Yarisworld Archive

need help: foglight indicator - where are the wires?

77 posts · 63,173 views · page 2 of 2

Replies continued

jcboyAsia · Jan 24, 2013#51
Thanks scott. Well, I did what you said, unfortunately it is sooooo hard to see the cluster lights since the gauge face is practically opaque even if light is shone on it. I would like to take a look at tom under a strong sun though--although i think (i hope im right) that i saw a fog and a rear fog symbol on the right side, roughly above the lcd display of the gauge.

If I do, then what's the next move for me as far as the simpler D2 12V wiring goes? I don't want to modify the foglight wiring as bold as the one in the thread Yarisugi posted a link for, as i'm afraid that if and when I would claim electrical warranty, it can easily be seen by the service guy.
CTScottUSA, CT · Jan 24, 2013#52
Originally Posted by jcboy ↑
Thanks scott. Well, I did what you said, unfortunately it is sooooo hard to see the cluster lights since the gauge face is practically opaque even if light is shone on it. I would like to take a look at tom under a strong sun though--although i think (i hope im right) that i saw a fog and a rear fog symbol on the right side, roughly above the lcd display of the gauge.

If I do, then what's the next move for me as far as the simpler D2 12V wiring goes? I don't want to modify the foglight wiring as bold as the one in the thread Yarisugi posted a link for, as i'm afraid that if and when I would claim electrical warranty, it can easily be seen by the service guy.


I wound need to see the wires on the two connectors at the base of your instrument cluster to determine if the wiring matches the wiring diagrams that I have.
jcboyAsia · Jan 25, 2013#53
Ok i do i have a fog light indicator and even the rearfog! If my assumptions are correct, then it should be the same wiring but ill take a screenshot of it and post it here tom as its already night here and the flash or fluorescent lights will mess up the hues let alone the colors of the wires.

Thanks!
jcboyAsia · Jan 26, 2013#54
Hey scott. Here you go. Havent tried anything as im scared to fry something. Or would i? Other than a fuse i mean, if i connected one of the pins to 12v.


Picture not included in this copy


Picture not included in this copy
CTScottUSA, CT · Jan 26, 2013#55
Originally Posted by kosy_m ↑
Intrestingly in the asian right hand drive vitz , you have to connect 12 v to the top row 2 nd pin of D2 to fire the indicator.🙂
That is actually the same pin. In the connector diagram that I posted on page 3 of this thread, the pin numbers are looking into the pin holes of the connector, not into the wire entry side.

Picture not included in this copy
CTScottUSA, CT · Jan 26, 2013#56
Originally Posted by jcboy ↑
Hey scott. Here you go. Havent tried anything as im scared to fry something. Or would i? Other than a fuse i mean, if i connected one of the pins to 12v.


Picture not included in this copy


Picture not included in this copy

The worst case is a blown fuse, but I think it will work fine. The Yellow wire on your connector is the one to connect to. I just tested it on a Japanese cluster that I have and that pin lit the front fog light LED.
yarisugiThread starterハワイ · Jan 26, 2013#57
You sure got a lot of clusters CTScott. 🙂
CTScottUSA, CT · Jan 26, 2013#58
Originally Posted by yarisugi ↑
You sure got a lot of clusters CTScott. 🙂
Looking around my office I see Seven (plus there is one in each of my 3 Yaris). I think I have a problem and my someday appear on one of those reality shows about hoarders.
jcboyAsia · Jan 27, 2013#59
😁
Originally Posted by CTScott ↑
Looking around my office I see Seven (plus there is one in each of my 3 Yaris). I think I have a problem and my someday appear on one of those reality shows about hoarders.
haha I would think so too, so be ready with your own show.lol

ok thanks, i am hopeful it is the correct one, because i just tested it from each of the two green wires from the switch as well as the blue (esuse), and nothing happened.

i am hopeful because I am unsure that the clusters here are made in Japan. We have our own Sta. Rosa, Laguna plant, and at best I would assume we import those from Thailand (due to costs).

if the green/blue wires are not a good source of 12V, do you think I should get a live 12V line from the battery terminal directly? and if that works, then you know how my next question goes, where do i get that 12V from?

