danger High Voltage' signs in the right front passenger door was funny, even if they will never be seen again! Even my daughter laughed! 🤣
Did I mention I'm glad to be done with the doors??? 😛
OK, I thought the 'Danger High Voltage' signs in the right front passenger door was funny, even if they will never be seen again! Even my daughter laughed! 🤣
Did I mention I'm glad to be done with the doors??? 😛
Something I really like about the doors after deadening is (and just for key-less entry) that when you lock / unlock your car with the remote, you can barely hear the noise of the system, standing next to your car...Originally Posted by Herbicidal ↑Did I mention I'm glad to be done with the doors??? 😛
give it a try!.
👏
👍
Yup! You are right. Just a little 'snick, snick'.Originally Posted by derickveliz2 ↑Something I really like about the doors after deadening is (and just for key-less entry) that when you lock / unlock your car with the remote, you can barely hear the noise of the system, standing next to your car...
give it a try!.
👏
👍
My parts arrived yesterday! Ohhhh yaaaa! I stopped by Fry's Electronics on my way home from work and picked up an amp install kit that has 4 gauge wires for power and ground, speaker wire, remote turn on wire for the amp, plus all the little stuff that comes with the kit. I also spent $20 and bought a Monster 3-way slim line distribution block (will accept 4 gauge wire) that connects to the battery. I'll use two of the three openings for the power wires to both amps. This leaves me one for whatever floats my boat down the road. I still need to pick up a rubber grommet for the firewall as this time I think I will drill a hole next to the A/C vent drain plug hole that I used for the last power wire. Hopefully this weekend I can start running the wires, etc.
By the way, with the subwoofer enclosure, is there a "right way" to position it?
Originally Posted by Herbicidal ↑By the way, with the subwoofer enclosure, is there a "right way" to position it?
usually facing it toward the rear of the car will give you the most bass.
Thanks much! I'll try it that way first. 👍Originally Posted by talnlnky ↑usually facing it toward the rear of the car will give you the most bass.
In my hatchback, facing towards the rear is the best.
So I guess that is bass-ackwards! 😁 Sorry, that was pretty bad. 🙄
Still gonna do that dB reading after your speakers and sub are broken in? 😁
Hi Kaotic, I'm sure herb can do that too, but the dB reading was to measure the noise level in the cabin before and after deadening with out music playing.Originally Posted by Kaotic Lazagna ↑Still gonna do that dB reading after your speakers and sub are broken in? 😁
.👍
D.
hahaha, I know. It's one of those shits-and-giggles things. I just want to see how loud his system can get 😛Originally Posted by derickveliz2 ↑Hi Kaotic, I'm sure herb can do that too, but the dB reading was to measure the noise level in the cabin before and after deadening with out music playing.
.👍
D.
Sure, I'll do it both ways! I'll need some earplugs before doing the stereo check. 😁 Still gotta tune it! Hopefully tomorrow I'll have some time to play around with amp settings.
In case you haven't been following my thread about whether I need another amp to power a subwoofer, here's an update on what I've done since the new equipment arrived from Sonic Electronics. For others, this will be a repeat of the info, sorry about that. 😳 Just trying to keep some continuity. By the way, I ended up returning that Monster slim-line power block. It wasn't slim enough. With it on the positive battery post, the battery cable would not fit on correctly, so I took it back. I was able to attach the power wire for the second amp to an existing accessories 'tab' on the cable.Originally Posted by Herbicidal ↑My parts arrived yesterday! Ohhhh yaaaa! I stopped by Fry's Electronics on my way home from work and picked up an amp install kit that has 4 gauge wires for power and ground, speaker wire, remote turn on wire for the amp, plus all the little stuff that comes with the kit. I also spent $20 and bought a Monster 3-way slim line distribution block (will accept 4 gauge wire) that connects to the battery. I'll use two of the three openings for the power wires to both amps. This leaves me one for whatever floats my boat down the road. I still need to pick up a rubber grommet for the firewall as this time I think I will drill a hole next to the A/C vent drain plug hole that I used for the last power wire. Hopefully this weekend I can start running the wires, etc.
