Chris07LBOriginal postNew Jersey · Dec 9, 2006#1Special thanks to RICEBOY for heading up this Group Buy, and making it all go smooth. 👏
Very easy to install, and with the correct tools, it can be installed within 30 minutes, to an hour taking your time.
First, here's how the two compare.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Lets get started...
First remove the (4) 10mm bolts holding the heat shield to the stock header.
Next, jack up the car, and support it with jack stands at all four corners.
With a 3/4" drive rachet, 12" extension, and a 15mm socket, remove the (2) bolts holding the collector to the header. Crawl out from under the car, and under the hood remove the last (3rd) 15mm bolt holding the support bracket to the bottom of the header. Discard these bolts. You will be using the (3) replacement studs, washers, and lock washers included with the Megan header.
Picture not included in this copy
Picture not included in this copy
Next a 1/4" drive rachet, 12mm socket, and a 12mm box wrench will be used to remove the (2) nuts and (3) bolts holding the stock header to the block.
Unplug the O2 sensor, and remove stock header.
Remove O2 sensor from header bung, and install onto Megan header.
Install new donut to Megan header, and new gasket to block.
Picture not included in this copy
Install the (2) included studs on the collector. They will only thread on one way.
Picture not included in this copy
Slip the header inside the car, and align the studs to slip into the collector. Snug up the collector with the included washers, lock washers and nuts (17mm). Install 3rd stud, washer and lock washer into support bracket.. sung up only for now.
Re-install the (2) nuts and (3) bolts to hold the new header to the block. Torque to specs. Now tighten the support bracket and collector nuts.
Picture not included in this copy
Be sure to route O2 sensor correctly onto the metal hold bracket. This will keep the wires from touching the header and melting.
Picture not included in this copy
Enjoy it for a few hundred miles, then re-torque to specs again. 🤘
Replies 125
Black YarisToledo, OH · Dec 9, 2006#2nice, I can't wait till tomorrow morn... kinda like Christmas :)
acrbillchicago · Dec 9, 2006#3What kind of power could you expect from that header? Would you say the new header is lighter than the old one w/heat shield?
I would have re-used that OEM MLS gasket. Far superior to the one that seems to have come with the header.
Chris07LBThread starterNew Jersey · Dec 9, 2006#4 Originally Posted by
acrbill ↑
I would have re-used that OEM MLS gasket. Far superior to the one that seems to have come with the header.
I was tempted to, as I have always used metal gaskets on all our engines with aftermarket headers, but I decided to test Megan's kit the way it is being sold. Hopefully they can get some feedback, either positive or negative from all the GB members. If it becomes an issue with leaks or blowouts, a simple swap for the stock metal gasket is 15 minutes away. 😁
spkrman2 · Dec 10, 2006#5sweet, looks very easy!
ecoAtlanta · Dec 10, 2006#6Looks like the holes on the OEM gasket look bigger,better maybe.
Chris07LBThread starterNew Jersey · Dec 10, 2006#7The size of the holes on the Megan header, match the included gasket perfectly.
ecoAtlanta · Dec 10, 2006#8Then the new gasket should be better,interms of suface area and possible leaks,but deffinitly not as strong as OEM.
CASTREXCosta Rica · Dec 10, 2006#9Sooooooo.... did you notice any improvements?
ChinoCharlesOH · Dec 10, 2006#10Other than sound, nobody is going to notice 5 hp...
We will have dyno numbers soon for this piece. I'll know when tomorrow.
FastnxCanada · Dec 11, 2006#11 Other than sound, nobody is going to notice 5 hp...
On a 108hp engine, yes you will.
I have never seen a picture of the stock header until now. If you are keeping the cat in the stock location, it is difficult to imagine being able to improve upon the stock unit by very much. The main difference seems to be the size of the tubing.
ChinoCharlesOH · Dec 11, 2006#12 Originally Posted by
Fastnx ↑ On a 108hp engine, yes you will.
Keep telling yourself that... 😆
ViolinNew Jersey · Dec 11, 2006#13Do you think you could have done it with only the front of the car raised? (I only have one pair of jack stands but I'm always looking for an excuse to buy more tools.)
Chris07LBThread starterNew Jersey · Dec 11, 2006#14 Originally Posted by
Violin ↑ Do you think you could have done it with only the front of the car raised? (I only have one pair of jack stands but I'm always looking for an excuse to buy more tools.)
Yes.
