Yarisworld Archive

DIY - rear sway bar [pics]

198 posts · 157,468 views · page 1 of 4

cali yarisOriginal postCanoga Park, CA · Feb 21, 2009#1
Today we installed an Ultra Racing rear sway (anti-roll) bar on Babie Y's Yaris. I took a few pics, hope this is helpful.

First, jack up the back of the car (from the sides) and remove the rear wheels. This makes it easier to get to the bolts later.

Then, get out your sway bar. A friend, helper, bodyguard or whatever helps.

Picture lost · www.microimageonline.com


Look under the car. There is one large bolt holding the bottom of the rear shock. You can re-use this bolt. There is also a hole that isn't being used just in front of it, like this:


Picture lost · www.microimageonline.com


Here is the same two holes, shown from the inside angle instead:

Picture lost · www.microimageonline.com

Remove the bolt holding the shock. Place the swaybar with the bar at the bottom and so the holes line up. Re-install the bolt through the shock, then the sway bar, then a washer and nut. ***It is easier to do both shock bolts first, leaving the sway bar hanging -- then do the two front bolts.

That should look like this:

Picture lost · www.microimageonline.com

And like this:

Picture lost · www.microimageonline.com

Tighten and/or torque the nuts and you're done. In another thread there was consensus that "making them tight, but not crazy tight" was good enough for this.

thanks to supmet:
For the TRD bar, the torque specs are 36 ft/lbs on the bolt at the bottom of the suspension, and 44 ft/lbs for the other bolt.
Go drive the car, high-five your bodyguard... and have a nice day.

* (check and re-tighten, if needed after driving for a few days).
* the Ultra Racing sway bar comes with hardware -- I'm sure the TRD one does, too.
* Yes, that is a Tokico shock. 🙂

Replies 197

Kaotic LazagnaCentral Valley, CA · Feb 21, 2009#2
Sweet. Thanks for the write up, Garm. I might be working (no, not the work I'm doing now, but actually be getting paid for working) this summer in addition to my summer classes. This will be one of the things I'll be getting if I get the position at the hospital.
Nexus1155Dorchester · Feb 21, 2009#3
Question though, does it really make a compareable difference over stock, and i don't know if you sell both of them would you recommend the Ultra or the TRD one? They are both at a competitive price..

The yaris is lowered on 17's, and she likes to take corners hard...

I'm going to do some research on it, just wanted to hear it out of the mans mouth first hand
1NZYaris1New Zealand · Feb 21, 2009#4
It looks 🙄 just like the TRD one except it's WHITE 🤤
so if you want RED you have to pay more 😲
dam i should have waited a couple of months
and just paint it RED 😈
cali yarisThread starterCanoga Park, CA · Feb 21, 2009#5
does it really make a compareable difference over stock,
There is no stock sway bar included with the car!

Yes, this bar makes a big difference in cornering. Out of all the "bracing" and "bars" this is the one to get first and the one you will feel.

I think TRD is overpriced, but as a customer, it is good to have choices in the marketplace.
eTiMaGoBangkok, Thailand · Feb 21, 2009#6
argh i gotta get one of these someday 😁 nice writeup!
supmetSouthern California · Feb 21, 2009#7
Originally Posted by cali yaris ↑
Tighten and/or torque the nuts and you're done. In another thread there was consensus that "making them tight, but not crazy tight" was good enough for this, but if someone wants to post the torque spec for these bolts, that would be great.
For the TRD bar, the torque specs are 36 ft/lbs on the bolt at the bottom of the suspension, and 44 ft/lbs for the other bolt.
custom LftbackHouston, TX · Feb 21, 2009#8
what is the price for the ultra racing sway bar?
custom LftbackHouston, TX · Feb 21, 2009#9
nevermind, found an older thread. $129 shipped.
cali yarisThread starterCanoga Park, CA · Feb 21, 2009#10
thanks for the torque specs, added to first post
tk-421Dagobah · Feb 21, 2009#11
@cali: can you source unpainted (maybe just primered) bars?
Also, how thick is this bar compared with TRD?
cali yarisThread starterCanoga Park, CA · Feb 21, 2009#12
Ultra Racing 19mm, TRD 22mm (I'm told) -- I've tried both, can't really feel much of a difference.

Thinking about having them make a 23mm bar to play with.

