personal opinion.. Yaris looks alot better.Originally Posted by thebarber ↑Yaris is 300lbs lighter, though
Yaris Motor Swap Thread *Read before posting swap threads*
218 posts · 914,851 views · page 3 of 5
Replies continued
I'm not going to argue semantics but even if you did build your own T Sport you're still gaining close to 200 lbs and if I'm going to go through the hassle of a motor swap which I'm forced to gain weight Id rather do it for more than a 22 hp bump is all I'm saying.
And yes I don't like the look of the XD either.
And yes I don't like the look of the XD either.
how are you gaining 200lbs? the engine weighs about 40lbs more than a 1nzfeOriginally Posted by xnamerxx ↑I'm not going to argue semantics but even if you did build your own T Sport you're still gaining close to 200 lbs and if I'm going to go through the hassle of a motor swap which I'm forced to gain weight Id rather do it for more than a 22 hp bump is all I'm saying.
And yes I don't like the look of the XD either.
you gain as much weight as you do adding a blitz supercharger kit...i weighed mine when i had it.
intake/header/exhaust ive been seeing about 145whp/140wtq on corolla's...thats on 87 octane and on an oem ecu
i ran 135whp/130wtq with i/h/e and 91 octance on my yaris...
im not saying that an engine swap would be easy...it won't be. but oem reliable power is a plus in my books
I was using the T sport as reference which weighs about 180lbs more than the standard car.
What corollas are you seeing that make 145 hp on 87 octane? I don't think I've seen a single corolla not powered by a 2zz make anywhere near that much power N/A but excluding that its still only 20 hp more and your adding weight in the worse possible place in front of the axle. I'm not saying a superchargers better but its substantially cheaper. Hell my competitor with a 1zz corolla didn't even break 125 and he built it to the limit of the rules.
If you take into account the cost of getting the ECU, Transmission, Engine, Axles, and accessories pus the time it takes to swap it it just doesn't feel like its worth it for such small gains.
If your dead set on swapping a motor getting the 2zz swapped would be a much better choice as the gains make sense plus the motor is far less limited than the 1zr and 1zz.
What corollas are you seeing that make 145 hp on 87 octane? I don't think I've seen a single corolla not powered by a 2zz make anywhere near that much power N/A but excluding that its still only 20 hp more and your adding weight in the worse possible place in front of the axle. I'm not saying a superchargers better but its substantially cheaper. Hell my competitor with a 1zz corolla didn't even break 125 and he built it to the limit of the rules.
If you take into account the cost of getting the ECU, Transmission, Engine, Axles, and accessories pus the time it takes to swap it it just doesn't feel like its worth it for such small gains.
If your dead set on swapping a motor getting the 2zz swapped would be a much better choice as the gains make sense plus the motor is far less limited than the 1zr and 1zz.
2zrfre corollas on corolla9.com have been making it....if i recall correctly
castrex, a member on this board with a TS, pulled the dyno below
40lbs isnt THAT much to add to the front, and you'll be adding that with a supercharger and at least that with a turbo/intercooler setup
n/a 1zz's ive seen will top out about 140whp with cam's....and the cams really suck at low rpms
2zz is a great engine, but only really with the c60. the transmission case is longer than the engine bay is wide in the yaris, so you'll need to notch the frame for it to fit. can be done, but its not typically an in-your-driveway swap.
what im saying, is that since the 2zrfe is available and, in theory, bolts up to a standard yaris transmission, its a decent option for oem-reliable power (in my opinion). a "new" supercharger kit, if you can find it, are about $3200-3400, used about $2000. i still think the 2zrfe swap could be done for $1500-2000 if you can DIY
im still keeping watch for a yaris cheap enough for me to attempt an engine swap
castrex dyno
Picture not included in this copy
castrex, a member on this board with a TS, pulled the dyno below
40lbs isnt THAT much to add to the front, and you'll be adding that with a supercharger and at least that with a turbo/intercooler setup
n/a 1zz's ive seen will top out about 140whp with cam's....and the cams really suck at low rpms
2zz is a great engine, but only really with the c60. the transmission case is longer than the engine bay is wide in the yaris, so you'll need to notch the frame for it to fit. can be done, but its not typically an in-your-driveway swap.
