Yarisworld Archive

Paint Booth for Full Respray

104 posts · 591,793 views · page 1 of 3

06YarisRSOriginal postFredericton, New Brunswick, Canada · May 26, 2018#1
I've started the booth in my garage. Hoping to be done by mid-week. I bought 2 20" box fans and 6 furnace filters. Next is to procure lighting. I'm hoping to pick up used fluorescent fixtures and have a lead on a few 48" ones.

I built the frame so that it could be easily disassembled and stored. Each wall is screwed and glued with construction adhesive and each wall is detachable. I used strapping for cost savings. It's actually very solid. Once done, the entire thing will be covered in heavy poly sheeting and sealed with Tuck Tape.

Approximate dimensions of the booth are 19'(L) x 12'(W) x 7'(H). There is decent room all around but I wouldn't want to try painting a car much bigger in there.

I am leaning toward a negative pressure set up. I think that with the two fans and 6 filters, I should be able to evacuate the fumes/overspray quite quickly. I am going to rig up cups for the back of the fan motors to eliminate airborne material from going through the motor. However, I will probably experiment with a positive pressure system before making a final decision.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Replies 103

ezhacker1San Francisco · May 26, 2018#2
For a canopy tent setup spray booth my friend and I did. I cut up the box that the air mover fan came in and put filters all around. and vented the air out. Looking forward to see what you make. Jealous of the spacious room.
RunethecursedSocal · May 26, 2018#3
From watching certain youtubers on positive ventilation, youd want the fans to have an after filter to catch stuff and even then... Ive seen better results with just a negative vent set up as the positive air tends to blow particulate on the paint.
zoidberg444Birmingham, UK · May 27, 2018#4
Nice. Can't wait to see your results. I may have to do this to my car sooner or later with all the dents and scratches. The clear coat is coming off around a dent/scrape under the petrol cap.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 27, 2018#5
Originally Posted by ezhacker1 ↑
For a canopy tent setup spray booth my friend and I did. I cut up the box that the air mover fan came in and put filters all around. and vented the air out. Looking forward to see what you make. Jealous of the spacious room.
Since I've never done this before, I'm really interested in your experience. Would you mind sharing more details such as what type of fan(s) you used, positive pressure system or negative, type of filter, how well the tent evacuated the paint mist etc. The more details/observations, the better, if you're willing. Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 27, 2018#6
Originally Posted by Runethecursed ↑
From watching certain youtubers on positive ventilation, youd want the fans to have an after filter to catch stuff and even then... Ive seen better results with just a negative vent set up as the positive air tends to blow particulate on the paint.
My main concern is evacuating the paint fumes/mist. The thought of being in a room that is full of toxic and potentially explosive fumes makes me nervous. I just feel that a negative pressure system will get the stuff out of there quicker. My theory is that the higher the concentration of paint vapours to O2, the higher the risks associated. I have two box fans and when I'm done, basically 1/4 the back wall will be a filter. I also have 2 pieces of 32" x 45" furnace hammock filter and will likely use it to cover the 6 filters for added filtration. That's 20 square feet of filtered intake and about 6 square feet of exhaust. I will play with the configuration until I get the best flow rate with maximum air removal and an acceptable pressure - aka not too much suction on the walls. Since I'm doing a base coat/clear coat, a few small dust particles are a minor concern. I will likely be wet sanding and polishing the clear afterwards anyway.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 27, 2018#7
Originally Posted by zoidberg444 ↑
Nice. Can't wait to see your results. I may have to do this to my car sooner or later with all the dents and scratches. The clear coat is coming off around a dent/scrape under the petrol cap.
Haha, well it's definitely an experiment. I'll try to control the variables that I can (sealing, ventilation, cleanliness, applying what I'm learning about painting etc) and those which I can't (skill, experience), I'll just have to hope for the best. LOL!
zoidberg444Birmingham, UK · May 27, 2018#8
Originally Posted by 06YarisRS ↑
Haha, well it's definitely an experiment. I'll try to control the variables that I can (sealing, ventilation, cleanliness, applying what I'm learning about painting etc) and those which I can't (skill, experience), I'll just have to hope for the best. LOL!
A trick i heard about with painting in a non ideal space is to get it really warm and then spill a few gallons of water on the floor to make it humid to try and drag some of the dust out of the air.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 27, 2018#9
Originally Posted by zoidberg444 ↑
A trick i heard about with painting in a non ideal space is to get it really warm and then spill a few gallons of water on the floor to make it humid to try and drag some of the dust out of the air.
Interesting. I've definitely heard of wetting the floor to keep the dust down.
atomic_hojiKincardine, ON, Canada · May 27, 2018#10
Can't wait to see how this turns out, but so far it looks like you're on your way to an awesome setup. 👍

