BasmiiOriginal postTexas · May 10, 2020#1Due to this pandemic, it looks like I'm going to have time this summer to try this swap.
This is a bigger job than I've ever attempted so hopefully I don't screw stuff up to badly.
The car is a 09 mt hatch.
Parts gathered so far:
Xd mt ecu
Xd mt harness ( relatively poor shape)
Xd auto harness( in case I need to salvage a broken connector)
MWR lightweight flywheel and bolt set
Cheap knockoff DC intake with a good KN filter
Xd clutch kit (Luk)
There are lots of Corolla engines near me in the 600 to 800 range so I need to decide on one and determine what is missing or needs replacement.
I read thru the other swap threads on here and the wiring part is still a little confusing. I figure it is probably something that will make sense once I get into it.
I'll do my best to post some pictures and any advice is appreciated.
Replies 65
CrankyOldManWest Michigan · May 11, 2020#2Awesome! Glad to see another cultist--er, conversion started. Looking forward to seeing your build.
Welcome to YW!
BasmiiThread starterTexas · May 11, 2020#3Appreciate it man. I'm sure I'll have a million questions for you and the others who have done it.
mitch9521Red Deer, AB · May 12, 2020#4Makes me want to start gathering parts to swap my '14, xDs are a chore to find in yards, especially manual ones.
CrankyOldManWest Michigan · May 12, 2020#5 Originally Posted by
mitch9521 ↑ Makes me want to start gathering parts to swap my '14, xDs are a chore to find in yards, especially manual ones.
Indeed. I found an MT xD at a dealership with lots of body damage for about $3500 and considered buying it just to pull it apart and make a kit from it. I've found one MT locally at a you-pick and it was in awful shape--Great Stuff foam in the already-deployed steering wheel airbag, kludge fixes everywhere.
CrankyOldManWest Michigan · May 12, 2020#6 Originally Posted by
Basmii ↑ Appreciate it man. I'm sure I'll have a million questions for you and the others who have done it.
There's a lot of info to digest but reading through the existing build threads will probably answer a lot of them. There shouldn't be very many--if any--unknown unknowns at this point but it's possible. I'll be happy to help either way. =)
mitch9521Red Deer, AB · May 12, 2020#7 Originally Posted by
CrankyOldMan ↑ Indeed. I found an MT xD at a dealership with lots of body damage for about $3500 and considered buying it just to pull it apart and make a kit from it. I've found one MT locally at a you-pick and it was in awful shape--Great Stuff foam in the already-deployed steering wheel airbag, kludge fixes everywhere.
Quick question, do Corolla or Matrix engine harnesses work for this swap or does it have to specifically be from an xD? Rollas and Matrix' are super easy to find in yards.
CrankyOldManWest Michigan · May 13, 2020#8 Originally Posted by
mitch9521 ↑ Quick question, do Corolla or Matrix engine harnesses work for this swap or does it have to specifically be from an xD? Rollas and Matrix' are super easy to find in yards.
The Corolla and Matrix have the ECU on the driver's side, next to the battery and fuse box, the Yaris is on the passenger side. I'm pretty sure that Project Vios has a Corolla harness, but it had to be reworked pretty significantly to move the connector to the other side of the engine. I don't recall if there are pin incompatibilities on that harness but it's possible some wires have to be relocated in the connectors. The xD is direct fit, no faffing about. =)
BasmiiThread starterTexas · May 17, 2020#9Started working on my MT harness this morning. It appears that there are three kind of shady connections near one of the fuse box plugs. Beyond that it seems in ok shape.
Anybody got tips for depinning this thing? I tried just pressing on the little plastic tab inside with no luck.
1 attachment not included in this copy
stidnamAustralia · May 18, 2020#10I can't see the bottom of the connector, but do they have a secondary locking bar on the other side that needs to be pulled up first?
Most of these plugs just need the primary tab lifted up from inside before pulling the pin out. But many of them also have that secondary locking bar as well that needs to be disengaged first
06YarisRSFredericton, New Brunswick, Canada · May 18, 2020#11Yay! This is great! I've been waiting for another 2ZR swap to happen. I was apprehensive and frankly a little lost (nay, a lot lost) when I started, but the amazing guys here held my hand through the process. I hadn't done much more than brakes, oil changes and a few bolt on parts before my swap. Congrats! 👍 I'll add my 2 cents...I was advised by the YW gang to get a 2-day membership to TIS TechInfo and download all the necessary wiring diagrams across the 3 platforms I was working with: 2011 Corolla (my 2ZR engine), 2006 Yaris (my car) and 2008 ScionXD (harness and ECU). This helped me immeasurably in terms of understanding how the electrical worked, plus confirmed what the guys here were saying. It improved my confidence and taught me more about the basics of automotive wiring. Again, congrats, and welcome to YW; the best automotive website - ever!
