Yarisworld Archive

3rd gen 2zr swap with 6 speed

97 posts · 124,228 views · page 1 of 2

stidnamOriginal postAustralia · Jan 17, 2019#1
After exchanging private messages with a few members over the past few months and now finally acquiring a donor vehicle for the conversion, I think it's time to share some details about what I'm planning and what I've learnt so far.

This conversion will be slightly different to the other conversions done to date, and I suspect the first one done in Australia. Therefore, hoping the details here open up some options for those looking to do the conversion in the future.

I'm no stranger to engine conversions, but this will be the newest car I've done an engine swap on. I've never had to deal with immobilisers, can buses, etc. Cars of the 90's are much more simple to work on.

The recipient vehicle
Back a few months ago I sold my Toyota Starlet on a whim and within the same day picked up a 2012 Yaris ZR - similar external styling to the American SE model, but 2 doors and comes with few extra creature comforts. Kind of funny it was given the ZR designation from factory. I'll be ensuring it lives up to that original designation ;)

I've already sorted out suspension, sway bar, and a few other bits and pieces. Overall I'm happy with it as a replacement for the Starlet, but the seating position is horrible! On the flip side, visibility is great, which probably suits the target market - teenage girls and the elderly.

Picture not included in this copy


The donor vehicle
In Australia the 2zr first appeared in our 2007 ZRE152 Corolla. It was matched with a C66 gearbox until 2009 when the car got a facelift and the gearbox was replaced with an EC60, which is the same gearbox the Scion IM uses. The EC60 has a shorter casing than the older C6X boxes and also as an internal slave unit as opposed to the external slave of the C6X.

The Aus delivered EC60 transmission has ratios of: first, 3.538; second, 1.913; third, 1.310; fourth, 0.971; fifth, 0.818; sixth, 0.700; and reverse, 3.333. It is matched to a 4.562:1 final-drive ratio.

The facelifted ZRE152 appears to be the perfect donor for the conversion for a number of reasons - 1. The engine ECU is still plug and play with the 2012 Australian Yaris body loom, and; 2. The EC60 should fit into the Yaris chassis without modification to the frame rails. In theory, this provides a 2ZR 6 speed package that can be dropped in.

Soooooo.....I went out and purchased an entire wrecked one owner 2012 ZRE152 Corolla with 25k miles on the clock. Here in Australia if a car has been declared a statutory write off, it can never be registered again, and more common older models go for dirt cheap. This then provides one with the luxury of having everything running before hand and all ancillaries that match the motor.

The goal now: try and recoup the purchase price of the entire car by selling off all the remaining parts, thus ending up with a free motor and gearbox. Not holding my breath, but I've made back 10% of the total cost so far :)

Picture not included in this copy


The conversion
I haven't actually started to strip the motor from my donor car. That won't happen till some time in February. In the meantime, the focus remains on trying to recoup the initial outlay and sorting out the remaining unknowns involved with putting this combo in a Yaris. I've chunked down the conversion into a few categories - some which are resolved and some not so much.

Engine mounts
In 2008 Toyota released a 2ZR 6 speed Yaris in Europe, South Africa, and New Zealand. That particular model came with an EC67 gearbox. Interestingly, when they came to build the new 2017 GRMN Yaris, they dug into their parts bin and used the exact same mounts and bolted an EC62 into it. Therefore, my assumption has been that the same mounts will work to bolt the entire Corolla setup into the 3rd gen Yaris chassis. I've obtained all the mounts required as well as some additional mounts if I need to revert to using the C54 in the Yaris. For reference sake, the part numbers to bolt the 2ZR + EC6X box in are

Engine side bracket - 12315-37040
Engine side isolator - 12305-37190
Dogbone bracket - 12313-37010
Dogbone isolator - 12363-37010
Gearbox mount bracket - 12325-37100
Gearbox mount isolator - 12372-37141

Some of these mounts are common with the XD, but the gearbox side mount is unique to the EC6X Yaris setup. Those mounts had to be obtained from New Zealand.

Shifter cables
This part is going to be a little tricky. The C50 shifter cables are different lengths and the shifter setup sits more towards the front of the gearbox, whereas the EC6X shifter cables are closer in length to each other and the selector setup sits more towards the back of the gearbox. Toyota wanted $500 US for the GRMN shifter cables. I'm not ready to drop that kind of money on two little cables, but it's nice to know they are available if all else fails.