Why would you want an unpainted bar? You can always re-paint it anyway?
westglCentral Point, Oregon · Mar 7, 2009#13
I bought my UR Rear Sway Bar from Cali Yaris, it shipped fast, received it very quick. It is easiest to put it on the way Cali Yaris describes. A small Pry bar will help to spread the bar and get it into place.

Driving: I noticed that the suspension felt Firmer and not bouncy as it was before, it remove the wander that this car has. Iam not constantly stearing to stay straight. The Wander is mostly gone. The car feel's more solid.

Handling: The handling is much improved, I feel that acident avoidance is greatly improved.

The car still has a slight amount of wander, maybe it's in the front end??

My Car has the Electric upgraded package that includes the upgraded Goodyear tires, not the Bridestones. The GoodYear tires hold the road better, and are allot quieter with less road noise coming into the car through the tires.

G
ShroomsterOrlando · Mar 8, 2009#14
meh.... when I installed the wife's TRD bar I just left the shock bolts facing the installed way and placed the new bolts facing the opposite way....

good write up GARM!
auxmikeLI, New Yawk · Mar 10, 2009#15
Originally Posted by Shroomster ↑
meh.... when I installed the wife's TRD bar I just left the shock bolts facing the installed way and placed the new bolts facing the opposite way....

good write up GARM!
I did the same thing!
I think that's what it showed in the diagrams in the instruction sheet.
Inspector14Anchorage, AK · Mar 10, 2009#16
Installed my Ultra sway bar a couple of weeks ago. man the handling is improved. i can really toss that little car around. (not too much still a bit of ice, and i have my snow tires on)

install was a snap. though i didn't tighten the shock bolt on the left side down all the way (got distracted) and was getting a horrible thunk sound. easy fix.
blacksandiegovitzJust chillin' out brah ! · Mar 10, 2009#17
Very nice , I still need to get one of these sway bars off you Garm .
yarisugiハワイ · Mar 10, 2009#18
Sorry for noob question.
Don't know much about rear sways bars, but how does this improve handling?
Being that it's a FF car (Front engine, Front wheel drive) and this is my first FF car.
Up until now, I've only driven FR or MR cars with front sway bars that make a huge difference.
Shed some light on grasshopper please.
cali yarisThread starterCanoga Park, CA · Mar 10, 2009#19
when you turn, weight is transferred to the outside wheel. A sway bar (or in this case because we have a beam rear axle, a "torsion" bar), resists this by transferring weight back to the inside wheel.

Roll is reduced, traction is increased and the car feels much more "secure" and flat in the turns.

How'd I do? 🙂
PHXDEMONPhoenix, AZ · Apr 15, 2009#20
Just bought one of these from you Garm. Couldn't save all my tax return money 😆 Can't wait to install it.
cali yarisThread starterCanoga Park, CA · Apr 15, 2009#21
cool man, you will like the result!
CtrlAltDefeatIndianapolis IN · Apr 15, 2009#22
mine is on it's way now... can't wait to install it 😁
PHXDEMONPhoenix, AZ · Apr 18, 2009#23
Just got the bar in today and installed it 🙇 to fast shipping. What suprised me is more than handling it actually improved the ride quality. Rear end is much more stable now and the car feels much less "bouncy" dropped on DF 210s. it also decreased a lot of body roll on hard turns and I no longer rub on hard turns which is awesome. Overall worth every penny :grin:
cali yarisThread starterCanoga Park, CA · Apr 19, 2009#24
I will be getting more, too -- they are now posted into the store.
chongopantsHouston · Jun 16, 2009#25
hey guys I am a newb in modding small cars, and its been a while since I have done anything. I think this is a good start. I have an 07 yaris, and I wanna know some cheap newb mods if you guys have any suggestions.
Thanks
1NZYaris1New Zealand · Jun 16, 2009#26
Originally Posted by chongopants ↑
hey guys I am a newb in modding small cars, and its been a while since I have done anything. I think this is a good start. I have an 07 yaris, and I wanna know some cheap newb mods if you guys have any suggestions.
Thanks
Handling wise , Shocks , springs ,and sway bars
engine wise Afe intake ,Nst Pullies , and up grade your excuast
+ aheap load of other things , Check out www.MicroImageOnline.com
Great place to visit , for ideas and products . 👍
CtrlAltDefeatIndianapolis IN · Jun 17, 2009#27
well when I first started modding my Yaris I came on here to ask which parts I should get. Here's that thread. I ended up getting a NST underdrive pulley, a NST Short Shift Kit and a set of Tanabe DF210 lowering springs. With the DIYs here on YW I installed all of them by myself (and then an Ultra Racing rear sway bar later) I wrote down my experiences here Including the sway bar I spent around $550 and completely changed my car. It made a world of difference, and I love every minute of it 😁
MUSKOKA800Chatham, Ontario, Canada · Jun 17, 2009#28
Originally Posted by westgl ↑
My Car has the Electric upgraded package that includes the upgraded Goodyear tires, not the Bridestones. The GoodYear tires hold the road better, and are allot quieter with less road noise coming into the car through the tires.
If the Goodyear LS rubber is an upgrade I feel sorry for those with B-stones.
I've never experieced rubber with less braking grip than these LS. They actually feel better in wet roads than dry???????? The ABS is singing! 👎
tk-421Dagobah · Jul 9, 2009#29
Just got the bar installed... Just came back from a drive and I can totally feel the car being more solid all around... It's much more fun to take twisties now.