Here's my most recent set of pictures. As I mentioned before, the install went pretty smooth, just time consuming to do a ‘clean’ install. I used an air powered cut off wheel to remove the jack bracket under the driver’s seat and the jack does fit snugly in the spare tire compartment. I had to place a piece of 2x4 under each amp to get a level mounting spot because of a funky space between some horizontal body supports. This made it easier to connect up the wiring. I figure this allows the air to flow partially underneath and will help with the overall cooling of the amp. I’m still experimenting with placement of the subwoofer box in the trunk. Laying it flat with the sub pointing to the rear of the car takes up the most room, but standing it up and rotating it 90 degrees gives me the most space in the trunk and puts the weight closer to being over the rear axle. Anyway, I’m still playing with the positioning for sound and space maximization of the sub.
Without further ado:
Eclipse XA1200 mono channel amp.
Picture not included in this copy
Alpine Type R 10" sub.
Picture not included in this copy
Alpine Type R 10" sub, top view.
Picture not included in this copy
Alpine Type R 10" sub, connectors. I used the jumpers to set it up for 2 ohms.
Picture not included in this copy
10" vented sub enclosure from Sonic Electronix.
Picture not included in this copy
Alpine Type R 10" sub-in-the-box.
Picture not included in this copy
Preparing for surgery. That car jack mounting bracket has to go!
Picture not included in this copy
Where the bracket for mounting the car jack was, under the drivers seat. Needed to make room for the other amp.
Picture not included in this copy
The blue wire is 4 gauge for power to the subwoofer amp. The black tube is the A/C breather that vents to the outside of the firewall.
Picture not included in this copy
4 gauge power wires through the firewall passenger foot well red for the speaker amp, blue for the subwoofer amp.
Picture not included in this copy
Eclipse mono channel subwoofer amp on the left, Eclipse 4 channel amp for the speakers on the right.
Picture not included in this copy
Alpine Type R 10" sub in a box. I'm still trying different locations and positions so the wiring isn't finalized yet.
Picture not included in this copy
And my experience of "tuning" the amps, also from my 'do I need another amp...' thread:
I finally was able to spend about 2 hours yesterday to tune my amps. Crawling around in the back seat with Alien Mantis's instructions in one hand and a small screwdriver in the other, moving the front seats all the way forward so I could get to the adjustment screws, making adjustments, moving the seats back to the regular positions so I could sit in the drivers seat and listen, then repeat the process all over again about six more times. When I first took a look at the adjustment screws, everything on both amps was basically turned "off". While installing them, I didn't even look at the adjustment screws because I really didn't understand them. Since last Saturday, essentially I have not been using the subwoofer amp, and for another two weeks at least, the speaker amp! I was so focused on the install and keeping it all neat and tidy I just didn't even pay any attention to what position those adjustment screws where in! What a dumba$$! 🙄
HOLY FREAK'IN MOTHER OF BASS BATMAN!!!
I can't believe the difference! I still have a HUGE $hit eating grin plastered on my face this morning! AND I'm using the stock head unit! I can't imagine the sound getting better than this, let alone what a decent quality HU would do for me! WOW!!! Obviously I am very happy with the amps, speakers and subwoofer! Once I was done, I even vacuumed and washed my car. Ahhhhhhhh! 🙂 My 13 year old daughter was in the house and came out to the garage to find out what the heck was going on! 😁
LESSON: Make sure to TUNE YOUR AMP(s)!!! If you haven't done it yet, get out there and do it!!! Othewise you are just wasting your hard earned $$$'s!!!