I've done a few little paint projects with a basic HVLP setup in the garage. Regarding fans, I would imagine that you're best to to set the fans to draw through the filters and blow directly out of the garage - filter catches the particulate and you get the vapours right outta there. The trick of getting the floor damp does seem to help keep dust from getting kicked up by either a fan or the air from the paint gun if you happen to blow past.

That said, don't forget that if you're going to go through all the work of setting up a good paint environment that you'll need a decent quality filter / dryer on your air setup - the old beast of a compressor might leave oil in the air and I imagine your humidity is probably like ours (high, and miserable in the summer, lol) so there's a chance of water accumulation in the tank - both will impact your paint quality if they get pushed through the gun.

Of course, goes without saying, airflow and filters or not, please get the proper organic vapour P100 cartridge half-mask. 👍

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · May 28, 2018#11
Originally Posted by atomic_hoji ↑
Can't wait to see how this turns out, but so far it looks like you're on your way to an awesome setup. 👍

I've done a few little paint projects with a basic HVLP setup in the garage. Regarding fans, I would imagine that you're best to to set the fans to draw through the filters and blow directly out of the garage - filter catches the particulate and you get the vapours right outta there. The trick of getting the floor damp does seem to help keep dust from getting kicked up by either a fan or the air from the paint gun if you happen to blow past.

That said, don't forget that if you're going to go through all the work of setting up a good paint environment that you'll need a decent quality filter / dryer on your air setup - the old beast of a compressor might leave oil in the air and I imagine your humidity is probably like ours (high, and miserable in the summer, lol) so there's a chance of water accumulation in the tank - both will impact your paint quality if they get pushed through the gun.

Of course, goes without saying, airflow and filters or not, please get the proper organic vapour P100 cartridge half-mask. 👍

-- Adam
Thanks for all the awesome info! I did order a water/oil separator from Crappy Tire. It's not expensive so I hope it's up for the task. I'm also planning on getting one of those water traps that attaches directly to the gun. Yesterday, I placed a small order on Amazon, including a cheapie HVLP gun (as a backup and maybe for my primer), a 6000 series respirator with NIOSH cartridges (I now have 3 functional masks, though at least one probably has the filters at the end of their life).

My biggest concern is that my ventilation system will not work as planned; that I won't be able to get enough air flow. I want a negative pressure set up for quick evacuation but didn't want to spend a small fortune on expensive 'explosion proof' exhaust fans.
atomic_hojiKincardine, ON, Canada · May 28, 2018#12
The little blue Campbell Hausfeld that I picked up at Canadian Tire or Princess Auto (can't remember which it was..) has worked well for me so far - though I've never test the air quality coming out of it either, and the small bit of paint I've done I haven't inspected closely; and probably shouldn't be.. lol. The sample cards and panel that I did with my Canadian Tire HVLP, a basic compressor with separator, and an economy line, single part straight colour paint (no metallic, pearl, etc..) gave a nice, even colour and decent gloss. I figure if I ever get the body on that truck straight, assembled, and ready for paint then it'll do just fine. That's is a lot of IFs ... 😆

I guess the old adage of what you want as a result vs what you want to spend applies - given the work you did on the low lip, I bet if you do a few practice boards and use some care you can probably put down a decent paint job that you'll be happy with; maybe at close inspection there are small imperfections, but hey at 50' it looks great! 😁 If you want the absolute perfect candy apple show car paint, well garage brew maybe won't work for ya.. lol

Glad to hear you've got the respiratory gear covered. A half-mask I assume? Only trouble I've had with half-mask is blow back (painting and cleaning in parts washer) into the face can irritate your eyes - safety glasses tend to fog up with the half-masks that I've used. Maybe just something to keep in mind if you spray into a fender well or other nooks and crannies..

I've worked with fans running when I've painted (spray, roller with a 2-part epoxy primer) or when using the parts washer full of varsol, thinner, diesel, etc..) and not had a problem - not that I want to say that and have you blow-up, I'd feel terrible, but while the products may be flammable the explosion limits might be higher you'll encounter painting - a good read of the MSDS and talk with the paint supply place should give you a better idea.

