Yarisworld Archive

GROUP BUY - Megan Racing 4-1 Header...

485 posts · 86,101 views · page 9 of 10

Replies continued

dngzvancouver · Dec 8, 2006#401
GOT MINE!!!!!
dngzvancouver · Dec 8, 2006#402
CRAP! NO HAT.... BUT A TSHIRT!! omg.. its XL -_-
ChinoCharlesOH · Dec 8, 2006#403
Mine came in! Look sexy... I'll be on the phone Monday morning to find out when I get them on the dyno.

If you have a black hat and would like to trade for a white one, PM me. 🙂

EDIT: After looking at them for a few minutes, let me say that that is the most laughably small header I have ever seen. If this isn't the most endearingly tiny car on Earth I want to see what is. How cute!
ism3tSouthern California · Dec 9, 2006#404
ok, pics are impossible to take, sorry team.

however they sent the kit with metric threaded screws, but apparently they dont fit. my guys says you have to find standtard bolts to fit, so right now i got nothing holding the new headers to my cat, my car sounds like a lawnmower. im going back tomrrow so we can find out what size bolt we need. good luck.!
riceboyThread starterCAN · Dec 9, 2006#405
Received Members in Red

1. riceboy
2. ism3t
3. Chris07LB

4. eco
5. ChinoCharles
6. dngz
7. Ran Kizama
8. redglare45

9. MD2020
10. punch
11. skc
12. Black Yaris

Sorry bout the lack of tracking numbers I guess those got lost in the mail?!? In any case hope everyone's installs go smoothly. The cats on the Yaris are all located in the midpipe and that's why MR decided not to do the full exhaust. The header as is should be fine.. if anyone else has received their shipment please feel free to update the above list.
skcSurrey, B.C. · Dec 9, 2006#406
i got mine too
ecoAtlanta · Dec 9, 2006#407
Ive got mine,but it looks like UPS kicked the package around,the O ring that came in the gasket package is smashed on one side,and cracked,the gasket itself is pretty badly bent,but that can be flattend out,and shouldnt be a problem,but the other peice worries me,Ill post pics tomorrow.The install will need to wait,and whats the deal with the screws.
dngzvancouver · Dec 9, 2006#408
what? there's sumthing wrong the screws? my gasket was a lil bent too.. but i guess once it's on nice and tight, itll be perfectly flat. hmm.. sumbody update with the screws please...
Ran KizamaCanton, GA · Dec 9, 2006#409
Originally Posted by ism3t ↑
however they sent the kit with metric threaded screws, but apparently they dont fit. my guys says you have to find standtard bolts to fit, so right now i got nothing holding the new headers to my cat, my car sounds like a lawnmower. im going back tomrrow so we can find out what size bolt we need. good luck.!
Wait a sec, is it the bolts holding the header to the engine, or to the cat? If it's to the cat, shouldn't you use the factory bolts? Hmm...I'll take a look at mine today when I swap it. Worse case scenario, there's an ACE Hardware 2 mins away. 😁
ItsMyDailyLos Angeles, CA · Dec 9, 2006#410
Originally Posted by ism3t ↑
ok, pics are impossible to take, sorry team.

however they sent the kit with metric threaded screws, but apparently they dont fit. my guys says you have to find standtard bolts to fit, so right now i got nothing holding the new headers to my cat, my car sounds like a lawnmower. im going back tomrrow so we can find out what size bolt we need. good luck.!
You should be able to use the factory bolts again.
ecoAtlanta · Dec 9, 2006#411
Anyone else install,and how important is the O ring that came in the gasket bag,I dont know what that is for,Ive never installed a header.I really want to know if the OEM screws are used for the install,if not,Im not going to install untill next weekend.
MD2020TN · Dec 9, 2006#412
Got mine yesterday, with a Black hat ha!! Looking like east coast got black hats west coast got white hats...
ItsMyDailyLos Angeles, CA · Dec 9, 2006#413
what is the size of the collector? If it's bigger then 2" then those with stock exhaust may experience power loss. Can you say bottleneck.
Black YarisToledo, OH · Dec 9, 2006#414
I got mine yesterday, doing the install tomorrow... BTW I got a white hat as well
Chris07LBNew Jersey · Dec 9, 2006#415
Originally Posted by MD2020 ↑
Got mine yesterday, with a Black hat ha!! Looking like east coast got black hats west coast got white hats...

