Yarisworld Archive

Big 3 Upgrade: Planning Stage (Input Encouraged)

145 posts · 40,685 views · page 1 of 3

The ArchitectOriginal postFL · Sep 1, 2009#1
I have big plans in the works for my electrical system and the big 3 is one of them and I want to do it right and well the first time so I'll take any and all worthwhile educated input. If you have your own pictures etc please feel free.

1/0 Gauge will be used.

----Alternator to Battery Positive
----Battery Negative to Chassis
----Battery Negative to Engine

I took a few nice images of the engine bay in multiple spots so you may mark and re-upload them for reference if you have suggestions for mounting locations etc.

And one direct question I have is about the metal tab/group coming off the + terminal of the battery (shown below). I want to have two tri-1/0 gauge battery terminals in the end, one on each post. Is there a way to eliminate that ugly group and incorporate it into the new battery terminal?

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy




Onto the engine bay pictures.....ITS DIRTY...i know

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Replies 144

1NZYaris1New Zealand · Sep 1, 2009#2
I did something similar a couple of months back ,
put a Bigger earth too Chassis
and an earth on the Alternator Bracket
results according to the scanguage where an instant inprovement in chargeing from 14.0 to.1 too 14.2 -.3 depending on rev's
and that is with the NST10% under drive pulley 👍
talnlnkySpokane, Wa · Sep 1, 2009#3
so some tips...

1: battery connector pick up something like this... http://stingerelectronics.com/produc...-1&ParentID=-1
if you look around you should be able to find one with the right amount of inputs that you need.

2:get your hands on a multimeter. set it to find resistance (amount of ohms... the horse shoe thing). Put one of the probes on the battery terminal, the other on various chassis points... take a ohm reading at each chassis point, and the point that has the lowest ohm rating is the one you want to go with. I believe you want to put the bat prob on the positive terminal, but I might be wrong.

3: don't replace any of the stock wires... just add the 1/0awg in addition to the stock... its a lot less work that way, and will actually be better, and in the future, if you sell the car it'll be easier to take you spendy 1/0awg out and use in your next car.
talnlnkySpokane, Wa · Sep 1, 2009#4
Originally Posted by 1NZYaris1 ↑
I did something similar a couple of months back ,
put a Bigger earth too Chassis
and an earth on the Alternator Bracket
results according to the scanguage where an instant inprovement in chargeing from 14.0 to.1 too 14.2 -.3 depending on rev's
and that is with the NST10% under drive pulley 👍
Sqcomp swears he gains 2mpg when he did his upgrade.... i have a hard time believing that, but if the stock ground is completely horrible, its possible.
The ArchitectThread starterFL · Sep 2, 2009#5
the "Earth" concept is one I've heard very little of, When he mentioned it I assumed it merely meant as ground. If I'm wrong feel free to elaborate.

Knu konceptz has some nice triple 1/0 terminals ill be picking up along with a few runs of 1/0
TamagoOff Grid · Sep 2, 2009#6
in non-us countries, EARTH is ground.
The ArchitectThread starterFL · Sep 2, 2009#7
ahhh i see, sorry for my ignorance lol
sqcompBack at home · Sep 4, 2009#8
I was at a mid 40's for MPG...after that big three...it went up to upper 42 to mid 43's.

I had NO changes in driving.

I had a post that showed what I did...lemme find the link
sqcompBack at home · Sep 9, 2009#9
Okay...after forgetting about this post for a few days...I KNOW I posted my little link somewhere on the big 3. It is GONE...

The big 3 cost me $13 to do. I found some old parts that the shop had "scrapped" and some old Lightning Audio compression fittings that were bought at pennies on the dollar when they bought the shop...

So, thank the Lord for Photobucket:

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
sqcompBack at home · Sep 9, 2009#10
...and yes, I will re-do the engine compartment grounds after I get home from Iraq. I need to make ready for IASCA...

Every little improvement will help. That includes techflexing and putting heat shrink around the terminations of the grounds. They look amateur now. I already purchased a nice little billet aluminum battery clamp thingy from Micro Image. I'm thinking some billet brass connectors for some kinetik batteries soon...

