the blue is nice too! any of the colours will look slicker without the badges!
DeBadge / Remove Emblems How-To [pics]
136 posts · 66,409 views · page 3 of 3
Replies continued
Took mine off over the weekend. Just parked the car facing the sun and slowly yanked the badges off. No line needed and no glue residue to remove.
same here..just peeled ithe logos off then peeled the gum like adhesive off...wiped with a damp microfibre cloth....
That was easy. Took longer to find an extension cord for a hair dryer than it did to get those puppies off. Looks much nicer, I think.
congrats..yeah man easiest way is to just rip em off!!!
took me a while iv done 2/3 of it here are pics so far.
4 attachments not included in this copy
Good guide but what I did worked equally well and was a bit easy.
1. Spray a tiny bit of WD40 behind the embles
2. Wait 5 mins
3. Peel off the emblems either by hand or with some dental floss. Sinc eI didn't have any dental floss I just ripped them off by hand right to left.
4. Clean off whatever adhesive is left with Goo Off automotive cleaner, which will be very minimal as WD40 worked to loosen it up.
5. Clean the paint. I used Mcguires paint cleaner.
6. Wax! (I skipped this part cuz I had no time and I just waxed my whole car 3 weeks ago so I'll wax over that part when I wax it again later :)
Enojy the lack of emblems on your car!
1. Spray a tiny bit of WD40 behind the embles
2. Wait 5 mins
3. Peel off the emblems either by hand or with some dental floss. Sinc eI didn't have any dental floss I just ripped them off by hand right to left.
4. Clean off whatever adhesive is left with Goo Off automotive cleaner, which will be very minimal as WD40 worked to loosen it up.
5. Clean the paint. I used Mcguires paint cleaner.
6. Wax! (I skipped this part cuz I had no time and I just waxed my whole car 3 weeks ago so I'll wax over that part when I wax it again later :)
Enojy the lack of emblems on your car!
Saw two hatchbacks side by side today on the highway, one had ALL emblems on back taken off. Needless to say, it didn't look good without the middle toyota logo.
it needs the netz or the toyota logo in the middle.....because it has the 2 holes and the groove......yes i agree it needs the middle logo
I first debadged only the "Toyota" on the left of my sedan trunk, but then a couple weeks later I couldn't resist also debadging the "Yaris" on the right too. So now it's nice and clean and balanced, with only the Toyota logo remaining in the middle.
I did them both with just some dental floss and a wax detailing wipe to help clean up after. They were both pretty easy, but the "Toyota" was a little easier than the "Yaris" because it's a little smaller, with thinner letters, so therefore had less adhesive on the back holding it on. The dental floss broke a couple of times on the "Yaris".
Also made a point of saving both badges so that I can always reattach them later or give them to a buyer/dealer when I sell or trade the car (way down the road, no time soon 😆).
I did them both with just some dental floss and a wax detailing wipe to help clean up after. They were both pretty easy, but the "Toyota" was a little easier than the "Yaris" because it's a little smaller, with thinner letters, so therefore had less adhesive on the back holding it on. The dental floss broke a couple of times on the "Yaris".
Also made a point of saving both badges so that I can always reattach them later or give them to a buyer/dealer when I sell or trade the car (way down the road, no time soon 😆).
I'm now thinking that I may have jumped the gun a little with the debadging of the "Yaris" on the right (but I don't regret debadging the "Toyota" on the left at all, I like having that gone). So if I do decide to put the "Yaris" back on, I was wondering...
- Has anyone rebadged the "Yaris" in a different position than its original one (on the sedan)?
- Has anyone blacked out the "Yaris" (especially if on a white sedan) while keeping the Toyota logo in the middle chrome? I will probably leave the "Yaris" chrome too, but curious.
- Has anyone used "3M Plastic Emblem & Trim Adhesive", instead of the "3M Body Molding Tape" that seems to be used pretty often for rebadging?
Thanks.
- Has anyone rebadged the "Yaris" in a different position than its original one (on the sedan)?
- Has anyone blacked out the "Yaris" (especially if on a white sedan) while keeping the Toyota logo in the middle chrome? I will probably leave the "Yaris" chrome too, but curious.
- Has anyone used "3M Plastic Emblem & Trim Adhesive", instead of the "3M Body Molding Tape" that seems to be used pretty often for rebadging?
Thanks.
I removed the Toyota badges(front/back) and did this...applied 3M black carbon foil! The one on the trunk looks the same! Better pictures coming by the end of the week!
