Yarisworld Archive

3rd gen 2zr swap with 6 speed

97 posts · 124,228 views · page 2 of 2

Replies continued

CrankyOldManWest Michigan · Oct 15, 2019#51
Originally Posted by stidnam ↑
The height and spacing of this pedal in relation to the brake is horrid.
Agreed. They definitely were not looking at making it easy to heel-toe on this setup.
stidnamThread starterAustralia · Nov 3, 2019#52
I happened to be in Tokyo this week and stopped in at one of the Autobacs. To my surprise I found they stock Neoplot pedals. It was a little on the expensive side, but thought I'd give it a punt. The position looks better than stock - 20-30mm higher off the floor and a touch to the left.

I'll install it in the coming weeks and provide some feedback as to whether it was worth it.

Picture not included in this copy

Picture not included in this copy
BugeyeSydney · Nov 10, 2019#53
Cool mate. Thanks for the update.
I’m still going to attempt mine eventually, but scared of wiring. Might go haltech (mmmaaaaayyybbbe)
stidnamThread starterAustralia · Jan 6, 2020#54
Just a small update. The latest MCM video provided a little motivation and I thought it was about time I made some progress. So I went and bought another Yaris..

Picture not included in this copy

The plan is to strip the motor and gearbox out of this one so I can test fit the 2zr and EC60 into this chassis, wire it all up, sort the shifter cables and exhaust, and then transplant it all into the other Yaris.

Soo...anyone in Sydney want to buy a 1NZ motor? :)
ern-dizCA all day · Jan 7, 2020#55
Nice!
06YarisRSFredericton, New Brunswick, Canada · Jan 7, 2020#56
Originally Posted by stidnam ↑
I happened to be in Tokyo this week and stopped in at one of the Autobacs. To my surprise I found they stock Neoplot pedals. It was a little on the expensive side, but thought I'd give it a punt. The position looks better than stock - 20-30mm higher off the floor and a touch to the left.

I'll install it in the coming weeks and provide some feedback as to whether it was worth it.

Picture not included in this copy

Picture not included in this copy
Oooh. Lovely looking piece of hardware there! I bet that would feel fantastic underfoot.
stidnamThread starterAustralia · Jan 7, 2020#57
Yeah it's a lovely looking piece of work :)

Unfortunately I haven't installed it yet. I'll be ripping the accelerator pedal out of this new Yaris and swapping it onto that pedal before installing it in my car. After driving a manual corolla over the Christmas break, it's really highlighted how bad the pedal positions are in the Yaris. I may even take the blow torch to stalk of the pedal to try and move the position a further 10 - 20mm closer to the brake pedal.
mitch9521Red Deer, AB · Jan 12, 2020#58
Following this thread closely, as far as I know you are the only one tackling a 2ZR-FE on a 3rd gen. So far it doesn't seem much different than doing the swap on a 2nd gen Yaris/Vitz
stidnamThread starterAustralia · Apr 26, 2020#59
More progress today. Motor and gearbox have been test fitted to my spare shell and I've wired up 99% of the fuse box connector. What I can confirm so far
  • Motor and box mount perfectly using the GRMN Yaris mounts
  • The GRMN gearbox mount has a wiring harness tab on it that fouls on the counter weight of the gearbox selector. This needs to be bent out of the way
  • The cables I obtained from the euro 6 speed yaris do fit, but really aren't long enough. Shifter cables will need to be custom made
  • The Yaris battery tray no longer mounts properly on top of the gearbox mount. Mounting holes will need to be slotted
  • Exhaust looks like it lines up nicely, so I'll be grafting the Corolla exhaust to the Yaris one