Chris07LBThread starterNew Jersey · Dec 11, 2006#15 Originally Posted by
CASTREX ↑ Sooooooo.... did you notice any improvements?
Actually, yes. The car seems much smoother to drive the entire powerband.
No real increase in sound with my stock exhaust, but it does feel a bit stronger when crusing at 65mph, then hitting the gas to pass a car.
Smooth, smooth is the best way I can describe it.. no laboring to get thru the gears.
ecoAtlanta · Dec 11, 2006#16Chris,when you removed the old header,did you pull it out from the top,any trouble with tower bar installed.I tried to get Toyota to install it for warranty reasons,put they wont touch it,its not a TRD or SSC part,I was going to ask him what SSC was but I got into asking why he couldnt actually install an after market peice.So I guess Im going to do this soon,ohya Chris,you think it would be easier to intall my new crank pulley when the header is out,or should I just go ahead with the header install,because the pulley is coming straight from Japan,C-One was sold out in the US.
skcSurrey, B.C. · Dec 11, 2006#17installed mine today 😎
installation is easy. straight forward. Thx Chris07LB for making even easier.
i got little annoying sound on accelleration and sometimes on shifting.
think i overtightened collector bolts. i'm going to check all the torque specs again tomorrow.
other than that i feel little gain on mid and high rpms. accellerates much smoother and little faster.
i didn't feel any loss at row. 👍
Chris07LBThread starterNew Jersey · Dec 11, 2006#18 Originally Posted by
eco ↑ Chris,when you removed the old header,did you pull it out from the top,any trouble with tower bar installed.I tried to get Toyota to install it for warranty reasons,put they wont touch it,its not a TRD or SSC part,I was going to ask him what SSC was but I got into asking why he couldnt actually install an after market peice.So I guess Im going to do this soon,ohya Chris,you think it would be easier to intall my new crank pulley when the header is out,or should I just go ahead with the header install,because the pulley is coming straight from Japan,C-One was sold out in the US.
First, remove any upper strut bars, you wont be able to reach any bolts, nor will you be able to pull the header out.
Second, the header has to come out from the top of the engine bay, there is no room to pull it thru the bottom... trust me, its small enough to slip it out once its all unbolted. 👍
Third, the crank pulley is on the passenger SIDE of the engine, right in the wheel well... the header is in the center REAR of the engine, under the windshield area. One placement has nothing to do with the other, so do your pulley and header install, in any order you wish. 👍
Hope this helps. 🙂
KSIbuckyFond du Lac, WI · Dec 12, 2006#19you should post a DIY
ecoAtlanta · Dec 12, 2006#20Dude,your reading it!
riceboyCAN · Dec 12, 2006#21I think most of the ppl who got are driving manual... anyone with an auto on the GB???
ecoAtlanta · Dec 12, 2006#22Ya,me.
Chris07LBThread starterNew Jersey · Dec 12, 2006#23 Originally Posted by
KSIbucky ↑ you should post a DIY
Puuuuuuufffffff.... puuffffff.... give.
Chris07LBThread starterNew Jersey · Dec 12, 2006#24Transmission: Slush Box
Chris07LBThread starterNew Jersey · Dec 12, 2006#25 Originally Posted by bigsky2 ↑
Chris, excuse my ignorance but can you explain what a Slush Box transmission is?
Is it a variation of an Automatic transmission or just a term that people use for AT?
What some people that love the sporty-ness of a manual trans, call an automatic.
Slush box = Automatic
hasher22Australia Sydney · Dec 12, 2006#26Can u feeeeeel da powaaaa? seriously can u?
Chris07LBThread starterNew Jersey · Dec 12, 2006#27riceboyCAN · Dec 13, 2006#28+1 on the ol' butt dyno for me... it really helps to open up the power on the top end... and I haven't noticed any loss on the bottom end.... i don't know if it's just me but 3rd gear seems to pull forever!
ViolinNew Jersey · Dec 13, 2006#29You really should post a DIY.
Chris07LBThread starterNew Jersey · Dec 13, 2006#30 Originally Posted by
Violin ↑ You really should post a DIY.
Now there's an original idea.
Notthy[Yaris/S]07Puerto Rico · Dec 14, 2006#31where buy the header and what is the price? i want one for my sedan
Notthy[Yaris/S]07Puerto Rico · Dec 14, 2006#32eh heard that works of scion xa and xb its true?? somebody tried??