🙇
I finally was able to spend about 2 hours yesterday to tune my amps. Crawling around in the back seat with Alien Mantis's instructions in one hand and a small screwdriver in the other, moving the front seats all the way forward so I could get to the adjustment screws, making adjustments, moving the seats back to the regular positions so I could sit in the drivers seat and listen, then repeat the process all over again about six more times. When I first took a look at the adjustment screws, everything on both amps was basically turned "off". While installing them, I didn't even look at the adjustment screws because I really didn't understand them. Since last Saturday, essentially I have not been using the subwoofer amp, and for another two weeks at least, the speaker amp! I was so focused on the install and keeping it all neat and tidy I just didn't even pay any attention to what position those adjustment screws where in! What a dumba$$! 🙄
HOLY FREAK'IN MOTHER OF BASS BATMAN!!!
I can't believe the difference! I still have a HUGE $hit eating grin plastered on my face this morning! AND I'm using the stock head unit! I can't imagine the sound getting better than this, let alone what a decent quality HU would do for me! WOW!!! Obviously I am very happy with the amps, speakers and subwoofer! Once I was done, I even vacuumed and washed my car. Ahhhhhhhh! 🙂 My 13 year old daughter was in the house and came out to the garage to find out what the heck was going on! 😁
LESSON: Make sure to TUNE YOUR AMP(s)!!! If you haven't done it yet, get out there and do it!!! Othewise you are just wasting your hard earned $$$'s!!!
🙇
The but of that woofer looks intimidating
Too bad we can't hear it / feel it.
D.
Too bad we can't hear it / feel it.
D.
So what was the "after" reading?? I can't find it anywhere 🆘Originally Posted by derickveliz2 ↑Hi Kaotic, I'm sure herb can do that too, but the dB reading was to measure the noise level in the cabin before and after deadening with out music playing.
.👍
D.
Sorry my friend! I have not made the time to get the "after" reading. Not your fault, it's all me! I was camping last weekend and I leave in a couple of days for another 4 night trip. I might not have it for a little while yet, sorry. 😳 But I have not forgotten!Originally Posted by Niels J ↑So what was the "after" reading?? I can't find it anywhere 🆘
OK, the wife wasn't home so I pulled into the garage, closed the door behind me and cranked up the tunes with the engine off and the windows up. The MAX my little hand-held db meter read was 97.7 db! That was all I could take! 😲 I wasn't detecting distortion, but I didn't want to 'blow' anything either. 🙄 With the same song playing at the same volume I stepped out of the car and closed the door and took another reading about 6 feet away at the side of the car: 77.3 db, basically a 20 db drop to the outside. I guess that's good? 🤷Originally Posted by Kaotic Lazagna ↑Nice. Just for shits and giggles, take a dB rating after you break in the speakers. hahaha.
Now the crazy part. I put the db meter in the backseat like I did way back when. I didn't tape it down, but set on a sweatshirt so it wouldn't slide around. Rolled up the windows, turned off the radio and nailed the gas. Now I digress for a moment, the car is not as quick as before with the RAAMmat layered all over the place (2 boxes worth), two amps, subwoofer box and subwoofer, plus slightly heavier new speakers front and rear. That's kind of a bummer, but that's the trade-off for a great sounding system. Oh well. I accelerated up to about 50 mph, then pulled over so I could read the db meter...86.3 db!!! This is actually louder than before! So you don't have to go looking, the original reading was 84.7! What the heck?!? The interior sounds quieter to me so I really don't understand why it's reading higher now. 🙁 Beats the Ensolite out of me! However, I don't think I would do anything different. Very strange. I'm open to anyone's guess!
I'd say its the meter. I've followed your work. I only put mat down on the back of my HB, and it was an improvement. Some of those meters aren't that reliable. Your ears are right. It is quieter.👏
That's awesome Herb. Although, I'm not sure how I would feel about the louder exhaust reading (I do want my exhaust louder tho, lol). I wonder how different my system (just a JVC HU and a Type R sub) will sound compared to yours. hehehe.
Hey Herb,
Maybe it's a guitar effect?