Now on to the wiring
  • Factory Corolla starter wire does not reach the positive terminal where the Yaris battery fits. This will need to either be re-routed or extended
  • 99% of the wires in the Corolla fuse box plugs terminated nicely into a brand new Yaris 26 fuse box plug. The only exceptions are the starter trigger, which is too big, and the wiring for the ignition coils and fuel injectors - these are two separate wires in the corolla loom that share a common terminal in the Yaris. It's a tough squeeze to get both wires in the Yaris plug. If running bigger injectors in the future, I'd actually run a separate circuit off this wire, using it as a trigger.
  • Remember not to remove the secondary lock tab completely from the Yaris fuse box connector as the first row of pins are actually inserted through the secondary locking tab 😳
  • There looks to be a single redundant brown wire in the corolla loom. I couldn't find this in the wiring diagrams. After running a few checks I confirmed it to be a ground wire
  • There's a second fuse box plug in the Yaris. This plug seems solely dedicated to the heated oxygen sensor where the wiring goes back into the cabin and back out the floor to the exhaust. The Corolla does things differently and this wiring is all part of the engine loom. Therefore, it looks like this plug will be left empty per the photo below.
  • After plugging in the ECU and connecting up the computer, the software now recognises the 2ZRFE ECU even without connecting to the car. Running the diagnostic over it though and it's coming up with errors against MAF, Air temp, and immobiliser. Nothing too surprising as MAF wasn't plugged in, neither was the Oxy sensor in the exhaust, and the immobiliser is a given until the ECU is registered.

That's it for now. Next steps will include getting shifter cables made up, grafting the Corolla exhaust to the Yaris one, and finishing off the wiring odds and ends.

Picture not included in this copy

Picture not included in this copy
CrankyOldManWest Michigan · Apr 26, 2020#60
Awesome work!!
saikouguySydney, Australia · Apr 28, 2020#61
Exciting stuff can't wait to see it. Maybe in person would be great 😉
stidnamThread starterAustralia · Apr 29, 2020#62
Originally Posted by saikouguy ↑
Exciting stuff can't wait to see it. Maybe in person would be great 😉
Still a little way off dropping the motor into my daily.

While installing the motor on the weekend I also noticed the 2zr water pump had been leaking. Seems to be a common problem so will be replacing that while I'm at it. I'm also thinking about putting the spin on oil filter adapter while I'm at it.

And...after investigating custom shifter cables, I'm now investigating options to buy the genuine Toyota cables. Could be a long wait.

Oh, and I'll have to re-upload new images of the wire mapping. There are some errors in my previously posted images.
stidnamThread starterAustralia · May 25, 2020#63
Small but exciting update. I've managed to get my hands on genuine GRMN shifter cables that match my gearbox. Buying genuine ended up costing the same as what custom cables would have.

Note, these cables are made in Belgium. No surprise there given where the GRMN Yaris is assembled (France).

The cables are around 30mm longer than the ones I'd purchased from the UK that were from the 6 speed diesel Yaris. Not surprised either given the 2zr is mounted forward and down.

In other news, the ZRE152 computer appears to be incompatible with the 3rd Gen systems. More to come on that, but doesn't look like I'll be using the original engine I bought.

Picture not included in this copy
spoonzzMelbourne, Australia · Aug 22, 2020#64
Any updates with this? So keen to see your progress. I'm also in Aus and own an auto 2012 Yaris YR and wanting to do something similar one day. Good luck!
ikentySt. kitts & Nevis · Oct 4, 2020#65
You are an inspiration to me.
I am on my second vitz now. I had a NCP13 Vitz RS now I have NCP91 Vitz RS.
My plans were to swap a 2zr engine and use my extra 6 speed transmission from my AE111 Levin for better acceleration but then I realized that the 2zr transmission bolts up to the 1NZ engine so now I am trying to confirm if the mounting points for the C50/56 NZ/ZR is the same as the C66/EC6x boxes.

Thanks.
Kimo
stidnamThread starterAustralia · Oct 5, 2020#66
Glad I'm inspiring someone :)

You'll likely find that the chassis mounting points for the C5X and C6X boxes will be pretty similar or at least have bosses in the right spot to tap. Would pay to do your research though.

The EC6X boxes will unlikely bolt in to the NCP9X or NCP13X chassis while mated to the 1NZ unless you went custom mounts. I was mulling this over myself when I found out my 2ZR was going to be incompatible with the NCP131 - I wanted to make sure I could still use my EC6X box with the Quaife. However, I've since acquired yet another Corolla/Scion IM, which I know for a fact will work, and am now in the process of piecing all that together. The 2zr dream lives on.