For the moment, I've obtained a set of Scion IM shifter cables in hopes they are the right length. All failing that, I have the option of buying some shifter cables from the UK (They put an EC6X in a fair few of their 3rd gen models, but there's no garentee they are long enough to suit the 2ZR position in the bay). I also have the ZRE152 cables as well, but I'm assuming they are all but useless given the shifter setup in that car.

So a bit of work to do here and a crucial piece of the puzzle to solve if I'm going to get this to work.

Drive shafts
The Euro 2ZR Yaris with EC6X gearbox uses the exact same drive shafts as the 2ZR yaris with the C50, and the same part numbers are also shared with the Scion XD and Toyota IST. Therefore, my assumption is that these shafts will at least be the right length and slide into the EC60 as well as into the Yaris hubs. I just need to import a pair from somewhere :(

The other option I have is the Corolla ZZE122 here in Australia. Investigations have revealed the drive shafts to be extremely close to the length to what I need, but further investigation is needed to confirm they'll actually fit and if I'll be able to retain the factory ABS.

On the topic of ABS, I was initially concerned about losing ABS if sourcing shafts from another model as I didn't understand how the ABS sensor worked. Tom has been kind enough to clarify for me that the ABS is picking up off the wheel bearing as opposed to a ring gear on the shaft. It would seem that both the Scion XD and 3rd gen Yaris utilise the same method of sourcing the ABS signal this way so I *think* I'm ok on this front.

ECU and Immobiliser
The ZRE152 Corolla and the Yaris share very similar wiring and immobiliser setups. I was originally looking at swapping out the immobiliser ECU as well and getting custom keys made up to match the car as well as the immobilser, but after seeing Adam's approach of registering the new 2ZR ECU to the immobiliser ecu, I'm going to cross my fingers and give that a punt when it comes time. There's a couple of options to fall back on, but I'd rather not think about that at the moment.

Radiator Fan
This is the only other difference I'm expecting I'll have to resolve when comparing against the other 2ZR swaps. The ZRE152 ECU triggers a separate radiator fan computer that varies the fan speed. I'm anticipating I'll have to utilise the same setup in the Yaris and wire the Yaris fan into the Corolla fan ECU. I'm not anticipating it to be a big deal, but something to note for anyone else considering the same swap.


Everything else with the swap seems pretty straight forward as per everyone else's 2ZR swap. While I hope to get everything pulled out and inspected in the next month or so, I don't expect to start the swap till later in the year. I feel a little nervous ripping apart a perfectly functioning vehicle just because I want another 25% more power and torque :) I also won't do the swap until I literally have everything ready and I'm confident I can have a functioning swap in one weekend. In the meantime I'll provide some updates on compatibility of drive shafts etc and anything else I find while investigating the rest of the unknowns.

Replies 96

myfirstyotaToronto Canada · Jan 17, 2019#2
Blazin trails. Love it.

Wtf... The NA market never gets the good lookin rides
atomic_hojiKincardine, ON, Canada · Jan 17, 2019#3
Originally Posted by stidnam
...
I feel a little nervous ripping apart a perfectly functioning vehicle just because I want another 25% more power and torque :)
...
Awesome to see your build thread started! 👍

It takes equal parts bravery, determination, and blatant disregard for common sense to tear apart a perfectly good, running, and relatively new vehicle.. Don't know what kind of dummy would do that.. 😁 (there's a few of us! hah)

With the number of people who've swapped the 2ZR on YW now I think you've got a good support group to make it work. Can't wait to see how you make out with the transmission mounting and axles - I'd love to pop a 6-speed in, but the C6x being longer meant frame cutting. The GRMN using the EC6x brought hope, and now you're stepping up to prove it! 👍

Anxiously awaiting project day..
-- Adam
MaritimeWoodstock nb · Jan 18, 2019#4
Signing up to watch.
tmontagueCaledonia Ont. · Jan 18, 2019#5
Good stuff, looking forward to following this build. I agree with the above post, that is a nice looking front end on your Yaris, too bad we dont have that option in NA
CrankyOldManWest Michigan · Jan 18, 2019#6
WANT! I've been theorycrafting an EC6x gearbox swap for a long time, this will be awesome to see it come to life!
atomic_hojiKincardine, ON, Canada · Jan 18, 2019#7
The 2012-2014 Yaris (hatchback) SE bodywork is very similar, if not exactly the same, but with in a 5-door version. No idea what perks the ZR has on the interior or gadget front; curious now though.. hah.

