Yarisworld Archive

S/C owners: collecting information

151 posts · 33,597 views · page 2 of 4

Replies continued

PETERPOOPOahu · Apr 16, 2009#51
Originally Posted by cali yaris ↑
This does not mean they aren't working on the problem. It means they are eliminating possibilities. That is the appropriate process. They aren't going to send over fuel controllers (@ $700 a pop retail) with random maps, when they don't know what's been done or not done on our side.
I understand that. That is why i provided the info. However, it seems strange for them to say that noogie's AFR is fine and not give a reasoning for that (if they didn't). When most people know that his and my A/F readings are higher than ideal WOT AF numbers.

It seems I have done everything accordingly, yet still have the lean problem. I hope they can come up with something. *fingers crossed*

Anywho, I hope other people chime in with the info needed!
PETERPOOPOahu · Apr 17, 2009#52
*BUMP* Yo S/C guys, answer garm's new questions on the bottom of page 3. Thanks
cali yarisThread starterCanoga Park, CA · Apr 18, 2009#53
mouse, the megasquirt is not a standalone management, it's a fuel controller. However, it is tunable, so that gives it an advantage over a pre-programmed unit like the Blitz one.
whooppee777Maryland · Apr 18, 2009#54
i set a CEL code P0302, misfire in 2nd cylinder, last night at WOT in third gear
MouseMiami, Fl. · Apr 18, 2009#55
Then is the Hydra the same as the MS?
MouseMiami, Fl. · Apr 18, 2009#56
IDK...but a lot of people have said that you can use it as either a piggyback or as a full stand alone.
cali yarisThread starterCanoga Park, CA · Apr 18, 2009#57
The Hydra has full standalone capability (at least their Nemesis 2 does), including timing, peripherals (a/c, power steering, etc), and other functions. Much like the AEM EMS I'm using, or a MoTeC, etc.

MegaSquirt gives control over fuel only - the ECU is still doing most of the work to control the motor.
turboecho2005Ottawa, Ontario · Apr 18, 2009#59
Mouse is right... Megasquirt can be used as either a standalone or a piggyback. But you may lose the vvti... Unless someone has figured that out.

I used megasquirt as a piggy back on the 1nzfe and its a full standalone on the 4age.
kurokoma-kunmy own little world · Apr 20, 2009#60
Got some new info on AFR, I'll repeat the rest of the stuff as well. Looks like my experiences pretty much parallel camelll's.

Air Fuel Ratio:
* 11-12 range at wot in open loop (making up to 8 psi)
* mid 14s-low 15s in closed loop (both on and off boost)
* steady at 16 during DFCO (open loop)

Fuel Controller Wiring: Splice clips (the good kind, not the shit ones from the kit 😛 )
Spark Plug: NGK 7 heat range plugs
Pump Gas Quality: BP 93 octane plus lucas oil octane booster

I just got the wideband a/f gauge in over the weekend so I'll continue to keep an eye on it. Similar to what camelll said, I see a brief delay in going to open loop at wot, but I see the same delay when entering dfco, so it may simply be may be the scangauge catching up. My main desire would be to eliminate long-term use of the fuel additive to prevent knocking.
LtNoogieWest Hills, CA · Apr 20, 2009#61
KK, have you tried a tankful without the addditive? I believe that Yaris T-sport mentioned that he was able to stop using the octane booster. I don't understand why other than maybe the ECU was able to learn and adjust. Doesn't make sense to me.
kurokoma-kunmy own little world · Apr 20, 2009#62
Originally Posted by LtNoogie ↑
KK, have you tried a tankful without the addditive? I believe that Yaris T-sport mentioned that he was able to stop using the octane booster. I don't understand why other than maybe the ECU was able to learn and adjust. Doesn't make sense to me.
Yeah, I saw T-sport's comments and tried a tank without additive last week but the knocking returned. 👎

It runs so well with the octane booster I almost don't mind the added expense, but seeing what others have said about the long-term effect on spark plugs does concern me.
cali yarisThread starterCanoga Park, CA · Apr 20, 2009#63
Plus.... you shouldn't have to, in my opinion.
PETERPOOPOahu · Apr 20, 2009#64
Well wouldn't we have to because a few people were guessing the blitz kit was tuned to 100 octane in Japan? And if that is true, it comes out to like 95-96 octane in the US?
cali yarisThread starterCanoga Park, CA · Apr 20, 2009#65
I was thinking the same thing, but Blitz confirmed that they used a USDM car (here in the USA) to install and test their system. I doubt that car had more than 91 in it when they did their R&D here.

I'm emailing them again today to find out what's up.
PETERPOOPOahu · Apr 21, 2009#66
Originally Posted by kurokoma-kun ↑
Got some new info on AFR, I'll repeat the rest of the stuff as well. Looks like my experiences pretty much parallel camelll's.