what im saying, is that since the 2zrfe is available and, in theory, bolts up to a standard yaris transmission, its a decent option for oem-reliable power (in my opinion). a "new" supercharger kit, if you can find it, are about $3200-3400, used about $2000. i still think the 2zrfe swap could be done for $1500-2000 if you can DIY
im still keeping watch for a yaris cheap enough for me to attempt an engine swap
castrex dyno
Picture not included in this copy
I've seen that dyno float around many times and its always associated with RichardHoldener but basically its a custom intake manifold, intake, long tube, and race exhaust which adds a considerable amount of cost to the project plus those parts don't exist and no one has been able to duplicate them so I don't believe its real. Most of the dynos fall in the low 120's to low 130's with high 110's being the norm for stock. I'm just saying 140's are unlikely to be seen from a 2zr swap.
40lbs is quite a bit of weight to add for 20hp but even so you still need an all the supporting parts to make it work plus its such a small gain I don't think its worth the effort.
I don't see what the issue with the c50 transmission is, for a higher powered engine the gear ratio's aren't terrible you just need to get a better final drive but that's not even that big of an issue since the weight gain is 80 lbs total for an extra almost 80 hp plus you also have room to grow and the engine has way better aftermarket support whereas the 2zr does not. The only reason I can see someone going with the 2zr is if they wan't to remain CARB compliant in which case I'd just sell the car and buy something else because it would be far easier and less of a hassle to get the power you want and still remain emissions compliant.
Like I said before I'd much rather swap to 3mz or a 2gr or even a 2az before I'd even consider a 2zr engine simply because the gains are more inline with someone who's modding a car would expect for power output.
40lbs is quite a bit of weight to add for 20hp but even so you still need an all the supporting parts to make it work plus its such a small gain I don't think its worth the effort.
I don't see what the issue with the c50 transmission is, for a higher powered engine the gear ratio's aren't terrible you just need to get a better final drive but that's not even that big of an issue since the weight gain is 80 lbs total for an extra almost 80 hp plus you also have room to grow and the engine has way better aftermarket support whereas the 2zr does not. The only reason I can see someone going with the 2zr is if they wan't to remain CARB compliant in which case I'd just sell the car and buy something else because it would be far easier and less of a hassle to get the power you want and still remain emissions compliant.
Like I said before I'd much rather swap to 3mz or a 2gr or even a 2az before I'd even consider a 2zr engine simply because the gains are more inline with someone who's modding a car would expect for power output.
aucorium ran 145/140 whp/wtq
Yaris TS 1800 Dyno results
guy on matrixowners.com ran 118whp with intake, header, axleback on a slushbox. that could be about 135whp with a proper transmission. also, keep in mind that the stock matrix/corolla/xd exhaust shrinks down to 1.75" (like the yaris) after the resonator, so removing the axleback/muffler section only would have less gains than adding a midpipe (available now through rpm headers, actually)
anyways, i see what you're saying, the cost/benefit ratio could be skewed. turbo is still likely the best bang-for-the-buck, but i still love to entertain the idea of the 2zrfe swap. i think it can be done on the (relatively) cheap.
edit: this dyno too, slushbox 2zrfe corolla with intake 116whp (could also be as high as 134-135whp with a manual (25% loss assumed for auto vs 13% for manual) - - 116whp/0.75 = 155bhp x 0.87 = 134.5whp manual)
2zz/c60 would also require switching to a throttle cable...and you'd need both the engine and transmission. 2zz's run $1000-1500 and c60's are 500-1000...plus all the other stuff.