Given the whale-mouth on the 2015+ - now complimented by the snub-nose on 2018+ - I'd thought about buying the earlier bumper as CAPA certified ones aren't terribly expensive. Unfortunately, paint to colour-match is fairly expensive.. and I've grown to like the snub-nosed, whale face of the 2018, lol. Also, money spent on bodywork is money not available for awesome stuff like a 6-speed swap. 😁

-- Adam
thebarberGrand Rapids, MI · Jan 18, 2019#8
Subscribed
stidnamThread starterAustralia · Jan 18, 2019#9
Adam, I don't think there's too much difference in the interior either, but we get automatic climate control, telescopic steering, auto headlights, and the run of the mill Fujitsu-ten touch screen GPS unit (it's not that great). Seats and the rest of the interior looks the same

What you need for your third gen though is this badge for the hatch ;). Excuse how dirty it is.

Picture not included in this copy

Cranky, any other insights from your theorycrafting? All the parts cross checking I've done says it's possible. It's just the shifter cables being the big unknown.

Happy to forward the details of where I got the gearbox mount from in NZ if anyone else wants to give it a punt while I'm mucking around taking my time ;)

I will take detailed pictures of the gearbox when I pull it out to show mount points etc. I'll be testing that all the brackets I've purchased fit said mount points as well. Can also take measurements and confirm axle spline count etc etc.
06YarisRSFredericton, New Brunswick, Canada · Jan 18, 2019#10
Originally Posted by thebarber ↑
Subscribed
+1
stidnamThread starterAustralia · Jan 18, 2019#11
I forgot to mention the shifter cage needed for the 6 speed. I've worked that out though. The bolt pattern to mount the cage to the floor is the same across both 2nd and 3rd gen Yaris as well as the Scion IM and a lot of other models I suspect.

I've purchased a Scion IM (Corolla ZRE182) shifter cage with the reverse gear pull ring. Will now need to find an appropriate shift boot that matches my interior and centre console. Looking at the Euro Yaris 6 speed models to see if I can get something that's a direct fit. Will need something with red stitching to match.
ern-dizCA all day · Jan 18, 2019#12
Sub'd!
CrankyOldManWest Michigan · Jan 21, 2019#13
Originally Posted by stidnam ↑
Cranky, any other insights from your theorycrafting? All the parts cross checking I've done says it's possible. It's just the shifter cables being the big unknown.
The EC6x uses a hydraulic cylinder for the throw out bearing, not the arm-and-slave-cylinder that the C-series uses. You could probably fab custom lines, but I'm an OEM parts kind of guy for this stuff. Gonna have to think some more about what other differences there are.
stidnamThread starterAustralia · Jan 21, 2019#14
Yeah the clutch lines have been on my radar as well. The EC60 hard lines come around on the left hand side and the chassis rail on the Corolla. I haven't looked at the Yaris, but I'll get some comparison pictures when I pull the EC60 gearbox out.

In the meantime I've checked the parts manual and the diagrams look very similar in respect to the hard lines coming from the master cyl on a RHD car. I wouldn't be surprised if it all just bolted/screwed up. Maybe a new custom soft line...maybe

GRMN Yaris
Picture not included in this copy

2012 Gen3 Yaris
Picture not included in this copy

Edit: equiv images for LHD models

GRMN Yaris
Picture not included in this copy

2012 Yaris
Picture not included in this copy
BugeyeSydney · Jan 22, 2019#15
Good luck with the build buddy. I will be watching this closely
stidnamThread starterAustralia · Jan 22, 2019#16
Originally Posted by Bugeye ↑
Good luck with the build buddy. I will be watching this closely
Why not come join in the fun instead ;) 2zr's are cheap as chips in Straya.
myfirstyotaToronto Canada · Jan 22, 2019#17
Originally Posted by stidnam ↑
Why not come join in fun instead ;) 2zr's are cheap as chips in Straya.
That like "Murica"? Lol

Cause we got "tronno" here
stidnamThread starterAustralia · Jan 23, 2019#18
Originally Posted by myfirstyota ↑
That like "Murica"? Lol

Cause we got "tronno" here
Exactly :)

A few more parts arrived today. I received most of the rubber coolant hoses, except for one of the main radiator hoses - not sure how that got missed.