Can't wait to see how you make out! 👍

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · May 28, 2018#13
A few more pics...

Door to booth is the second panel of filters

Picture not included in this copy

Picture not included in this copy

I decided to bring the booth right out to couple with the door. I was worried about vapours backdrafting into the garage. I'm seriously reconsidering the use of box fans for a couple of reasons: 1) I doubt they will remove enough air and 2) I worry about the open motor even though being an induction motor it's not likely to emit sparks.

Picture not included in this copy
ern-dizCA all day · May 29, 2018#14
This is so cool.
DarkShadowFoxMassachusetts · May 29, 2018#15
oh awesome when get some freeup time can i borrow your booth.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 29, 2018#16
Originally Posted by atomic_hoji ↑
The little blue Campbell Hausfeld that I picked up at Canadian Tire or Princess Auto (can't remember which it was..) has worked well for me so far - though I've never test the air quality coming out of it either, and the small bit of paint I've done I haven't inspected closely; and probably shouldn't be.. lol. The sample cards and panel that I did with my Canadian Tire HVLP, a basic compressor with separator, and an economy line, single part straight colour paint (no metallic, pearl, etc..) gave a nice, even colour and decent gloss. I figure if I ever get the body on that truck straight, assembled, and ready for paint then it'll do just fine. That's is a lot of IFs ... 😆

I guess the old adage of what you want as a result vs what you want to spend applies - given the work you did on the low lip, I bet if you do a few practice boards and use some care you can probably put down a decent paint job that you'll be happy with; maybe at close inspection there are small imperfections, but hey at 50' it looks great! 😁 If you want the absolute perfect candy apple show car paint, well garage brew maybe won't work for ya.. lol

Glad to hear you've got the respiratory gear covered. A half-mask I assume? Only trouble I've had with half-mask is blow back (painting and cleaning in parts washer) into the face can irritate your eyes - safety glasses tend to fog up with the half-masks that I've used. Maybe just something to keep in mind if you spray into a fender well or other nooks and crannies..

I've worked with fans running when I've painted (spray, roller with a 2-part epoxy primer) or when using the parts washer full of varsol, thinner, diesel, etc..) and not had a problem - not that I want to say that and have you blow-up, I'd feel terrible, but while the products may be flammable the explosion limits might be higher you'll encounter painting - a good read of the MSDS and talk with the paint supply place should give you a better idea.

Can't wait to see how you make out! 👍

-- Adam
I don't know how I missed this but will read in its entirety and respond this evening. Thanks

Indeed, I'm not expecting perfection. I'm simply too impatient for that. So long as I have even color, good gloss and no visible dings, I can live with some paint imperfections.

Glad to hear you've had success with the fans and the various solvents you've sprayed. As young adults, we used to spray (sometimes with cans, other times with a compressor) all the time in garages without any mask, ventilation and with wood stoves cooking away. I guess one's sense of mortality creeps up with increasing age.

I have a couple 1/2 masks and another on the way.I just ordered a 6000 series reuseable 3M one and a set of NIOSH filters and pre-filters. One 3M is a disposable type that's only been used for about an hour. I never really thought about the blowback of paint/overspray. To keep 'in budget', I'll maybe try some kind of goggle as opposed to shelling out for a full face mask. I do have a painter's suit.
bairjoMay 29, 2018#17
I made a paint booth years ago. I used pvc pipe and fittings so it was easy to store when i was done. Used rolled painters plastic on all sides. I didn't put water on the floor for humidity. I didn't it was a good idea at all since that can affect the paint so i rolled plastic on the floor and drove the car in. Used a box fan to pull air out with a filter on an inlet window and a filter on the outlet. Worked out rather well for what i needed.
atomic_hojiKincardine, ON, Canada · May 29, 2018#18
Originally Posted by 06YarisRS ↑
...
Glad to hear you've had success with the fans and the various solvents you've sprayed. As young adults, we used to spray (sometimes with cans, other times with a compressor) all the time in garages without any mask, ventilation and with wood stoves cooking away. I guess one's sense of mortality creeps up with increasing age.
...
I've found the amount of really stupid s* that I've done through life has gone down dramatically now that I have kids.. Age and responsibility just ruining all the good fun, 'eh? 😆

I've tried both regular safety glasses and the foam padded goggle type but both fogged up on me and I ended up taking them off - hence how I found out the hard way about eye irritants.. lol. Anti-fog spray might help a bit too. I'd guess that doing the long, smooth body panels you'll be ok in that regard - just be cautious doing up under fenders or under the spoiler, etc..

