Replies continued
Jason@SportsCarDebary, FL · Oct 22, 2017#51Yeah, the safe way off is down pit road. You are one of the lucky ones that gets a second chance. ;)
Why is there like a 20mph difference between gps and obd speed in your data?
dengThread starterMI · Oct 22, 2017#52Haha pretty much why I packed up, cheered on my buddies, and left early for the day. It was such a nice day too.
I'm guessing it's because I instinctively went both feet in and ABS was activating during the slide, so the ECU sees a slower wheel speed than the velocity I was traveling. I think haha.
tmontagueCaledonia Ont. · Oct 23, 2017#53Geeze you are a lucky man. Gald you and the car are okay. Did you try throttling out of the over steer?
How do you decipher the lap data diagram on Harry's lap timer? That's the app I use but I haven't ever fully under stood the lap data image it gives you
dengThread starterMI · Oct 23, 2017#54Thanks man. I went both feet in on the clutch and brake pedal right when I started to spin.
I have a hard time looking at the data on my phone. Shoot, I'm still trying to figure out this software lol. Might be better to export the data and look at it on the PC using another software.
ArmstrongRacingSan Diego · Oct 26, 2017#55 Originally Posted by
Jason@SportsCar ↑ Sideways across the track, then into the dirt, you are lucky that did not roll. :(
Did you have data to pull your mph and lap times?
B Spec record is a 1:44.3, considering you are on street tires (I assume you still are) you were clicking off pretty good times.
This.
Deng is certainly a good driver with a well setup car, he is on RE71R tires. 👍
dengThread starterMI · Oct 26, 2017#56 Originally Posted by
Jason@SportsCar ↑ B Spec record is a 1:44.3, considering you are on street tires (I assume you still are) you were clicking off pretty good times.
I totally overlooked this part of your post. Thanks! and I am still running on street tires.
Originally Posted by
ArmstrongRacing ↑ This.
Deng is certainly a good driver with a well setup car, he is on RE71R tires. 👍
Thanks man, I still need a lot of seat time though 👍
and I'm running 205/50 Dunlop Direzza Star Spec IIs at the moment.
Thanks again guys, it means a lot coming from the both of you.
ArmstrongRacingSan Diego · Oct 26, 2017#57 Originally Posted by
deng ↑ I totally overlooked this part of your post. Thanks! and I am still running on street tires
and I'm running 205/50 Dunlop Direzza Star Spec IIs at the moment.
oh.....oops lol
dengThread starterMI · Oct 26, 2017#58No worries, I wish I still had the re71rs. I killed them from not adjusting tire pressure, they were too high. :( the Star Specs were on sale, so I scooped them up.
And here's a picture that Caliphotography took.
1 attachment not included in this copy
ArmstrongRacingSan Diego · Oct 26, 2017#59 Originally Posted by
deng ↑ No worries, I wish I still had the re71rs. I killed them from not adjusting tire pressure, they were too high. :( the Star Specs were on sale, so I scooped them up.
And here's a picture that Caliphotography took.
Ive done that before, to my z2's. still got a to of racing out of them though. picture looks awesome man, i wasnt too pleased with mine👎
atomic_hojiKincardine, ON, Canada · Nov 12, 2017#60Nice update man. 👍
Glad to hear all is well for both you and the car after your off - pretty sure I'd need a fresh set of underoos after a spin that like at a nearly a buck sixty..! lol
-- Adam
dengThread starterMI · Jan 15, 2018#61Not much of an update.
Ever since owning the car, the driver's side rear toe has too much toe in, it's off in the .30* range while passenger side is around .15* I'm surprised the off at Big Willow didn't make it more out of spec.
Rear:
Toe
L \ R
.30 \ .15
Camber
L \ R
-.7 \ -.9
I'm experimenting with shims because the idea of using just washers doesn't sit well with me. At least with shims, there is more surface area for the hub assembly to make contact with the torsion beam assembly.
These shims are cut out of .25mm shim stock. There are 6 pictured in the attach photo, but I only used 2 of these shims, and that was enough to kick the toe out from .30* to -.09*. I'm only using one shim now. I might have to pick up some .1mm shim stock and stack again. I really need an alignment rack in my garage.
#torsionbeamwoes
1 attachment not included in this copy
Jason@SportsCarDebary, FL · Jan 15, 2018#62 Originally Posted by
deng ↑ Not much of an update.
Ever since owning the car, the driver's side rear toe has too much toe in, it's off in the .30* range while passenger side is around .15* I'm surprised the off at Big Willow didn't make it more out of spec.
Rear:
Toe
L \ R
.30 \ .15
Camber
L \ R
-.7 \ -.9
I'm experimenting with shims because the idea of using just washers doesn't sit well with me. At least with shims, there is more surface area for the hub assembly to make contact with the torsion beam assembly.
These shims are cut out of .25mm shim stock. There are 6 pictured in the attach photo, but I only used 2 of these shims, and that was enough to kick the toe out from .30* to -.09*. I'm only using one shim now. I might have to pick up some .1mm shim stock and stack again. I really need an alignment rack in my garage.