TIA Scott, youve been always very helpful, and I can still recall the days when I kept bugging you for the correct wiring of the passenger door lock switch. 👍
CTScottUSA, CT · Jan 27, 2013#60
Originally Posted by jcboy ↑
😁

haha I would think so too, so be ready with your own show.lol

ok thanks, i am hopeful it is the correct one, because i just tested it from each of the two green wires from the switch as well as the blue (esuse), and nothing happened.

i am hopeful because I am unsure that the clusters here are made in Japan. We have our own Sta. Rosa, Laguna plant, and at best I would assume we import those from Thailand (due to costs).

if the green/blue wires are not a good source of 12V, do you think I should get a live 12V line from the battery terminal directly? and if that works, then you know how my next question goes, where do i get that 12V from?

TIA Scott, youve been always very helpful, and I can still recall the days when I kept bugging you for the correct wiring of the passenger door lock switch. 👍
You will either need to measure the switch wires with a volt meter to see which one goes from 0 to 12 volts when the switch is pressed (if any actually does) or you can connect to the wire on the other side of the relay, which actually brings the 12 volts to the fog light bulbs.
jcboyAsia · Jan 27, 2013#61
Originally Posted by CTScott ↑
You will either need to measure the switch wires with a volt meter to see which one goes from 0 to 12 volts when the switch is pressed (if any actually does) or you can connect to the wire on the other side of the relay, which actually brings the 12 volts to the fog light bulbs.
ok i did what you said, and connected the yellow wire, D2-7, and i also measured the blue wire on the fog switch, it actually gives 12V to when foglights get switched on. it didnt work. both the green wires gave 12V when the park light switch was turned on, it also didnt work in firing up the foglight indicator on the gauge. 😢 is it possible to have indicators in the cluster but no LED for that? 🙁

BTW, the factory-wired esuse foglamp was included in the harness.😠 the wires the arrow point to come from the switch and are attached to the harness (thick one, in the middle) and somehow finds it way toward the relay (blue Denso relay on the right side, encircled) and also to the outside fusebox (probably)/engine bay, so there's really no route for me toward the esuse fog light install instructions.🙁

FYI, the items on the relays, etc, either say Denso Made in Japan or Denso Made in Thailand. So it gets even worse knowing my VIN tag says Made in Philippines. Now we dont know if the wiring follows the other Toyota plants and which one if it does.. 🤷 Help...😕

Picture not included in this copy
CTScottUSA, CT · Jan 27, 2013#62
Originally Posted by jcboy ↑
ok i did what you said, and connected the yellow wire, D2-7, and i also measured the blue wire on the fog switch, it actually gives 12V to when foglights get switched on. it didnt work. both the green wires gave 12V when the park light switch was turned on, it also didnt work in firing up the foglight indicator on the gauge. 😢 is it possible to have indicators in the cluster but no LED for that? 🙁

BTW, the factory-wired esuse foglamp was included in the harness.😠 the wires the arrow point to come from the switch and are attached to the harness (thick one, in the middle) and somehow finds it way toward the relay (blue Denso relay on the right side, encircled) and also to the outside fusebox (probably)/engine bay, so there's really no route for me toward the esuse fog light install instructions.🙁

FYI, the items on the relays, etc, either say Denso Made in Japan or Denso Made in Thailand. So it gets even worse knowing my VIN tag says Made in Philippines. Now we dont know if the wiring follows the other Toyota plants and which one if it does.. 🤷 Help...😕
That is interesting that the Esuse fogs are actually wired through the OEM fog wiring, rather than with the Esuse aftermarket harness. The presence of the blue relay on the right tells me that the foglight indicator is already hooked up, so it does appear that it is not active on your cluster.
jcboyAsia · Jan 28, 2013#63
is that slot on the right actually an OEM slot, or is it more of an empty slot that will serve as a holder for a relay (if ever a dealer needed to put one for some reason)? i asked bec i believe the wires don't actually go to any port on any junction box, rather just wires that are attached to the harness that go out into the outside fuse box. I'll take a picture of the fuse box and post it here, maybe you can get ideas. (crossed fingers...)