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · May 29, 2018#19
Originally Posted by DarkShadowFox ↑
oh awesome when get some freeup time can i borrow your booth.
Of course! 👍
06YarisRSThread starterFredericton, New Brunswick, Canada · May 29, 2018#20
Originally Posted by ern-diz ↑
This is so cool.
Haha, I think so too. Should be fun!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 29, 2018#21
Originally Posted by bairjo ↑
I made a paint booth years ago. I used pvc pipe and fittings so it was easy to store when i was done. Used rolled painters plastic on all sides. I didn't put water on the floor for humidity. I didn't it was a good idea at all since that can affect the paint so i rolled plastic on the floor and drove the car in. Used a box fan to pull air out with a filter on an inlet window and a filter on the outlet. Worked out rather well for what i needed.
Did you use a typical home box fan? I just pulled the trigger on a 24" high speed fan on eBay as I was getting sceptical about the box fans' ability to remove enough vapour. I got it for $65.00 USD and it's 1/3 HP compared to the what 1/25 HP of the box fans? Maybe the box fans would have been fine, but for an extra ~ $20.00 I feel more confident with the 24" high speed.

Here is the fan I bought... It's still not an enclosed motor, but I've got yards and yards of fiberglass furnace hammock filter so I'll rig up some kind of loose fitting 'hat-like' cover for the motor to at least keep the overspray from mucking up the motor internals. The hammock filter breathes quite well, so I'm hoping it won't heat the motor up.

https://www.globalindustrial.ca/p/hv...-high-velocity


Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 29, 2018#22
Originally Posted by atomic_hoji ↑
I've found the amount of really stupid s* that I've done through life has gone down dramatically now that I have kids.. Age and responsibility just ruining all the good fun, 'eh? 😆

I've tried both regular safety glasses and the foam padded goggle type but both fogged up on me and I ended up taking them off - hence how I found out the hard way about eye irritants.. lol. Anti-fog spray might help a bit too. I'd guess that doing the long, smooth body panels you'll be ok in that regard - just be cautious doing up under fenders or under the spoiler, etc..

-- Adam
Haha, stupid stuff, don't get me started, LOL! I do appreciate the advice and I'm sure you're right that most any goggle will fog, especially when one is nervous and sweating. LOL! I'll make a point of being careful and paying very close attention to those potential trouble spots, for sure. 👍
ezhacker1San Francisco · May 30, 2018#23
https://jet.com/product/Lasko-Max-Pe...rigination=PLP

I got this to do future paint booth. also doubles for a good work fan when im doing stuff outside. I like that its sill portable but the selling point was i can angle it however i want (good for summer days toiling outside). The smaller air mover we used on our paint canopy didnt do as much air flow so i just made a large cardboard board into a filter box cut a rectangle for the blower to fit the box. So it was blowing fumes into the box, not sucking fumes into a box , if that makes sense. It definitely did the job well, kept the paint dust overspray that lingers in air to a minimum. Ill find a picture of how fast it clogs the filter.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 30, 2018#24
Originally Posted by ezhacker1 ↑
https://jet.com/product/Lasko-Max-Pe...rigination=PLP

I got this to do future paint booth. also doubles for a good work fan when im doing stuff outside. I like that its sill portable but the selling point was i can angle it however i want (good for summer days toiling outside). The smaller air mover we used on our paint canopy didnt do as much air flow so i just made a large cardboard board into a filter box cut a rectangle for the blower to fit the box. So it was blowing fumes into the box, not sucking fumes into a box , if that makes sense. It definitely did the job well, kept the paint dust overspray that lingers in air to a minimum. Ill find a picture of how fast it clogs the filter.
That does look like a very nice and practical fan. Are you planning to make a full size (big enough for a car) booth?
06YarisRSThread starterFredericton, New Brunswick, Canada · May 30, 2018#25
Installed my water separator...

My other gun and respirator arrived today to my US mailbox. Will pick them up this weekend.

