Chris07LBOriginal postNew Jersey · Jul 16, 2006#1I know this is a rather easy "free mod" to do, but I remember a few asking how to do it.
Here is a super simple how-to, to get your rear end looking cleaner.. 😛
First step is to CAREFULLY warm up the emblems.. a few seconds is all it needs! A regular hair dryer works fine, but I had my heat gun close by, just be very careful if using one!
Work one side at a time.
Picture not included in this copy
Then get out some good 'ol fishing line. Dental floss will also work, but sometimes it's not strong enough, and will break easy.
Just get under an edge, and start "sawing" from top to bottom, all the way until you reach the other side.. simple! 🙂
Picture not included in this copy
There will be a little adhesive left behind from the emblem.
Picture not included in this copy
It comes off very easy with your finger nail. 🙂
Picture not included in this copy
Clean up whatever little bits are left behind, with WD40... Simple. 🙂
Repeat steps for other side.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
FINISHED LOOK Shine provided by Turtle Wax ICE.
Picture not included in this copy
Enjoy. 🍻
Replies 135
DylanbyGTA · Jul 16, 2006#2Very nice! I'm still debating on whether or not I'll do this.
Thanks for all the work you've been putting into your how-to's. I enjoy reading them, even tho' most aren't of practical use to me personally.
ChinoCharlesOH · Jul 16, 2006#3Great mod. Thanks Chris, looks sexy. Brings out the car's natural ghetto booty.
jhawkRichmond, VA · Jul 16, 2006#4that looks freakin sweet.👏
JDMVitzT.O. · Jul 16, 2006#5Nice! Always enjoy your DIY threads, keep it up!
TRD_YarisAustin, Texas · Jul 16, 2006#6You don't cease to impress me, chris07lb!!! I'll have to try the fishing line instead of dental floss. did you try the dental floss first and it kept breaking? 👍 I'm thinking of soaking the fishing line in liquid wax for awhile before..might make it slide a bit better and WOULD keep all the removal as a chemical/heat thing..not a mechanical "sawing" force that might come from dry fishing line. but, i'm just being nit-picky now 😳
AWESOME JOB..clean rear end!
eight_headsLA, USA · Jul 17, 2006#7 Originally Posted by Chris07LB
Shine provided by Turtle Wax ICE.
👍 yeah, i use it too.... like it so far
Chris07LBThread starterNew Jersey · Jul 17, 2006#8Next week will be Tanbe Spring Install How-To, & Cusco Lower Tie Bar How-To. 👏
Chris07LBThread starterNew Jersey · Jul 17, 2006#9 Originally Posted by TRD_Yaris
You don't cease to impress me, chris07lb!!! I'll have to try the fishing line instead of dental floss. did you try the dental floss first and it kept breaking? 👍 I'm thinking of soaking the fishing line in liquid wax for awhile before..might make it slide a bit better and WOULD keep all the removal as a chemical/heat thing..not a mechanical "sawing" force that might come from dry fishing line. but, i'm just being nit-picky now 😳
AWESOME JOB..clean rear end!
Actually, I think I could have gotten away without any heat. The fishing line made easy work of the adhesive, as I've done all my other cars in the past.. but heatin' her up a little just makes it that much easier. 🙂
HoccAus, HK · Jul 17, 2006#10Nice and clean .... i really wanted the white one cos i love the simple look....sadly...my dad don;t want to wait that long and we end up getting a silver lining color..does any one think that colour will suitable without the toyota badge?
JDMVitzT.O. · Jul 17, 2006#11 Originally Posted by Chris07LB
Next week will be Tanbe Spring Install How-To, & Cusco Lower Tie Bar How-To. 👏
👍 Looking forward to those
rstb88Tennessee · Jul 17, 2006#12I removed mine last month when our temp reached 100F and the humidity was aweful, so I grabbed the fishing line and took 'em off. Mine didn't leave that much residue and I could grasp it with my finger, nails hurt the paint even at a 'safe' angle. If you don't do it for the looks at least do it to keep from snagging on drying towels and wash mitts. I went through two wash mitts cause they kept geting caught on that and the back wiper. And can the back wiper extend up like the front windsheild ones when washing?
fnkngrvIn The Hotbox · Jul 17, 2006#13what pound test did you use? I just tried with some 20lb test and it broke halfway thru the YARIS....It is about 0 here right now and my car is in the direst sun...it looks like i could peel with my fingers the rest of the way, but I don't want to chance it.
Chris07LBThread starterNew Jersey · Jul 17, 2006#14 Originally Posted by rstb88
And can the back wiper extend up like the front windsheild ones when washing?
It only pulls back, about an inch or so.. won't tilt away like the fronts.