for potentialy "simplicity", i still like the 2zrfe
Yaris TS 1800 Dyno results
guy on matrixowners.com ran 118whp with intake, header, axleback on a slushbox. that could be about 135whp with a proper transmission. also, keep in mind that the stock matrix/corolla/xd exhaust shrinks down to 1.75" (like the yaris) after the resonator, so removing the axleback/muffler section only would have less gains than adding a midpipe (available now through rpm headers, actually)
anyways, i see what you're saying, the cost/benefit ratio could be skewed. turbo is still likely the best bang-for-the-buck, but i still love to entertain the idea of the 2zrfe swap. i think it can be done on the (relatively) cheap.
edit: this dyno too, slushbox 2zrfe corolla with intake 116whp (could also be as high as 134-135whp with a manual (25% loss assumed for auto vs 13% for manual) - - 116whp/0.75 = 155bhp x 0.87 = 134.5whp manual)
2zz/c60 would also require switching to a throttle cable...and you'd need both the engine and transmission. 2zz's run $1000-1500 and c60's are 500-1000...plus all the other stuff.
for potentialy "simplicity", i still like the 2zrfe
the 2zz is compatible with the c50 and to keep the tb you'd just need to make an adaptor so you can use a tb from a drive by wire car like the tc or xrs matrix.
I get why you like the 2zr swap but looking at it by cost to benefit it just doesn't make sense unless you plan on boosting or something.
I get why you like the 2zr swap but looking at it by cost to benefit it just doesn't make sense unless you plan on boosting or something.
The c50 is a 5 speed. You wouldn't want to use it with the 2zzge, trust me. I had an 04 matrix XRS, currently own an 03 vibe GT, and I'm putting a c60 into a 1zz vibe today...Originally Posted by xnamerxx ↑the 2zz is compatible with the c50 and to keep the tb you'd just need to make an adaptor so you can use a tb from a drive by wire car like the tc or xrs matrix.
I get why you like the 2zr swap but looking at it by cost to benefit it just doesn't make sense unless you plan on boosting or something.
You NEED the close ratio 6 due to the 2zz's peaky/short powerband
X2 but my folks have the '03 XRS with the higher redline. 1st-2nd even as close as the gears are still puts you out of lift for a few hundred RPM shifting at 8300. The 5 speed would be useless with the 2ZZ.Originally Posted by thebarber ↑The c50 is a 5 speed. You wouldn't want to use it with the 2zzge, trust me. I had an 04 matrix XRS, currently own an 03 vibe GT, and I'm putting a c60 into a 1zz vibe today...
You NEED the close ratio 6 due to the 2zz's peaky/short powerband
I never found an issue with the Vibe GT transmission I'm sure a close ratio 6 is better but the Vibe GT and Matrix XRS are also quite a bit heavier over the Yaris your talking about a 550-600 lb difference between the Matrix and 800 for the Vibe.
Again, not sure where you get your info....the matrix vibe twins, except for body work, are identical. The 03-06 Vibe GT, I can assure you, is a 6 speed with a c60. The XRS/GT both weigh 2800lbs or so.
Its the 09+ XRS/GT that have the 2.4L 5 speed (same as the Camry/tC/xB2) with a beefed up curb weight of 3000+lbs
Bluevitz, you can land in lift 1-2 with the 03 lift of 6200rpm (I also used to have an 03 ecu in my 04 XRS) you just need to run it to the limiter and powershift into second...
Its only the celica's that really varied their redline from 8200, 8400 fuel cut. But to the best of my knowledge the always had lift at 6200rpm. 03 vibe/matrix was 6200, 04 6500, 05/06 (including Corolla ) was a useless 6800rpm. The corolla was actually pretty quick still due to 2500lb curb weight.
Its the 09+ XRS/GT that have the 2.4L 5 speed (same as the Camry/tC/xB2) with a beefed up curb weight of 3000+lbs
Bluevitz, you can land in lift 1-2 with the 03 lift of 6200rpm (I also used to have an 03 ecu in my 04 XRS) you just need to run it to the limiter and powershift into second...