Picture not included in this copy
ezhacker1San Francisco · May 31, 2018#26
It was a usual 10x10 canopy. Got most of the car in lol.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 31, 2018#27
Originally Posted by ezhacker1 ↑
It was a usual 10x10 canopy. Got most of the car in lol.
You got it all painted in the end, right? Job done!

I stumbled across another Amazon error...I think. I found a $70.00 18 mm paint gun for $18.09. I grabbed it and immediately after, the price went back to $70.00. I wanted an 18 mm for my primer anyway. Now I have 3 guns. I hope to god, I can at least paint with at least a tiny bit of skill, LOL.


I once bought a new Dorman transmission pan with plug - a nice heavy steel one - for my old Dodge Grand Caravan for $5.00. It was clearly a mistake as it too shot up to the regular price immediately thereafter. Amazon Victory! Love 'em!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 1, 2018#28
My neighbour told me of a guy about a kilometer from me that had some fluorescent lights he wasn't using. And how... The guy has about 20 48" 4 bulb T8 fixtures complete with bulbs from a demo. When I asked him how much he wanted for each, he said, "How does $5.00 each sound"? 👏 I bought 4 and he says if I need more to drop by. This guy has an amazing yard full of everything you can imagine. He also has a 24" industrial belt driven fan. It needs a motor but he's willing to part with it for basically change. It's probably a $1500.00 fan when equipped with a motor.

I plan to install my lighting (outside of the booth) tomorrow.

Picture not included in this copy
DarkShadowFoxMassachusetts · Jun 2, 2018#29
Originally Posted by 06YarisRS ↑
Of course! 👍
yaaay now to get to new brunswick. :X which side of canada is that on im bad with my provinces
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 2, 2018#30
Originally Posted by DarkShadowFox ↑
yaaay now to get to new brunswick. :X which side of canada is that on im bad with my provinces
Same side as you man. I think Boston is about 6 - 7 hours to where we live.
WeeYariGeorgetown, Ontario, Canada · Jun 2, 2018#31
Originally Posted by DarkShadowFox ↑
which side of canada is that on im bad with my provinces
...and even worse at pulling up a map ;)

BTW, it looks like no trip to NB for me this year. :(
Will only be the 3rd out of 29 years not making the summer vacation trip to see the in-laws.



Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 2, 2018#32
Originally Posted by WeeYari ↑
...and even worse at pulling up a map ;)

BTW, it looks like no trip to NB for me this year. :(
Will only be the 3rd out of 29 years not making the summer vacation trip to see the in-laws.



Sent from my Elite_5_5_Octa using Tapatalk
That's too bad WeeYari. There's always next year, and the year after and... 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 2, 2018#33
Got the lights up today and man, she's bright. I don't think I'll need any more. The wiring needs a little tidying up - a few wire staples here and there. I pieced the wiring together from ends I had lying around. A bit of overkill with 12/2 supplying the lights when 18 gauge would have been fine.

I built frames suspended from the ceiling so that the lights could be out of the booth. The ones mounted directly to the garage wall will be covered with the poly, Or -I haven't decided - I might build another wall and not use the actual garage wall at all.

Please excuse the mess.

Picture not included in this copy

Picture not included in this copy
DarkShadowFoxMassachusetts · Jun 3, 2018#34
Originally Posted by 06YarisRS ↑
Same side as you man. I think Boston is about 6 - 7 hours to where we live.
time to breakout my passport.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 3, 2018#35
I will need about another 100 square feet of poly. I sllghtly underestimated.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 3, 2018#36
Originally Posted by DarkShadowFox ↑
time to breakout my passport.
Dang right. After all this work, It would be sad to only paint one car in there. I do actually have a door ding to fix on my '08, so that will probably make an appearance in the booth too at some point.
RunethecursedSocal · Jun 3, 2018#37
maybe I should send some parts over to get painted such as side skirts, spoiler and lip...
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 3, 2018#38
Originally Posted by Runethecursed ↑
maybe I should send some parts over to get painted such as side skirts, spoiler and lip...
Haha, you might want to see my work first. LOL! It may not be up to snuff.
ern-dizCA all day · Jun 4, 2018#39
Bad. Ass. 👍
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 4, 2018#40
Originally Posted by ern-diz ↑
Bad. Ass. 👍
Errr...Thanks? I have been called both "bad" and an "ass" before, never on a forum though. 🤷 😆 😆
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 4, 2018#41
Plan to do some testing tomorrow when the poly is done and it's sealed up. Not sure whether I should pick up 2 more box fans (Walmart has them on for ~$17.00 each), or incorporate my new 24" high speed drum fan. I can probably sell the new drum fan locally for $100.00 and get 2 more box fans and have some change left over. Surely that should move some air!