Air Fuel Ratio:
* 11-12 range at wot in open loop (making up to 8 psi)
* mid 14s-low 15s in closed loop (both on and off boost)
* steady at 16 during DFCO (open loop)
What is your guys IGN timing during your WOT (11-12 AFR)? And IGN timing during your MID 14s-15s in closed loop with boost on and off.

Thanks
LtNoogieWest Hills, CA · Apr 21, 2009#67
With my limited understanding of engine performance, I thought that when you retard to single digits on timing, you are delaying when the spark occurs to near top dead center. That helps to prevent pre-ignition but also outputs less power than if you had ignited earlier... meaning double digit ignition retardation. Earlier ignition allows for more of the fuel to completely burn.

Someone with more knowledge please chime in.
LtNoogieWest Hills, CA · Apr 21, 2009#68
I am going to try larger injectors next. I have to read up on why more fuel prevents pre-ignition.
kurokoma-kunmy own little world · Apr 21, 2009#69
My ignition timing:
at idle ~5
out of boost ~30 (AFR 14s-15s)
under low boost ~15 (AFR 14s-15s)
at wot ~10, rarely + briefly single digits (AFR 11s-12s)

Originally Posted by camelll ↑
KK do you have shell gas stations with 93? I have used that multiple tanks without octane booster and no knocking. I cannot get bp 93 as they don't have it here but bp 91 knocks like crazy without octane booster.
Well, BP near me are calling what they have 93 octane 🙄 though sometimes I suspect we are all getting crap gas! Seems like lately I've read more posts about stalling and poor performance in other parts of the board than ever before. Hell I dunno </conspiracy theory> Annnnyway, have not tried Shell, I'll have to see if I can find it!
eTiMaGoBangkok, Thailand · Apr 21, 2009#70
you could also look into water/meth injection as a way too cool down the compressed air, though I'm not sure where you'd be able to fit the nozzle!
LtNoogieWest Hills, CA · Apr 21, 2009#71
AlexNet0 is fabricating a throttle body spacer with a NOS injection port. Perhaps the water/meth can be injected there. That is way low on my list of mods, though.
eTiMaGoBangkok, Thailand · Apr 21, 2009#72
yeah but inejcting it before the compression takes place, I'm not sure how efficient it'll be? I mean, you basically want the liquid mist to absorb heat (thus cooling the air) and turn to steam...
LtNoogieWest Hills, CA · Apr 21, 2009#73
It still has the effect of cooling the intake air charge. You start cooler so your compressed charge is cooler. Here's an interesting article on a homemade water injection system.

http://www.dave-cushman.net/misc/mannject.html
eTiMaGoBangkok, Thailand · Apr 21, 2009#74
Originally Posted by LtNoogie ↑
It still has the effect of cooling the intake air charge. You start cooler so your compressed charge is cooler. Here's an interesting article on a homemade water injection system.

http://www.dave-cushman.net/misc/mannject.html
very most interesting! Basically on our engines that's be using the vacuum line from the PCV system or brake booster, but the only problem I can think off, at full throttle, you don't have much of a vacuum, so there won't be so much flow through the tube and the water injection would be greatly reduced when you would actually want it most... So really I think you'd want to have a small aquarium pump or something to ensure a steady flow...
Nexus1155Dorchester · Apr 21, 2009#75
30 degrees of ignition out of boost? and thats where the problem exits, your probably misfiring and knocking. I don't think you should be hitting those high of values like that...

I'm only running around 20-23 where it would be out of boost if i was on a yaris and this is on a 4.2L truck that can take a few more degrees.

http://i39.tinypic.com/vx0l6x.jpg
PETERPOOPOahu · Apr 21, 2009#76
Originally Posted by kurokoma-kun ↑
My ignition timing:
at idle ~5
out of boost ~30 (AFR 14s-15s)
under low boost ~15 (AFR 14s-15s)
at wot ~10, rarely + briefly single digits (AFR 11s-12s)

Originally Posted by camelll ↑
I see single digits on timing anytime under boost regardless of a/f ratio. The only time I see above single digits is out of boost. If I am above single digits during boost it is real low teens. Out of boost and normal driving I see 30's + on timing and without boost getting on it I see high teens to low 20's.
Max boost is 8.

my IGN is 17 under WOT with AFR of 13-14
my IGN is 25-30 w/ NO boost & normal driving w/ AFR of 14.5-15.1
My IGN is 15 when under low boost and AFR is 14.5-15.1
My IGN is 5 when coasting/neutral with AFR of 15

*All of my numbers of IGN and AFR seem to match with your guys, besides my IGN under WOT. I am seeing 17 IGN timing and not the low teens like you guys..

Is that safe? Is that why I am generating "more" power?

Here's a link to a thread I made about it last night with a video clip of my gauge readings from above..