BasmiiThread starterTexas · May 19, 2020#12No secondary tab as best as I can tell. I have a buddy that is going to bring over a set of specialized pin tools that he thinks will work. If not I will just cut the existing repairs and resolder/shrink wrap them on the connector.
myfirstyotaToronto Canada · May 23, 2020#13http://imgur.com/a/2ESv8Ax http://imgur.com/a/lfEUG4m http://imgur.com/a/3UCr9Ba The bottom link is what the fuse box plug will look like when you are ready to pry up the tab inside the connector that holds the pin in. If the 'bar' on the side of the connector is flush with the connector the pins will not come out as they are locked un place. Use a pry tool (small screwdriver or a sturdy pick) to lift the lock as pictured in the third link.
Hope that helps
BasmiiThread starterTexas · May 29, 2020#14I picked up my motor this week. 53,000miles out of an A/t Corolla for $600. It's missing the exhaust manifold which may be the universe telling me to buy an expensive header.
1 attachment not included in this copy
CrankyOldManWest Michigan · May 29, 2020#15 Originally Posted by
Basmii ↑ No secondary tab as best as I can tell. I have a buddy that is going to bring over a set of specialized pin tools that he thinks will work. If not I will just cut the existing repairs and resolder/shrink wrap them on the connector.
As someone who works in the automotive manufacturing industry, I
highly discourage anyone from soldering connections on an automotive wire harness. The vibration stress will cause them to fail and become a nightmare to troubleshoot. Maybe not right away, but eventually. Crimping is the way the OEMs do it, you should too. =)
Looks like a beauty of an engine! Hopefully the internals are clean as well. If you've got some spare cash for the swap and want to be the first to try it,
monkeywrenchracing.com has a long tube header for the 2ZR Corolla. No idea if it will clear the firewall and fit into the Yaris tunnel, but someone needs to find out. ;)
BasmiiThread starterTexas · May 29, 2020#16 Originally Posted by
CrankyOldMan ↑ As someone who works in the automotive manufacturing industry, I
highly discourage anyone from soldering connections on an automotive wire harness. The vibration stress will cause them to fail and become a nightmare to troubleshoot. Maybe not right away, but eventually. Crimping is the way the OEMs do it, you should too. =)
Looks like a beauty of an engine! Hopefully the internals are clean as well. If you've got some spare cash for the swap and want to be the first to try it,
monkeywrenchracing.com has a long tube header for the 2ZR Corolla. No idea if it will clear the firewall and fit into the Yaris tunnel, but someone needs to find out. ;)
Do you recommend the regular heat shrink butt connectors or do I need to use something different?
06YarisRSFredericton, New Brunswick, Canada · May 29, 2020#17CrankyOldManWest Michigan · May 31, 2020#18 Originally Posted by
Basmii ↑ Do you recommend the regular heat shrink butt connectors or do I need to use something different?
Aah, I see that it's already been damaged/spliced. Ideally you would replace the whole wire to maintain the integrity of the insulation but that's not really practical in most cases. Heatshrink butt splices are fine here, just make sure you have a proper tool for both crimping and heating.
CrankyOldManWest Michigan · May 31, 2020#19 Originally Posted by
06YarisRS ↑
😆
(Shhhh, there's already one in my garage!)
06YarisRSFredericton, New Brunswick, Canada · Jun 3, 2020#20 Originally Posted by
CrankyOldMan ↑ 😆
(Shhhh, there's already one in my garage!)
Hmmmm.... Interesting! Are you holding out on us Sam? I found one on eBay for $40.00 - or maybe it was $80.00 - a year or so ago. I almost bought it when I was in the turbo system 'scratch build' thought process mode. Anyway, they are one solid, well constructed piece, aren't they. I only wish I'd sprung for the ceramic coated option when I ordered my kit. Mine started to get a wee bit of surface rust the few days after it was simply installed on the car.
