Yarisworld Archive

Blitz SuperCharger Install

128 posts · 52,452 views · page 3 of 3

Replies continued

PETERPOOPThread starterOahu · Mar 10, 2009#101
Originally Posted by blacksandiegovitz ↑
Nice Bro ! So was it worth the money/time???
You know, I'd like a little more power. But who wouldn't, right? One could never be satisfied. But after knowing the power I've gotten with the blitz, I could never go back. So yes, worth the money/time. I just can't imagine how Garm's car would feel. 🙇
cali yarisCanoga Park, CA · Mar 10, 2009#102
Would the s/c guys go for an overdrive pulley? Is there room? Someone measure for that.
kurokoma-kunmy own little world · Mar 10, 2009#103
Originally Posted by cali yaris ↑
Would the s/c guys go for an overdrive pulley? Is there room? Someone measure for that.
How interesting, I was just discussing this with someone else.

How much enlargement is needed to see the benefit? I've seen overdrive pullies for the Mini that are just +2%...

There's less than a finger's width of clearance between crank and w/p pullies on the yaris--don't think that's enough? 🤷

I use my stock crank pulley as a paperweight however, I'll measure it tonight 😁

1 attachment not included in this copy

cali yarisCanoga Park, CA · Mar 10, 2009#104
That is probably too close to do anything good with, unless a smaller w/p pulley was included.

OR, you could remove the w/p pulley and go with an electric water pump, but then you have a project on your hands... 😁
JerkrattFair Lawn, NJ · Mar 10, 2009#105
^ hint hint lol
kurokoma-kunmy own little world · Mar 10, 2009#106
Originally Posted by cali yaris ↑
That is probably too close to do anything good with, unless a smaller w/p pulley was included.

OR, you could remove the w/p pulley and go with an electric water pump, but then you have a project on your hands... 😁
Hmmm, electric alternator too? 🤣 Anything to be just like you Garm... as in finally rid of that stock ECM! 😆 It's full of sorcery
cali yarisCanoga Park, CA · Mar 10, 2009#107
Yes -- I have snuck up on my car at night a few times and witnessed the eerie green glow from the ECU.... wonder what (or who) it is communicating with?
NonStopTuningUSA · Mar 10, 2009#108
Originally Posted by kurokoma-kun ↑
How interesting, I was just discussing this with someone else.

How much enlargement is needed to see the benefit? I've seen overdrive pullies for the Mini that are just +2%...

There's less than a finger's width of clearance between crank and w/p pullies on the yaris--don't think that's enough? 🤷

I use my stock crank pulley as a paperweight however, I'll measure it tonight 😁

Garm and I have chatted about this a couple times. And where there is a will, there is always a way. We have worked around such limitations in other SC Toyotas in the past. Think late 80s Toyota MR2 SC.

The dilemma we have has been the same one we have had since day one. We need someone with a SC Yaris, with the ability and willingness to test a pulley for us, and get some extensive dyno data with the stock pulley and any test pulley we offer. We have not had any serious takers.

You all know my phone number, my screen name, and my Email address. I am ready to chat whenever you guys are.

👍👍
AlexNet0Rockland, ME · Mar 10, 2009#109
Originally Posted by cali yaris
OR, you could remove the w/p pulley and go with an electric water pump, but then you have a project on your hands... 😁
Hey if you can source a bolt on electric water pump, demand is always pending availability, hehe
PETERPOOPThread starterOahu · Mar 10, 2009#110
I just want to say how AWESOME the car pulls when shifting down from let's say 5th to 3rd or 4th to second, or just being in higher rpms! I flew up the hill (freeway) today that I usually have to press the gas all the way down to make it up! Where's that s-10!? you're going down! Can't wait to open up the exhaust!

ps: my megan header came in today! whoohooo. 1 step closer to completing the exhaust!

I will be getting this magnaflow muffler for my setup. nobody probably will like that look, but i do, and that is all that matters! muaha. Website says $311, but if you have your local checkers bring it in, it was 270$. Can't wait!

2.25" in 3" out

Picture not included in this copy

http://www.magnaflow.com/02product/s...e=main&id=8054
marcustoronto, canada · Mar 10, 2009#111
Originally Posted by PETERPOOP ↑
I just want to say how AWESOME the car pulls when shifting down from let's say 5th to 3rd or 4th to second, or just being in higher rpms! I flew up the hill (freeway) today that I usually have to press the gas all the way down to make it up! Where's that s-10!? you're going down! Can't wait to open up the exhaust!

ps: my megan header came in today! whoohooo. 1 step closer to completing the exhaust!

I will be getting this magnaflow muffler for my setup. nobody probably will like that look, but i do, and that is all that matters! muaha. Website says $311, but if you have your local checkers bring it in, it was 270$. Can't wait!

