Yarisworld Archive

New 2zrfe swap.

66 posts · 58,446 views · page 2 of 2

Replies continued

CrankyOldManWest Michigan · Oct 27, 2020#51
Originally Posted by Basmii ↑
Engine fired up immediately. Runs fine but is way too loud. I may need buy a bigger muffler rather than reusing the magnaflow I had on it before.
I originally went with a single catalytic converter and a DynoMax VT muffler but it was really harsh in the cabin. Added a DynoMax Race Bullet where the OEM resonator was and it really mellowed it out. Looks great so far!
CrankyOldManWest Michigan · Oct 27, 2020#52
Originally Posted by Basmii ↑
Ok so I'm having problems now. The engine runs but nothing else works. No power steering and the P/S and ABS dash lights are both on. Tried driving it to the end of my street and the dash lights were flickering. My battery voltage is only about 11.8v but no fault codes on my scan tool. Maybe I left a ground wire off or something....?
Might be the alternator is bad. You should be seeing at least 13.5V when running, up to 14.5 at high RPM.

The flickering lights is odd, might be a loose connection on the ECU wire harness? What else did you change between the engine and the cluster?

P/S light is strange, I haven't seen that one. Is the P/S fuse good? All the wires under the dash connected correctly? The P/S relies on ABS for the speed signal to adjust the amount of assist, could be that the ABS light indicates a problem that's putting the power steering into limp mode. Do an ABS diagnostic and see what codes you get from it--jumper pins 4 and 13 on the OBDII port and read the flashing lights sequence on the (security?) light.
BasmiiThread starterTexas · Oct 27, 2020#53
Think I got the alternator issue sorted. Went thru and cleaned up all the ground points with some fine sand paper and it is charging properly now. P/S and ABS lights are still on. I think I made a mistake with the speed sensor wiring.I have a dtc code for a circuit malfunction. Does this look correct?

2 attachments not included in this copy

CrankyOldManWest Michigan · Oct 27, 2020#54
Originally Posted by Basmii
Think I got the alternator issue sorted. Went thru and cleaned up all the ground points with some fine sand paper and it is charging properly now.
Good deal!

P/S and ABS lights are still on.
Run the ABS diagnostics test and see what blink codes you get.

I think I made a mistake with the speed sensor wiring.I have a dtc code for a circuit malfunction. Does this look correct?
Looks correct to me, matches my documentation on adding those wires. Make sure that they're not shorted anywhere and are pinned correctly on the sensor end as well:
* Pin 1 = Black
* Pin 2 = White w/Black stripe
* Pin 3 = Pink

Let's get you rollin!
BasmiiThread starterTexas · Oct 27, 2020#55
I'll try to do the ABS diagnostic in the morning. Probably need to jack the car up and make sure there isn't any damage to the wiring that goes to the front brakes.
BasmiiThread starterTexas · Oct 28, 2020#56
Ok I got four flashes plus two of the check engine light. Code 42 is speed sensor circuit/ power steering ecu if I'm reading it correctly.
CrankyOldManWest Michigan · Oct 28, 2020#57
Are you sure it's the check engine light? It should only be flashing the P/S light or the ABS light. Blinking check engine light usually means massive intake leak and potential damage to the catalytic converter.
BasmiiThread starterTexas · Oct 30, 2020#58
Check engine for sure. It's just blinking during the test procedure, not while the car is running.Four blinks, pause, followed by two blinks. I tried to upload a video but I guess the file is too large.


Unfortunately I'm out of time to work on it right now. I have to travel for a few weeks for work. I'll try to sort it when I get back.
BasmiiThread starterTexas · Nov 9, 2020#59
Returned and looked at it with fresh eyes. Replacing a blown 10amp fuse under the dash fixed everything👍 Drove it a good 100 miles today without issue.
06YarisRSFredericton, New Brunswick, Canada · Nov 10, 2020#60
Originally Posted by Basmii ↑
Returned and looked at it with fresh eyes. Replacing a blown 10amp fuse under the dash fixed everything👍 Drove it a good 100 miles today without issue.
Feels good, doesn't it! 😁
BasmiiThread starterTexas · Nov 11, 2020#61
Originally Posted by 06YarisRS ↑
Feels good, doesn't it! 😁
For sure. It's amazing how much smoother an engine the 2zr is. I'm really glad I spent the extra dollars for the MWR flywheel too.
06YarisRSFredericton, New Brunswick, Canada · Nov 11, 2020#62
Originally Posted by Basmii ↑
For sure. It's amazing how much smoother an engine the 2zr is. I'm really glad I spent the extra dollars for the MWR flywheel too.
I noticed the difference in smoothness between the 1NZ and 2Zr as well. I bet throttle response would be improved with the aftermarket flywheel.
CrankyOldManWest Michigan · Nov 14, 2020#63
Originally Posted by Basmii ↑
Returned and looked at it with fresh eyes. Replacing a blown 10amp fuse under the dash fixed everything👍 Drove it a good 100 miles today without issue.
Awesome, glad it was an easy fix!
BasmiiThread starterTexas · Dec 7, 2020#64
1 month update:

No issues after getting the early fuse problem sorted. I've driven it about 1800 miles so far and I'm averaging about 33mpg.

My initial goal for this car was to recreate the performance and feel of some of the small lightweight cars I owned in my younger days (specifically the mk1 gti I had in high school) and it is very close.

It is still not"fast" by any measure,but the 2zr revs quick and is very smooth and torquey above 3000rpm.

Some of the good things:

The MWR flywheel is worth every penny. The clutch action is a little more on/off switch in traffic but it's nothing I can't live with.

The actual swap was much easier than I expected.If you disassemble the front end most everything is accessible and the 2zr fits back in easily.

I'm expecting it to be every bit as reliable as the old motor.

The car gives off a cool "sleeper" vibe now.


And the bad stuff:

The new cat/exhaust continues to smell terrible. I was expecting that for the first couple of hundred miles but it hasn't gone away yet.

It is way loud! I ended up welding on an old school Supertrapp end cap to quiet it down but that isn't a permanent solution.

I decided to replace a bunch of other stuff (axles,control arms, brakes) at the same time and ended up spending alot more money than I initially intended.

I'm not entirely sure if the 2zr sits lower in the engine bay, but my oil pan seems very vulnerable. It's easily the lowest point on the car. I have plans to fab up a protective skid plate out of some hdpe cutting board material but that will have to wait till spring. Hopefully I don't run over anything in the interim.
stidnamAustralia · Dec 8, 2020#65
Awesome to hear. With regard to the flywheel - do you notice any rev hang? I have a factory flywheel on my 2zr and it's horrible. So much worse than the 1nz and particularly in 1st gear which is quite short in my setup
BasmiiThread starterTexas · Dec 8, 2020#66
Originally Posted by stidnam ↑
Awesome to hear. With regard to the flywheel - do you notice any rev hang? I have a factory flywheel on my 2zr and it's horrible. So much worse than the 1nz and particularly in 1st gear which is quite short in my setup
That is still there unfortunately. Can't say if the flywheel improves it without driving them back to back.