Thanks for all the great goodies, Garm! My car thanks you (my wallet... not so much 😆)
KioshiFremont, CA · Jul 31, 2009#30
stupid question w/ having a one car garage only.... Is it required to take off the rear wheels, or can i squeeze on by through? Going to do install Monday evening when it comes by UPS.....
CtrlAltDefeatIndianapolis IN · Jul 31, 2009#31
Originally Posted by Kioshi ↑
stupid question w/ having a one car garage only.... Is it required to take off the rear wheels, or can i squeeze on by through? Going to do install Monday evening when it comes by UPS.....
Well I took them off to do it (put both sides on jack stands so i could jack up the suspension with my jack to lessen the sheer on the bolts and get them out easier) but someone else on here said they didn't have to take the wheels off...
KioshiFremont, CA · Jul 31, 2009#32
Originally Posted by CtrlAltDefeat ↑
Well I took them off to do it (put both sides on jack stands so i could jack up the suspension with my jack to lessen the sheer on the bolts and get them out easier) but someone else on here said they didn't have to take the wheels off...
I'll be raising the car w/ jack stand for sure, if i can squeeze my ratchet in between the wheels and the (2) bolts, I'll be good. Yeah, I just skimmed through the pages, but thats good to know someone did it w/o removing wheels.

Thanks for the response 🙂
CtrlAltDefeatIndianapolis IN · Jul 31, 2009#33
I think my ratchet was too thick to use without taking the wheels off...
KioshiFremont, CA · Jul 31, 2009#34
Mines a 3/8 husky ratchet.... its going to suck for me if thats the same size you have...
CTScottUSA, CT · Jul 31, 2009#35
I had to pull my rear wheels off to install mine. My wheels are 16x7's and I couldn't get the bar into place with them on.

I definitely agree with the huge handling improvement with the bar. I also installed the Ultra Racing strut tower bar, but I waited a couple of days between the two to see if I could notice a difference. For me, there's not a noticeable difference with the strut tower bar on, but maybe if I installed it before the sway bar it would have been more obvious.
CtrlAltDefeatIndianapolis IN · Jul 31, 2009#36
not sure. I did mine ghetto style with what ever tools lying around the dusty garage. I think i had to use a 3/8 to 1/2 adapter...
CtrlAltDefeatIndianapolis IN · Jul 31, 2009#37
Originally Posted by CTScott ↑
I had to pull my rear wheels off to install mine. My wheels are 16x7's and I couldn't get the bar into place with them on.

I definitely agree with the huge handling improvement with the bar. I also installed the Ultra Racing strut tower bar, but I waited a couple of days between the two to see if I could notice a difference. For me, there's not a noticeable difference with the strut tower bar on, but maybe if I installed it before the sway bar it would have been more obvious.
was that the front or rear strut bar?
KioshiFremont, CA · Jul 31, 2009#38
I'm on H&R lowering springs and 17's 42mm offset.....no torque wrench here either...
I'll see how it goes, required to torque it or no?
cali yarisThread starterCanoga Park, CA · Jul 31, 2009#39
It can be done without removing the wheels, but it's not as much fun. Have a Band-Aid ready for the knuckle that suffers the injury. 😁
CTScottUSA, CT · Jul 31, 2009#40
Originally Posted by CtrlAltDefeat ↑
was that the front or rear strut bar?
Rear for having to pull the wheels. I probably could have slid it into one wheel and then got it into place, but I didn't want to ding up the wheels with the bar or the wrench. My wheels are 16x7 +45 by the way.

