06YarisRSOriginal postFredericton, New Brunswick, Canada · Sep 5, 2017#1Picked up this great little car for $2200.00 Canadian. It has 174000 km on the odometer and it's in great shape. It came with 4 new Michelin Defender tires - about a month old. I've ordered a used exhaust manifold from eBay for $45.00 and bits and pieces (gasket, donut, spring bolt kit etc). The manifold flange ears are gone, as in not even there anymore. The car's body is in fantastic shape for an older car driven in the salt and slush. The underbody, rocker panels, doglegs etc are all excellent. I hope to keep it this way and I have gallons of old ATF for interior panels, Fluid Film underneath.
A few jobs I'm working on:
This job is done. Driver's rear wheel well (so glad that the previous owner at least put some paint over the ding:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This is a WIP. Hatch: This took a lot of work behind straigtening out and reinforcing. The outer skin had detached from the inner frame at this corner:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This job is a WIP. Thresholds (various pics from both sides)
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This job is done. Headlight restoration. These lights were both very oxidized and quite yellow. I wet sanded and polished. No clearcoat. I use my Klasse High Gloss Paint Sealant.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The hatch lock did not work. Thanks to this forum, I found a thread on disassembling it and cleaning. Also, the nylon tab that swings the latch back was broken off. Fortunately, it was in the bottom of the hatch. A little hot glue fixed that. I wasn't looking forward to buying a latch assembly, so was really glad to see that it was repairable.
Picture not included in this copy
Since I love Rock Auto, I've ordered rear brake drums (these are a bit rusty), a hardware kit and shoes. Also, ordered 6L ATF, a transmission filter, 4 oil filters, 4 Denso Iridium plugs, and a couple air filters.
Replies 83
ern-dizCA all day · Sep 6, 2017#2You hit the ground running with this one!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 6, 2017#3 Originally Posted by
ern-diz ↑ You hit the ground running with this one!
Thanks. Well, it's such a great little car and there was a lot to work with. I took it to a body shop today; the same one I went to before I did the body work. I was quoted ~$600.00 - $700.00 to do the 2 areas initially. With the body work done now, the shop will charge me around $300.00 to paint it. I'm not fully satisfied with the job the rattle cans did (or the job "I" did with the rattle cans, lol). It looks OK, but the rest of the car is in such good shape, the 300 is worth it IMO. I set myself a budget of $1500 ($1800 at the outside) for repair work. So far I'm only in for about $250.00. I have a battery light flickering and have read that the connector or the voltage regulator are possible causes. If the connector isn't the issue, I may grab a reman alternator and pop that on. The seller said the light had been on for 3 years with no issues. Voltmeter says the alternator is producing 14V at idle and no starting issues at all - lots of crank power, but the DRLs are out and I read that may be related to the voltage regulator.
WeeYariGeorgetown, Ontario, Canada · Sep 6, 2017#4Yeah, the DRLs will be dead with the regulator acting up. My battery light intermittently flickered for several years before eventually staying lit solid.
Sent from my Elite_5_5_Octa using Tapatalk
kimonaHuntington Bch, CA · Sep 6, 2017#5It's coming along nicely! Looking forward to more photos as you get it all sorted out.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 6, 2017#6 Originally Posted by
WeeYari ↑ Yeah, the DRLs will be dead with the regulator acting up. My battery light intermittently flickered for several years before eventually staying lit solid.
Sent from my Elite_5_5_Octa using Tapatalk
Thanks! Great to know. Rather than take the alternator apart to install a new regulator, I think I'll just got for a whole reman..
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 6, 2017#7 Originally Posted by
kimona ↑ It's coming along nicely! Looking forward to more photos as you get it all sorted out.
Thanks Kimona! I'll be sure to post more.
hairygityetiUnited Kingdom · Sep 6, 2017#8Gonna look nice!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 6, 2017#9 Originally Posted by
hairygityeti ↑ Gonna look nice!
Thanks! I hope so. I got lucky as silver is my fav color choice in automobiles. :)
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 7, 2017#10 Originally Posted by Bart68 ↑
I had a 06 Corolla that did that with the battery light and I was talking with a
good friend of mine that told me to whack the alternator while the car is
running, he said the brushes probably just have crud on them. So I took my
tire iron and with the car running gave it a few good whacks, the light never
came back on and I drove that car for another 200,000 with no more issues.