I can do much better than these grounds I have on there now, show-wise at least.

As was mentioned I did NOT remove stock grounds, I only added. Besides, the power flows on the path of least resistance.
The ArchitectThread starterFL · Sep 9, 2009#11
the alt ground and chassis ground were good representations but I couldnt make out where the engine ground was, any chance of better pics or something for clarification?
sqcompBack at home · Sep 10, 2009#12
by the battery and on the other side off the alternator bracket. The engine ground was on the underside of the car looking up. I can't get you new pictures just at this moment. I'm sort of stuck in Iraq. :)
The ArchitectThread starterFL · Sep 10, 2009#13
wouldn't it be best to run anything you want to ground back to the - battery post? or would difference be negligible.
TamagoOff Grid · Sep 10, 2009#14
Originally Posted by sqcomp ↑
Besides, the power flows on the path of least resistance.
power flows everywhere. it doesn't simply find the path of least resistance and not flow through higher-resistance conduits.
talnlnkySpokane, Wa · Sep 10, 2009#15
Originally Posted by Tamago ↑
power flows everywhere. it doesn't simply find the path of least resistance and not flow through higher-resistance conduits.
that's begging for a highly semantic debate.
sqcompBack at home · Sep 10, 2009#16
indeed...

How about this:

MORE current will flow through the path of least resistance. The amount of flow seems to me to be oppositely dependant to said path's resistance.

The amplitude or magnitude of the current flow in a path relies on the path's voltage and impedance. The lower the impedance (resistance) the greater the current...with a constant voltage. On the other hand the higher the impedance (resistance) the lower the current.

Thoughts?
talnlnkySpokane, Wa · Sep 10, 2009#17
Originally Posted by sqcomp ↑
indeed...

How about this:

MORE current will flow through the path of least resistance. The amount of flow seems to me to be oppositely dependant to said path's resistance.

The amplitude or magnitude of the current flow in a path relies on the path's voltage and impedance. The lower the impedance (resistance) the greater the current...with a constant voltage. On the other hand the higher the impedance (resistance) the lower the current.

Thoughts?
I think no more needs to be said unless it is said in a different thread...and i'm not even a huge fan of that either since it is so incredibly semantic already.
The ArchitectThread starterFL · Sep 17, 2009#18
I just received my shipment from Knu, this 1/0 cable is insane, it bends all over and has 5145 strands etc etc etc. Im off to home depot for random stuff Ill need to knock out the big 3.

Lastly, anyone know where the post is on the Alternator for the Alt to Batt Positive?
SlickHouston, Texas · Sep 17, 2009#19
Look at the last pic of first post, sqcomp took a picture of it i believe lol. It has a greay weather guard over it. Its above where the plug is.
The ArchitectThread starterFL · Sep 17, 2009#20
Originally Posted by Slick ↑
Look at the last pic of first post, sqcomp took a picture of it i believe lol. It has a grey weather guard over it. Its above where the plug is.
yea i found it at home depot when i was pokin around....its really really on there.
talnlnkySpokane, Wa · Sep 17, 2009#21
congrats.... you are doing what 100% of people with aftermarket electronics should be doing to their cars. It is the electronic equivalent to using 20% off coupons at stores to save money so you can get more stuff.
The ArchitectThread starterFL · Sep 17, 2009#22
not sure i follow the metaphor but ill assume its good...i just finished and im a bit tired. pics and an HD vid to come.

off for a test ride.
The ArchitectThread starterFL · Sep 17, 2009#23
Here are finished pics etc.

During the install something touched something and a loud boom/spark occured....

During the test ride with no music the cap showed a voltage of a mere 13.61 steady on the highway at 75MPH where it would normally be 13.99-14.17

On the way back from the test ride on 40mph roads the voltage started increasing slowly to 13.68-13.74 so somethings happening in regards to voltage returning to at least normal.

