well, yes, i mean, some have short rams, some have long tubes, some have easy breathing filters while some don't.... we're arguing semantics here... It seems im assuming the instruction for the kit did not say anything about changing the intake and thats where everyone went wrong... adding more air to it when it wasn't needed...so tape up them thur filters
S/C owners: collecting information
151 posts · 33,597 views · page 3 of 4
Replies continued
Blitz has confirmed that they tested the kit on a stock car.
I'm going to wrap my beautiful aFe cone shaped filter in black electrical tape and leave a two inch diameter hole? That sucks (pun intended)
Mike, tape up your filter and see if your ignition timing climbs back up to double digits. I'm hoping to feel the additional power that the timing advance will give me.
I forgot that you have a CAI and that the filter is stuck in the fender. Anyways, I'm off work now and will go out to the parking lot with my trusty roll of blue masking tape to do some more "tuning".
The ECU is just too smart to fool. The car runs fine like this. Note that the bottom half of the filter at the tip is also taped up.
It's not going to win me points at any car show.
Picture not included in this copy
It's not going to win me points at any car show.
Picture not included in this copy
lol. definately no points for style. maybe someone can sell you their stock airbox that is lying around the garage or something? I'm sure there are people with them still, who don't care for them.
or would trade for an AFEOriginally Posted by PETERPOOP ↑lol. definately no points for style. maybe someone can sell you their stock airbox that is lying around the garage or something? I'm sure there are people with them still, who don't care for them.
My stock one is laying around... somewhere. Probably under a body kit that didn't sell. 🙄
lol
lol
haha, nice mad science there noogie-san, I look forward to reviewing your lab notes. 😁Originally Posted by LtNoogie ↑The ECU is just too smart to fool. The car runs fine like this. Note that the bottom half of the filter at the tip is also taped up.
SO... it sounds like we have obtained similar results, just by different routes--you are stabilizing your afr by lowering boost (via inlet restriction) and I am getting the same effect from boosting octane, thus allowing for more ignition timing advance...
i dunno, is that even right? 😕
I think that if I regress my car all the way back to stock, other than the S/C kit, I'll get the performance they designed for.
Next, my stock steelies and skinny tires go on. Then I'll raise my car with the OEM shocks and springs. That should get +5hp.
Next, my stock steelies and skinny tires go on. Then I'll raise my car with the OEM shocks and springs. That should get +5hp.
It's interesting to note that the Blitz installation manual specifies two types of intakes recommended for use with the kit, the Sus power air cleaner and Sus power core.
http://www.blitz.co.jp/products/aircleaner/suspower.htm
http://www.blitz.co.jp/products/airc...re_type_lm.htm
In japanese but tons of pics, piped all sorts of dayum ways depending on application--how do you think they compare to what you have, Long?
http://www.blitz.co.jp/products/aircleaner/suspower.htm
http://www.blitz.co.jp/products/airc...re_type_lm.htm
In japanese but tons of pics, piped all sorts of dayum ways depending on application--how do you think they compare to what you have, Long?
I don't think they use enough blue painter's tape for maximum performance.
Seriously, back to my previous post, if you could dare to run without an air filter, you could still not move any more air than what the diameter of the throttle body will let you pass. Now if the inlet to the stock airbox is smaller than the throttle body throat, some engineer at Toyota has determined that that is the optimum air inlet for whatever reason... performance (unlikely)... emissions... who knows.
We are requiring more airflow because we have a compressor, in effect sucking more air through that throttle body. You would think that we would need a bigger inlet than the stock 2" opening hence the larger filters.
I'm still trying to work this through my head why Peter's setup is not starving for air or for that matter my taped up setup.
Seriously, back to my previous post, if you could dare to run without an air filter, you could still not move any more air than what the diameter of the throttle body will let you pass. Now if the inlet to the stock airbox is smaller than the throttle body throat, some engineer at Toyota has determined that that is the optimum air inlet for whatever reason... performance (unlikely)... emissions... who knows.
We are requiring more airflow because we have a compressor, in effect sucking more air through that throttle body. You would think that we would need a bigger inlet than the stock 2" opening hence the larger filters.
I'm still trying to work this through my head why Peter's setup is not starving for air or for that matter my taped up setup.
one of you guys could also look into the effects of installing a larger throttle body, though I suppose it might make the lean condition worse...
i would think it would. i will use one during my tune.
I don't think that more air is what we need. I think we need same air as stock or IF we have more air, then we need more fuel.
right, right, true... just throwing ideas out there... One more thing I just thought of, the old "resistor trick" does have its merits, by telling the ECU/Fuel controller that the MAF is seeing a higher airflow, it ought to adjust with more fuel. In closed loop mode the ECU will be smart enough to compensate for this, but once in open loop mode it could actually allow a measurable enrichment. at just a few cents (or $50 on eBay), it could very we be worth trying 🙂
Yeah, it's too bad Garm cut his apart. I was going to offer him $80 for it.