Not sure if that will fix your problem or not but it an easy cheap fix if it does.
Well there you go. I just picked up a reman unit this morning. It's still in the box, so I'll try tapping it first. Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 8, 2017#11I replaced the alternator and the battery light is gone. Yay!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2017#12Final priming is done. Just a light sand with 320 and then the base and clear. Hoping to be done today.
Picture not included in this copy
Picture not included in this copy
WeeYariGeorgetown, Ontario, Canada · Sep 9, 2017#13Where in NB are you? I spend two weeks every year in Greater Moncton visiting in-laws.
Sent from my Elite_5_5_Octa using Tapatalk
WeeYariGeorgetown, Ontario, Canada · Sep 9, 2017#14I'm hoping I nipped my door sills in the bud. Since the plastic trim wears through the paint, I cleaned up my early development of rust and sprayed several coats of bed liner along the area where that trim makes contact.
Sent from my Elite_5_5_Octa using Tapatalk
kimonaHuntington Bch, CA · Sep 9, 2017#15 Originally Posted by
06YarisRS ↑ Final priming is done. Just a light sand with 320 and then the base and clear. Hoping to be done today.
Looking good. You're moving quickly.
I guess I would have removed the rear mud flaps rather than taping them.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2017#16 Originally Posted by
WeeYari ↑ Where in NB are you? I spend two weeks every year in Greater Moncton visiting in-laws.
Sent from my Elite_5_5_Octa using Tapatalk
Hey WeeYari.
We live in Beaver Harbour, near St. George/Pennfield. Moncton is a regular visit for us in the summers. Kids love it! I was in Moncton about 3 weeks ago test driving small cars.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2017#17 Originally Posted by
WeeYari ↑ I'm hoping I nipped my door sills in the bud. Since the plastic trim wears through the paint, I cleaned up my early development of rust and sprayed several coats of bed liner along the area where that trim makes contact.
Sent from my Elite_5_5_Octa using Tapatalk
I know what you mean about the trim scraping the paint off. I think it's just shallow surface rust but unsightly none-the-less. I usually put some 3M film under the trim after I restore them, as well as wrap it around the wear points of the door threshold. Puts an end to scratches/scraping. It's the best cheap fix I know of.
Also, I picked up another 1/2" high speed steel countersink bit and I already have a box of 100 body plugs. Yesterday I drilled a hole in the top of the rocker - about midway on the threshold. I hit another steel plate just 1/4" below. However, my goal was achieved when I dumped about 1/2 L of used atf in there with my transmission funnel and it ran out along the pinch seam of the rockers and into my waiting container. I use a piece of old eavestrough to collect and 'recycle' my atf rustproofing. :)
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 9, 2017#18 Originally Posted by
kimona ↑ Looking good. You're moving quickly.
I guess I would have removed the rear mud flaps rather than taping them.
Yeah, it's coming along. Haha, yes, removing them would have been more wise for sure. I just didn't want to take the wheel off to get to the screws. I suppose I could have used a stubby screwdriver. Incidentally, I did later remove the wheels to check the condition of the rear brakes. My pedal is a tad soft and I thought I'd poke around in there and play with the adjusted a bit. I did tighten them up a bit but still have a bit of pedal softness. I have to say that this car is indeed the easiest car I have worked on. Well designed and intuitive. Removing the drums was a joke with a couple 8Mx1.25 bolts.
The pads are a bit worn, but since this thing is so easy to work on, it should be a snap to install my new brake parts.
I'm thinking I might bleed the brakes soon and see if that stiffens up the pedal. I haven't owned a drum brake equipped car in eons. Will have to research how to bleed the system. Calipers are easy with the bleeder screws. During my quick inspection I didn't see such an item on the wheel cylinder. I also adjusted my handbrake and that, at first, seemed to help, but after a short drive it was a bit soft again.
Enough rambling... 😆
WeeYariGeorgetown, Ontario, Canada · Sep 10, 2017#19 Originally Posted by
06YarisRS ↑ We live in Beaver Harbour, near St. George/Pennfield.
Beautiful country. Been a lifer there?