I got white.. but I dont wear hats so,.....
riceboyThread starterCAN · Dec 9, 2006#416
Received Members in Red

1. riceboy
2. ism3t
3. Chris07LB
4. eco
5. ChinoCharles
6. dngz
7. Ran Kizama
8. redglare45

9. MD2020
10. punch
11. skc
12. Black Yaris


We should get ours soon Punch... we're the furthest away from California.. hopefully the shipments aren't stuck in customs....

Somebody get them installed already!!!!!!
Chris07LBNew Jersey · Dec 9, 2006#417
Man you guys are a dissapointment.. do I have to go install mine, with bed ridden flu an all?? 😛

Someone make us proud, and get 'em on!!!
Chris07LBNew Jersey · Dec 9, 2006#418
Originally Posted by ItsMyDaily ↑
You should be able to use the factory bolts again.
Go to page one.. looks like they reused the original bolts indeed.

Im guessing the studs included with the new header is for the collector, but not pre-installed?? Humm, maybe they had clearence issues when slipping the header in place, with the studs installed before hand?

Man, I should just suck it up tomorrow after work, and get mine on!! This is soo unlike me to have mods sitting. 👎
redglare45Pomona / Pasadena, California · Dec 9, 2006#419
Originally Posted by Chris07LB ↑
Go to page one.. looks like they reused the original bolts indeed.

Im guessing the studs included with the new header is for the collector, but not pre-installed?? Humm, maybe they had clearence issues when slipping the header in place, with the studs installed before hand?

Man, I should just suck it up tomorrow after work, and get mine on!! This is soo unlike me to have mods sitting. 👎
Chris, I thought you would have a write-up for us already.

I got mine on, used the stock bolts & nuts on the header & collector. Everything seemed to bolt up fine. No issues with it yet. No check engine codes. Took it for a drive and drove it for like 25 miles and so far so good. 🙂
Chris07LBNew Jersey · Dec 9, 2006#420
Got my sick ass outside, and in 15minutes, its almost complete..

Pictures to come shortly....
redglare45Pomona / Pasadena, California · Dec 9, 2006#421
Great Chris!!!
punchBarrie, ontario · Dec 9, 2006#422
Originally Posted by Chris07LB ↑
Got my sick ass outside, and in 15minutes, its almost complete..

Pictures to come shortly....
is it really that easy??? i hope so, alot of so called easy mods turned very difficult with rusted bolts, etc...
Ran KizamaCanton, GA · Dec 9, 2006#423
Mine's done! No hang-ups at all! All the parts went on great! Also...

NO CHECK ENGINE LIGHT! NO RASPY SOUND!

The car sounds relatively normal, just a little louder inside.

The hardest part of the install was the removal of the stock header. Putting on the Megan takes about 15 mins. Good stuff! Here are some notes I'd like to mention...

1. All the stock bolts and nuts that hold the header to the engine are reused.
2. I had to hammer on the new donut with a rubber mallet. Easy.
3. The three studs, bolts, and washers are for connecting the header to the exhaust pipe and to the little bracket right there.

The car doesn't seem to have lost anything down low, but the top end is a lot more spirited. A quick dash onto the interstate brought this to truth.

Thanks for an excellent group buy! Good luck to all those still waiting to install! 👍
Chris07LBNew Jersey · Dec 9, 2006#424
Pics are being edited as i type... Ill make a completely new How_To post. 😎
Chris07LBNew Jersey · Dec 9, 2006#425
Originally Posted by redglare45 ↑

I got mine on, used the stock bolts & nuts on the header & collector.
DO NOT USE THE ORIGINAL COLLECTOR BOLTS!!!