I installed the front UR strut tower bar without removing the front wheels and without removing the wiper cowling. I jacked the front up and put it on jack stands and that gave me enough clearance to see to get the bolts up. On top, I found that I could get the socket on the passenger side with no problem and on the driver side I just had to flex the cowling up about 1/4" to get the socket on.
KioshiFremont, CA · Jul 31, 2009#41
Garm - no pain no gain :P

CTScott - Glad to know that, did you torque to specs or just tighten as much? I really dont want to spend 60+ for a torque wrench :(
cali yarisThread starterCanoga Park, CA · Jul 31, 2009#42
medium tight should be ok. 44 shock bolt, 36 front bolt if you torque them.
CTScottUSA, CT · Jul 31, 2009#43
Originally Posted by Kioshi ↑
Garm - no pain no gain :P

CTScott - Glad to know that, did you torque to specs or just tighten as much? I really dont want to spend 60+ for a torque wrench :(
I'm one of those people who only breaks out the torque wrench for engine work.
YAR1SRaleigh, NC · Jul 31, 2009#44
Im in a bit of a pickle.
I want this rear sway bar

But

do i have to lift it up to get the bar on? Im running stock wheels....

could I use two lift stands on either side?? I only have one but one from another car would be fine would it not?

Hmmm...
I would ask my mechanic but he's pretty old school and may have a fit about adding it on to my yaris... he doesnt even think the trim rings and dust caps are safe enough to have on there (he worries a lot about me, the old geezer :p ).

any thoughts?
ShroomsterOrlando · Jul 31, 2009#45
if you mean vehicle roadside jacks, I would say if you're in a real dill pickle then it'd be fine just find the lift points on the underside of the car.
CtrlAltDefeatIndianapolis IN · Aug 1, 2009#46
You should never get under a car with just the roadside flat tire jacks, they are too unstable... you really need jack stands... I'm pretty sure you have to lift the car to put it on.. the weight of the car will not let you remove the bolt you need to remove to install it (I would imagine the shock might pop out and possibly hurt you)
ShroomsterOrlando · Aug 1, 2009#47
Originally Posted by CtrlAltDefeat ↑
You should never get under a car with just the roadside flat tire jacks, they are too unstable... you really need jack stands... I'm pretty sure you have to lift the car to put it on.. the weight of the car will not let you remove the bolt you need to remove to install it (I would imagine the shock might pop out and possibly hurt you)
yeah you're right. why use something that's meant to hold the vehicle up in the first place. especially two of said item.

/sarcasm.

^^ctrlaltdefeat - don't take it like I'm dogging you or anything, just my horrible brand of humor

in all honesty though if you have the money to, invest in a nice jack and stands like mentioned.

also the shock will not pop out unless you give it enough clearance, and it will not come flying out either, merely fall out as there is no force applied to it. although they are somewhat hard metal
CtrlAltDefeatIndianapolis IN · Aug 1, 2009#48
well jack stands aren't that expensive (the cheapest ones will work, our cars are so light weight) and I'm saying that if you did remove the bolt holding the bottom without the car lifted up at the back the weight of the car will be compressing the shocks and 1. will be nearly impossible to move the bolt, and 2. if you did get the bolt removed, the end of the shock with the weight of the car on it will pop out of place suddenly... The flat tire jacks have small bases and are designed to be subjected mostly vertical force. You start wrenching on the car underneath it and it's likely to slip sideways and fall off of the stands.
cali yarisThread starterCanoga Park, CA · Aug 1, 2009#49
If you're on stock springs, I'm willing to bet it's possible to put this on without even jacking up the car. 👍
CtrlAltDefeatIndianapolis IN · Aug 1, 2009#50
Originally Posted by cali yaris ↑
If you're on stock springs, I'm willing to bet it's possible to put this on without even jacking up the car. 👍
ahh true... forgot that I had lowering springs on when I installed mine. Well on my install the weight of the car was compressing the shocks, and seemed like it would be a bit dangerous, so on stock springs you're right it might be ok, however I wouldn't risk it 😁