thanks for clarifying Scott. Still getting it.
Crashy Lives
357 posts · 160,819 views · page 7 of 8
Replies continued
I have found a crashy project car in Dayton Ohio. I am trying to get them to sell it.
its too bad you need the key for the push to start to work. lol seems like just adding a step :)
It really is. It's one of those features that a lot people think is kind of cool on the JDM Yaris. Unfortunately, to make it complete and keyless would be a bit cost prohibitive.Originally Posted by TinyGiant ↑its too bad you need the key for the push to start to work. lol seems like just adding a step :)
yeah . its a cool idea but something i wouldnt do.. better projects to do :)
i just had to replace a friends ignition in his car. (his key broke off deep in the lock cylinder.. lol couple hours later with a lock wrench, flat head and hammer we got it out.. 100 later for the new lock and $2 for new keys (so we can bypass the chip) we keep the old key head on his key ring and the new key in the cylinder .. lol its ghetto but it works :) I saved him 900 bux dealership wanted to run him over the coals i guess.
i just had to replace a friends ignition in his car. (his key broke off deep in the lock cylinder.. lol couple hours later with a lock wrench, flat head and hammer we got it out.. 100 later for the new lock and $2 for new keys (so we can bypass the chip) we keep the old key head on his key ring and the new key in the cylinder .. lol its ghetto but it works :) I saved him 900 bux dealership wanted to run him over the coals i guess.
I was thinking about buying another Kawasaki Mule for my farm . I think a salvage Yaris would do fine . Thanks CT 🙇🙇🙇🙇🙇😎😎😎
That photo is brilliant! would like one of those for my round of golf!
is crashy ready for the winter season??? 😁
Crashy is sooo ready, that I don't think we will get any snow this year. I even installed a seat heater in her drivers seat. I was off most of Thanksgiving week and had some serious play time with my lift getting all three vehicles ready for winter. Crashy got new brake rotors (drilled and slotted), calipers, and pads and fluid (she had a bent caliper that was a bit annoying scraping wise, and her rotors were incredibly rusty-flakey thanks to spending so much time sitting in a swampy area before I bought her.Originally Posted by DandiDani ↑is crashy ready for the winter season??? 😁
She also got an oil change with synthetic oil. She only had 3 miles on her existing oil, but it was a year old, so I figured with how much she plowed last year, she deserved fresh.
I also drained, flushed, and replaced her coolant, since the prior owner had put some green fluid in her.
Finally, I remounted her dash top to get back my coffee mug holder.
I am looking into getting (or welding up) a flat bed car trailer so she can do some traveling. A friend of mine bought a place in Vermont that has about 100 acres of snowy fields that would make for some serious Crashy fun.
Sounds like you have been busy! I would like to see what Crashy can do in Vermont. Do take some video if you go.👍
if u got ur yaris to tow crashy, that would be epic
+1Originally Posted by yaris2010RS ↑if u got ur yaris to tow crashy, that would be epic
Wow! Crashy is lookin' good! That's the car I needed on my commute to work this morning with over 15cm of snow! I almost got stuck twice! Grrrrrr
Is she an all wheel drive?? How'd you pull that off?? Did you change the tranny and drive train?
Is she an all wheel drive?? How'd you pull that off?? Did you change the tranny and drive train?
She's still just a front wheel drive Yaris. With the way that I designed the plow frame for her, most of the force against the plow is converted to traction. The ATV tires make a world of difference as well.Originally Posted by Eatoman ↑Wow! Crashy is lookin' good! That's the car I needed on my commute to work this morning with over 15cm of snow! I almost got stuck twice! Grrrrrr
Is she an all wheel drive?? How'd you pull that off?? Did you change the tranny and drive train?
Nice project on Crashy. She's a keeper! 🤘
Keep it up!!
Keep it up!!
Crashy and the Blizzard
From yesterday's storm, we ended up with 15" of snow and with drifts over 3'. Crashy once again did a great job of clearing my 7000+ sq ft driveway. I recently gave her a set of rally style lights (wired to the headlight feed, since her headlights were gone) and a driver's side seat heater. With the seat heater, the 30+ MPH winds blowing, while I was plowing, didn't bother me a bit.
Picture not included in this copy
From yesterday's storm, we ended up with 15" of snow and with drifts over 3'. Crashy once again did a great job of clearing my 7000+ sq ft driveway. I recently gave her a set of rally style lights (wired to the headlight feed, since her headlights were gone) and a driver's side seat heater. With the seat heater, the 30+ MPH winds blowing, while I was plowing, didn't bother me a bit.
Picture not included in this copy
1 attachment not included in this copy
That is just all kinds of awesome. 👍
^ +1 ga-google-zillion
LOVE IT!
Get a windshield too! 🙂
Awesome on how a car that would be scrapped and recycled by now, has a new life and shows an extreme potential a Yaris can have.
Scott,
You have mad skills! Crashy is awesome!
You have mad skills! Crashy is awesome!
bump on this, any new progress ? :D
She recently finished her 3rd year of plowing. I haven't done much new with her, but I think soon I will be adding a power dump bed to make her even more useful in the summer months.Originally Posted by 09sedan ↑bump on this, any new progress ? :D
I also purchased a spare crank pulley and am working on welding a triple V-belt pulley to it to allow me to drive a 20 KW generator head, so she can quietly power the house during the next week long power outage (like the two we had with the hurricane last August and snow storm last October).
3rd year of plowing?!!! Wow... time flies when you're having fun... has it been that long already?
Poor thing, she looks a little bit like Frankenstein but beauty is in the eye of the beholder ;)
Congrats on generating one of the most intereting / fun Yaris-rescue / DYI on this board.