2.25" in 3" out

Picture not included in this copy

http://www.magnaflow.com/02product/s...e=main&id=8054
always wanted the dual tip setup but no one sell an axleback like this..i dont want to weld.
LtNoogieWest Hills, CA · Mar 10, 2009#112
Peter, your eyes are getting heavy. You're dreaming of the one thing that will complete this install. mmmm... no more exposed valve cover and ignition wires.

Picture not included in this copy
PETERPOOPThread starterOahu · Mar 10, 2009#113
haha. if i do, it has to be after the exhaust is complete. sorry
PETERPOOPThread starterOahu · Mar 12, 2009#114
Originally Posted by LtNoogie ↑
Ok, young man. Your next mission is to tell the rest of us what's that weird noise when we turn on our A/C at idle.
Well I've had the car idle with the a/c on and there is no weird noise. I don't know if the noise has to do with pre-ignition, but all I know is that I am running Lucas Boost Octane and I hear nothing. I didn't want to experience the knocking and what not others have experienced, so I put that in. I don't know if it's helping it or not, but I am not experiencing any weird noises at all from the kit. Only the clicking when the compressor turns on, and that is normal (still getting use to it). Good luck with the noise.... 🙁
sleey0PA · Sep 19, 2010#115
Old thread, but could someone forward me the edited documetn that KK made illustrating all the bolts?

I am a complete noob at this and will need all the help I can get! lol
flyguysktsd · Sep 20, 2010#116
ya i want to supercharge my yaris hatch ... doe si t REALLY make the car feel better? i dont ned it to outrun corvettes or ferraris but the occasion minivan maybe.

where is the best place to buy a complete kit? cost?
fmicleSan Jose, CA, USA · Sep 20, 2010#118
It absolutely does, and then some. I also have a modified suspension and a rear sway bar, which I absolutely recommend before increasing power. The car is much more fun to drive, you will never look at it the same way again 🙂

The best place to buy the kit? www.microimageonline.com - Garm has the Blitz supercharger at the lowest cost I could find.
sleey0PA · Sep 20, 2010#119
Do the intake and supercharger gaskets need any sealant?
maxxman420San Diego, Ca · Sep 20, 2010#120
That is Awesome! you'll be squealin down the road! sexy part
flyguysktsd · Sep 20, 2010#121
so what are the perf numbers...i think i read it takes whp to 125 ish?
fmicleSan Jose, CA, USA · Sep 20, 2010#122
Originally Posted by sleey0 ↑
Do the intake and supercharger gaskets need any sealant?
Not that I know of... Just make sure you torque everything to spec consistently. Some members have had issues with shredded driving belts, but I've been running mine since February with no issues. I probably didn't tension the belt as much as I should have, but I don't get any squeaking, so I'm guessing it's enough. I was also very careful and spent a lot of time aligning all the pulleys, so that the belt doesn't have to run with sideways tension on it, trying to follow the pulleys. I have a used kit and I didn't get all the spacers that come with the standard kit, so I used washers to make my own spacers and made sure everything is aligned. As I said, so far so good, no issues whatsoever 🙂
fmicleSan Jose, CA, USA · Sep 20, 2010#123
Originally Posted by flyguyskt ↑
so what are the perf numbers...i think i read it takes whp to 125 ish?
That's about right, I didn't want to spend money on a dyno, so I don't know the exact numbers, but Blitz advertises a 30-40 HP gain, so if we go with conservative estimates we have, say 92 WHP stock + 30 from Blitz = 122 WHP. If you get the DC Header and an aftermarket exhaust you're probably looking at 5-10 HP more.

<shameless plug>I am selling my Tanabe Medalion Touring exhaust and I'll be selling my S/C kit as well in a couple of weeks 😉</shameless plug>
PETERPOOPThread starterOahu · Sep 20, 2010#124
Every dyno is different, so it's hard to tell. take it to the track.
sleey0PA · Sep 20, 2010#125
Thanks, fmicle and I sent you a pm:D

I wish I lived anywhere near Cali:(
sleey0PA · Sep 22, 2010#126
Can any of you supercharger guys take a picture of your stock ECU showing the wiring and also where you mounted the blitz piggyback?

THANKS!
fmicleSan Jose, CA, USA · Sep 23, 2010#127
Let me see what I have. The fuel controller is simply sitting behind the ECU, I just shoved in the there, no tape or cable ties or anything. The wires are short enough to keep it there even if I was to do barell rolls.

Picture not included in this copy

Picture not included in this copy

I had to fabricate a harness that was long enough so I can install the knob in the cabin:

Picture not included in this copy

Found a whole in the firewall under the right glove compartment, so I didn't have to drill one myself:

Picture not included in this copy

Tadaa:

Picture not included in this copy
sleey0PA · Sep 23, 2010#128
THANKS!

Haven't seen the wiring yet so I appreciate that:D