So, that exhaust pipe deletes the muffler?
2006 YarisRS 'Renovations'
84 posts · 28,317 views · page 2 of 2
Replies continued
No. Look at it again and you will see the muffler connecting flange on the end of it. That piece he got replaces a portion of the pipe aft of the resonator.Originally Posted by ern-diz ↑So, that exhaust pipe deletes the muffler?
Sent from my Elite_5_5_Octa using Tapatalk
I see, thanks. At first glance, it looked like the end opposite of the side that connects to the resonator was an exhaust tip.Originally Posted by WeeYari ↑No. Look at it again and you will see the muffler connecting flange on the end of it. That piece he got replaces a portion of the pipe aft of the resonator.
Sent from my Elite_5_5_Octa using Tapatalk
I wish I'd seen this before I bought from Rock Auto. Since my exhaust guy deleted my resonator, I could have gotten this piece - including the resonator.
https://www.carid.com/2006-toyota-ya...-80703136.html
https://www.carid.com/2006-toyota-ya...-80703136.html
Finally got around to painting my spoiler. It is by no means a perfect job. I didn't fine sand it as much as I should have. It's got some fine sand marks and the clear coat needs to be sanded and polished.
Spoiler with adhesion promoter applied:
Picture not included in this copy
With tack coat:
Picture not included in this copy
With base coat:
Picture not included in this copy
Clear coat. Looks matte, but will be glossy after wet sanding and polishing:
Picture not included in this copy
Spoiler with adhesion promoter applied:
Picture not included in this copy
With tack coat:
Picture not included in this copy
With base coat:
Picture not included in this copy
Clear coat. Looks matte, but will be glossy after wet sanding and polishing:
Picture not included in this copy
That should make it look even better. You did a really good job with everything so far.
Thanks, Whiplash! It's coming along. Can wait to widen the rear track with the Penguin spacers I just picked up. Then, from an exterior point of view, it should be done. Oh, well, once the front lip is installed and painted too!Originally Posted by Whiplash ↑That should make it look even better. You did a really good job with everything so far.
Pics never show the flaws, but that looks real good.
Thanks. Well, it's going to get another sanding and repaint. I took it out into the sunlight and it looks ok, but I could also see a bit of light shining through. I have a pretty good basecoat though now. I'll post up pics of the finished product.Originally Posted by WeeYari ↑Pics never show the flaws, but that looks real good.
After that, it's the front lip. That, I'll install first and then paint it on the car. I doubt that this paint would handle any amount of flex.
The above said, if I'm not satisfied with the overall look of the car, I have another possible plan. There is a fellow locally with an autobody/collision shop. I am going to ask him to do an estimate on painting the back of the car. I've seen some of his blending work from all angles and the guy is a pro - virtually impossible to see his blending. The other option is a total repaint, except the door jambs, engine bay under hood, tailgate, inside of doors etc. I had spoken with him before and he quoted me around $350 - $400.00 to do the back end. If I repaired the tiny dings and sanded out the light scratches and he was willing to seal, base coat and clear for around $1K, I may do it. He is open to painting cars that other non-professionals have done minor body work on.
When you polished out the headlights, what grit of sand paper did you use?
Also, is the the exact polish you buffed them with afterwards?
https://www.autogeek.net/klashiggloss.html
Also, is the the exact polish you buffed them with afterwards?
https://www.autogeek.net/klashiggloss.html
If memory serves me correctly, I used 1500 followed by 2000 or 2500, wetsanding. That stage is important as the more time you put in here, the better the job, IMO. Keep sanding lightly until the yellow slurry turns to white slurry. Rinse well. I then used Meguiar's Ultimate Polish with my dual action polisher and cutting pad. After a good cleaning, rinse and microfiber towel drying, I applied a couple of coats of Klasse High Gloss Sealant Glaze as in your link - about a day between applications. This is because to get the yellow out, you have to sand off the clearcoat that is on the headlight. That's what yellows. The klasse serves as a replacement for the uv blocker in the clearcoat to keep them from yellowing again. All of this is just my theory, but I have had good long-term success with this approach. We did a raft of cars in our school shop and our 'customers' were thrilled with the results.Originally Posted by BennyLava ↑When you polished out the headlights, what grit of sand paper did you use?