can i test it with, say, the D4-3 and D4-4 pins by any chance?
CTScottUSA, CT · Jan 28, 2013#64
Originally Posted by jcboy ↑
is that slot on the right actually an OEM slot, or is it more of an empty slot that will serve as a holder for a relay (if ever a dealer needed to put one for some reason)? i asked bec i believe the wires don't actually go to any port on any junction box, rather just wires that are attached to the harness that go out into the outside fuse box. I'll take a picture of the fuse box and post it here, maybe you can get ideas. (crossed fingers...)

can i test it with, say, the D4-3 and D4-4 pins by any chance?
That is the OEM fog light relay socket, even thought it seems like an after thought. The wires from it go into the harness, rather than into the body ECU.

At this point, I would suggest taking your cluster out (those two connectors and two screws), removing the two screws on the back that hold the tapered black part to the white part, and then you can lift up the plastic card and take a peek underneath to see if there is an LED under the fog indicator.
jcboyAsia · Jan 28, 2013#65
Ok thanks thats what i did earlier, but i unscrewed the 9 or 11 screws instead, trying to find out the same thing--that didnt take me anywhere haha. Ok i will try what you said later, but that wouldnt make the needle have to come off now, would it?i was scared about that, thats why i opted the former to try to make the back come off.
CTScottUSA, CT · Jan 28, 2013#66
Originally Posted by jcboy ↑
Ok thanks thats what i did earlier, but i unscrewed the 9 or 11 screws instead, trying to find out the same thing--that didnt take me anywhere haha. Ok i will try what you said later, but that wouldnt make the needle have to come off now, would it?i was scared about that, thats why i opted the former to try to make the back come off.
Here's what I mean. You don't need to pull the needles to look. I have the symbol lit in the picture, but you can just lift the plastic card to see if there is an LED under it or if there is an empty area of white plastic.

Picture not included in this copy

1 attachment not included in this copy

jcboyAsia · Jan 29, 2013#67
You never cease to amaze me scott. Yes it doesnt have the led on the slot. There are soldering leads on there,but the led isnt. I guess my next step is to try an ordinary led tap (long legs) since the hole is pretty deep. If it works without any wire tap then i guess it is indeed wired already, however, i dont have any options insofar as soldering an led there without removing the needles to remove the face, do i?
jcboyAsia · Jan 29, 2013#68
Ok i did everything, tap D2-7 with 12v, not tap with 12v, put led normally, led in reverse (just to be sure) and no the soldering leads dont seem to give current. Do you think the gauges here are wired differently? Well the lock unlock wires seemed to be in the same slot before..

I guess it ends here for me. 🤷 Thanks for all the help. 😎

My next best bet would be to get a local optitron gauge and hopefully make it work. Or get a usdm gauge hoping it has the same wiring.
jcboyAsia · Jan 29, 2013#69
Originally Posted by CTScott ↑
Here's what I mean. You don't need to pull the needles to look. I have the symbol lit in the picture, but you can just lift the plastic card to see if there is an LED under it or if there is an empty area of white plastic.

Attachment 49671
Thats a nice looking gauge btw. That LHD and optitron? 😁
CTScottUSA, CT · Jan 29, 2013#70
Originally Posted by jcboy ↑
Thats a nice looking gauge btw. That LHD and optitron? 😁
That's actually a RHD one.
NJ DriveNorthern NJ · Feb 3, 2013#71
Anybody know the weight of the fog lights? Unsure if the 2012s are any different than the previous gen, but a roundabout weight would suffice.
CTScottUSA, CT · Feb 3, 2013#72
Originally Posted by NJ Drive ↑
Anybody know the weight of the fog lights? Unsure if the 2012s are any different than the previous gen, but a roundabout weight would suffice.
OEM ones are 10.5 oz each, aftermarket ones are a bit less.
NJ DriveNorthern NJ · Feb 3, 2013#73
That's pretty light, guess they're staying in, lol. Thanks Scott.
BilliamUSA · Feb 1, 2020#74
Old thread revival.