1 attachment not included in this copy
Well, I did end up reattaching both badges, and in their original positions (with the "Toyota" on the left and the "Yaris" on the right). Measured and marked off their positions to make sure they were even and level, and used the 3M Emblem Adhesive. Oh well, I guess debadging just wasn't for me after all. 🤷😎Originally Posted by eht13 ↑So if I do decide to put the "Yaris" back on...
i did this last weekend.. didnt even have to use a hairdryer.. just dental floss.. just put vitz on the back and got rid of toyota and yaris emblem.. looks cleaner..also installed netz emblem on the front..using a pinky it takes 10 seconds to pry the front emblem..
anyone have instruction on how to remove the front emblem bolted on
LOL that made my day Dylan, that was hilarious!!!
DONE!!!!! - Took 5min with a morning cup of coffee. No heating, just lightly "sawed" through with the fishing line, rubbed off the excess tacky clue, quick wipe down and done. She gets a wax job at the SPA tomorrow, so all perfect after that. Thanks for this.
Will post pics tomorrow after she is all polished up.
Will post pics tomorrow after she is all polished up.
Smooth 👍
Picture not included in this copy
Picture not included in this copy
All I did was take some fishing line and basically went underneath it working my way through the emblem. I was able to take it off after that pretty easily. Peeled off the left over glue and used some 3m rubbing compound to blend in the newly exposed paint.
Fishing line is way to much work. I use a vinyl application squeegee, knocks the emblems right off, without scratching the paint.
Picture not included in this copy
Picture not included in this copy
I've never had fishing line take more than about 30 seconds, but the squeegee looks like it would work too.
The fishing line worked great and very easy to do. There is a fishing line that is braided instead of mono or plastic material and
kind of the same as super high strength dental floss. I used Berkley Power Pro 30 lb. test which is the diameter of 6 lb. mono.
The stuff that's called Spider Wire is the same deal and can be purchased at any Walmart if you don't have a buddy who has some
in their tackle box. It slices through the adhesive like a hot knife through butter! Thanks for the tip on the fishing line method!
kind of the same as super high strength dental floss. I used Berkley Power Pro 30 lb. test which is the diameter of 6 lb. mono.
The stuff that's called Spider Wire is the same deal and can be purchased at any Walmart if you don't have a buddy who has some
in their tackle box. It slices through the adhesive like a hot knife through butter! Thanks for the tip on the fishing line method!
1 attachment not included in this copy
Where can I find the 3G tape used to rebadge after I paint my emblem? Home depot had a few types but wasn't sure whic one works best..
hmm to debadge or not..
I meant 3m tape. Stupid auto correctOriginally Posted by beebosaur ↑Where can I find the 3G tape used to rebadge after I paint my emblem? Home depot had a few types but wasn't sure whic one works best..
The stuff you want to pick up is available at Auto Zone or Pep Boys and it's made by 3M if I'm not mistaken, it's called body molding trim tape. The double sided foam adhesive tape is gray in color and has thin red plastic tape you peel off to expose adhesive.
Yep the 3m stuff is the one to get.
Seriously, I'm thinking if I should do it or not
YES!!Originally Posted by fase4 ↑Seriously, I'm thinking if I should do it or not
🤘🤘Originally Posted by Chuck G ↑YES!!
So it was 11:30 in the morning, I brought the garbage down, it had already been 93ºF/34ºC outside for several hours and the rear-end of my car is facing straight east...
Took me about 10 seconds on each the TOYOTA and the YARIS badge without any tools. As difficult as peeling the top slice of bread of a peanut butter sandwich. Just a bit of glue residue left, and some goo-off will take care of that later today.
Took me about 10 seconds on each the TOYOTA and the YARIS badge without any tools. As difficult as peeling the top slice of bread of a peanut butter sandwich. Just a bit of glue residue left, and some goo-off will take care of that later today.
Why not wait until it's hot outside, Yarflana? Will be much easier then.
did mine yesterday, just hit it with a hair dryer to warm it up then peeled it off. the emblems come off really easy, it's the giant globs of glue that are hard to get off. had to use my driver's license to scrape it away slowly then cleaned it with a little alcohol. luckily my car's a 2010 so the fading is minimal.
I like the cleaner look. Maybe just keep the Yaris on though.
I wish our yota' badges didn't leave weird shapes on the bumper and hatch...I want to remove them so bad.