The original bolt is tapered, and will only thread so far... Use the included 3 studs, to replace the bolts. (1) for bracket (2) for the collector.
Black YarisToledo, OH · Dec 9, 2006#426
the general time from for this install is 15-30 minutes total? Were you using a lift or at home on the garage floor?
GalavoxxSan Francisco · Dec 9, 2006#428
Just curious as they look pretty beefy: what is the diameter of one of the header tubes?
GalavoxxSan Francisco · Dec 9, 2006#429
And thank you for the how to. Another great job!!
ChinoCharlesOH · Dec 9, 2006#430
Rock! Nice Chris, thanks!
Black YarisToledo, OH · Dec 9, 2006#431
I stopped by my mom's house to show the header to my step-dad (who is a machinist & hot rodder) he thought this header was VERY nice, thick flange, and nice welds
ecoAtlanta · Dec 10, 2006#432
Ok,I gather that the donut is the peice that came in the bag with the gasket,is it ok for that to be cracked and beatin up alittle.
Ran KizamaCanton, GA · Dec 10, 2006#433
Good write up Chris! I've been enjoying mine. I'd really like to see it come to life with an intake and exhaust.
ecoAtlanta · Dec 10, 2006#434
Can anyone answer my question and ease my worries?
dngzvancouver · Dec 10, 2006#435
what is that piece for?? if not, WARRANTY!!
Chris07LBNew Jersey · Dec 10, 2006#436
Originally Posted by eco ↑
Can anyone answer my question and ease my worries?
As long as its still "round", and installed like in my post, it will be fine.. its gets sandwiched to shit (As in fits perfect in the taper) anyway once the collector is tightened.

Guys, bump the How_To post for your fellow members. 😎
Chris07LBNew Jersey · Dec 10, 2006#437
Originally Posted by Ran Kizama ↑
Good write up Chris! I've been enjoying mine. I'd really like to see it come to life with an intake and exhaust.
I modded my stock intake before doing the header install last night, and that alone, woke the car up a bit. Im sure with the addition of a high flow filter, it may net even better gains.. but im happy with the 10minutes work, and the results I got. 😁
ecoAtlanta · Dec 10, 2006#438
Thanks Chris.YOU DA MAN
Black YarisToledo, OH · Dec 10, 2006#439
Header officially installed, the donut realy does get squished.... I am going to go back in a retouque everything in a few days after everything is rattled into place
riceboyThread starterCAN · Dec 10, 2006#440
great diy as usual from Chris... hope everybody gets a chance to get these installed... i'm stuck playing the waiting game for now...
ecoAtlanta · Dec 10, 2006#441
Sorry to hear that riceboy,that sucks,after all your great work,you are one of the last to receive(and maybe install) the header.But great job on the GB,thanks.
riceboyThread starterCAN · Dec 10, 2006#442
no worries.. just glad that there's only two outstanding shipments....
Black YarisToledo, OH · Dec 10, 2006#443
Anyone putting the Megan racing stickers on?
ecoAtlanta · Dec 10, 2006#444
Not me,Im thinking of doing a custom all black emblem of all the companys Ive used so far,I want it to be stealthy,sorta like you cant see it until your up close to it,or the light hits it right and your at a distance.I want it to be seen at a car show more then on the road.
Black YarisToledo, OH · Dec 10, 2006#445
I was thinking of doing something similar just with a dark gun metal grey
ecoAtlanta · Dec 10, 2006#446
So is the heat sheild re-used,or do I just leave it out.
Black YarisToledo, OH · Dec 10, 2006#447
Originally Posted by eco ↑
So is the heat sheild re-used,or do I just leave it out.
heat shield...... gone
ecoAtlanta · Dec 10, 2006#448
Ok.
riceboyThread starterCAN · Dec 10, 2006#449
PS: Just wanted to remind everybody to send out their warranty cards, it'll just make it easier in case anything comes up and you need to get in touch with MR customer service.
ecoAtlanta · Dec 11, 2006#450
So these down pipes ar a bigger diameter right,and the collector is bigger?