Secondly, I found this plastic thingy in the garage that looked like a cross between a french horn and a solid bagpipe. From examininig archealogical sketches, I was able to determine that it was my stock airbox.
Secondly, I found this plastic thingy in the garage that looked like a cross between a french horn and a solid bagpipe. From examininig archealogical sketches, I was able to determine that it was my stock airbox.
LOL
let us know your AFR when you get it on!Originally Posted by LtNoogie ↑Yeah, it's too bad Garm cut his apart. I was going to offer him $80 for it.
Secondly, I found this plastic thingy in the garage that looked like a cross between a french horn and a solid bagpipe. From examininig archealogical sketches, I was able to determine that it was my stock airbox.
I actually put so much blue tape over my filter that the car almost stopped running. I had to pull over to give myself a "tune-up". What is totally wierd is that the AFR gauge was a constant 15. I cannot get this car to go rich for the life of me.
Just bizarre Long. 🤷 It's too bad we all have such different set-ups, makes it much harder to compare notes.Originally Posted by LtNoogie ↑What is totally wierd is that the AFR gauge was a constant 15. I cannot get this car to go rich for the life of me.
My latest observations: today I spent my first significant time on a major highway since installing the supercharger; drove about 30 minutes each way at constant 60-80 mph. At these speeds I was in boost for much of the time--and every time I hit even 1 psi of boost the AFR immediately went rich (11-12s), and (in due course 🙄) the scangauge showed open loop.
camell, is this what youre saying you wish yours would do?
Same nice performance as usual from the car btw, just different gauge readings from what I've seen on my daily commmute. At those lower typical engine loads and speeds its been going into acceleration induced open loop a lot less often--only at higher boost level (say 5 psi) + throttle position (above 50).
Since Blitz only supplies a fuel controller, how would they make the car enter open loop when they want it to? Isn't that a function of the ECU? I'm not technical enough to understand what controls what, exactly.
as far as we can tell, the fuel controller sends some kind of trigger signal to the ECU to make it go into open loop.
Where it's confusing is that camelll believes in some conditions, there is a small window of time in between the supercharger activating and producing boost, and the ECU actually going into open loop mode and thus providing enough fuel. So, in that small window, there would actually be a lean condition of not enough fuel to go with the increased mass of air.
Unfortunately like Garm mentioned, the activation time of open loop depends entirely on the ECU, it's unlikely the blitz controller can speed this up in any way...
Where it's confusing is that camelll believes in some conditions, there is a small window of time in between the supercharger activating and producing boost, and the ECU actually going into open loop mode and thus providing enough fuel. So, in that small window, there would actually be a lean condition of not enough fuel to go with the increased mass of air.
Unfortunately like Garm mentioned, the activation time of open loop depends entirely on the ECU, it's unlikely the blitz controller can speed this up in any way...
Q: could Blitz possibly increase this kit's amount of AWESOME???
A: after autocrossing it yesterday, I'm gonna say this adjustment is not necessary 😁
Not to make light of anyone's concerns, I'm just enjoying the hell out of the supercharger, with tinkering being approximately 33.3% of the fun.
A: after autocrossing it yesterday, I'm gonna say this adjustment is not necessary 😁
Not to make light of anyone's concerns, I'm just enjoying the hell out of the supercharger, with tinkering being approximately 33.3% of the fun.
that's right, make us atmospherically-challenged folks even more jealous, you evil woman 😁
😢 oh you hurt my feelinks
Not to nitpick, but you used a little "e" in that one word... don't you know by now my title is Mistress of Extraordinary Evil?
Not to nitpick, but you used a little "e" in that one word... don't you know by now my title is Mistress of Extraordinary Evil?
off topic
KK, will you make the Nashville Show by chance?
KK, will you make the Nashville Show by chance?
KK, please post another thread in the Racing forum about the autocrossing. I can't wait to read what you think about the response, especially coming out of a turn.Originally Posted by kurokoma-kun ↑Q: could Blitz possibly increase this kit's amount of AWESOME???
A: after autocrossing it yesterday, I'm gonna say this adjustment is not necessary 😁
to summarize:
from a standstill, open loop takes 5-8 seconds.
if moving (only at freeway speeds?), open loop happens instantly.
Does that sound like the ECU responding differently to the same signal? Or is the fuel controller capable of sending more than one signal to the ECU?
***Is the fuel controller wired into the ECU where it COULD control closed/open loop condition?
from a standstill, open loop takes 5-8 seconds.
if moving (only at freeway speeds?), open loop happens instantly.
Does that sound like the ECU responding differently to the same signal? Or is the fuel controller capable of sending more than one signal to the ECU?