Sent from my Elite_5_5_Octa using Tapatalk
hairygityetiUnited Kingdom · Sep 10, 2017#20Looking good m8 cant wait to see finished product
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2017#21 Originally Posted by
WeeYari ↑ Beautiful country. Been a lifer there?
Sent from my Elite_5_5_Octa using Tapatalk
Yes, we love it. My wife and I are originally from Fredericton. About a dozen years ago I took a teaching position on Grand Manan; I'd been in Manitoba teaching for the decade prior to that. I then requested and received a transfer off the island. We lived in Back Bay for 2 years, then finally Beaver Harbour. I've always loved this area for it rugged coastlines and ocean views. We lucked out and picked up a great property on the water. Our kids are both born Charlotte County'ers'.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 11, 2017#22 Originally Posted by
hairygityeti ↑ Looking good m8 cant wait to see finished product
Thanks hairygityeti! Can't say I'm completely happy with the finished product. I'm no body man, that's for sure. I got a little overzealous on the final coats of base coat and got some more concentrated areas of metalic flake (too close with the can in a few spots. Also, there are a couple of areas on the liftgate that had minor bumps that weren't visible until the final clearcoat was applied. I may wait a week or two and resand, fix the small bumps and repaint. Overall, it looks pretty good though. The bumper hasn't been wet sanded and polished yet, so it's a bit flat looking. Plus, have some overspray to contend with.
I'll take a couple more pics in better lighting later.
Picture not included in this copy Ain't the little Yaris, cute? Haha
Picture not included in this copy Over the winter, I am going to restore the wheels. They are in very good shape but a few scratches. here and there.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 13, 2017#23I have finished the painted and clear coated sills by applying Trimbrite heavy paint protection film. This stuff goes on great with a heat gun and quite easily wraps around the contours.
I drilled a couple more holes in the c-pillars and 'injected' a bunch of Rust Check red. Then I dumped about a half liter of ATF in with my trans funnel. After a few seconds it started to drip out into my pans. My rockers (front to back), wheelhouses and interior wheel well seams should now be thoroughly soaked with ATF/Rust Check.
Rocker panels:
Picture not included in this copy
Rear quarter panels and dogleg area:
Picture not included in this copy
I also started the cleaning process. This car was filthy. The seats produced a of couple gallons of very dirty brown water in my shopvac. I will tackle the back tomorrow.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 17, 2017#24I shopped around on eBay and picked up floor liners, buying the fronts and rear from different sellers. Total was around $100.00 USD. I would have preferred black but the grey ones were quite a bit cheaper (Gotta stay within budget, you know, haha). If I'd gone with tan, I would have saved more, tan, nah.
These are Aries StyleGuard and seem really well made. They WILL NOT MOVE once positioned. In fact, they are really hard to position initially because if they contact and carpet at all, it's like they are glued down. The fit is as good as weathertech IMO.
Picture not included in this copy
I see that I am going to have to do another round of upholstry extracting. These seats were really dirty and this is after one intense cleaning.
Picture not included in this copy
Picture not included in this copy
Also, picked up a cheap arm rest/console for $32.00 USD
Picture not included in this copy
Finally, a smartphone adapter for the stock radio
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 17, 2017#25After breaking a bleeder screw off attempting to flush brakes, I thought that rather than sink into depression, I'd do something non labour intensive - and most of all, safe for our little Yaris. 🙂 I'll pick up a wheel cylinder - probably 2 tomorrow, if available locally.
Procedure:
- brake cleaner and towel off
- wire brush
- painted on phosphoric acid and let sit 30 minutes
- Washed off and brake cleaner again
- 3 coats Ace Hardware heat resistant BBQ paint
I've used this paint for a few years now and providing that a proper prep job is done, it will stand up really well. At wheel change time, I'll give them a quick once over with the wire brush, brake cleaner and respray them. Often they just need a cleaning to get rid of the brake dust and they're nice and clean again.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
kimonaHuntington Bch, CA · Sep 17, 2017#26Your car is really coming along nicely and looking great.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 17, 2017#27 Originally Posted by
kimona ↑ Your car is really coming along nicely and looking great.
Thanks Kimona! I'm sure having fun with it. Well, except the broken bleeder screw. I'll try to source a pair of wheel cylinders locally. Failing that, the poor old Yaris will be driveway-bound for another week, sadly.
ern-dizCA all day · Sep 18, 2017#28 Originally Posted by
kimona ↑ Your car is really coming along nicely and looking great.