For the record, anyone considering doing a 2ZR swap in to a 3rd gen should probably think twice before committing to it. You must use a 2ZR and some of the other gear from a ZRE18X (Corolla/Scion IM). It's no where near as simple as the NCP9X swap.
CrankyOldManWest Michigan · Oct 5, 2020#67
Originally Posted by ikenty ↑
... I realized that the 2zr transmission bolts up to the 1NZ engine so now I am trying to confirm if the mounting points for the C50/56 NZ/ZR is the same as the C66/EC6x boxes.

Thanks.
Kimo
That's a good question. I'm pretty sure that the EC6X gearbox requires completely different brackets from the C5X gearboxes. The casting is two pieces, not three and has a different configuration for the shift lever. It might require sourcing mounts from Europe or Japan to use the EC6X. Please let us know (in a new thread) what you find out!
CrankyOldManWest Michigan · Oct 5, 2020#68
Originally Posted by stidnam ↑
For the record, anyone considering doing a 2ZR swap in to a 3rd gen should probably think twice before committing to it. You must use a 2ZR and some of the other gear from a ZRE18X (Corolla/Scion IM). It's no where near as simple as the NCP9X swap.
Correct. I recently looked at a 3rd gen in the local junk yard and it's a very different animal from the 1st/2nd gen (which are basically just cosmetic refresh siblings). The electrical system is laid out differently, has a different fuse/junction box under the hood, different wire harnesses, etc. etc.

What did you find out with the LSD in the EC6X gearbox?
stidnamThread starterAustralia · Oct 5, 2020#69
Originally Posted by CrankyOldMan ↑
Correct. I recently looked at a 3rd gen in the local junk yard and it's a very different animal from the 1st/2nd gen (which are basically just cosmetic refresh siblings). The electrical system is laid out differently, has a different fuse/junction box under the hood, different wire harnesses, etc. etc.

What did you find out with the LSD in the EC6X gearbox?
I have a Quaife ATB installed in my EC6X. I had that installed about 6 months ago along with having a bunch of the synchros replaced. While it's not technically an LSD as such, it does a very similar job and in my opinion will be more streetable than a traditional clutch pack LSD.

The last few months have been frustrating to say the least when I found out that the older 2ZR ECU was simply not compatible with the 3rd gen systems. While it would have driven, there would have been multiple systems and sensors that would not have functioned. Funny, the immobiliser did register with the ECU, but that was about the only good news. Therefore, I started mulling over whether to try and install the EC6X with the 1NZ. I didn't spend too much time on that though.

I'm now onto a 2013/2014 Corolla that comes with an updated ACIS based intake manifold. We got that version here in Aus while you guys in NA got the Valvematic version. Unfortunately for me, the ACIS manifold is another 30%ish larger and doesn't clear the radiator fan shroud. There are workarounds and I'll have to do a complete write up here when I have the conversion sorted.
CrankyOldManWest Michigan · Oct 6, 2020#70
Which model Quaife? I've got the QDF15E in my hatch. The track car (Project 2ZR Vios) has a Cusco clutch pack and it's too aggressive for daily/street use in my opinion. Lots of clunking and banging at low speeds before it gets warmed up.

Is the ECU just a matter of pins being in the wrong place or are there whole systems that are electrically incompatible? I forgot to look at the connectors when I was at the junk yard last month.

Any chance you've looked at a 3ZR swap? Looks like you may have access to the 3ZR-FE, we only have the 3ZR-FAE.
stidnamThread starterAustralia · Oct 6, 2020#71
The Quaife in mine is a QDF29E. How's your experience with the Quaife been? This will be my first FWD car with one. I'm hoping for a noticeable difference. Even on the street, and especially in the wet, I find the Yaris struggles with traction (195 tyres).

Regarding the ECU differences, unfortunately it's not just a matter of the pins being different - I'm having to build a little patch harness to get around that problem. Even with a ZRE18X ECU, while the dash cluster will work correctly, the Yaris ABS unit won't talk with the ZRE18X ECU. The ZRE18X ABS unit must be used to overcome this problem (Credit goes to another mate of mine for solving that one). Even Adam, who did the Valvematic conversion, had the same issue.