NEW VIDEO: Wideband/Boost readings.
PETERPOOPOahu · Apr 23, 2009#77
Well I put my stock airbox on, and I'm getting readings of 11-12 at WOT (during open loop). You hear that Noogie?

However, this is only at Open loop. Open loop takes a few to open once I initially hit the gass hard. So during that time I am running hard and it's not open loop yet, I am still seeing numbers of 14-15. However, once in Open loop, I saw 11-12. My IGN timing was still at 17. Not low teens like everyone else said they were getting. So are those proper numbers oppossed to other people now because I am running that IGN timing with 11-12 AFR? Is it safe to have 17 IGN timing now that I am getting 11-12 during open loop?

No time to do driving tonight (homework), but tomorrow I will get more numbers.
Nexus1155Dorchester · Apr 23, 2009#78
wellll more fuel will counter act high spark, but just by putting the stock airbox you limited the air that much to change the AFR by 2 points? These cars are screwy as helllll. Go drive some more and bring back some more data lol...
cali yarisThread starterCanoga Park, CA · Apr 23, 2009#79
^ I think he's onto something. Looks like MAYBE the intake set up makes a difference with respect to the tune that Blitz intended.
PETERPOOPOahu · Apr 23, 2009#80
The stock airbox DEFINATELY made a change in my AFR and I guess it's a testament of how much air the aFe intake really takes in. I am curious to know what intakes each blitz owner is using. It's hard to believe that the aFe intake would make so much of a difference compared to other aftermarket intakes. However, the numbers don't lie.

I hope noogie is inspired to swap back to his stock airbox too, and we can confirm this.

Definately will have more of a variety of A/F readings in the next couple of days.
LtNoogieWest Hills, CA · Apr 23, 2009#81
I guess this is where iterative tweeking and dyno testing is the right way to tune if one could afford it. Bringing the AFR back to a safe range is not the end goal. The end goal should be to maximize power while staying in a safe operating zone.

Peter is enrichening his mixture at WOT by limiting airflow slightly. Peter, what was your ignition timing under WOT before you put on the stock airbox? If timing was lower than 17, you may have increased your power while at the same time moved yourself into a safer zone. If you can get your WOT AFR into the 11 - 13 range, your dyno guys shouldn't be afraid to give you your last two dyno pulls.

I am going to try the opposite tack. In order to enrichen my mixture at WOT, I am going to try to dump more fuel into the charge by trying larger injectors (thanks Garm). I'm trying to collect as much data as I can with my logger before changing to the larger injectors.

It's really cool that we have enough S/C'd owners that we can try different approaches.
PETERPOOPOahu · Apr 23, 2009#82
Originally Posted by LtNoogie ↑
Peter is enrichening his mixture at WOT by limiting airflow slightly. Peter, what was your ignition timing under WOT before you put on the stock airbox? If timing was lower than 17, you may have increased your power while at the same time moved yourself into a safer zone. If you can get your WOT AFR into the 11 - 13 range, your dyno guys shouldn't be afraid to give you your last two dyno pulls.

Like I said in my update post (like 4 posts before this), my IGN timing is the same now as it was with the aFe intake at WOT. My IGN timing is 17 at WOT (open loop) now and it was 17 with the aFe. The only difference now is that I have 11-12 AFR with the stock airbox, and when I had the aFe on, I had 13-14 AFR.

I'm still not sure if I am any safer now even though I have 11-12 AFR, but still the 17 IGN timing. Anyone know? Because the majority of the blitz owners who run 11-12 AFR, have low teens or single digit IGN numbers. However, I do not.

Originally Posted by LtNoogie ↑

If you can get your WOT AFR into the 11 - 13 range, your dyno guys shouldn't be afraid to give you your last two dyno pulls.
IT IS in the 11-12 range. That's the reason for my update. However, my question was, is it ok if I am running 17 IGN timing with the 11-12 AFR.

Originally Posted by LtNoogie ↑
Bringing the AFR back to a safe range is not the end goal. The end goal should be to maximize power while staying in a safe operating zone.
For now, it is for me. However, I can promise I will eventually get the greddy emanage ultimate/larger injectors/larger throttle body/aFe intake and tune it accordingly for maximum HP with ideal AFR.
TOUGEghostKauai · Apr 23, 2009#83
Those new AFR numbers with the stock intake look much better. Is that 17* peak? What does the whole timing curve look like? It may be the best you can do anyway until you have a way to actually make adjustments to the fuel and timing maps (e-mangae, injectors, etc. like you mentioned). I know a 4G63 isn't the same engine but the tuning principles are similar; I run 21* peak timing WOT open loop at full boost with a target AFR of about 11.1
PETERPOOPOahu · Apr 23, 2009#84
The 17 is not peak. I think it might go to 18-19 too. Well from your response, I'll take it that the 17 IGN timing area is safe and actually good!