+1
I am, however, confused about the mats. Aries StyleGuard? They look exactly like my 3D Maxpider Kagu mats. In fact, I can see part of the 3D logo in the pic of the passenger side. Thought maybe it was a reference to the material used, or something like that, so I pulled up the ad for them and didn't see any mention of 'Aries StyleGuard' 🤷
In any case, they are fantastic, and again, the car is really coming along nicely.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 18, 2017#29 Originally Posted by
ern-diz ↑ +1
I am, however, confused about the mats. Aries StyleGuard? They look exactly like my 3D Maxpider Kagu mats. In fact, I can see part of the 3D logo in the pic of the passenger side. Thought maybe it was a reference to the material used, or something like that, so I pulled up the ad for them and didn't see any mention of 'Aries StyleGuard' 🤷
In any case, they are fantastic, and again, the car is really coming along nicely.
Thanks. I'm enjoying working on the car. I replaced my passenger side wheel cylinder today and bled the line. It was a very easy job, thankfully.
I think that maybe the floor liners are distributed through a couple of brand names. Here's a pic of the logo on my mats:
Picture not included in this copy ern-dizCA all day · Sep 18, 2017#30Ah, how interesting. Same 3D logo, but mine don't have the Aries marking. I wonder what the difference, if any, there is between the Maxpider Kagu and Aries series? From the pics, they look identical. You might be right, it could just be a branding change.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 18, 2017#31 Originally Posted by
ern-diz ↑ Ah, how interesting. Same 3D logo, but mine don't have the Aries marking. I wonder what the difference, if any, there is between the Maxpider Kagu and Aries series? From the pics, they look identical. You might be right, it could just be a branding change.
It would seem so. I'm liking them quite a bit. We shall see how well they clean up and how long they last/how durable the top layer is. I like the WeatherTechs, but they do get scratched up pretty badly after a few years use.
As an aside, I got the other wheel cylinder installed and bled that station. Now all I have to contend with are the bleeder screws on the calipers. I haven't even tried them but I do have a can of ReleaseAll, I think it's called. I'm pretty sure it helped free up the brake fasteners.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 23, 2017#32 Originally Posted by
ern-diz ↑ Ah, how interesting. Same 3D logo, but mine don't have the Aries marking. I wonder what the difference, if any, there is between the Maxpider Kagu and Aries series? From the pics, they look identical. You might be right, it could just be a branding change.
Well, I'm not super impressed with these mats. My kids somehow seem to be little gravel magnets and bring them in on their shoes. The back mat already has a few unremoveable scratches. My van liners on the other hand - subject to the same gravel assault, and equipped with WeatherTechs - are in prefect shape despite being much older. The Aries ones look great, but I'm having doubts about their durability. Frankly, I'm wishing I'd shelled out more bucks and got the weatherTechs.
hairygityetiUnited Kingdom · Sep 24, 2017#33She is looking excellent i am jealous mines an old series 1 but she is a good work horse!. I live near the North sea so cars here tend to rust badly so im jealous and love what you have achieved,dont put yourself down spraying with cans is not easy for many at least you avoided runs and sags 👏 i am thinking of under sealing mine to slow down the rust she is 18 years old,keep up the good work
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 24, 2017#34 Originally Posted by
hairygityeti ↑ She is looking excellent i am jealous mines an old series 1 but she is a good work horse!. I live near the North sea so cars here tend to rust badly so im jealous and love what you have achieved,dont put yourself down spraying with cans is not easy for many at least you avoided runs and sags 👏 i am thinking of under sealing mine to slow down the rust she is 18 years old,keep up the good work
Thanks a lot hairygetyeti! I love the series one. My wife had an Echo and despite being completely neglected (this was before we met, of course 😉 ) it lasted for years and years and had close to 300000 km on it. After we got together, we kept the car for a couple of years. I did a quick fiberglass and bondo rear rocker panel repair on the Echo before selling it. I could push my finger through the dogleg area and it was basically the paint and primer that was holding everything together. When I sold it, I told the buyer that I'd drenched it on the inside with motor oil. I advised that he do that at least annually. Other than that rust, the underbody of her echo was in excellent shape. We too live by the ocean but it's more the tons of road salt they lay down that gets to our cars. I really wish they would find an alternative, less corrosive de-icer.