Short hose from heater core - 87245-52151
Long hose from heater core - 87245-52141
Clamps for heater core hoses - 96136-42501
Short hose to radiator - 16573-37030
Filler neck - 16502-37010
Long hose off filler neck - 16571-37090
Clamps for large coolant hoses - 90467-33006
Bottom radiator hose - 16572-37080
Engine stay - 12317-37010

Decided to buy new clamps all round just in case, and decided to purchase the engine stay for the RH engine mount. A few people have dismissed the need for this as they can't see a reason for it. Toyota wouldn't have added it though if they didn't have a reason (triangulation of engine mounting for additional strength maybe?), and in keeping this as factory as possible, why not add it back for the $15 it's worth.

There's a couple of things I'm still missing though, and not sure what I can use off the Corolla/Yaris vs what I need to buy new. Maybe Adam can comment.

- Intake to air cleaner pipe
- Engine ventilation hoses coming off intake and cam cover
- Fuel vapor hoses
- Brake booster vacuum hose

Planning to do a comparison between the Corolla and Yaris for all those parts when I pull the motor out early Feb anyway.

Also understand that a lot of the above part numbers etc have been documented in many of the 2ZR threads, but just recovering here for the benefit of anyone looking at this thing from start to finish.
BugeyeSydney · Jan 23, 2019#19
Originally Posted by stidnam ↑
Why not come join in the fun instead ;) 2zr's are cheap as chips in Straya.
Yeah I been doing my research. I have an 07 but wasn’t keen on chasing the XD parts.
But am contemplating getting a 2012 and going the same route as you.
stidnamThread starterAustralia · Jan 23, 2019#20
Shouldn't make a difference if it's 2007 or 2012. You'll have to chase the exact same parts.

The parts we don't have readily available to us are
- Axles
- Shifter cables (For C50/C54 in the slight forward and left mounted 2ZR setup)
- Airbox

You should be able to procure those through US Ebay sellers if keen enough.

The Toyota IST and the NZ market is always another source of parts. The 3rd Generation Toyota IST is the same car as the Scion XD. It just never came out as a manual in Japan, but the driveshafts in the 2zr version are the same as the manual Scion XD, and in theory the airbox should fit as well. Just be aware that the IST came out with a 1nz as well and you aren't going to want the parts from that variant.
BugeyeSydney · Jan 23, 2019#21
Ok cool.
Might start pricing parts up.
I really wanted to keep the corolla box over the Yaris 5 speed due to my daily m7 run.

Still in the back of my mind I’m concerned with keys/immobilizes also,
5 stud and disc brake rear would be awesome also
stidnamThread starterAustralia · Jan 23, 2019#22
Yeah fair enough. Being up front about costs, you're looking at the best part of $1000 for all the required brackets and isolators. Or you can go down the route that others have and only swap the engine side bracket over and keep your C54 (assuming the AU version bolts up).

The immobilser concerns me as well, but I take some solace in what Adam did to register his ECU to the immobiliser ECU. There's clear instructions on how to do it, and it sounds fairly logical.

Disc brake rear end is never happening I'm sorry unless you import the rear end from Japan at an unearthly cost :( We never got any Yaris or equiv chassis with a disc brake rear end I'm afraid.
myfirstyotaToronto Canada · Jan 23, 2019#23
Not sure about your market. But 2 months ago I found a 2012 Yaris se with rear disks in the u-pull yard. Don't ask me why it was there. 2012 was about 6 years newer than any other car there. $50 got me an axle that essentially had to be stripped and rebuilt (wheel bearings, calipers and brackets, ebrake cables) even though I have to replace all that, I'm still looking at a rear disk conversion for $700cad with all new parts. Not bad...

I think its just one of those things.... Some will have avenues of making it happen... Some won't.
NYC-SENYC · Jan 23, 2019#24
Originally Posted by stidnam ↑
Disc brake rear end is never happening I'm sorry unless you import the rear end from Japan at an unearthly cost :( We never got any Yaris or equiv chassis with a disc brake rear end I'm afraid.
So you're telling me that your Yaris ZR, which looks exactly like our Yaris SE, has drum brakes? Interesting as our SE has discs.
stidnamThread starterAustralia · Jan 23, 2019#25
Originally Posted by NYC-SE ↑
So you're telling me that your Yaris ZR, which looks exactly like our Yaris SE, has drum brakes? Interesting as our SE has discs.
Yup! The bean counters here in Aus Toyota must have decided it wasn't worth it :(. The ZR has been the top of the line model since the first Gen 3 came out, and it's never had a disc brake rear end.
stidnamThread starterAustralia · Jan 25, 2019#26
Airbox has been purchased and is coming from a Toyota IST in Japan. Lucky enough to have all the pipe work and even an airflow meter (getting swapped out anyway).