Poor thing, she looks a little bit like Frankenstein but beauty is in the eye of the beholder ;)
Congrats on generating one of the most intereting / fun Yaris-rescue / DYI on this board.
Picture not included in this copy
Originally Posted by CTScott ↑She recently finished her 3rd year of plowing. I haven't done much new with her, but I think soon I will be adding a power dump bed to make her even more useful in the summer months.
I also purchased a spare crank pulley and am working on welding a triple V-belt pulley to it to allow me to drive a 20 KW generator head, so she can quietly power the house during the next week long power outage (like the two we had with the hurricane last August and snow storm last October).
Darn! I'd have sold you my crank pulley, lol.
In preparation for the latest mods on Crashy, this morning I finished chopping the back of the roof off. The final cut will actually be on the other side of the tape, but I left myself enough material to be able to bend it over and weld it to give it some strength and cover the opening.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
2 attachments not included in this copy
Looks good. What are the plans for the tailgate?
She's about to get a 15 cu ft power dump bed back there.Originally Posted by KCALB SIRAY ↑Looks good. What are the plans for the tailgate?
exxxcellent!
Didn't you have an idea for a generator too?
looks like you need a rear bumper! and i have 2! lol
From strength to strength. Perfect!
Ranks right alongside my favorite New Beetle pickup.
http://newbeetle.org/forums/rumors-i...le-pickup.html
Ranks right alongside my favorite New Beetle pickup.
http://newbeetle.org/forums/rumors-i...le-pickup.html
I was unaware of Crashy until just now. Other then seeing your avatar that is, which I couldn't comprehend.... very cool! The Yaris as a pickup looks pefect, obviously meant to be.
I just completed putting a dump bed on my Dodge flatbed, it's the same hydraulic setup I had on another truck for 12 years. Bought from Northern Hydraulics, it'd be too much for Crashy, but I'd be happy to PM you some pics showing the geometry of how they work, no use re-inventing the wheel. Once you see the dynamics of it, where the cylinder is, the hinge points, etc., you'll see it would lend itself to being home brewed. Hell I can just post a couple pics here if anyone else is interested.
I just completed putting a dump bed on my Dodge flatbed, it's the same hydraulic setup I had on another truck for 12 years. Bought from Northern Hydraulics, it'd be too much for Crashy, but I'd be happy to PM you some pics showing the geometry of how they work, no use re-inventing the wheel. Once you see the dynamics of it, where the cylinder is, the hinge points, etc., you'll see it would lend itself to being home brewed. Hell I can just post a couple pics here if anyone else is interested.
As always, very awesome what you did with Crashy. Thanks for posting the pics!
It's funny that you mention the dump bed pics. I had a guy over chipping some trees for me yesterday and when he went to dump the chips from his truck, I pulled out my phone and started snapping some pics. On Crashy I am using a 1320 lb rating electric linear actuator with a 12" stroke.Originally Posted by Idahotom ↑I was unaware of Crashy until just now. Other then seeing your avatar that is, which I couldn't comprehend.... very cool! The Yaris as a pickup looks pefect, obviously meant to be.
I just completed putting a dump bed on my Dodge flatbed, it's the same hydraulic setup I had on another truck for 12 years. Bought from Northern Hydraulics, it'd be too much for Crashy, but I'd be happy to PM you some pics showing the geometry of how they work, no use re-inventing the wheel. Once you see the dynamics of it, where the cylinder is, the hinge points, etc., you'll see it would lend itself to being home brewed. Hell I can just post a couple pics here if anyone else is interested.
Just keeps getting better! Any plans to put front fenders on it?
I really like the pick-up look on that Yaris. What a great idea!
I wish Scott would make some mini die cast Crashy's. I'd have one as a keyring.
That's pretty friggin sweet.Originally Posted by SailDesign ↑From strength to strength. Perfect!
Ranks right alongside my favorite New Beetle pickup.
http://newbeetle.org/forums/rumors-i...le-pickup.html
At some point I would like to put front fenders with flares on her. When I am plowing snow, if I spin a front tire I spray a rooster tail of snow straight at the front seat on the side of the spin.Originally Posted by Altitude ↑Just keeps getting better! Any plans to put front fenders on it?
A linear actuator.....good idea.
Here's a shot of the way my flat bed dump is configured, BTW, I have found over the years that nothing seems to be required to keep the bed in the down position, gravity does just fine. I only secure the bed (with a chain binder under the frame) if I am carrying one of my 22' long by 10' wide solar arrays on the racks, they might devolup a little up force going down the road so I take no chances there! Of course a linear actuator will take care of that anyway.Picture not included in this copy
Here's a shot of the way my flat bed dump is configured, BTW, I have found over the years that nothing seems to be required to keep the bed in the down position, gravity does just fine. I only secure the bed (with a chain binder under the frame) if I am carrying one of my 22' long by 10' wide solar arrays on the racks, they might devolup a little up force going down the road so I take no chances there! Of course a linear actuator will take care of that anyway.Picture not included in this copy
couple of those and you could turn Crashy into a real-life Transformer...
http://www.northerntool.com/shop/too...3243_200333243
A good source for the linear actuator maybe.....
A good source for the linear actuator maybe.....
Exactly. I ordered the 12" stroke version of that one.Originally Posted by Idahotom ↑http://www.northerntool.com/shop/too...3243_200333243
A good source for the linear actuator maybe.....
Making progress with the dump bed. Last night I finished welding the support assembly for the rear pivots:
Picture not included in this copy
Picture not included in this copy
1 attachment not included in this copy
Wow this is too awesome!
any updates on the dump bed??