Can you get access to Fluid Film near you? It's a bit costly unless you buy by the gallon and use a sprayer and compressor. I have purchased FF when on sale in the 11oz spray cans and I bet you could do a Yaris completely with about 3 cans. I've also bought the gallon (went halves with our old principal), heated it up and sprayed 4 -5 cars.
hairygityetiUnited Kingdom · Sep 24, 2017#35 Originally Posted by
06YarisRS ↑ Thanks a lot hairygetyeti! I love the series one. My wife had an Echo and despite being completely neglected (this was before we met, of course 😉 ) it lasted for years and years and had close to 300000 km on it. After we got together, we kept the car for a couple of years. I did a quick fiberglass and bondo rear rocker panel repair on the Echo before selling it. I could push my finger through the dogleg area and it was basically the paint and primer that was holding everything together. When I sold it, I told the buyer that I'd drenched it on the inside with motor oil. I advised that he do that at least annually. Other than that rust, the underbody of her echo was in excellent shape. We too live by the ocean but it's more the tons of road salt they lay down that gets to our cars. I really wish they would find an alternative, less corrosive de-icer.
Can you get access to Fluid Film near you? It's a bit costly unless you buy by the gallon and use a sprayer and compressor. I have purchased FF when on sale in the 11oz spray cans and I bet you could do a Yaris completely with about 3 cans. I've also bought the gallon (went halves with our old principal), heated it up and sprayed 4 -5 cars.
Its prity bad corrosion under her rear but no holes i will probs use a can off black under seal and cover her ass, with my car its just delaying the inevitable shes had one new wing and new door sill so she still solid although i might paint the petrol tank with fibre fill mixed with resin cos of slight leak on a full tank.As for the rock salt on the roads " ditto "Lets hope we have another mild winter😆
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 24, 2017#36Although my exhaust system is in decent shape - most of it - I decided to paint it with VHT Flameproof paint. I used this on my old Dodge Grand Caravan and it stuck like glue. It stayed on there for years and any other high heat paint I'd put over it bubbled off leaving the Flameproof fully intact.
Process:
First I wire brushed everythng off, then sprayed it liberally with Rust Check Rust Converter. After that dried, I gave it a light sand and washed it off with brake cleaner. I applied 3 coats about 10 minutes apart. After about an hour, I did the first stage curing - about 15 minutes idling. half an hour later I went for a short drive. I could smell the stuff curing. In about 1/2 hour we're going out for a short drive for the final curing.
For anyone unfamiliar with the product, it s a ceramic based coating that can handle extreme heat. Of course, preparation is key. Here's hoping it stays around as well as it did on the van. It looks better and should provide a little protection to the outer surface this winter. I do have a small hole in the mid pipe which I patched with fiber resin tape. It's very solid and quiet. However, I will be replacing this section of pipe.
Pics:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Yes, I do have too much time on my hands.
Check out all the thick goopy undercoating. 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 24, 2017#37 Originally Posted by
hairygityeti ↑ Its prity bad corrosion under her rear but no holes i will probs use a can off black under seal and cover her ass, with my car its just delaying the inevitable shes had one new wing and new door sill so she still solid although i might paint the petrol tank with fibre fill mixed with resin cos of slight leak on a full tank.As for the rock salt on the roads " ditto "Lets hope we have another mild winter😆
Yes, salty water is the devil's brew. I am going to be putting bed liner in my driver's side rear wheel well after a good scraping, sanding and primimg. I already did the passenger side. The factory rubberized undercoating is pretty much beaten off but the wells are in great shape; mostly factory paint and a few small surface rust spots. Once the bedliner dries, I'll be soaking it with rustproofing as well as attacking it from behind with the rust proofing.
Best of luck with your repairs. Typically, these days, the body gives out long before the powertrain, especially with the high quality mechanics of these cars.
ern-dizCA all day · Sep 25, 2017#38 Originally Posted by
06YarisRS ↑ Well, I'm not super impressed with these mats. My kids somehow seem to be little gravel magnets and bring them in on their shoes. The back mat already has a few unremoveable scratches. My van liners on the other hand - subject to the same gravel assault, and equipped with WeatherTechs - are in prefect shape despite being much older. The Aries ones look great, but I'm having doubts about their durability. Frankly, I'm wishing I'd shelled out more bucks and got the weatherTechs.