Picture not included in this copy

Pretty much just the drive shafts left now to source, and a few odds and ends from Toyota.
stidnamThread starterAustralia · Feb 10, 2019#27
Well after a full days work on Friday, the donor Corolla is now stripped and engine is out. The engine pull was rather easy - no engine lifter needed. Just jacked the car up, then lowered the front back down just enough to rest the engine on a dolly, unbolted the mounts and wheeled it out :).

I've had a better look at the EC60 gearbox. The casing is a lot shorter than that of the C60, and based on what I can see, all the Yaris mounts I've purchased should bolt up. I actually need to check if the factory ZRE152 corolla side mount already fits. Doubt it, but I'll do a side by side comparison.

Picture not included in this copy

I'd love to be able to run that front mount as well on the Yaris. Ashame there's no provision for it.

I also checked the spline count on the drive shaft. I can confirm that it has 20 splines, further adding to my confidence that XD shafts will work with this gearbox. I'm now going to take a punt and just buy a set out of the US.

I don't expect anyone to believe that all of this will bolt straight in and clear everything until it's done. Regarding that point, I'm now contemplating the purchase of a written off Yaris to strip as well as test fit everything and get the exhaust and wiring all sorted for a full plug and play experience.
CrankyOldManWest Michigan · Feb 11, 2019#28
Looks like the clutch lines fit as well? Or is that still in the donor?
stidnamThread starterAustralia · Feb 11, 2019#29
Nah that's still in the donor before I dropped it out
stidnamThread starterAustralia · Feb 19, 2019#30
Small update and just a confirmation of previous assumptions

I can confirm the lower gearbox bracket for the Scion XD bolts to the bottom of the EC60 gearbox and all mounting holes are threaded on my EC60.

The GRMN side gearbox bracket also bolts to the EC60. This bracket is significantly different to the one for the ZRE152 chassis, as expected. Unfortunately though, it would seem that this bracket comes with small tab on the side that looks like it's used to clip a wiring loom on, and this fouls with the counter weight (?) on the shifter assembly. Guess I'll either bend it or chop it off all together pending actual installation. There's already a bracket on the gearbox to support the wiring loom that goes to the speed sensor.

Picture not included in this copy

Picture not included in this copy

Just needs LSD now ;)
stidnamThread starterAustralia · Mar 22, 2019#31
Just a quick update on a couple of things.

Driveshafts

I ordered left and right Scion XD drive shafts from the US, which turned up today. Unfortunately the wrecker either didn't inspect them correctly or didn't pack them well enough as the front right has a nice slit in the boot and was oozing CV grease all through the package.

As a side note, I really feel sorry for those of you who have to deal with snowy conditions and salt roads. These drive shafts looked as if someone had given them a bath in the ocean. Doesn't really surprise me given how much rot I see under cars subjected to salt roads :(

Anyway, I took the right hand shaft down to the drive shaft shop and we went hunting through what they had in stock that matched the same specs as the XD shaft. I had already done some research and had a pretty good idea. We ended up confirming that a ZZE122 2006 model Corolla was a perfect match (spline counts, shaft length, seal surface etc all seem to match). Based on my research, the left hand shaft is a match as well in length. It would have been nice to know this from the start, but hopefully it's good news for anyone doing the conversion here in Aus and wanting local options for drive shafts.

Shifter cables.

Overall good news on this front as well, but I fear I may have wasted some money in the meantime trying to work out my options. I ordered some shifter cables from a UK Yaris running a 1nr and EC60 combo. Total punt in hopes they fit. I received them the other week and have taken measurements against the Scion IM/Corolla cables I have. The bad news is I don't think they'll fit. I believe the 1nr/EC60 combo from the UK Yaris sits about 20 - 30mm closer to the firewall than what the 2zr/EC60 combo does. Unfortunately, the Scion IM/Corolla shift cables are around 70mm longer than the 1nr/EC60 combo and it's likely they'll just be excessively long.