I have investigated the 3zrfe conversion and it's tempted me on multiple occasions. We got the 3zr in our Rav4, which conveniently came in manual transmission as well. While I think it'll work, I just can't justify it. The cost of the motor is twice the price of a 2ZR. There's also some trade offs it would seem - you sacrifice rpm for a longer stroke, more torque, and that torque band moved further down in the rpms. I think it'd make for a great little round the town car with the extra torque, but I'm not convinced it'd be as fun in the hills and on the track. Change my mind though :) it's not too late.
CrankyOldManWest Michigan · Oct 7, 2020#72
I've been very happy with it. No noise, very good traction in the snow and on ice with appropriate winter tires. Not torque steer on hard acceleration. Wet roads are still not great but it's better than an open diff for sure.

Aah, that's a bummer. I work in automotive and see that kind of incompatibility all the time, even on revision changes within a product family. I made a spreadsheet to verify the Yaris and xD ECU pinouts and they're basically identical. The Corolla is way off and requires a lot of pins to be moved/added/deleted but in theory would work. Our workaround for the speedo was to use the C50 turbine and add the wires into the xD harness (since the xD uses the ABS sensors and CAN to send the speedo signal to the cluster). If your differential can use the OEM speedo driving gear and your casting has the hole for the turbine in it, you may be able to go that way.

ArmstrongRacing and I had talked about the 3ZR lower/long block as a potential "stroker kit" for the 2ZR, mostly because we only have the -FAE head and that requires a LOT more work to make it run on the Yaris platform. I hadn't considered the tradeoff of stroke length (which is where the extra 200 cc's come from) vs RPM and where the torque falls in the power curve. For race applications, it might be better to keep the torque and power peaks closer together. My racing class would also require additional weight if I went to the 2.0L engine, possibly negating or negatively offsetting the 10-15 bhp gains. And I'd have to use the FAE head, so that's probably not happening.
stidnamThread starterAustralia · Oct 7, 2020#73
Yeah I had my spare Yaris shell all wired up pretty quickly. Only had to move around 10 or so pins to make it work. I was so sure it was going to work simply because all the ECU plugs were the same. However, when you look a little closer, all of the 3rd gen Yaris systems and general build of the vehicle more closely resembles that of the Scion IM rather than the XD. Modifying cars was a lot easier before the days of CANBUS :S

For the ZRE18X swap I've purchased some sumitomo plugs that will take the existing Yaris ECU pins and will then allow me to crimp the pigtails of the ZRE182 ecu plug so I can build a patch harness and avoid chopping anything up. The only real difference in wiring then is that the there's no ELS1 on the ZRE18X, the thermos are controlled via the RFC pin, and the +BM wire goes to the larger ECU connector instead of the smaller one on the Yaris. In saying all that, your conversion in NA is more complicated due to that Valvematic system :(

The speedo won't be a problem. I just wrecked a ZRE18X and pulled the ABS actuator out of it. I'll be swapping that in when I do my conversion along with a new master cylinder and reservoir to clear the top of the engine.

Yeah I'd love to have a drive of the 3ZR in a Yaris before committing. I do think it'd make a big difference around town with it's torque band, but I'm just not convinced for the price. If you were simply using the block though with a 2ZR head and a piggy back management system....that might be worth it.

For anyone interested in the quoted numbers that each engine makes

ADM 1NZ = 81kw @ 6000rpm and 141nm @ 4200rpm
ADM 2ZR = 103kw @ 6400rpm and 173nm @ 4000rpm
ADM 3ZR = 107kw @ 6200rpm and 187nm @ 3600rpm

So the 3ZR comes in at 8% more torque at 400rpm earlier when compared to the 2ZR. That's where you'd notice it, but I speculate that the 3ZR wouldn't rev as easy as the 2ZR. The power gains are negligible and I think you end up with a slightly lower redline with the 3ZR.
CrankyOldManWest Michigan · Oct 7, 2020#74
I agree about wanting to drive it before committing to it but there's no way to do that around here. You could at least drive an Altis to see what the engine feels like in general. =)

The other problem would be that I'd have to add another 270 lbs of vehicle weight to be able to run that displacement in the class I'm building for. That also ignores the fact that I'd have to use the FAE head and deal with the valvematic shenanigans, so it's pretty much right out for that line of inquiry. For a streetable daily driver it would be an interesting project, if only for posterity.
stidnamThread starterAustralia · Oct 7, 2020#75
Yeah sounds all too hard and not really worth it at the end of the day. After having driven a 2ZR Yaris, I think I'll be happy with that. I'm most looking forward to having the EC60 gearbox and Quaife though. That actually excites me more than the 2ZR. The shifter and clutch feel is so much nicer than the Yaris setup. I'm anticipating that it'll feel like a completely different car when I'm done.
stidnamThread starterAustralia · Nov 2, 2020#76
I've slowly been gathering the parts required to do this whole thing in one weekend (fingers crossed). Because the ZRE18X ECU runs completely different plugs to the ZRE152/XD/Yaris ECU, it's necessary to either solder or build a patch harness.