***Is the fuel controller wired into the ECU where it COULD control closed/open loop condition?
I don't know CRAP about supercharged or turbocharged cars or cars in general but if you have a lean reading can't you just upgrade your fuel injectors to put more fuel into the engine? just a thought for all the supercharged guys out there. I don't think modding your intake will matter for that matter because the amount of air you get from a stock intake to a aftermarket intake doesn't really change THAT much to even give you a big difference (Unless you have the 1zz TB). Theoretically, the bigger pipe means more air but it still have to go through what ever TB size you have, an am intake only changed the rate at how fast the air gets to the TB from the intake inlet.... Thus the really little increase in horsepower(honestly like 1hp if anything). As far as CAI goes, it's generally the same as a regular intake except theoretically your putting in colder air since its from the bottom but honestly in my opinion on a hot day, you'll actually be sucking in much hotter air because the asphault would be hotter and all....
Yeah, you can add another injector but if you look at it like this. You have 4 injectors firing already and it reads a rich condition, it lowers injector latency to an adequate level to meet the stoich condition. Now if you just add an extra injector not hooked up to the ecu, the O2 sensor will still see it from the readings and even still adjust it. Or atleast thats what I am assuming as it reads off the O2 sensor?
And about it taking way too long to enter open loop from a standstill vs. on the highway, you have to understand that there is alot of criteria it has to meet before it triggers open loop. The main reason it probably comes on quick on the highway is probably that the engine is already under a susbstantial amount of load etc etc
And about it taking way too long to enter open loop from a standstill vs. on the highway, you have to understand that there is alot of criteria it has to meet before it triggers open loop. The main reason it probably comes on quick on the highway is probably that the engine is already under a susbstantial amount of load etc etc
Well, I've been reading peter's and noog's post about how they are getting lean condition and I just thought about the idea since I've been reading around and no one really bothered to upgrade their injectors lol just my 2 cents
Three important items the fuel controller is wired to are the accelerator pedal position sensor (VPA terminal on ECM), MAF (VG), and engine rpm sensors (terminal differs by controller model--this is camell's legendary mutant pink wire 😛), all of which (afaik) are used along with other sensors to determine when to trigger open/closed loop, among other things.Originally Posted by cali yaris ↑***Is the fuel controller wired into the ECU where it COULD control closed/open loop condition?
The ECM and fuel controller are obviously intended to act in concert somehow, but as for exactly how data is shared between them seems to be an open question at the moment... the ECM is no doubt still responsible for the actual functions of engine control, but does anyone here know for sure how it is "informed" of conditions by the fuel controller, and vice versa? Or is it only a one-way relationship, ECM --> fuel controller? Blitz must know, so since this thread is supposed to be gathering info for their use, I think we ask these questions only in the hope that they will get some insight into our concerns, if not to try to solve some things on our own.
As for my own car, when AFR goes rich and open loop is triggered does seem to vary according to engine rpm and load as well as throttle positon, at least. I've only noticed the two distinct two states under boost so far--what I guess I could call "town" and "highway"--all I'd like to know is if this is normal? Judging only by my own impressions of performance it certainly feels that way but based on what camell is asking I 🤷
well yeah if you put in larger injectors you might be able to fool the ecu a bit like the TC ones, its worth a shot. If it still thinks the yaris injectors are in there it will be dumping more fuel than necessary and confuse the ecu hopefully not triggering a CEL
worth a try hehe
When I am at a stoplight and floor it, it takes approximately 2 seconds for the police pursuit car to fly out from his place of concealment in the bushes! He appears immediately in my rearview mirror, and only takes a few minutes to nail me for a $280 ticket 🆘Originally Posted by camelll ↑KK when you are at a stop light and floor it how long does it take your car to go into open loop? Just watch your a/f gauge when it goes to 11-12 you are in open loop.
JUST KIDDING 😛 here's how it really goes:
If I go from standstill to wot, I am seeing 11s-12s AFR as soon as I hit 6-7-8 psi (my max). Typically this involves throttle position of 50 or higher, what I think of as "wot." However, this also happens if I reach those psi's at slightly lower throttle position, under heavy acceleration (merging into faster traffic while going up a hill, lets say).
Just a related note, not the wot situation: If I do not exceed 3-4 psi, my AFR may remain at 13-14-15 indefinitely, EXCEPT in "highway" mode as mentioned before.
This is based on so few tests though, I've only had those gauges in for a week, so I'll keep watching as closely as I can while avoiding getting arrested
I picked up a set of four used tC injectors at lunchtime today.🙂Originally Posted by gwasabi ↑Well, I've been reading peter's and noog's post about how they are getting lean condition and I just thought about the idea since I've been reading around and no one really bothered to upgrade their injectors lol just my 2 cents
They'll go on Friday. That'll give me a day and a half before I have to autox with them on Sunday.