To top it all off, the 1nr/EC60 cables don't latch into the shifter cage in the same way the Scion/Corolla cables do. If the 1nr/EC60 cables end up fitting, they'll most likely require me to buy the Euro spec shifter cage as well to properly secure them.

The good news is I found a company here in Sydney Australia who are able to make me up brand new shifter cables for around 200 AUD. That should enable me to supply them with the plate that seals the cables to the floor, and I should end up with cables that fit perfectly.

Hope this helps out someone in the future :)

Not long until there's no reason not to start pulling everything apart!
atomic_hojiKincardine, ON, Canada · Mar 22, 2019#32
Was just thinking about this recently!

Good to hear you're making headway. Ya, the salt use on the roads here makes wrenching more ... awesome? 🙄 Too bad about the buggered CV boot, but glad you got it sorted; and found an alternate source for the one side!

That's good news you are able to get shift cables made-up if need be, but too bad about that the other stock cables haven't worked out - unfortunate side effect of researching solutions. Have you had a change to measure how the stock Yaris cables compare? I guess until you pull it apart you won't be able to measure for sure.. lol We know they mate to the shift cage correctly since they're stock, but just wondering if the transmission end is compatible and how the length is comparatively; or you've already said and my brain is melted.. lol

Looking forward to seeing how you make out as you get everything installed.

-- Adam
stidnamThread starterAustralia · Mar 22, 2019#33
The ebay seller was really good about the shaft and refunded me the cost of that shaft. The refund will cover a reconditioned zze122 shaft, so no loss. Might even get the boot replaced on this shaft and keep it as a spare. Kind of erks me putting in shafts that look all rusty even though no one ever sees them.

I can say with good certainty that the factory 1nz/C50 shifter cables will be totally useless. The shifter setup on the C series gearboxes is completely different. I'm fairly confident I'll need custom at this point. The only other car that might have any remote chance of donating its shifter cables is a manual C-HR. Too much effort to try and find one being wrecked to even check.

Adam, as you point out, all this is just the cost of research right. I'm hoping it helps someone else out at the end of the day.

So literally the only things left to acquire are a new clutch and a quaife diff ;)
CrankyOldManWest Michigan · Mar 25, 2019#34
I feel your pain on the research costs. I bought 4 different C5x gearboxes when I was figuring out gear ratio swaps and which LSD goes in. I somehow bought the wrong LSD and had to pay a 25% restock fee. Ouch!

Really excited to see things moving along on this!
stidnamThread starterAustralia · May 5, 2019#35
*edit*

May have just jumped the gun here a little. I've been mapping the wiring for the conversion this weekend and thought I'd come across a problem with a difference in speed sensors, but does anyone know whether the speedometer signal on a gen 3 is fed off the wheel sensors as opposed to a gearbox sensor? I'm assuming it is.

I jumped to conclusions when I looked at the non-abs wiring diagrams and saw the speed sensor in the actual gearbox. Had me worried for a second there.
saikouguySydney, Australia · May 5, 2019#36
Awesome stuff. Judging from the photos you're based somewhere in Sydney/NSW. Can't wait to see the first 2ZR swapped Yaris/Echo in Australia.
stidnamThread starterAustralia · May 5, 2019#37
Yeah Sydney based. Never know, someone might beat me to it with the slow progress I'm making :)
saikouguySydney, Australia · May 5, 2019#38
Should jump on our Facebook groups and show your ride we're looking to do a meetup soon in Sydney.

'Vitz Club Australia' & 'Sydney Yaris / Vitz club'
BugeyeSydney · Oct 7, 2019#39
How is this going ??
stidnamThread starterAustralia · Oct 7, 2019#40
Progress has been slow. I've been preoccupied with other things.

I've purchased a new clutch kit and I've also purchased a Quaife ATB/LSD, but haven't had it installed yet.

I've finishing the mapping for all the wiring on paper and can throw that up if anyone is interested.

Next step is for me to purchase another Yaris at the salvage auctions so I can transplant everything in that shell and prove it'll all work before I rip a perfectly functional car apart :)

I'm also still exploring options for shifter cables. I'd like genuine ones, but having trouble getting a hold of any at a decent price. I still have the fallback option to get custom cables made up and will probably go that way.
CrankyOldManWest Michigan · Oct 8, 2019#41
Awesome! I'd be happy to look over the wiring diagrams if you want a second set of eyes on them.