I didn't like the idea of soldering close to 30 wires or the idea of chopping all my current wiring. Not that I'm ever going to reverse this conversion, but I hate the idea of irreversible modifications. So I went out and bought all the plugs I'd need to build a harness to go from the existing Yaris ECU pins to the ZRE18X ECU plug.

Picture not included in this copy

Connectors and terminals are all readily available from Japan and only took a couple of hours to crimp up.
spoonzzMelbourne, Australia · Nov 2, 2020#77
So excited to see your progress. I need to find a manual Yaris one day!

Where did you learn all this knowledge by the way? Just researching and trying things on your own?
stidnamThread starterAustralia · Nov 2, 2020#78
Originally Posted by spoonzz ↑
So excited to see your progress. I need to find a manual Yaris one day!

Where did you learn all this knowledge by the way? Just researching and trying things on your own?
Hundreds of hours of research and thousands of dollars in mistakes :). The Yaris is good like that for someone starting out. It's simple and cheap.
stidnamThread starterAustralia · Nov 24, 2020#79
Finally got around to doing the conversion. Not finished yet as I need to sort out exhaust and an overflow bottle. However, it starts!

The patch loom seems to have worked a treat and fuse box just needed repinning. So no soldering required.

Picture not included in this copy
CrankyOldManWest Michigan · Nov 24, 2020#80
Congrats! Feels great to have it running again, I'll bet!
stidnamThread starterAustralia · Nov 25, 2020#81
Feels good knowing it's all going to work. Doesn't feel as good that it's still not driving and I don't yet have a solution for the exhaust.

So close yet so far.

Picture not included in this copy

I've just got to have patience. The whole conversion took me a lot longer than I expected. I think I spent a solid 4 - 5 hours wiring it up on the weekend

Also, these are totally amazing - https://www.hi-1000ec.com/product-list/85 makes splicing so much easier vs soldering. They are also what you'd ordinarily find in a factory loom where Toyota have had to splice wires together.
CrankyOldManWest Michigan · Nov 25, 2020#82
I think I used the first few feet of a Corolla exhaust to make mine, just past the first catalytic converter. The rest was custom bent and welded up by a "guy I know" mechanic. If you have to pass emissions testing, that may require some more creative/expensive solutions.
spoonzzMelbourne, Australia · Nov 26, 2020#83
Congrats! You'll have it running 100% soon. Often, I wish I didn't have a 2012 automatic yaris because of this thread haha.
stidnamThread starterAustralia · Nov 30, 2020#84
@spoonzz, you can always manual swap yours ;)

Corolla exhaust is partially hooked up and I've run the car for a period of time now. Seems to be working well. I was actually surprised that it all worked first time. Guess I should have trusted all that time I put into the wiring.

I've kept the Corolla fan controller and the only thing remaining there is to create a lead that goes from the Yaris fan to the Corolla fan controller and then permanently earth the Yaris fan relays.

I had also purchased an 86 shift knob to match the new shift pattern of the rolla box, but unfortunately it stops the reverse lockout from being raised. Problem solved now as I'd always planned on running a short extension to address the horrible height of the factory shifter.

Picture not included in this copy

Oh and engine cover also fitted now :)

Picture not included in this copy

And yes, the whole front is actually back together again now.
CrankyOldManWest Michigan · Nov 30, 2020#85
Glad to hear it's still coming along!

I'm afraid I can't tell what changed on the shifter. My 6-speed still has the Yaris shifter base, no reverse-lockout involved on that one and there's enough play in all directions to reach reverse on the left.
spoonzzMelbourne, Australia · Dec 1, 2020#86
I wouldn't know where to start! You do it for me, I'll pay you hahaha

What's left for you to have the car road worthy? I assume the exhaust and meeting some standards such as emissions?
stidnamThread starterAustralia · Dec 1, 2020#87
@spoonzz, emissions won't be necessary. Using stock exhaust and Corolla cat. All it needs is the exhaust welding up now, which I'm hoping I'll get to by the end of the week.