CrankyOldManWest Michigan · Jun 3, 2020#21We've totally hijacked this poor person's thread! =D
I bought it as a pre-emptive measure so that I didn't miss out on it the way I missed out on the RPM long tube header. Zero plans to do FI on my daily driver, I can barely maintain it as NA.
06YarisRSFredericton, New Brunswick, Canada · Jun 4, 2020#22 Originally Posted by
CrankyOldMan ↑ We've totally hijacked this poor person's thread! =D
I bought it as a pre-emptive measure so that I didn't miss out on it the way I missed out on the RPM long tube header. Zero plans to do FI on my daily driver, I can barely maintain it as NA.
You're right, we have hijacked. Largely my fault. My apologies to the op. Good to have the mani lying around, 'just in case'.
BasmiiThread starterTexas · Jun 5, 2020#23I'm still shopping around for the header. The MWR piece is a bit pricey for me though.
I did go ahead and buy all the stuff I'll need to build a complete 2.25 exhaust. Should be a pretty miserable job without a lift.
My main job now is sourcing accessories and all the hardware that my engine is missing.
BasmiiThread starterTexas · Jun 10, 2020#24Does anyone have a good picture of the factory engine hooks?
I am going to weld up my own using some old ones I have of a miata.
stidnamAustralia · Jun 10, 2020#25I've ordered some but they haven't arrived yet. Can take photos when they do.
CrankyOldManWest Michigan · Jun 11, 2020#26Here's the set I have on my spare 2ZR. Front is just a simple flat hook with an anti-rotation tab on the collar. Rear is a bit more complex because it is perpendicular to the mounting surface and has a slightly more complex anti-rotation tab.
5 attachments not included in this copy
BasmiiThread starterTexas · Jun 12, 2020#27 Originally Posted by
CrankyOldMan ↑ Here's the set I have on my spare 2ZR. Front is just a simple flat hook with an anti-rotation tab on the collar. Rear is a bit more complex because it is perpendicular to the mounting surface and has a slightly more complex anti-rotation tab.
That is a great help. Thanks!
BasmiiThread starterTexas · Jun 24, 2020#28Bought a WPN-R header on EBay last week for $280.
I can't imagine it will make much power over the stock piece but it is full stainless and well made.
1 attachment not included in this copy
06YarisRSFredericton, New Brunswick, Canada · Jun 24, 2020#29 Originally Posted by
Basmii ↑ Bought a WPN-R header on EBay last week for $280.
I can't imagine it will make much power over the stock piece but it is full stainless and well made.
That's a beautiful piece! It definitely looks like it would breathe better than the stock manifold.
BasmiiThread starterTexas · Jun 29, 2020#30Discovered a large crack in my intake manifold this weekend...I'm having to source one from my local yard.
Does anybody have thoughts on which one is best? It looks like there are at least two designs and a recall on some of them. The placement of the vacuum hose for the brake booster is the only visual difference I can see.
06YarisRSFredericton, New Brunswick, Canada · Jun 29, 2020#31 Originally Posted by
Basmii ↑ Discovered a large crack in my intake manifold this weekend...I'm having to source one from my local yard.
Does anybody have thoughts on which one is best? It looks like there are at least two designs and a recall on some of them. The placement of the vacuum hose for the brake booster is the only visual difference I can see.
Dang. That sucks. Sorry to hear that. What are you doing with the cracked manifold? I seriously considered buying one from a wrecked car (assuming it's not and arm and a leg) and sawing through it to see the internal composition. I have an interest in the internal structure in relation to my water injection system. My tuner has assured me that even though it's a dry manifold - not intended for liquid injection - that the massive airflow would not allow any pooling of the injected water. We have a gigantic band saw at our school and I would basically chop the manifold in half (a cross section of sorts) and explore the internals. I would hate to do this to a fully intact manifold, but one that was damaged would make a perfect candidate. For example, one from a frontal collision that resulted in manifold damage.
BasmiiThread starterTexas · Jun 30, 2020#32 Originally Posted by
06YarisRS ↑ Dang. That sucks. Sorry to hear that. What are you doing with the cracked manifold? I seriously considered buying one from a wrecked car (assuming it's not and arm and a leg) and sawing through it to see the internal composition. I have an interest in the internal structure in relation to my water injection system. My tuner has assured me that even though it's a dry manifold - not intended for liquid injection - that the massive airflow would not allow any pooling of the injected water. We have a gigantic band saw at our school and I would basically chop the manifold in half (a cross section of sorts) and explore the internals. I would hate to do this to a fully intact manifold, but one that was damaged would make a perfect candidate. For example, one from a frontal collision that resulted in manifold damage.