#torsionbeamwoes
No need for a rack, just get a set of Smart Strings and a Smart Camber gauge, never visit the alignment shop again. *especially important for those after off-track excursion checks in the paddock.
I did a similar thing, just bought different gauge stainless and cut shims to set the toe to zero. 👍
http://www.smartracingproducts.com/ dengThread starterMI · Jan 16, 2018#63I've been debating about running 0 rear toe, but since it is my daily maybe a little toe in for highway stability. 🤷
Either way, the smart string would be a good investment when I'm playing with shims. I feel it's going to be a steep learning curve for me initially. I figure once the bars are dialed in to the vehicle, future set ups will be a breeze.
Jason@SportsCarDebary, FL · Jan 16, 2018#64 Originally Posted by
deng ↑ I've been debating about running 0 rear toe, but since it is my daily maybe a little toe in for highway stability. 🤷
Either way, the smart string would be a good investment when I'm playing with shims. I feel it's going to be a steep learning curve for me initially. I figure once the bars are dialed in to the vehicle, future set ups will be a breeze.
Zero in the rear is not an issue for street use - its more about reducing rolling resistance than changing the balance of the car.
Any time you use them on a new car for the first time it adds about 30 min just to dial in the bar setup, after that its easy. One of the best tools we ever bought.
dengThread starterMI · Jan 17, 2018#65Alright Jason, you talked me into running 0 toe all around, and I also ordered the smart strings lol. I have some stainless 0.05mm shim stock coming, so it's going to be like playing with razor blades! 😛
ArmstrongRacingSan Diego · Jan 18, 2018#66 Originally Posted by
Jason@SportsCar ↑
I did the same thing, 0 rear toe, and "some" rear camber lol
dengThread starterMI · Jan 27, 2018#67Best use of an 18mm and 23mm socket.
Front and rear toe set to 0. 👍
1 attachment not included in this copy
ArmstrongRacingSan Diego · Jan 29, 2018#68Very Nice!
tmontagueCaledonia Ont. · Jan 29, 2018#69Let me know what you think of the smart string, I may be interested in it down the road
dengThread starterMI · Mar 1, 2018#70Highly recommend the smart strings, I pretty much used it enough times to pay for itself.
Well, using the Yaris for HPDE has come to an end for now.
I received my start date at my new job location in Michigan in August, so I'm going to be busy with relocation these next few months.
Anywho, daily cross country spec. I tried going for that new school old school mash up, I like it.
Enkei Compe 15x7 +38
195/55R15 Yokohama Avid Envigor
Tsurikawa subway handle from my old drift car. I threw it on for fun. I think it looks pretty cool, but I'm not low enough for it to touch the ground. 👎
I'm going to remove my Cusco Coilovers this weekend and swap in the factory struts/shocks with the R*SR springs that I still have. It should be more comfy with a little rise in the ride height (sadly lol).
2 attachments not included in this copy
RunethecursedSocal · Mar 3, 2018#71Looks sharp sad to see you move to Michigan but its gonna be better living out there. I cant wait to leave the coast myself.
dengThread starterMI · Mar 3, 2018#72Yeah, I'm excited to move. I've been in SoCal all my life, so I'm looking forward to MI. I see it as an opportunity to live somewhere new.
Plus, no smog! Yaris is going to be the beater daily while I get another rwd sedan and 1j swap, yes! 👍
yarisugiハワイ · Mar 3, 2018#73First thing that came to mind was winter and road salt... :(
WhiplashOntario · Mar 3, 2018#74^Aha yeah...potholes.
dengThread starterMI · Jul 1, 2018#75Sold the Yaris. FS thread coming soon.
yarisugiハワイ · Jul 1, 2018#76Whaat?!!!
I can't find you on IG either.
You ok?
RunethecursedSocal · Jul 1, 2018#77Wait what
dengThread starterMI · Jul 1, 2018#78Thanks for the concern guys, but everything is fine. I'm trying to get rid of all my debt for this fresh start in Michigan. :)
yari, shot you a request to follow.
ern-dizCA all day · Jul 2, 2018#79Glad to hear all is well, Deng. Like CT, we've missed you around this place. If you have a chance, jump on Wheelwell.com. I'd give you a follow there, too.
Dodge Aries KMachesney Park, IL · Jul 2, 2018#80You sold it? Oh no! I'll be looking for your sale thread but it makes me sad.
dengThread starterMI · Jul 3, 2018#81Don't worry I'll still be around. I love the little 1NZ, but I'mma get something a little more my taste. I might have to pick up an Echo Sedan in CA and ship it MI. ;)
ern-dizCA all day · Jul 3, 2018#82 Originally Posted by
deng ↑ Don't worry I'll still be around. I love the little 1NZ, but I'mma get something a little more my taste. I might have to pick up an Echo Sedan in CA and ship it MI. ;)
That would be brilliant.
RunethecursedSocal · Jul 3, 2018#83 Originally Posted by
Dodge Aries K ↑ You sold it? Oh no! I'll be looking for your sale thread but it makes me sad.
Buy my car ;)
Kaotic LazagnaCentral Valley, CA · Jul 4, 2018#84What are you planning on replacing it with? I presume something that's AWD/4WD?