LOL I am not in the business of engine conversions sorry :). You can have my wiring diagrams and all that work. Actually, here you go. For future reference > 2014 Corolla to 2012 Yaris fuse box wiring

Picture not included in this copy

@Cranky, that shifter in my photo is a zre182 shifter with the lockout. I've thrown a 50mm extension on the end of it though so the knob clears the reverse lockout. I'm used to driving around with a 20cm shift knob. It's a little excessive, but the Yaris factory position is way too short in my opinion. 50mm increase should be a nice compromise.
spoonzzMelbourne, Australia · Dec 1, 2020#88
Hahah, it was a joke (mostly :P)

Thanks for the diagram. I have saved it. By any chance will you be doing a short summary or write up after everything?

...please say yes
stidnamThread starterAustralia · Dec 8, 2020#89
Here's the summary
- 2012 - 2014 Toyota Corolla MT parts
* Engine with all ancillaries
* Gearbox
* Flywheel and clutch
* ABS actuator
* Front exhaust pipe and Oxy sensor
* ECU
* Engine loom
* MAF
* Shifter cage and shift knob
* Small ECU plug that runs to the fuse box
* Radiator fan controller with plugs
- Toyota IST/Scion XD airbox and intake pipe
- GRMN Yaris engine mounts and shifter cables
- NZE141 brake master reservoir
- ZZE122 Corolla drive shafts
- Toyota IST/Scion XD radiator and heater hoses and filler neck
- Generic ebay overflow bottle
- 2019 Yaris ECU mounts

Optional for fuse box wiring and patch loom
- Spare fuse box plug to avoid butchering the one off the 1NZ loom
- 2x 13 pin Sumitomo TS 025 plugs with terminals (matches smaller sized ECU terminals)
- 1x 6 pin Sumitomo TS 090 plug with terminals (matches larger sized ECU terminals)
- 1x 2 pin Sumitomo TS 090 plug with terminals (for terminating the FANL wire and routing the +BM wire from the fuse box to the ECU)
- Set of Hozan P706 crimpers

The conversion is done now and the car is back on the road. AC was re-gassed today.

Everything seems to be working well and it drives pretty much like a Corolla. I've got an unusual clutch squeal when the clutch disc engages. Not sure what's causing it as everything was machined and cleaned prior to installation. I'll have to keep my eye/ear on it and fingers crossed it goes away itself.

While I've had to do a lot of research, the actual conversion was pretty straight forward and I've been impressed that everything has worked straight off the bat.

I have to be honest, this swap isn't going to blow you away. It's a noticeably quicker car now, but I feel that's mainly due to the bump in torque. The torque has made it more driveable - can cruise around in 3rd and 4th gear without having to drop back all the time, and the take off from the lights is a lot easier. Give me a few more days though and I'm not even going to remember what the 1NZ was like.

The EC60 box out of the Corolla is a nicer box than the factory Yaris 5 speed. Shift feel is improved, but first gear is way too short. Frustratingly short. It's pretty much there to get you off the line and then you hit second. In this regard, it'd probably be better off looking at a C5X box with better ratios. However, the Quaife is amazing. Totally worth doing.

There is one thing that really feels like a step back from the 1NZ - the rev hang that comes with the 2ZR. It's so much worse than the 1NZ in the 3rd gen Yaris. I thought I knew what rev hang was, until I drove the Yaris with the 2ZR. You get used to it, but I feel the EC60 ratios exacerbate the problem. If I were doing this over again, I'd consider getting a light weight flywheel to try and help the problem. Though I think a lot of it has to do with the ECU programming.

In summary, if you want to know what it's going to be like to do a 2ZR conversion to a Yaris, go and drive a manual Corolla to get a feel for the motor and gearbox, then go drive an 86 to get a rough idea of how quick the car will feel (give or take).
CrankyOldManWest Michigan · Dec 8, 2020#90
Congrats! So glad you've got it back on the road and were able to work out all the details. It's good to get feedback on the EC60 vs the C50 since I've been considering sourcing one for my 2ZR daily driver. Seems like a lot of work for minimal gains, possibly even a net loss.
stidnamThread starterAustralia · Dec 9, 2020#91
Yeah pretty happy with it so far and still kind of surprised that everything worked with no error codes popping up.