Also, is the the exact polish you buffed them with afterwards?
https://www.autogeek.net/klashiggloss.html
Thinking about doing yours?
Klasse HGSG is the product I use exclusively for my car's paint. I have been using it for years and although I haven't tried many other sealants, it is amazingly durable/long-lasting and a few layers creates the most gloss candy-like and slick coating. And, to boot, a $30.00 jug (large jug) will last years! My cars get 4 - 5 coats a year and application is quick. If you want the best method, IMO, follow the link below. I do my headlights every time I do the paint too. I don't use Klasse All In One (AIO) as my paint is pretty clean usually anyway.
https://www.detailedimage.com/Ask-a-...de-and-review/
This look better? I think the extra effort will be worth it. I resanded, repainted and re-cleared. Clearcoat is nice and thick, so should be easy to polish out the orange peel and achieve a high gloss. 👍Originally Posted by WeeYari ↑Pics never show the flaws, but that looks real good.
Some day I'd like to invest in some actual automotive painting equipment and learn how to properly paint a car.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
For a DIY, I think it looks great.
Originally Posted by ern-diz ↑For a DIY, I think it looks great.
Thanks man! I'll give it a week or so and then wet sand and polish. Should be very smooth with good reflectivity.
I thought it looked good earlier. Any flaws then were really only visible to your eye. Camera doesn't pic them up. Just like taking a pic of my front bumper. Looks fantastic in pictures, naked eye sees something that looks to have seen the business end of a 12 gauge.Originally Posted by 06YarisRS ↑This look better?
Sent from my Elite_5_5_Octa using Tapatalk
So true. Once on the car and out of the garage, I'm sure all the imperfections will jump out. My whole car is a "looks great from 10 - 20 feet away" vehicle. LOL.Originally Posted by WeeYari ↑I thought it looked good earlier. Any flaws then were really only visible to your eye. Camera doesn't pic them up. Just like taking a pic of my front bumper. Looks fantastic in pictures, naked eye sees something that looks to have seen the business end of a 12 gauge.
Sent from my Elite_5_5_Octa using Tapatalk
Well, I got the job done. It took two attempts with the 3M tape. Got it on crooked the first time and it was a bear to remove. Second time was better. I was going to install just with the tape, but because I could not ascertain that the tape was in full contact with both the car and the spoiler, I decided to drill and use self-tapping screws as well. I then saturated the holes with thick rust proof compound.
I'm really on the fence about the look. It could go either way - the new spoiler or the stock stubby spoiler.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I'm really on the fence about the look. It could go either way - the new spoiler or the stock stubby spoiler.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
That looks great!
Thanks Cap'n! It looks pretty good from a few feet away. The spoiler was pretty rough and even though I sanded quite a bit, it's far from perfect.Originally Posted by Captain Yaris ↑That looks great!
Looks good to me. Love those factory alloys, too. I think this car would level up 100 cool points if you installed some lowering springs. It would make a huge impact.
Well, I dig it! Coincidently, do these spoilers do anything on our cars? Is there any downward force being exerted?
10 whp in cool factor. Maybe keep window glass a bit cleaner. Down force nil.Originally Posted by Captain Yaris ↑Coincidently, do these spoilers do anything on our cars? Is there any downward force being exerted?
Sent from my Elite_5_5_Octa using Tapatalk
If I remember correctly, our cars are governed by aerodynamics. Drag keeps them from going much over 115 mph. I think the added drag from the spoiler brings down the top speed lol. They do look cool, though.Originally Posted by Captain Yaris ↑Well, I dig it! Coincidently, do these spoilers do anything on our cars? Is there any downward force being exerted?