Its only the celica's that really varied their redline from 8200, 8400 fuel cut. But to the best of my knowledge the always had lift at 6200rpm. 03 vibe/matrix was 6200, 04 6500, 05/06 (including Corolla ) was a useless 6800rpm. The corolla was actually pretty quick still due to 2500lb curb weight.
I'm just talking normal shifting 1-2 from limiter drops it down to around 5900-6000. Just under lift for a few seconds. The 5speed would be down to 4xxx for sure.
Shred. Only person I recall using a 5peed with a 2zzge was a guy screen named war in Alberta (iirc the location) had an imported MRS and built up the 2zz for turbo. He wanted Tue wider gears of the 5 speed since lift didn't matter for his setup and he raced on track, so less shifting was betterOriginally Posted by Bluevitz-rs ↑I'm just talking normal shifting 1-2 from limiter drops it down to around 5900-6000. Just under lift for a few seconds. The 5speed would be down to 4xxx for sure.
3SGTE
6 attachments not included in this copy
So according to the sticky, a 2zz can be swapped into the sedan. If I were to do that, I'd want motor/tranny combination, yes? And how tough would that be since mine is an automatic?
Has anyone thought about a fwd Sr20de engine from like an Infiniti G20 or a bluebirds nissan series?idk just a thought.
I am sure everyone has thought of every motor imaginable.
ANY motor swap is possible if you have the resources and funds. esp. from a different manufacturer. cant use the same ecu, would have to go standalone. custom everything from mounts to shift linkages, axles, exhaust, hoses. Again, its possible. just ridiculously expensive if you don't like wiring and welding and alot of trial and error
ANY motor swap is possible if you have the resources and funds. esp. from a different manufacturer. cant use the same ecu, would have to go standalone. custom everything from mounts to shift linkages, axles, exhaust, hoses. Again, its possible. just ridiculously expensive if you don't like wiring and welding and alot of trial and error
^ That post should be stickied at the TOP. Save us a lot of time.
To the top of each page also.. I feel people don't even look at post #1. At least he posted in the right thread instead of starting a new one.
every motor imaginable, and some you wouldn't dream of. If you throw me a trunk full of $1000 bills.
Hey Guys! Noob here... Don´t know if I´m posting in the correct place or not but here it goes. Wanted to know what would be the possibility of being able to fit an 4E-FTE with its 5 speed tranny into a third generation yaris. Would this be at all feasable, viable, possible?
way too much work for such little horse power motor. You may have a better chance sourcing out a 2zr motor from a euro yaris. Pretty much bolt right in prob with the euro motor mounts to go with it. Getting the wire harness and ecu also and trying to wire that up also. Depending if its LHD or RHD may have to extend alot of wires.
The 4E-FTE is only 130ish hp and so is the 2ZR.
just getting a supercharger is way less headache and cheaper for the same amount of power
The 4E-FTE is only 130ish hp and so is the 2ZR.
just getting a supercharger is way less headache and cheaper for the same amount of power
Well that makes a lot of sense, and I know that from a tech point of view it probably would´nt be the best choice (even thought the Yaris is what superceded the Starlet, which is part of the reason why I´m exploring this) however the reasoning behind the question is that I have what seems to be a 4E-FTE out of a later model Glanza V, complete engine, accesories, 5 spd. MT and 3 plug ECU MT. The intention is/was to install it into a 90 EL31 Hatchback with a tired oil 3E carb engine but considering the 4E engine and the 90 chassis and how difficult the parts are to get sometimes I began considering finding a 98 tercel fixer upper, but its kinda the same deal as the EL 31, so I figured if it would be possible to get into a newer model yaris or go with the tercel.
Forgot to thank ilikerice for the reply and input. Always appreciate an experts opinion.