Wish it did, i know it makes washing the front windshield a lot easier. 😎
Chris07LBThread starterNew Jersey · Jul 17, 2006#15 Originally Posted by fnkngrv
what pound test did you use? I just tried with some 20lb test and it broke halfway thru the YARIS....It is about 0 here right now and my car is in the direst sun...it looks like i could peel with my fingers the rest of the way, but I don't want to chance it.
I'd have to look. It was thin, but like I mentioned above, I could have actually used NO heat at all, as it "sawed" right thru the TOYOTA emblem without any issue.
Just make sure your moving it up and down as you go from one side to the other.. spraying a little WD40 on the fishing line will help also.
👍
*EDIT* I just looked, it was a 25lb. test fishing line.
DylanbyGTA · Jul 17, 2006#16I'm kinda torn. I love the look of it debadged. But I like people knowing my car's a Yaris.
I mean when I'm driving slow, & by slow I mean the speed limit in the right hand lane, I want the guy riding my arse to know I'm driving a Yaris for pete's sake. Obviously I don't care about being the lead car. Go around me & race to the next red light & I'll meet up with you shortly. For me driving a Yaris is like putting a sign outside my car that says "F-Off, I'm commuting here".
fnkngrvIn The Hotbox · Jul 17, 2006#17 Originally Posted by Dylanby
For me driving a Yaris is like putting a sign outside my car that says "F-Off, I'm commuting here".
Dude...that is awesome!🤘
I am removing mine cause it is fun. I have the only Yaris in my county still, plus a color that is rare for the S....plus it is an S which to my knowledge is still not offered in my state so it adds that mysterious air about it.😁
Chris07LBThread starterNew Jersey · Jul 18, 2006#18Ive always said, "keep 'em guessing!" 😁
JustAnotherAsianmilpitas / santa rosa · Jul 18, 2006#19hm. that looks clean.
on other cars, it looks pretty naked with a shaved-emblem look, but on the yaris, it looks pretty natural imo.
can't wait to see results in a sedan as well!
PixieDawnTampa, FL · Jul 18, 2006#20mikeukrainetzCanada · Jul 18, 2006#21I pulled my emblems on a hot day and the whole thing came right off without leaving one peice of glue and I didnt use any fishing line. Just wiped off the dirt residue around the letters afterward.
eight_headsLA, USA · Jul 18, 2006#22well i like the look, but i'm still debating whether or not to do it... hmm
Chris07LBThread starterNew Jersey · Jul 18, 2006#23 Originally Posted by eight_heads
well i like the look, but i'm still debating whether or not to do it... hmm
Remember, you can always put them back on if you dont like the look.
3M Body Tape, the super thin, super strong double sided tape that body shops use, can be found.. just gotta look. 👍
Before even going outside, just do a quick photoshop like I did, and see if you like the debaged look. 👏
mikeukrainetzCanada · Jul 18, 2006#24worst case you wind up putting them back on right..
ChinoCharlesOH · Jul 18, 2006#25Yeah, an 85 degree Ohio summer day, some 8 lb test fishing line, and a little rub of the thumb and my badges are off. This should be a no brainer... the back end of this car has wonderful lines, too nice to have those two silver plastic badges. Not only that, but I found that a little PVC epoxy adheres that Yaris badge very well to your run of the mill Samsung cell phone. Right on... customized my car and my phone all in one day. Pictures of both soon... pretty priceless shit haha.
mikeukrainetzCanada · Jul 18, 2006#26lol...
Chris07LBThread starterNew Jersey · Jul 19, 2006#27 Originally Posted by ChinoCharles
Yeah, an 85 degree Ohio summer day, some 8 lb test fishing line, and a little rub of the thumb and my badges are off. This should be a no brainer... the back end of this car has wonderful lines, too nice to have those two silver plastic badges. Not only that, but I found that a little PVC epoxy adheres that Yaris badge very well to your run of the mill Samsung cell phone. Right on... customized my car and my phone all in one day. Pictures of both soon... pretty priceless shit haha.
🤣 👏
KSIbuckyFond du Lac, WI · Aug 1, 2006#28if you dont have dw-40 (i found out i didnt right when i finished) lighter fluid will work and NO YOU DONT HAVE TO LIGHT IT ON FIRE AND YOU SHOULDN'T EVER PERIOD END OF SENTENCE. just put some on a paper towel or a rag just remember to wash your hands
Chris07LBThread starterNew Jersey · Aug 1, 2006#29 Originally Posted by KSIbucky
if you dont have dw-40 (i found out i didnt right when i finished) lighter fluid will work and NO YOU DONT HAVE TO LIGHT IT ON FIRE AND YOU SHOULDN'T EVER PERIOD END OF SENTENCE. just put some on a paper towel or a rag just remember to wash your hands
....then remember to was that area, and put a quick coat of wax on it.
That wouldnt have been my second choice of product to use, but to each their own.