Someone was asking in another thread about an LSD for the EC6X gearboxes. What model did you get?
stidnamThread starterAustralia · Oct 10, 2019#42
Thanks Cranky. I'll take you up on that offer. Will upload as soon as I find an appropriate format - currently in spreadsheet form at the moment. Have mapped the pin changes for the body side of the ecu loom as well as the fuse box connector. Everything looked fairly straight forward with some joining of common power and the addition of the corolla fan controller.

I've purchased a QDF29E. I have found someone here in Aus who has installed that centre in the exact same gearbox, so fairly confident in it fitting. I'd responded to that other thread as well and I'd put money on the centre fitting any ec6x box, but the cost of the centre warrants doing a little more research on that guys part.
stidnamThread starterAustralia · Oct 10, 2019#43
Here's the ECU body side mapping between the Yaris and the Corolla. The pins on the Yaris loom will need to be de-pinned and re-pinned to match the Corolla plug. I'll also have to add a new wire for the fan controller and run another circuit for that, potentially.

Picture not included in this copy

Here's the fuse box plugs for the corolla - two of them. The BA1 mapping column is the Yaris BA1 pin reference.

Picture not included in this copy

And here's the Yaris BA1 pinout that matches the Yaris BA1 reference in the previous image.

Picture not included in this copy

Ignore the colours on the last two images. They were just my way of checking off what I'd already matched.

Disclaimer - for anyone thinking about using the above, please do the mapping for yourself. I haven't proven this mapping to be correct. Also this mapping is specific to a 2012/13 Australian spec Yaris and 2012 Australian spec Corolla. Also I understand my labeling of source and destination will technically not be correct if you consider the power source to be the true source. Don't over analyse it ;)
CrankyOldManWest Michigan · Oct 10, 2019#44
That's definitely the right way to do this. The good news is that the fuse box connectors are simple enough to swap using a very small needle/pin and a watchmaker screwdriver. The ECU smaller pins are much harder to remove without damaging them.

I found a video that has a neat trick for being able to take them out without the crazy tiny tool that would otherwise be required: https://www.youtube.com/watch?v=9uW-QeclHmU
stidnamThread starterAustralia · Oct 10, 2019#45
Sweet! Thanks for that. I had been wondering how to de-pin that connector. I'd picked up the body harness from the Corolla to play with, saw the locking tabs, and then decided it was all too hard in the moment and then put it away for another day. Pretty straight forward once you get that pin cover off though!
stidnamThread starterAustralia · Oct 13, 2019#46
I tested fitted some 17" MX5 ND wheels today (fronts). Unfortunately the 215/45 R888s scrub the inner front guards pretty bad :(. The size, surprisingly, actually suits the car well in my opinion. Might investigate some 205/45 rubber. Has anyone run 205/45R17 with a +45 offset without scrubbing inner guards?

Picture not included in this copy

On a completely different topic, I'm also keen to get some feedback from those who have done the 2zr conversion - given the Engine ECU dictates the throttle curve, did you notice better throttle response when switching from the 1nz to 2zr? Rev matching on the downshift is so frustrating with how the factory throttle curve is programmed. The first 15% of the throttle does nothing, and the rest of the throttle feels like stepping on a wet sponge.
myfirstyotaToronto Canada · Oct 13, 2019#47
I noticed better throttle response but i also installed a lightened flywheel so my opinion probably doesn't mean much.

Im also using the Xd trans with different gearing..
06YarisRSFredericton, New Brunswick, Canada · Oct 13, 2019#48
I don't know that I can weigh in on the throttle response thing either with the Scion xD ECU and turbo. But, before I modified the 2ZR, it seemed more responsive than the 1NZ.
3rdSEmanMontreal - Canada · Oct 13, 2019#49
205/45R17 Pilot Sport A/S 3+ on RPF1 17X7 ET43 & stock 2012 SE suspension clears nicely all around no rub

1 attachment not included in this copy

stidnamThread starterAustralia · Oct 13, 2019#50
Champion! Thank you! Close enough to make me start seriously looking for tyre options.

Thanks guys for the feedback on the throttle. I'd been speculating that Toyota put a pretty big curve in the Yaris throttle given the target market and type of car it is. I still need to investigate pedal options as well. The height and spacing of this pedal in relation to the brake is horrid.