OH yea, no problem.. I figured you had that motor sitting around. Looked at your yaris and then at the motor and a light bulb went off..
I have a 4age motor sitting in my garage right now. I have nothing to put it in but after seeing Etimago (misspelled prob) 4age swap on his yaris.. I think about it sometimes.. but then I dissmiss that thought. I would rather do a 2ZR swap and boost that instead. moar torque!
I have a 4age motor sitting in my garage right now. I have nothing to put it in but after seeing Etimago (misspelled prob) 4age swap on his yaris.. I think about it sometimes.. but then I dissmiss that thought. I would rather do a 2ZR swap and boost that instead. moar torque!
But that leaves your 4age collecting more dust. Putting a side the high probability that all the electronics would probably be an unresolvable headache I figured since the yaris is what came after the starlet/tercel it would´nt vary that much as far engine bay space is concerned. Even if mounts were to be relocated, I´m not quite sure if there would be enough space in the yaris engine bay to accomodate the 4E and having the axles line up properly. So what are going to do with the 4age?
Rick
Rick
Came out of my friends Mr2. Swapped his for a JDM 4ag-ze with LSD. Since I helped him do the swap he gave me his old stuff. It needs a rebuild really bad. When it ran, it created smoke clouds like jets create in the sky. I will rebuild eventually. Still gotta get this d16a6 back in a Crx I'm waiting for. Then a buddy has a miata engine that started knocking. Once those are out of the way I will start the 4ag rebuild unless I sell it dirt cheap.
Yeah, gave selling it dirt cheap a thought for a short while, but rather than doing that, I´d rather use it and put it in the old EL31. At least it´ll be a fun to drive car, which was more my original intention. Surely as you mentioned before, If one was after the most efficient, powerful, engine at the most convenient, economical price there are many other ways of achieving that without the 4E, but seeing as to what you already caught on to of having the engine I thought I explore other options prior to installing in the EL31. I was checking out this 2013 Yaris 5 door today and there may be enough room in the engine bay, but the whole set up looks so dif that I think I may be better of sticking to the original intention of the engine. I recall you saying in a previous message that it was too much work for such little power gain, but do you think its doable?
Hello guys!
I don't own a yaris buuuuut I'm interested in trying to swap the Yaris engine into my KP61 starlet. I know I know that the most popular swaps are 4ag or 13b rotary but I kinda wanted to stay as close as possible to it's 1.3L roots! And so the yaris is what I have in mind..
My questions are many but here's a few!
1. What would I have to modify on the engine to make it from fwd to rwd?
2. Anyone know of a rwd transmission that would be a straight bolt-on?
3. Even better has anyone performed this on any other car from fwd to rwd?
My Yaris gurus! I seek your knowledge and guidance! The Yaris engine would be an awesome upgrade if you consider that the original 4K-C engine only made:
The 1981 and 1982 California-spec 4K-C produced 58 hp (43 kW) at 5200 RPM and 67 lb·ft (90 Nm) at 3600 RPM.
I don't own a yaris buuuuut I'm interested in trying to swap the Yaris engine into my KP61 starlet. I know I know that the most popular swaps are 4ag or 13b rotary but I kinda wanted to stay as close as possible to it's 1.3L roots! And so the yaris is what I have in mind..
My questions are many but here's a few!
1. What would I have to modify on the engine to make it from fwd to rwd?
2. Anyone know of a rwd transmission that would be a straight bolt-on?
3. Even better has anyone performed this on any other car from fwd to rwd?
My Yaris gurus! I seek your knowledge and guidance! The Yaris engine would be an awesome upgrade if you consider that the original 4K-C engine only made:
The 1981 and 1982 California-spec 4K-C produced 58 hp (43 kW) at 5200 RPM and 67 lb·ft (90 Nm) at 3600 RPM.