Its already gone unfortunately...I wish I would have seen this before they picked up trash yesterday.
Neinris‘Murica! · Jul 2, 2020#33 Originally Posted by
Basmii ↑ Discovered a large crack in my intake manifold this weekend...I'm having to source one from my local yard.
Does anybody have thoughts on which one is best? It looks like there are at least two designs and a recall on some of them. The placement of the vacuum hose for the brake booster is the only visual difference I can see.
Use a 2ZZ intake manifold!!!
https://www.toyotanation.com/threads...#post-14000058 BasmiiThread starterTexas · Jul 3, 2020#34 Originally Posted by
Neinris ↑
That would definitely sound better.
06YarisRSFredericton, New Brunswick, Canada · Jul 3, 2020#35 Originally Posted by
Basmii ↑ Its already gone unfortunately...I wish I would have seen this before they picked up trash yesterday.
Haha. No worries.
BasmiiThread starterTexas · Jul 12, 2020#36Was finally able to grab a passenger side mount from my local yard this weekend. This part has been the hardest one to find by far.
I'm also struggling to source a stainless exhaust flange in the factory size if anyone has any ideas.
2 attachments not included in this copy
BasmiiThread starterTexas · Jul 17, 2020#37The coolant tube on my Corolla engine had an extra outlet.I assume for the auto trans cooler? I Picked up a XD version, but you could probably plug it somehow also.
1 attachment not included in this copy
06YarisRSFredericton, New Brunswick, Canada · Jul 17, 2020#38Where on the car are those tubes? Are they from the top of the engine, attached to the head? The Auto trans cooler is just in the bottom of the rad with rubber inlet and outlet hoses. Is that tubing part of the throttle body heater/cooling circuit? The other aluminum tubing on top of the engine is for vacuum to the brake booster, afaik.
BasmiiThread starterTexas · Jul 18, 2020#39 Originally Posted by
06YarisRS ↑ Where on the car are those tubes? Are they from the top of the engine, attached to the head? The Auto trans cooler is just in the bottom of the rad with rubber inlet and outlet hoses. Is that tubing part of the throttle body heater/cooling circuit? The other aluminum tubing on top of the engine is for vacuum to the brake booster, afaik.
Its the one that feeds the heater hose/throttle body. It runs across the trans side of the motor.
BasmiiThread starterTexas · Jul 18, 2020#40Pic of the XD tube installed.
1 attachment not included in this copy
BasmiiThread starterTexas · Oct 26, 2020#41This project had to take a back seat to work stuff for a bit but I managed to get it the swap done this weekend. If you disassemble the front end of the car getting the old motor out is not a big deal. I left the short driver's side axle attached to the transmission until it was out because there is not a lot of clearance to a prybar on it under the car. Beyond that I don't think I did anything different than the others on here..
1 attachment not included in this copy
BasmiiThread starterTexas · Oct 26, 2020#42Speedometer wires from the old harness.
BasmiiThread starterTexas · Oct 26, 2020#43Pink black and white
1 attachment not included in this copy
BasmiiThread starterTexas · Oct 26, 2020#44New engine in without issue.
1 attachment not included in this copy
BasmiiThread starterTexas · Oct 26, 2020#45I never could find a bell flange to fit the Wpnr header so I ended up buying one for a Honda and drilling new holes that a narrower. This allowed me to use one of the wider holes to mount a triangle bracket that I build to support the header.
BasmiiThread starterTexas · Oct 26, 2020#46New exhaust center section.
1 attachment not included in this copy
BasmiiThread starterTexas · Oct 26, 2020#47Engine fired up immediately. Runs fine but is way too loud. I may need buy a bigger muffler rather than reusing the magnaflow I had on it before.
BasmiiThread starterTexas · Oct 26, 2020#48Ok so I'm having problems now. The engine runs but nothing else works. No power steering and the P/S and ABS dash lights are both on. Tried driving it to the end of my street and the dash lights were flickering. My battery voltage is only about 11.8v but no fault codes on my scan tool. Maybe I left a ground wire off or something....?
stidnamAustralia · Oct 27, 2020#49Is that 11.8v while the engine is running?
06YarisRSFredericton, New Brunswick, Canada · Oct 27, 2020#50 Originally Posted by
Basmii ↑ New exhaust center section.
OMG, that's a thing of beauty!