A few months ago I installed some aftermarket fog lights on my daughter's 2010 LB. I wired them up to be DRLs. They come on and off automatically with the ignition. I installed a switch to the left of the steering wheel in case there was a need to turn them off. However my daughter occasionally turns them off by accident. So I figured I would come up with a way to use the OEM indicator light so she could easily tell if they were on. This thread made it easy.
CaptamricaSt. Louis Missouri · Aug 16, 2021#75
History, background and why I'm here.

I installed OEM Fog lights in my Daughter's White 2010 3 door hatchback and it was a total no brainer. The kit came with the switch that dropped right in one of the blanked out spots in the center near park brake with her Power lock switch and AUX Jack. The loom was there for the switch. The plugs were there for the fog lights. It went great.

Well that car took a hit from a Tractor trailer with my wife driving with her (daughter) in the passenger seat. Dude fell asleep at 75mph and drifted into the left lane with them almost past him. My wife floored it and almost got past him driving with 2 wheels in the grass median, blowing the horn, right next to the drivers door of the rig. Wasn't enough his front wheel caught them just behind the passenger door in front of the right rear wheel. His lug nuts opened up the car like a can opener. Blew out the passenger door window, it was tinted so it held together.

Spun them around in front of the truck sideways snow plowing them down the highway at 70mph. Guess he woke up somewhere in there and stopped the truck after about 1/4 mile.

My little girl is very timid but she loved that car, her first. She climbed out through the drivers door after my wife got out and took off running at the guy as he got out of his truck chasing him back up in his truck. She was going to kick his ass. My wife told me she couldn't believe they were still alive let alone seeing her picking a fight with a trucker.

Okay long story, sorry. I wasn't a fan of her vehicle choice when she picked out this used 2010 Yaris, never even heard of these before, but I couldn't knock it. It was sound aside from smelling like coffee. I stripped the interior and pressure washed the carpet and seat covers. I do all my own work on my vehicles. Just retired my 1993 Ford Explorer with 535,xxx miles. That's one of 3 that are over 400,000 miles. So I'm doing something right.

When she wanted another Yaris, I said no problem.
She picked out a Red 2013 Yaris LE 5 door hatchback. I'm doing all sorts of work on it for her underbody lighting, indirect LED lighting inside, etc. Plus installing Fog lights. Now this one is missing the interior loom but I have a kit to install it in the same place as it was in the 2010. I'm assuming the "Stalk" switch is the multifunction switch on the turn signal arm. I see the indicator in the instrument cluster. The plugs were outside for the fog lights themselves.

There is so much info here that I'm a little overwhelmed on which would apply to this 2013. A lot of this is Pre-2013 and I know there's a lot of changes just from the 2010 to the 2013, not for the better if you ask me, her to, she misses her 2010.

Just looking for confirmation of the pin assignments are the same and where to connect the switch to. I've got to pull power and ground from somewhere. The switch kit has all these wires for that but where am i pulling these from and where is the output to the fog light relay.

I'm going to dig back through and see what I can find but if anyone has anything to add I'd appreciate it.

Yeah, I'm a little long winded as well. Thanks
CaptamricaSt. Louis Missouri · Aug 16, 2021#76
I can't read the text in the images that defines the modules in the schematics. and what is a "Combination meter" that your hooking things up to when wiring it with the external relay. My kit has it's own relay but I'd like to use as much of the factory stuff as possible. Also need locations of where this relay would be at in a 2013. Her owners manual identifies the fuse but not the relay location.

Sorry if I sound like an idiot. I'm in the US and I discovered with the 2010 this vehicle is very popular outside the US especially in RHD countries.

Thanks
CaptamricaSt. Louis Missouri · Aug 17, 2021#77
Is the Combination meter the IP cluster? IP= Instrument Panel There's a lot of acronyms that are used in the thread that I am not familiar with. Sorry I was raised building Ford Aerostar and Explorer from 1988-2006. My daughter buying a Toyota was the first time anything other than a Ford, Mercury, or Lincoln had been in my garage.

Well, I did have a 1999 Plymouth Breeze someone gave me that came out of Michigan. It was my tetanus car. The Rockers were completely rusted out with jagged edges. If you were wearing shorts getting in and out you were bleeding. Used for a work car