Anyway, the frame is built. It is light and slides into the garage door frame nice and tight. And, the door clears it so it can close behind it. I have not yet sealed the fan box but will do that after I decide on fan configuration.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
kimonaHuntington Bch, CA · Jun 4, 2018#42
Oh, that's coming along nicely.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 4, 2018#43
Originally Posted by kimona ↑
Oh, that's coming along nicely.
Yeah, it is. Thanks. Cant wait to test it with the fans. I'm a little afraid that the 24" fan will implode my booth. LOL! I do have quite a bit of square footage in intake filters. Looking at a small wind meter on eBay for ~$14.00. They say that a booth should have a minimum of 100 ft/minute air flow. My main goal is to get adequate air flow to keep the 'combustibles' in a lean state. 👍 I'm probably overthinking this, but, again, my sense of mortality gets stronger with each passing year. 😆
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 5, 2018#44
I plan to rebuild my fan bank tomorrow to add in the new 24" fan after taking it out of its 'trolley'.

This fan is incredibly powerful. Even with the booth still unsealed, it really moves a lot of air in the right direction. The 2 box fans may not even be necessary. However, as my biggest fear is inadequate ventilation, I think I should be able to rest a little easier now. All fans will at least have their motor areas covered with filter material. I have lots and expect I'll need to replace it regularly throughout the job.

I'll report on the effectiveness of the ventilation 'system' after everything is buttoned up.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 7, 2018#45
My little guy was very helpful, holding the fan frame while I tucked and stapled the plastic under it. Then we double sealed it with Tuck Tape.

I am going to install another fan I have up top in the center of the garage door. The garage door will be open all the way and the whole area covered in plastic. It's a lot of fans but it's helping me feel more comfortable about keeping the solvents in the air well below LFL (Lower Flammability Limit). Probably over thinking this...

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 9, 2018#46
The work that I had done before resulted in several extra hours of grinding, sanding etc to remove it all. I am back to a solid base.

I wasn't happy with my tailgate from the first repair, so I've stripped it back and applied more body filler. The tailgate had some waves in it due to the collision before I bought it.

Picture not included in this copy

The car also had quite a few dings in the roof, hail I assume. I only found two small door dings. These are now fixed.

Picture not included in this copy

Picture not included in this copy


The car is about 80% sanded with 120 grit. I'm using a 5" random orbital sander.

Picture not included in this copy

Since my paint booth is done, I hope to apply the 2K high build primer this week.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2018#47
I have spent some time tweaking my booth. Yesterday, I installed a small paint station so that I don't have to risk further contaminating the booth by going in and out to mix paint, get supplies etc. I am picking up my 1.8 mm priming gun today.

Picture not included in this copy

I have significantly improved the airflow with the addition of another 3' x 3' filter. This is the cheap hammock filter, blue in color, to the left in the pic. This has made a huge difference in airflow. The crossflow is quite good and in 'testing' the overspray in the air is pulled fairly quicky down and out. Final tweaks will occur with the car actually in the booth. On the right, I set up a temporary spray board to check spray pattern.

Picture not included in this copy

I still have to route the fan power cords out of the booth so as to have no electrical connections inside the spray area.

One thing I like about having the fans low is that apparently solvent vapours settle to the ground as they are heavier than air. The fans pull quite nicely across the floor and should clear out vapours under the car.

Picture not included in this copy

My primer arrives today. I still have to finish taping, sanding, multiple washes, and degreasing before spraying the primer. I bought Evercoat Feather Fill G2 polyester high build primer so I can block sand before painting. I may actually spray the primer outside on a calm day, sand and then bring the car into the booth for the base coat and clear coat.
kimonaHuntington Bch, CA · Jun 17, 2018#48
Man, you've been busy!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2018#49
Originally Posted by kimona ↑
Man, you've been busy!
Yeah, a bit silly, eh? I've been wanting to learn to paint for a while now, so I don't mind the effort. If I'm successful at putting paint on decently, I hope to find a couple more small cars to paint and charge a small fee. That way I can recoup some of my costs. I should still be well under $1K for my paint job, everything included.