Regarding the EC60 box. Here's my list of pros and cons for anyone considering one, and I'd strongly suggest driving a Scion IM/Corolla before committing.

Pros
- Good shift feel
- Easily accessible in Australia
- Quaife diff available
- The only 6 speed box that's going to bolt into a Yaris without modification to the chassis rail
- Perfectly fine for every day driving
- It's not an automatic LOL

Cons
- Requires custom or GRMN shifter cables
- Requires GRMN gearbox mount
- Short first gear (I find myself changing at around 20 - 25km/h)
- Concentric slave cylinder - which can actually be a positive for pedal feel
- High clutch engagement point
- Limited to no heavy duty clutch options
- Limited aftermarket flywheel options
- 6th gear ratio isn't really any better than the 5th gear ratio in a 5 speed box. You're just getting one extra gear jammed in the mix.
- No short shifter options or upgrades for the shifter cage

I do know about the MWR options for clutches and flywheels. Though expensive options for Australia and I'd rather try and use the OuterPlus flywheel from Japan vs the MWR option. Though I wasn't about to drop $1000 on a flywheel :)
CrankyOldManWest Michigan · Dec 10, 2020#92
That's some good solid feedback on the 6-speed. I discovered the same thing when researching gear ratios for my custom 5-speed build (almost a decade ago?!?) and decided that it wasn't worth the hassle of notching the frame. That said, Project 2ZR Vios has that done and the 6-speed is absolutely worth it on the track.

That's a lot of weight to ship all the way around the world, for sure. I live only a few hours away from MWR and basically get overnight shipping for the price of 3-day ground. =)
stidnamThread starterAustralia · Dec 10, 2020#93
I did some research last night into the ratios and interesting to see that the Lotus EC60 runs a 4.3x final drive with slightly different ratios on 4th, 5th, and 6th I believe. However the first few gears are the same. This is in comparison to the Corolla's final drive of 4.5x (can't remember the exact last number).

I think I would have preferred the 4.3 final drive in the Yaris. Ashame.

The other thing to note though is that in theory, any upgrades for the Lotus Elise S3 gearbox should equally apply to the EC60. Gearsets etc...however everything I've seen has been extremely expensive.
RagnaCaTVillalba, Puerto Rico · Dec 31, 2020#94
Originally Posted by stidnam ↑
I did some research last night into the ratios and interesting to see that the Lotus EC60 runs a 4.3x final drive with slightly different ratios on 4th, 5th, and 6th I believe. However the first few gears are the same. This is in comparison to the Corolla's final drive of 4.5x (can't remember the exact last number).

I think I would have preferred the 4.3 final drive in the Yaris. Ashame.

The other thing to note though is that in theory, any upgrades for the Lotus Elise S3 gearbox should equally apply to the EC60. Gearsets etc...however everything I've seen has been extremely expensive.
Hi, it's been a while since I have posted but wanted to ask about that EC60 is that that newer 6 Speed? Currently I'm working on a celica C60 transmission dropping the internals into a Yaris gearbox.
stidnamThread starterAustralia · Jan 1, 2021#95
Yes, it's the newer generation 6 speed when compared to the C60. It does however have a really short first gear. First and second ratios could have been a bit longer. There are a number of variations of the box with difference ratios, but we only got the one here in Aus.
saikouguySydney, Australia · Jun 29, 2021#96
Is it possible to swap bellhousings on the EC and C series boxes? It'll be a great option if they can as you mentioned it being smaller and probably more plentiful
stidnamThread starterAustralia · Jun 29, 2021#97
Originally Posted by saikouguy ↑
Is it possible to swap bellhousings on the EC and C series boxes? It'll be a great option if they can as you mentioned it being smaller and probably more plentiful
Doubtful. What are looking to do? swap the EC box onto a 1NZ or 2NZ? If you want to upgrade the box on a stock Yaris, I'd look into gutting the existing box to replace it with different gearing and an LSD as well. The EC box isn't really worth it. Ratios are not great.