I currently have the yellow top charging even though it is already supposedly well charged.

anyways without further a due, pics.

feel free to suggest or otherwise. and I couldnt find any 1/0 shrink tube.


Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
talnlnkySpokane, Wa · Sep 17, 2009#24
don't know exactly what's going on... I wonder if your cap is related to this wierd issue.... I wonder if you need to discharge and then recharge it. I dunno... I also wonder if you could've somehow done damage to the alt when you dropped that cable... i dunno.... hard to say.
SlickHouston, Texas · Sep 17, 2009#25
A tad sloppy :P. Looks good man. Did you by any chance check your ground connection with a meter? Just asking out of curiosity, not because I think its wrong lol
The ArchitectThread starterFL · Sep 17, 2009#26
I dont ahve a test light to gischarge the cap effectively, are there any other handy ways?

yea that ground was the best although not THE best. but it is what it is which is good enough.

i overcompensated on wire lengths for each run since 1/0 KNUFLEKS is not cheap. I also wish there were more places to tie to.
talnlnkySpokane, Wa · Sep 17, 2009#27
Originally Posted by The Architect ↑
I dont ahve a test light to gischarge the cap effectively, are there any other handy ways?
hehe... hook it directly up to a sub.... You'd get POP... for about 1/100th of a second as the sub either pushes out, or sucks in.. and then holds it until the cap is drained.... hehe...

OK>... DON'T REALLY DO IT... DC looks wierd on speakers tho..... quick way to kill them tho. (don't think 12-14v would be high enough voltage to actually damage a sub... I'm way too lazy to do the math)
The ArchitectThread starterFL · Sep 17, 2009#28
alrighty then lol
The ArchitectThread starterFL · Sep 20, 2009#29
so uh I tried taking off the alt to batt run of 1/0 to see how that would effect my voltage issue.

At start up before the big 3 upgrade and before the "big spark" accident i guess you could call it, my card would jump to 14.08 - 14.17 and stabilize around 13.84 - 13.99

Now after the spark incident with the run of 1/0 for alt to batt itll jump to 13.55 - 13.61 and sit right around there.

And when I removed that run of 1/0 and turned my car on it sat at 12.30! wth so I quickly reattached that run of 1/0 and its back to 13.5/6ish
The ArchitectThread starterFL · Oct 5, 2009#30
alright well I got the HO Alternator from DC Power Engineering and it does not fit at all like they said so very surely it would. It has already been returned to them and I am awaiting a refund.

DONT USE DC POWER
talnlnkySpokane, Wa · Oct 5, 2009#31
lame....thanks for the info tho.
sqcompBack at home · Oct 6, 2009#32
look at powerbastards...

I have to wait until April for mine. The owner seems to communicate well and does offer that 1 year no questions asked warranty.
The ArchitectThread starterFL · Oct 6, 2009#33
right now im working with iraggi, he seems a little more down to earth and claims to use OEM casings for the fit.

we'll see.
sqcompBack at home · Oct 6, 2009#34
I'm interested to know. I'll be looking at your experience. I'll pick one up asap after I get back home in the spring.
POORSHANE CT · Oct 6, 2009#35
I ran pos and neg from altenator under engine cover to battery

4 attachments not included in this copy

The ArchitectThread starterFL · Oct 6, 2009#36
awesome idea....seriously

im gonna have to redo a few wires soon.

I just payed for iraggi for a 300amp alt with a 1 5/8" billet aluminum pulley with a .5" shorter serpentine belt.

guess we'll see how this one goes.
talnlnkySpokane, Wa · Oct 6, 2009#37
Originally Posted by The Architect ↑
awesome idea....seriously

im gonna have to redo a few wires soon.

I just payed for iraggi for a 300amp alt with a 1 5/8" billet aluminum pulley with a .5" shorter serpentine belt.

guess we'll see how this one goes.
A buddy of mine ran a 15v 280amp iraggi alt back around 03/04 in a honda civic. QUALITY PRODUCT!... he ran his amps at .7ohms (over 3000watts worth in power) and his electrical never dropped below 14v.