Oh, don't get me started. LOL! I agree. I confess as much as I like the look of the lowered Yari, I have not even glanced at pricing for a drop, or what's involved. I think my next move is a rear sway bar, so I'm keeping my eyes out for a used one before dropping a few hundred on a new one.Originally Posted by ern-diz ↑Looks good to me. Love those factory alloys, too. I think this car would level up 100 cool points if you installed some lowering springs. It would make a huge impact.
What all is involved in dropping the car?
I am seriously thinking about swapping out my new 195/60R15s that I just put on my '08 with the 185/6015 Michelin Defenders that are currently on my '06. If the 195s plus Penguin spacers will fit without rubbing on my '06, I think it would be a stellar look. If I did that I bet I'd be pushing it, especially if a drop becomes a factor.
Thanks! Not sure, but I do know that on my old Grand Caravan, the application of a rear spoiler kept the liftgate window a heck of a lot cleaner. LOL!Originally Posted by Captain Yaris ↑Well, I dig it! Coincidently, do these spoilers do anything on our cars? Is there any downward force being exerted?
No question! 👍Originally Posted by WeeYari ↑10 whp in cool factor.
My experience was spending roughly $200 on a set of springs and having a friend help me install them one sunny afternoon. There are cheaper spring options and good install walk-throughs here on the forum.Originally Posted by 06YarisRS ↑What all is involved in dropping the car?
Awesome. Thanks! I like the idea of a drop but I wouldn't want to go more than 1.5" max. We live in a rural area and I need clearance for the various rodents and other small critters that suicidely charge onto the road.Originally Posted by ern-diz ↑My experience was spending roughly $200 on a set of springs and having a friend help me install them one sunny afternoon. There are cheaper spring options and good install walk-throughs here on the forum.
On eBay springs range from ~$70.00 up to a few hundred. In the pricing middle are sets of Manzo springs. Know anything about them? I did read warnings about cheaper, so called "JDM" knockoffs, so would probably avoid those. Open ears for any advice/recommendations.
I'm going to search the forums on installation procedures. This is a project that I might undertake so long as it wouldn't interfere with my wheels/tires and also didn't require a lot of extra measures like camber adjustment. An alignment, I would, of course, be willing to do.
I've driven all over your province dropped 1.5"
My recommendation should you decide to lower, go with something like Eibach Prokits at 1.1". These are the springs that Toyota Canada actually sold for lowering springs, not TRDs at 1.25"
My recommendation should you decide to lower, go with something like Eibach Prokits at 1.1". These are the springs that Toyota Canada actually sold for lowering springs, not TRDs at 1.25"
Sage advice, I believe. I did see a set of other brand springs that stated 1.3" drop and I kinda liked that idea, but 1.1" sounds even better. I expect thse Eibach springs ain't cheap though. Will search online. Thanks!Originally Posted by WeeYari ↑I've driven all over your province dropped 1.5"
My recommendation should you decide to lower, go with something like Eibach Prokits at 1.1". These are the springs that Toyota Canada actually sold for lowering springs, not TRDs at 1.25"
👍
Megan Racing isn't the highest level brand, but it's good, solid quality and doesn't break the bank. I think they provide a 1.5" drop on these cars.
Megan Racing isn't the highest level brand, but it's good, solid quality and doesn't break the bank. I think they provide a 1.5" drop on these cars.
Thanks. Will have a look at those.Originally Posted by ern-diz ↑👍
Megan Racing isn't the highest level brand, but it's good, solid quality and doesn't break the bank. I think they provide a 1.5" drop on these cars.
Megans are what I was running. Decent ride quality with 1.5" drop front and rear. Problem with Megan is their powder coat sucks. Cracks and begins flaking off in second year.
Sent from my Elite_5_5_Octa using Tapatalk
Sent from my Elite_5_5_Octa using Tapatalk
Ah, good to know about the ride quality. I've always been surprised that powder coat would even last that long given the continuous flexing.Originally Posted by WeeYari ↑Megans are what I was running. Decent ride quality with 1.5" drop front and rear. Problem with Megan is their powder coat sucks. Cracks and begins flaking off in second year.
Sent from my Elite_5_5_Octa using Tapatalk