You are seeing those AFR numbers sooner than camell and I. It isn't until we hit open loop till we see the 11-12. When you hit your 6-7-8 psi, is that when it is open loop? Did you check thatOriginally Posted by kurokoma-kun ↑
If I go from standstill to wot, I am seeing 11s-12s AFR as soon as I hit 6-7-8 psi (my max).
After watching for a week now it looks like the 11s-12s always go hand in hand with open loop on my car.
It does take a couple seconds or longer for the scangauge to show that, but it takes that long for it to show any change!... Garm was saying it's display is slow compared to our a/f and other gauges.
It does take a couple seconds or longer for the scangauge to show that, but it takes that long for it to show any change!... Garm was saying it's display is slow compared to our a/f and other gauges.
Mike, did you say that the fuel controller is connected to RPM? One difference is that when you are on the freeway, you are already up at around 2,000 RPM when you hit the gas for WOT.
When you're at a stop, unless you're doing some kind of launch control, you are at an idle of 700 or so.
This is just an observation.
When you're at a stop, unless you're doing some kind of launch control, you are at an idle of 700 or so.
This is just an observation.
From a standstill, if I mash the gas pedal, as I accelerate and build boost pressure, AFR goes to 11-12 as soon as I get to about 5 psi. How long that takes seems to depend on how long it takes to get to that boost level.
To be able to say what happens at "wot" (aka wide open throttle), I feel I must check the scangauge, as it is what shows me tps/throttle position.
This is why I say open loop seems to depend on boost (and maybe other things as well) rather than tps alone, because at certain times (punching it from a dead stop going up steep hill for example) as soon as I hit 5 psi AFR will go rich at a tps of 30, not what I would normally call wot.
Normally, at part-open throttle, and boost pressures of less than 4 psi... this is when I'm seeing 14s-15s.
The EXCEPTION to ALL of this is at ~65+ miles an hour, when it goes rich at 1 psi, again, regardless of throttle position.
But honestly y'all, wtf do i know? All statements are pure speculation on my part. It's an intricate system, and beyond the basics I haven't the faintest idea how it really works. All this reading and learning and discussion is fun, yet I sure do wish a real supercharger expert would step in and just tell us what's normal! My curiousity must be satisfied... I say we kidnap one of the Blitz engineers and make him talk! 😆
To be able to say what happens at "wot" (aka wide open throttle), I feel I must check the scangauge, as it is what shows me tps/throttle position.
This is why I say open loop seems to depend on boost (and maybe other things as well) rather than tps alone, because at certain times (punching it from a dead stop going up steep hill for example) as soon as I hit 5 psi AFR will go rich at a tps of 30, not what I would normally call wot.
Normally, at part-open throttle, and boost pressures of less than 4 psi... this is when I'm seeing 14s-15s.
The EXCEPTION to ALL of this is at ~65+ miles an hour, when it goes rich at 1 psi, again, regardless of throttle position.
But honestly y'all, wtf do i know? All statements are pure speculation on my part. It's an intricate system, and beyond the basics I haven't the faintest idea how it really works. All this reading and learning and discussion is fun, yet I sure do wish a real supercharger expert would step in and just tell us what's normal! My curiousity must be satisfied... I say we kidnap one of the Blitz engineers and make him talk! 😆
I have an AEM cai, the type with the filter in the fender. Stock MAF mounts in this in more or less stock position (oriented same direction in the pipe in other words)Originally Posted by camelll ↑What cai are you using? short ram or true cai?
Well and who knows, the fact that mine is manual and yours automatic may account for that difference. Or it may be that I just haven't studied mine long enough to be able to describe it accurately.Originally Posted by camelll ↑KK the only difference we have at this point is the amount of time it takes to go open loop from a stand still. Other than that we are spot on with other conditions and readings.
But yeah, since our cars are working so similar, though installed many months apart and with different style fuel controllers, I agree they seem to represent Blitz's target for "normal" operation. (i hope)
i know this has been covered before but whats the deal with the random vibrations i hear when my a/c is on? i turned it on for the first time yesterday and got the vibrations/noises
Whooppee, I don't think any of us know. We're all waiting for someone else to say that something fell off the car as a result of running the A/C.
any new news from blitz?
So, I was wondering, since I'm hoping to join the boosted crowd soon, what's the verdict on the air intake? Can I keep my AEM CAI or should I switch back to the stock airbox? Splicing or soldering?
Solder.
Spliced. It's held up for a year and a half now.
But I won't get any sympathy if a connection fails. 😛
But I won't get any sympathy if a connection fails. 😛
Hmm, I don't have a bypass filter, so I guess I have nothing to worry about there 🙄Originally Posted by echo_hrs ↑I had the AEM, I just removed the bypass filter and put a rubber coupler instead to eliminate the risk of the SC sucking it in...Soldering over splicing for sure...
Cheers