You would need something like this, and even then, there's no way of knowing if/how it will fit.
http://www.ebay.com/itm/TOYOTA-SUCCE...aebe32&vxp=mtr
http://www.ebay.com/itm/TOYOTA-SUCCE...aebe32&vxp=mtr
That won't work at all! The starlet is a RWD configuration so I can't use that trans. The issue I can't find an answer to is finding a intake take faces the opposite way so that when the engine is in the rwd position the intake will face towards the front instead of the firewall. I will probably have to make a adapter plate for the transmission..
I need to research more before I commit to this swap!
I need to research more before I commit to this swap!
Originally Posted by CrankyOldMan ↑You would need something like this, and even then, there's no way of knowing if/how it will fit.
http://www.ebay.com/itm/TOYOTA-SUCCE...aebe32&vxp=mtr
If you are going to converted your car to rwd and doing a lot of fabricating to get mounts done. A custom intake manifold is the least of your problems.
Just take the existing intake. Cut the flanges off and build a box with runners going to the flanges. Make a hole with a pipe coming from the front and slap one of those custom cai piping and your done.
Just take the existing intake. Cut the flanges off and build a box with runners going to the flanges. Make a hole with a pipe coming from the front and slap one of those custom cai piping and your done.
2gr Confirmed.
Picture not included in this copy
Picture not included in this copy
^^^ not sure about this post?... Not sure what your saying here...
Also, that 2gr image isn't showing.. only see the sedan side profile picture..
On another note, this is about a month old now, but a guy from PR on a MicroImageOnline.com thread was able to swap a xD 2ZR in a yaris with minimal wiring fab only. You just need a xD donor car for the harness, ecu and motor of course.
Its alot of posts you gotta go thru but its pretty much a good DIY project and still running strong apparently.
Here is the tread,
http://microimageonline.com/forums/s...-TS-conversion
Also, that 2gr image isn't showing.. only see the sedan side profile picture..
On another note, this is about a month old now, but a guy from PR on a MicroImageOnline.com thread was able to swap a xD 2ZR in a yaris with minimal wiring fab only. You just need a xD donor car for the harness, ecu and motor of course.
Its alot of posts you gotta go thru but its pretty much a good DIY project and still running strong apparently.
Here is the tread,
http://microimageonline.com/forums/s...-TS-conversion
Hi
I have 2nz installed in my car and I would like to upgrade it to 1nz.
can these 2 engine be swaped with out the headache of electrical wiring??
I have 2nz installed in my car and I would like to upgrade it to 1nz.
can these 2 engine be swaped with out the headache of electrical wiring??
Yes the two motors are the physically the same. Though I'm not sure anyone has run a 1NZ on a 2NZ ECU before.
Engine is the most important part of a machine.
Here is a great way to give a swap a try and it is a pretty sweet price to start:
JDM 4EFTE
Less than a grand gets you a boosted motor with great internals and potential!
JDM 4EFTE
Less than a grand gets you a boosted motor with great internals and potential!
That wouldnt be a direct bolt up as far as motor mounts though, correct? I am not familar with the tercel and scartet chasis and motor setups.
but for 130ish bhp, don't know if it would be worth it if you still had to fab up parts and wiring....
Personally would rather do the xD 2zr swap..
but for 130ish bhp, don't know if it would be worth it if you still had to fab up parts and wiring....
Personally would rather do the xD 2zr swap..
For the same power and way better fuel economy, the 2ZR is the far better option.
The 4e-fte was direct from Toyota with forged internals. Very easy to make a lot more out of it and less of the electronic control and bullshit of today's engines. Yeah, you would need a little bit of fab work, but would be interesting I think.