Interesting. My back carpets are still in good shape, so I just bought the front two. Again, I'm not sure if there's a difference between the Aries model you got and what I have. The 3D Maxpider Kagu mats I got boast a triple layer design of non-stick on the bottom, padding in the center and then weather proof upper. So far, they're holding up great.
I would have liked to go with Weathertech because I really like the company (my window visors are Weathertech), but it wasn't a cost thing for me, it was a design thing. In your van, or in a truck, I'm sure they look great. In a small passenger car, not so much. Just my opinion, but I think they're too utilitarian looking. Something you'd put in a work truck. The 3D's are a lot nicer looking for a passenger car.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 25, 2017#39 Originally Posted by
ern-diz ↑ Interesting. My back carpets are still in good shape, so I just bought the front two. Again, I'm not sure if there's a difference between the Aries model you got and what I have. The 3D Maxpider Kagu mats I got boast a triple layer design of non-stick on the bottom, padding in the center and then weather proof upper. So far, they're holding up great.
I would have liked to go with Weathertech because I really like the company (my window visors are Weathertech), but it wasn't a cost thing for me, it was a design thing. In your van, or in a truck, I'm sure they look great. In a small passenger car, not so much. Just my opinion, but I think they're too utilitarian looking. Something you'd put in a work truck. The 3D's are a lot nicer looking for a passenger car.
I agree about the aesthetics. The mats we have do look great. I'll get over the scratches soon. Haha. After all, they are there mainly to protect the carpet. The WeatherTechs do have a bit of an 'industrial' look, definitely.
WeeYariGeorgetown, Ontario, Canada · Sep 25, 2017#40kimonaHuntington Bch, CA · Sep 25, 2017#41WeeYari, those are really nice mats! Is the carpet surface durable and easy to clean?
ern-dizCA all day · Sep 25, 2017#42 Originally Posted by
kimona ↑ WeeYari, those are really nice mats!
+1
WeeYariGeorgetown, Ontario, Canada · Sep 25, 2017#43 Originally Posted by
kimona ↑ Is the carpet surface durable and easy to clean?
Yes and very. You would never guess it to look at them now that they had weathered a salt laden winter.
Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 25, 2017#44 Originally Posted by
WeeYari ↑
Ooh...I do like those! I've never heard of them before.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2017#45I picked up my pipe, tint for the rear windows (35%) and rubber bumper protector.
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2017#46The tint was an abject failure. My fault for rushing the job.
The bumper protector looks pretty good and should never come off. I used a pile of 3M tape and heated it to ensure a good bond.
Exhaust pipe went on without too much incident. I am going to get it welded though as the flange lined up with a flattened spot on the stock pipe so seal with clamp isn't 100%. Some muffler cement filled the small gap temporarily.
Bumper protector and a bit of paint film on hatch edge:
Picture not included in this copy
Some paint film on bumper :
Picture not included in this copy
kimonaHuntington Bch, CA · Oct 4, 2017#47^^^ That should do the trick. Looks good.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2017#48 Originally Posted by
kimona ↑ ^^^ That should do the trick. Looks good.
Yup, should do. Can't complain for $8.00.
I kinda rushed the paint film and should have cut a smoother radius, but what the hey, you can barely see it anyway unless you're looking for it.
Thanks!
WeeYariGeorgetown, Ontario, Canada · Oct 4, 2017#49Where'd you get that exhaust pipe?
Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2017#50 Originally Posted by
WeeYari ↑ Where'd you get that exhaust pipe?
Sent from my Elite_5_5_Octa using Tapatalk
Rock Auto. Part 750-253. Here's a link:
http://www.rockauto.com/en/moreinfo....1738&jsn=10382 It's a great, and cheap, alternative to buying the whole cat pipe. It was like $55.00 CAD shipping included (to my US post box).
BTW, do you know if CTScott is still here and selling cruise control units? Thanks man! I sent you a PM. If you'd be so kind as to let me know if you receive it, I'd be very appreciative. Not sure my PMs are sending as there's nothing in my sent box.