How do you like the new look? 😁
tomjaszLost Wages · Aug 1, 2006#30A great look, but at 112F with the west sun in the afternoon on a black HB in Las Vegas the badge almost falls off. The glue is like warm bubble gum. Huge inprovement to the toyota adverts stuck to the hatch!
OxyG3nEMontreal , Quebec , Canada · Aug 1, 2006#31i did exatly what u said .. hair dryer and and the thing for the teeth.. for perfection took 10 minute to do it lol
JustAnotherAsianmilpitas / santa rosa · Aug 22, 2006#32new question: does the center toyota-logo badge have little notches in them, which would leave holes on the trunk if removed? just wondering.
Originally Posted by Chris07LB
It only pulls back, about an inch or so.. won't tilt away like the fronts.
Wish it did, i know it makes washing the front windshield a lot easier. 😎
prius owners had the same thing- till someone found a way to make them pull back just like the front wipers by grinding the stopper or something like that.
it's in priuschat.com, but i can't find the link. sorry.
Chris07LBThread starterNew Jersey · Aug 22, 2006#33 Originally Posted by JustAnotherAsian
new question: does the center toyota-logo badge have little notches in them, which would leave holes on the trunk if removed? just wondering.
Yes, two of them.
SimmZQuebec · Aug 22, 2006#34Great write-up, but removing glue is a real pain in the ass...
Have you just try to heat badges a little, then simply pull on it slowly? I debadge all my 5 previous cars and I simply heat the badges and pull on it slowly, then all the glue came with the badge!
One easy step! No mess to clean after! 🎉
OxyG3nEMontreal , Quebec , Canada · Aug 22, 2006#35took 5 seconde to remove the glue that last lol
Chris07LBThread starterNew Jersey · Aug 31, 2006#36 Originally Posted by SimmZ
Have you just try to heat badges a little, then simply pull on it slowly?
Yea. Step one.
ViolinNew Jersey · Sep 5, 2006#37Did it:
Picture not included in this copy
Thanks for the how to.
8 lb. test fishing line is a little light.
Go with something heavier if you gots.
Chris07LBThread starterNew Jersey · Sep 5, 2006#38 Originally Posted by Violin
Did it:
Picture not included in this copy
Thanks for the how to.
8 lb. test fishing line is a little light.
Go with something heavier if you gots.
I posted up that I used 20, it was perfect. Even strong dental floss will work, and leave your emblems minty fresh!
Now I think I like that chrome garnish even more! 👍
ChinoCharlesOH · Sep 5, 2006#39Chris, you should grab it and paint it flat black to match your new emblem.
Chris07LBThread starterNew Jersey · Sep 5, 2006#40 Originally Posted by ChinoCharles
Chris, you should grab it and paint it flat black to match your new emblem.
Hummmm.... idea!
Keep an eye ball out for my front emblem post soon...😉
ViolinNew Jersey · Sep 5, 2006#41Did I mention all the James Bond type security mods I'd made to the car?
I wouldn't go near that emblem if I were you.
Chris07LBThread starterNew Jersey · Sep 5, 2006#42 Originally Posted by Violin
Did I mention all the James Bond type security mods I'd made to the car?
I wouldn't go near that emblem if I were you.
Color-Matched Front Emblem [pics] 🙄
fred812pa · Sep 7, 2006#43 It only pulls back, about an inch or so.. won't tilt away like the fronts.
Wish it did, i know it makes washing the front windshield a lot easier
black plastic cap at rear removes quite easily, and its hold there for replacement or wash/wax
Chris07LBThread starterNew Jersey · Sep 7, 2006#44 Originally Posted by fred812
black plastic cap at rear removes quite easily, and its hold there for replacement or wash/wax
not going thru the trouble of actually removing it, just to wash behind it. if it wasn't lifting high enough to wash behind, I still dont see myself removing it, to clean the glass.
GabLToronto · Sep 7, 2006#45 Originally Posted by Violin
Did it:
Picture not included in this copy
Thanks for the how to.
8 lb. test fishing line is a little light.
Go with something heavier if you gots.
Is that the exhaust tip??
ViolinNew Jersey · Sep 7, 2006#46Yes. Yes it is.
Chris07LBThread starterNew Jersey · Sep 7, 2006#47Space portal.
daq421Livermore, CA · Sep 7, 2006#48That looks super clean and very nice... the chrome bit also looks good.
-Peter
JfoofooNew Jersey · Sep 7, 2006#49I did it... didn't use any heat.. just put a nylon string under the emblem and whole thing came off with no glue left behind on the car in 5 seconds.👍
Super easy and looks very nice👍 . It's great to keep people guessing what I am driving. Thanks for this simple DIY.🙇
argylesocksmanch · Sep 8, 2006#50 Originally Posted by Chris07LB
I know this is a rather easy "free mod" to do, but I remember a few asking how to do it.
looks great :) nice job.