I believe it's not possible to adjust IGN timing. Not sure though...

More numbers coming tomorrow!
TOUGEghostKauai · Apr 23, 2009#85
If it runs smooth and doesn't knock, it should be ok. I usually advance timing 1* at a time until the power curve flattens out or I start to get knock.
Nexus1155Dorchester · Apr 23, 2009#86
Question... did the blitz install say to change out the air intake? I mean you have to consider the ecu senses air coming into the engine and tries to compensate for it...

Its like trying to suck air in through your mouth or air in through a straw..... One has a large area to gather in volume and one has only a small hole.....

For whoever is getting crap AFR on your blitz kit, i urge you to try what Peter did, 11-12 is ideal for a SC and fueling(safe) i doubt hell have any more problems if this is the case...
LtNoogieWest Hills, CA · Apr 23, 2009#87
I could probably approximate a stock air box by taping off part of my aFe filter. That's a quick and dirty way of limiting airflow without doing the whole airbox thing.
kurokoma-kunmy own little world · Apr 23, 2009#88
I'm not seeing the lean condition, I only had the knocking issue.

My intake/exhaust system starts with AEM cai, then header, midpipe, axleback. I guess this is why my results are different 🤷
kurokoma-kunmy own little world · Apr 23, 2009#89
My AFR is 13-15 under boost (closed loop), 11s-12s at wot (open loop)
kurokoma-kunmy own little world · Apr 23, 2009#90
I see what you mean. But I guess as I've gone full throttle I've been focusing on the a/f gauge rather than the scangauge, and not seeing anything to indicate lean condition as it transitions to open loop... 🤷

Could it just be the scangauge lagging behind? For example when I take my foot off the gas, it takes at least a couple seconds before showing open loop for DFCO.

Guess I really need to take some videos too, its too many gauges to study in detail while driving
kurokoma-kunmy own little world · Apr 23, 2009#91
Hmmmm thats weird, my a/f gauge shows nothing but "green" at low boost... from this I've been assuming it's seeking to maintain stoich numbers until you get to wot/open loop. Also I was under the impression that at wot an AFR of 11--which would under any other conditions be rich--is actually ok... 🤷
cali yarisThread starterCanoga Park, CA · Apr 23, 2009#92
11 is fine under boost.

The scangauge does lag ever so slightly.
More than slightly, IMO. The scangauge is really slow, OBDII is really not useful for real-time data that changes rapidly.
PETERPOOPOahu · Apr 23, 2009#93
Well even if the scangauge is lagging to go into open loop; like cammell said, just look at your boost gauge once you are in boost. If your numbers aren't 11-12, then you are lean. So it shouldn't matter if the scanguage is lagging to go into open loop, because your wideband and boost gauge are instant.

Well I am glad to hear that camell and KK are both only getting 11-12 when in open loop. Atleast I am up to page with the "normal" blitz guys.

I gotta go driving to class in a few, so I will be collecting numbers and will post later today.


* I wish the other blitz owners were active in this thread.....
PETERPOOPOahu · Apr 23, 2009#94
Drove around more today. Constant 11.9-12.1 AFR with 16-17 IGN timing when in open loop. Idle of 15 AFR with single digit IGN. Also in DFCO i get 15 AFR. Open loop needs to happen sooner. I don't not like seeing the 11-12 AFR until open loop. I'd like to see it sooner, especially when I engage WOT.
LtNoogieWest Hills, CA · Apr 24, 2009#95
My ghetto air restriction testing. Rather than change back to the old airbox, I am testing different amount of airflow by adding more tape. I collected some data on the data logger and am analyzing it tonight.

Picture not included in this copy
PETERPOOPOahu · Apr 24, 2009#96
lol. ghetto R&D. nice
Nexus1155Dorchester · Apr 24, 2009#97
The even funnier thing is is that if the tape isn't super pourous it will work!! hahaha
LtNoogieWest Hills, CA · Apr 24, 2009#98
I haven't seen my airbox since the car was a few weeks old. Does anyone know what is the size of the air inlet to the box? Is is something easily measurable?
yaris-meAnaheim, CA · Apr 24, 2009#99
Just PMed. Had to leave the warmth of my apartment.🙁
LtNoogieWest Hills, CA · Apr 24, 2009#100
Thanks for sacrificing for the team. I was just told that the opening to the stock airbox is 2" in diameter. That seems awfully small when you look at these big-ass cone low-restriction intake filters but it made me think some more.

Performance will be limited to the smallest restriction if air speed is equal. The smallest restriction is either the stock airbox inlet or the diameter of the stock throttle body.

Does anyone have the diameter of the stock throttle body opening. I'm sure if I searched, I would find it in another thread but maybe one of you have it handy.

It looks like I need alot more blue tape this afternoon. No wonder there was very little effect with the amount of tape I put on the filter.