I'd recommend him in a heartbeat.

As for the wire under the engine cover... I'd personally loom that just to be safe.
The ArchitectThread starterFL · Oct 6, 2009#38
im going to voltrex all my cables once i get some.

how hot does it get under that engine cover?
The ArchitectThread starterFL · Oct 8, 2009#39
just got the stock 80 Amp backup alternator i ordered from lowmileageparts.com

Ill be using this as a comparison the the HO alt i get from iraggi.
SlickHouston, Texas · Oct 10, 2009#40
I'm eagerly awaiting the result from the iraggi :) Lets hope it works. Im glad you have the balls and the cash to experiment for the greater good :)

A quick question though, what was the original game plan for the DC alt concerning the electronics. If it would have fit, was it going to be a plug n play? thanks
The ArchitectThread starterFL · Oct 11, 2009#41
well 90% of the PnP part was the fitment and it was off so that was a massive fail. Other than that it looked as if the ports and connection were appropriate.

Dom Iraggi has probably the best customer service so far, he's very responsive and reassuring seeing as how I told him my entire DC story along with my concerns and worries about fitment and all the like.

The alt ill be getting will be .5" larger in most directions so as to be able to make 300amp of it but the mounting points will be the same he said.

From the stock casing he could only make an alt to produce around 150-180amps which for a lot of owners would be a massive help but I chose to go all out so Im just hoping itll fit.

Ill be doing a side by side comparison with an OEM alt to see if itll work just by eyeballing and measuring it.
SlickHouston, Texas · Oct 11, 2009#42
I checked his Ebay page, I didnt see a 300A for the Yaris. He does make it though, its just not listed?? And if you dont mind me asking, how much did you throw down for 300A?
The ArchitectThread starterFL · Oct 11, 2009#43
its probably not listed bc he cant make it "stock" per say bc its not the exact yaris case.

the ones you see on his page are most likely (99%) the ones that he builds from factory OE casings.

the one i ordered that i hope and should fit was 499 then i got the special 1 5/8" billet aluminum pulley for 45 and the shorter serpentine belt for 15
SlickHouston, Texas · Oct 11, 2009#44
For 300A thats not a bad deal at all. Well, im officially excited :D I hope all works out. Any estimate on how much power will be available? Like, would it support a 10KW system do you think?
The ArchitectThread starterFL · Oct 11, 2009#45
10KW is a litttttle bit rough.

figure the car will use 25amps for typical car stuff so im working with maybe 270 amps

270 Amps x 14 Volts = 3780 usable watts (assuming your yaris sustains 14v typically)

Whats more important is the idling, I should get around 140-150 amps at idle but we'll see. Im the worst skeptic
SlickHouston, Texas · Oct 11, 2009#46
well then thats just perfect for my two 900 RMS subs :D I cant wait to blow em and then upgrade to nightshades :)
The ArchitectThread starterFL · Oct 11, 2009#47
there goes the rear of your yaris.
goku87AK · Oct 12, 2009#48
and what amp are you planning on using to power your nightshades?
SlickHouston, Texas · Oct 12, 2009#49
I'm not totally familiar with the capabilities of the NS. They are 1500 RMS a piece. I've read, heard, and seen great things about the AP 30001d. But again idk. If it's too much I'll go to one NS and a ap 1500. Which would make sense bc the 3000 is just 2 strapped 1500
talnlnkySpokane, Wa · Oct 12, 2009#50
Originally Posted by The Architect ↑
10KW is a litttttle bit rough.

figure the car will use 25amps for typical car stuff so im working with maybe 270 amps

270 Amps x 14 Volts = 3780 usable watts (assuming your yaris sustains 14v typically)

Whats more important is the idling, I should get around 140-150 amps at idle but we'll see. Im the worst skeptic
if you're a skeptic... then change your equation.. 270*13 = 3510

when you have a bass hit, it's not uncommon for your voltage to sag 1volt, also... that alt will charge your system quickly... depending on how he makes the voltage regulator, the voltage may drop down quickly to the mid to high 13's.