ViolinNew Jersey · Dec 14, 2006#33No the scion header won't fit.
dngzvancouver · Dec 14, 2006#34Am i the last to install my header?? Getting it installed this sat with my full cat back exhaust...
ChinoCharlesOH · Dec 14, 2006#35No, I just went out today and got a hydraulic jack, some jack stands and a torque wrench. Might get to it tomorrow but I doubt it.
punchBarrie, ontario · Dec 15, 2006#36 Originally Posted by
dngz ↑ Am i the last to install my header?? Getting it installed this sat with my full cat back exhaust...
cat back???? please share what you got??
Chris07LBThread starterNew Jersey · Dec 15, 2006#37 Originally Posted by
punch ↑ cat back???? please share what you got??
Take it to PMs guys... keep the DIY post on TOPIC. 👍
Notthy[Yaris/S]07Puerto Rico · Dec 16, 2006#38 Originally Posted by
Violin ↑ No the scion header won't fit.
thanx for the info jeje
KatanaUnder the hood! · Dec 16, 2006#39Nice job there!Great DIY Chris.
Chris07LBThread starterNew Jersey · Dec 16, 2006#40Thanks Kat.
punchBarrie, ontario · Dec 17, 2006#41 Originally Posted by
Chris07LB ↑ Take it to PMs guys... keep the DIY post on TOPIC. 👍
maybe you should get the mod to sticky the thread, and lock it then, this forum doesn't have rules, its like a free for all, ever since the mod allowed people to swear and such, this forum has lost much respect from me.
Chris07LBThread starterNew Jersey · Dec 17, 2006#42By locking it, it would only get burried away, as it would never get bumped to the top, if knowone replied.
I do agree with you to a point though, but lets not get into it here, there is a section just for that.
Now back to topic! 😎
ChinoCharlesOH · Dec 20, 2006#43OK, so I know you guys are wondering where the fuck the dyno results are.
Sunday rolls around and I pop open the install DIY and see that I need a 3/4 inch drive ratchet. Well, I decide I am going to try and torque those bolts off with a 1/2 inch drive, because I had honestly never seen a 3/4 inch ratchet and wasn't convinced I could easily find one. Took the heat shield off, got the car up on stands, and crawl under there... not happening. Chris wasn't kidding. You need some serious leverage for those collector bolts, as they are torqued to 32 lb/ft. Well, I go out and find a 3/4 inch drive ratchet at Autozone (surprisingly) but they don't sell any adapters or sockets for it. I then tried Sears hardware, regular Sears, Advanced Autoparts, Lowes, and Home Depot. Nothing. Called the dyno shop to see if he had one sitting around, and that was a big fat no. I was shit outta luck. So, I ordered a 3/4 inch female to 1/2 inch male adapter from Amazon.com and upon reception of that (should be here soon after Christmas) I will install the new header and go to the dyno shop.
Sorry for the teaser... of course the one tool I need seems to be a tool that you can't get without dropping thousands on a master mechanic's toolbox. God dammit. I'll update when I get the adapter and get the new header on. Sorry guys!
On the bright side, I now have a ratchet big enough to kill a large individual.
Doc ZaiusOttawa, ON, Canada · Dec 20, 2006#44would an extender arm for the 1/2" ratchet not work? something to give you more leverage?
ChinoCharlesOH · Dec 20, 2006#45It may have, but then again I also may have broken the ratchet... that is a lot of torque to put on a tinny ratchet. I'm all for being patient and using the right tool for the job.
H8SGASSan Diego, CA · Dec 20, 2006#46 Originally Posted by
ChinoCharles ↑ It may have, but then again I also may have broken the ratchet... that is a lot of torque to put on a tinny ratchet. .
Been there in the past and broke the ratchet, good choice in waiting 😁
Chris07LBThread starterNew Jersey · Dec 20, 2006#47Where's my phone call? I would have sent you out the tool you needed. Silly wabbit.
ChinoCharlesOH · Dec 20, 2006#48Actually Chris, I did call you... haha. Its a 330 number. Save that shit.
Chris07LBThread starterNew Jersey · Dec 20, 2006#49 Originally Posted by
ChinoCharles ↑ Actually Chris, I did call you... haha. Its a 330 number. Save that shit.
Word? Sorry Charles, did you leave a voice mail? Phones been acting a bit strange lately.
ChinoCharlesOH · Dec 20, 2006#50Naw, I didn't leave a voicemail. Its not a big deal homie, I've got the shit in the mail now! Thanks though, next time I'll leave one now that I know.