From my m-o-b-i-l-e
From my m-o-b-i-l-e
Personally I can't really understand why someone would even consider FE if they are going to go through the process of a full swap. THE 4E-FTE is lighter than the 2zr, has stronger rods, and a very nice compression ratio of 8.5:1. Also it has a lightened crank from the factory. This motor has the ability to easily get 38-44mpg on the highway in the Yaris paltform even om the higher boost setting for the internal wastegate. Around 32-35 in the city I bet too. Since it doesn't have all the other electronic BS required as the newer engines I have known guys that have bumped it to 1 bar of boost, kept their FE, and been around 165-175hp handily. Then if you wanted to get really into it you can get 260-300hp out od it without even changing the internals. You won't do that I don't believe with the 2zr.Originally Posted by Bluevitz-rs ↑For the same power and way better fuel economy, the 2ZR is the far better option.
From my m-o-b-i-l-e
Stock motor vs stock motor.
Sent from my iPod Touch
Sent from my iPod Touch
If I am going thru all the trouble of doing a swap like that (fab mounts, fab wiring for ecu, fab axles/hubs, shift linkages, pedals for throttle cable), I would go with a 2zz motor. Stock vs stock. and even then the supercharger for the 2zz has alot of aftermarket parts for it, from the lotus, that are reliable upgrades.
I would like to do a 2zz swap, but I think the 2zr is going to be the best I can do since its been done and a fairly good write up on it on MicroImage website. That is if I do end up doing a swap. But the 1nz is a good platform as well to do a turbo as Garms old Yaris has shown us. As well as Blown xA and a couple other here who boost the crap out of thier 1nz. I think the only real issue with the yaris is the ecu. Damn thing is like a steel trap and is smart as f*ck
I would like to do a 2zz swap, but I think the 2zr is going to be the best I can do since its been done and a fairly good write up on it on MicroImage website. That is if I do end up doing a swap. But the 1nz is a good platform as well to do a turbo as Garms old Yaris has shown us. As well as Blown xA and a couple other here who boost the crap out of thier 1nz. I think the only real issue with the yaris is the ecu. Damn thing is like a steel trap and is smart as f*ck
I hear ya rice. I just think that it would be cool if someone did the 4e-fte swap showing another real option. I had considered the 2zz a long time ago then dismissed it because of the extra couple hundred pounds it it could end up being on thw front suspension. If you do the 2zr just make sure it is from the xD and not the previous years sin e there is the documented oil consumption issues. Yes the 1nz is a very capable engine, but as many have noted a pretty expensive one. Just a harness, switch to MAP, and full standalone is over 2k and I speak from experience.
From my m-o-b-i-l-e
From my m-o-b-i-l-e
Aren't you going to run into that issue with any Toyota engine? I don't think any Toyota OBD2 engine has great tuning support outside of the trucks.Originally Posted by fnkngrv ↑Yes the 1nz is a very capable engine, but as many have noted a pretty expensive one. Just a harness, switch to MAP, and full standalone is over 2k and I speak from experience.
From my m-o-b-i-l-e
I'm stuck dealing with OBD1 tuning issues on a Miata, and I just can't see why you would want that. OBD2/CAN is great from a tuning, and diagnostic standpoint.
Agreed, definitely a viable option compared to some. thanks for the tip on the xD. Agreed on the weight of the 2zz, but that stock rev limiter... I wants!
In a year or 2, never knwo what may drop in my lap. May come across a wrecked xD or Celica gts... I am rebuilding a 4age motor, but I don't think I wanna go that old school in a yaris.
In a year or 2, never knwo what may drop in my lap. May come across a wrecked xD or Celica gts... I am rebuilding a 4age motor, but I don't think I wanna go that old school in a yaris.
The 2ZR is being developed for the Lotus Elise, supercharger and all. I'm also entertaining pipe dreams of a 2ZR swap followed by a Blitz mod. Lots involved in that one.Originally Posted by ilikerice ↑I would like to do a 2zz swap, but I think the 2zr is going to be the best I can do since its been done and a fairly good write up on it on MicroImage website. That is if I do end up doing a swap.
That said, a 2ZR spec sheet I found lists a 0-60 mph time comparable to my 1NZ + Blitz, so it's more or less the same benefit.