Or the meter it's bad?
It's true... you can hear/feel the difference, but it could be just another level/frequency of resonance inside the car that resonates different from the outside noise.
You have taken care of some of the resonance of the sheet metal panels of your car by applying Mat and Ensolite, now it's like a big speaker to the inside, what you may need now it's a "Noise Barrier" AKA Mass Loaded Vinyl (MLV).
Send me that meter and I'll give it a try in my car.
D.
Maybe it's a guitar effect?
Or the meter it's bad?
It's true... you can hear/feel the difference, but it could be just another level/frequency of resonance inside the car that resonates different from the outside noise.
You have taken care of some of the resonance of the sheet metal panels of your car by applying Mat and Ensolite, now it's like a big speaker to the inside, what you may need now it's a "Noise Barrier" AKA Mass Loaded Vinyl (MLV).
Send me that meter and I'll give it a try in my car.
D.
Thanks man. I decided I'm not going to waste a lot of thought processes on it. I'm VERY HAPPY with everything, so to heck with the reading. 😁Originally Posted by centrysis ↑I'd say its the meter. I've followed your work. I only put mat down on the back of my HB, and it was an improvement. Some of those meters aren't that reliable. Your ears are right. It is quieter.👏
We need to meet up again soon. I've never heard your system, it would be fun to do a comparison. 👍Originally Posted by Kaotic Lazagna ↑That's awesome Herb. Although, I'm not sure how I would feel about the louder exhaust reading (I do want my exhaust louder tho, lol). I wonder how different my system (just a JVC HU and a Type R sub) will sound compared to yours. hehehe.
I'm thinking your "Noise Barrier" suggestion is probably hitting the nail on head along with another level/frequency inside the car. Weird. Again, I'm not going to worry about it! If you really want to try the meter on your project, send me a PM with your mailing address info (home or work) and I'll send it to you. Just send it back when you're done.Originally Posted by derickveliz2 ↑Hey Herb,
Maybe it's a guitar effect?
Or the meter it's bad?
It's true... you can hear/feel the difference, but it could be just another level/frequency of resonance inside the car that resonates different from the outside noise.
You have taken care of some of the resonance of the sheet metal panels of your car by applying Mat and Ensolite, now it's like a big speaker to the inside, what you may need now it's a "Noise Barrier" AKA Mass Loaded Vinyl (MLV).
Send me that meter and I'll give it a try in my car.
D.
Thanks! I read through most, not all of the posts, and I feel better! So it's not just me! 😛 I got your PM (I was gone camping the last several days), do you still want me to send you my little digital meter based upon that link? Either way, it doesn't matter to me.Originally Posted by derickveliz2 ↑
.
Yeah, lets give it a try...
Yeah, lets give it a try...
I've got the perfect box. I'll wrap it up and try to stop by the Post Office tomorrow on my way home from work.
As part of my sound deadening project, I'm looking to add some CLD tiles to the roof..Anyone have tips/experience removing the roof liner? I'm a little nervous, as it seems more delicate than lifting up the carpet/trim pieces!
I believe that SQComp has done his headliner. He has a HUGE thread going on in this same forum section. I don't have the exact page, but I thought he did it about 2 months ago? I'm thinking about doing my roof too, but for now, I'm just enjoying my car!Originally Posted by gates_2 ↑As part of my sound deadening project, I'm looking to add some CLD tiles to the roof..Anyone have tips/experience removing the roof liner? I'm a little nervous, as it seems more delicate than lifting up the carpet/trim pieces!
Look in here
2007 Yaris S Sound Deadening
it's big and lots of information.
I'm going to apply at least 6 CLD tiles to the roof too. SOON!
I will post it here:
Link to a thread or page that is not in the archive
.👍
2007 Yaris S Sound Deadening
it's big and lots of information.
I'm going to apply at least 6 CLD tiles to the roof too. SOON!
I will post it here:
Link to a thread or page that is not in the archive
.👍